ELEX euro - Thermofilm
Contents
1. E nd gt AE euro THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au FLEX euro 4 4 Electrical connection This heater is suitable for 230 240V Please observe national standards the regulations of your local electricity supply company as well as data on the rating label Electrical safety The ELEX CULO convective panel heaters are IP24 protected against splashing water In humid areas such as bathrooms the power socket must be installed at least 25cm above floor level Note the details on the rating plate The voltage supply must match the requirements on the rating plate The supply cable must be correctly sized The heater must be connected to a socket outlet or permanent terminal box at least 10 cm to one side of the heater Please note in general Where the ELEX CUIO convective panel heater is fitted in a room with a bath or shower ensure the safety zone defined in IEE Regulations is applied in accordance with the details on the rating plate To avoid hazards if the power cord of the appliance exhibits visible damage it must be replaced by the manufacturer or his service agent or a qualified electrician 4 5 Safety Notes The ELEX CULO convective panel heater is equipped with a safety cut out that switches the heater off if it overheats Once the heater has switched off due to overheating remove the cause of the fault e g blocked air grids When2. ensure that hands are dry before operating or adjusting any switch on the product or touching the plug and mains supply connections e Never leave the appliance unattended when connected to the mains power supply e Do not cover NEVER use the heater to dry clothes or similar articles e Do not position the appliances close to curtains or other combustible materials Keep combustible material such as furniture cushions bedding paper clothes curtains etc at least 0m away from the heater e The most common cause of overheating is deposits of dust or fluff in the appliance Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning air vents and grilles e This appliance heats up when in use To avoid burns do not let bare skin touch hot surface Switch off and let cool down before moving Store the heater in cool dry location when not in use e Do not use this appliance with a programmer timer or any other devices that switches the appliances on automatically e Do not use an extension cable with this appliance e Do not use the appliance in rooms less than 4m area e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety e Children should be supervised to ensure that t
3. the heater has cooled down for several minutes it will restart automatically If the heater then cuts off again switch off the heater and call an authorized serviceman 5 Warranty The below Warranty Terms and Conditions apply for New Zealand and Australia only For international warranty please refer to international warranty terms and conditions Thermofilm warrants to the original owner that ELEX CULO products will be free from defects in materials and workmanship for a period of 24 months for residential use from the date of purchase in accordance with the following warranty terms and conditions For commercial use warranty is 2 months Provision of this warranty is subject to e The ELEX CULO product must be installed in accordance with the Installation Instructions and relevant electrical standards and codes e The ELEX CULO product must be maintained and cleaned according to instructions detailed in the Installation Manual e There is no warranty expressed or implied with regard to capacity requirements The selection of the unit or units depends entirely upon the system design and capacities as determined by the purchaser e The customer has not repaired opened or altered the product in any unauthorised manner e This warranty excludes damage to the product or components arising from circumstances outside the control of Thermofilm including but not limited to where the product is not used for intended purpose where the product
4. FLEX euro ELEX euro CONVECTIVE PANEL HEATER Rev C JULI3 USER MANUAL Models ELEX euro 2400 ELEX euro 2000 ELEX euro 1500 ELEX euro 1000 FAILLIOAAN ODO TABLE OF CONTENTS Important Safety Instructions 2 Specification Data 3 Operating Instructions 3 1 Control Panel Guide 3 2 Switching on the Unit 3 3 Programming the Timer 3 3 1 Programming the Clock 3 3 2 Setting the Temperature 3 3 3 Selecting the Constant Heating Operation 3 3 4 Selecting the Constant Frost Protection Operation 3 3 5 Setting the Self Set Weekly Operation 3 3 6 Adjust the Temperature of a Running Programme 3 3 7 Changing Time for Daylight Savings 3 3 8 Programme Back Up 3 3 9 Locking the Control Panel 3 4 Safety Notes 3 5 Maintenance 4 Installation Instructions 4 Installation Location 4 2 Wall Mounting Bracket 4 3 Castor Wheel Set 4 4 Electrical Connection 4 5 Safety Notes 5 Warranty y gt Z m m L m gt m 2 Wn THERMOFILM g euro THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au FLEX euro I Important Safety Instructions e Prior to installing and operating the heater read these instructions carefully and retain for future reference e Indoor use only e Ensure the rated voltage is 230 240V e Do not install the heater directly below a socket e Always operate heater in an upright position with the control panel at the top If
5. accept liability for failure of any goods supplied which have not been installed and operated in accordance with the manufacturer s instructions These installation instructions belong with the heater and must be handed on to the purchaser if the heater is sold 4 1 Installation Location The ELEX CULO convective panel heater was designed to be installed in a residence Please ask your distributor before using it for any other purpose The ELEX CULO convective panel heater should be installed according to normal trade practice and in compliance with legislation in relevant country The panel convector is CLASS I and is protected against splashed water IP24 Therefore it can be installed outside the shaded area shown in the bathroom area Volume 3 Ensure the safety zones mm in diagram left hand side are kept free If the wall covering is laid on foam a spacer the same thickness as the foam must be placed under the panel heater s support This ensures there is free space behind the panel heater to make sure its control settings are not adversely affected Beuro THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 ae Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au FAILLIAAN ODO y gt Z m m L m gt m 2 Wn FLEX euro The ELEX CUFO convective panel heater must not be installed immediately below a wall socket The heater must be connected to a socket outlet or permanent termina
6. ault programme of CO Constant Heating Operation 3 3 2 Setting the temperature Press the temperature setting button L J The centre of the digital clock face will flash with the a v heating operation and temperature setting e g CO 21 Use the up and down buttons to set the required temperature Note The default temperature is 21 C Press the temperature button L again to complete the temperature setting 3 3 3 Selecting the Constant Heating Operation The constant heating operation is the default setting of the heater and this will run when the heater is used for the first time or after a lengthy absence of power The temperature setting may be altered as per section 3 3 2 To select this setting press the mode button L Use the up and down LY buttons to select the CO programme The temperature setting may be altered as per section 3 3 3 MODE Press the mode button again to terminate the setting The mode symbol will stop flashing The mode is now active and will run in real time g euro THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au THERMOFILM iin n ee FAILLIOAAN ODO y gt Z m m L m gt m 2 T FLEX euro 3 3 4 Selecting the Constant Frost Protection Operation To protect against freezing temperatures in cold climate areas you can programme the heater for frost protection by re
7. ducing the set temperature to 5 C while the heater is in CO mode When the temperature is set to 5 C the ka symbol will display on the screen and the heater will operate when the room temperature falls below 5 C 3 3 5 Setting the Self Set Weekly Operation This function allows you to program for ON OFF times 24 hours a day 7 days per week MODE Press the mode button The mode symbol will flash Use the up L or down L J button to select the programme mode of SS Press the mode button again to complete the setting The mode symbol SS will stop flashing Selecting the Day FAILLIAAN ODO PROG Press the programme button The symbol will appear around the current day e g M Monday The time will show 00 00 midnight and the symbol PROG are displayed If you want the programme to start another weekday for example the Tuesday press the timer button consecutively until the symbol surrounds T Tuesday on the screen Selecting Times for a Full 24 hour Day Note The zone for OFF is blank and the zone of ON is black on the digital clock face diagram The up button is used for setting the ON Zone and the down button Y J is used for setting the OFF Zone The timer will start at 00 00 and each push of the up or down button will advance the clock by one hour Push the appropriate LAJ or L7 button to set the desired ON or OFF time for the day Yo
8. has been rectified in any way incorrect installation incorrect power supply damaged caused during delivery misapplication misuse abuse vandalism lack of maintenance g euro THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au THERMOFILM FAILLIAAN ODO y gt Z m m L m gt m 2 T FLEX euro or accident e Thermofilm s obligations under this warranty are limited to repair or replacement at Thermofilm s factory of any components of the product which Thermofilm identifies to its satisfaction to be defective e Transportation charges involved in return of the product to the Thermofilm factory or any other location authorised in writing by Thermofilm is the sole responsibility of the customer e All products are inspected and tested before despatch and are at the risk of the purchaser after the shipment from the Thermofilm factory if not delivered by Thermofilm to destination e Discolouration of the surface may occur after a period of time this does not constitute a warrantable event e No products or components will be supplied in advance of an examination of the faulty product or components by Thermofilm or an authorized representative of Thermofilm e Thermofilm does not participate in any site related costs or labour expenses incidental to replacement of parts repairing removing installing servicing transportation or handling of part
9. hey do not play with the appliance e If used as a portable heater do not use in the immediate surroundings of a bath a shower or a swimming pool FAILLIAAN ODO y gt Z m m L m gt m 2 Wn THERMOFILM g euro THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au FLEX euro 2 Specification Data ELEX Euro 1000 ELEX euro 1500 ELEX euro 2000 ELEX euro 2400 Power W ow mow 2 000w 2400W Voltage V as aR aa OE 240V 50Hz 420 x 440x105 580x440x105 740x440x105 1000x 440x 105 3 Operating Instructions The control panel features an accurate electronic thermostat and 7 day programmable timer This timer has a constant heating operation constant frost protection operation and a self set weekly operation programme 11 10 9 87 654 3 2 1 ove I F FAILLIOAAN ODO PROG a COPY 3 1 Control Panel Guide I Main Power Switch 1 0 ON OFF 2 Unit Power button ON OFF 3 Copy button 4 Down button 5 Up button 6 Temperature button 7 Timer button 8 Programming button 9 Mode Selection button 10 LCD screen I I Power On light 3 2 Switching on the Unit Press the main power switch 1 on the right hand side of panel Press the button 2 on the control panel This turns the unit ON and the LCD screen 10 will illuminate displaying M Monday and 12 00 as the default day and ti
10. k Up In the event of a mains power failure or long period when the heater has been turned off the timer and SS programme must be reset by the user All other pre set programs and default temperatures will be saved 3 3 9 Locking the Control Panel Press the mode button L to make the chosen program SS or CO flash 3 Press the programme button L and the timer button at the same time for around three 3 seconds A padlock symbol E displayed on the screen indicating the all buttons are now locked To unlock the control panel press the programme button L and the timer button at the same time for around three 3 seconds and the padlock symbol will disappear 3 4 Safety Notes The air outlet must not be obstructed For safety reasons the upper and lower air grilles must never be covered with items such as washing nor obstructed by items in close proximity see figure to right Objects should not be leant Let against the unit nor placed between the unit and the wall Never leave combustible materials such as wood paper textiles or flammable items such as wax petrol aerosol cans etc in the vicinity of the warm air outlet As with all similar heaters the flow of rising air may cause discoloration of the wall The appliance must not be operated e In areas which are subject to the risk of fire or explosion due to chemicals dust gases or vapors THERMOFILM g euro THERMOFILM AUSTRALIA 27 R
11. l box at least 10cm to one side of the heater If the heater is installed in the Bathroom or in humid area the socket outlet or permanent terminal box must conform to the IP24 requirement The ELEX CULO convective panel heater must not be installed in a draught likely to affect the control settings under a ventilating fan etc 4 2 Wall Mounting Bracket The wall mounting bracket is oriented centrally See RHS diagram Step Loosen the locking plate screw and rotate the locking plate out of the fixing slot See RHS images Then remove the mounting bracket from the heater FAILLIOAAN ODO Step 2 Use the wall mounting bracket as a template for marking the fixing holes Position the mounting bracket in the correct position on the wall and mark the screw holes through the 4 mounting holes See RHS diagram Step 3 Install the 4 fixing devices in the wall ensuring they are more than adequate to safely fix the heater to the wall ST4 expansion screws are suggested Step 4 Fix the bracket firmly to the wall using all 4 mounting locations Step 5 Mount the heater on the bracket so the bracket protrusions fix into the 4 slots on the back of the heater See RHS diagram Rotate the locking plate into the fixing slot and tighten the screw To remove the heater reverse the above operation 4 3 Castor Wheel Set Part list Castors 4PCS Screw 4PCS mT Support 2PCS SYUdlVadaH 143NV d
12. me setting y gt Z m m L m gt m 2 Wn Constant Heating Operation at 21 C is the default operation setting Note The red ON indicator light I 1 illuminates when the heating element is operating Upon first use the heater may give off some fumes this is normal Ensure that the room is ventilated for example open a window euro THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au THERMOFILM FLEX euro 3 3 Programming the Timer The timer must be set in order to use the Self Set Weekly Operation Programme 3 3 1 Programming the Clock Day Setting Press timer button L J The symbol will flash around M Monday Use the up A and down Y J buttons to move the symbol to the correct day Monday Tuesday Wednesday Thursday Friday Saturday Sunday DPT Az Note The will flash when used for the first time or after a lengthy absence of power and the red ON light will glow Hour Setting a Press timer button L J The hour number will flash Use the up and down L J buttons to set the correct hour Minute Setting Press the timer button L J The minute number will flash Use the up LA and down LY buttons to set the correct minute Press the timer button again to complete the timer setting The control panel will show the current time and the unit will operate under the def
13. mperature of a Running Programme The temperature sensed by the thermostat sensor is relative to the position of the heater in the room If the actual temperature is higher than the setting compensate this by adjusting the temperature setting g euro THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au THERMOFILM iin age ae FAILLIOAAN ODO y gt Z m m L m gt m 2 Wn FLEX euro For example if the comfort temperature is set at 21 C but the actual room temperature is 24 C compensate for this by lowering the setting to 18 C Similarly increase the temperature setting if the actual room temperature is lower than the setting Press the temperature button J The temperature symbol will flash a v l Use the button up or down button to adjust the comfort temperature Terminate by pressing the temperature button J again The control panel will now show the correct day The programme is now active and is running on real time 3 3 7 Changing time for Daylight Savings Press the timer button twice to make the hour display flash l N In Summer time press the up button to advance the timer clock one hour In Winter time press the down button to set the timer clock back one hour Terminate the operation by again pressing the timer button J twice so that the current program is displayed on the panel 3 3 8 Programme Bac
14. o have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure All warranty requests for repairs or replacements must be accompanied by a complete Warranty Claim Form available from Thermofilm together with proof of purchase and where possible photos of the installation and the heater returned to the place of purchase In the event of a warranty claim the goods need to be returned to the distributor retailer for repair replacement Contact Thermofilm Australia Pty Ltd 27 Rosalie Street Springvale Victoria 3171 Australia Telephone 03 9562 3455 Email info thermofilm com au THERMOFILM euro THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au FAILLIOAAN ODO y gt Z m m L m gt m 2 Wn
15. osalie Street Springvale VIC 3171 Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au FAILLIAAN ODO y gt Z m m L m gt m 2 Wn FLEX euro e In the immediate vicinity of pipes or containers which carry or contain combustible or potentially explosive substances For this reason the minimum clearance intervals must not be undercut In workshops or other areas in which the odor of waste gases oil petrol etc might occur or in which work is carried out involving solvents and chemicals there is a risk of sustained odor burdens being engendered and possibly of dirt contamination occurring Before using any materials which produce flammable gases or vapors e g laying or sealing parquet or PVC flooring or when using spray polishes spirits and similar materials ensure the heater is switched off 3 5 Maintenance Do not use abrasive or aggressive cleansers to clean the heater Use a vacuum cleaner regularly to clean the upper and lower air grids 4 Installation instructions The ELEX EUTO convective panel heaters are electric heaters designed to be mounted on the wall or freestanding using the supplied castor wheel set These units are suitable for heating enclosed indoor rooms such as bedrooms studies offices living areas and bathrooms ATTENTION The installation electrical connection and first operation of this appliance should be carried out by a qualified installer The company does not
16. rrect day The programme is now active and is running on real time Note You must programme the full 24 hour ON OFF period until the time reaches 00 00 for the timer to function correctly If you go past the 00 00 and move to 01 00 you will need to programme the 24 hour programme for that day again Copy the 24 hour program If you would like the same 24 hour program to work for another day or days in the week the programme can be copied onto the selected day For example you have just created a 24 hour programme for Monday and you wish to copy this Monday programme to Tuesday Step Press the programme button L and then press the _ _ button to move the to M Monday Step 2 Press the copy button L The symbol COPY will appear on the LCD screen The around the M will flash If you would like to cancel the COPY order please press the button again the symbol COPY will disappear accordingly Step 3 Press the timer button J to move the L J around T Tuesday The will appear around the M and T Step 4 Press the copy button to complete the operation The COPY and M symbol will disappear To copy this same Monday programme to another day repeat from Step 3 PROG Press the button to terminate the COPY function The control panel will now show the correct day The programme is now active and is running on real time 3 3 6 Adjust the Te
17. s to complete products and assumes no liability on parts repaired or replaced without written authorisation Thermofilm shall not be liable for any default or delay in performance of its warranty obligations caused by any circumstances beyond its control including but not limited to judicial or government restrictions strikes fires floods abnormal weather conditions delayed supply of components Should products be determined as damaged on arrival immediately notify the transport company of the condition and have them noted on the freight documents If damage is discovered after unpacking demand immediate inspection by the transportation company and insist that a record of the damage is made on the freight documentation The customer warrants using the product in accordance with e Any instructions provided to it by Thermofilm from time to time e All government and local regulations including but not limited to all relevant electrical environmental laws and regulations governing the installation storage use handling and maintenance of the goods e All necessary and appropriate precautions and safety measures relating to the installation storage use handling and maintenance of goods Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled t
18. u must programme the full 24 hour ON OFF period until the time reaches 00 00 for the timer to function correctly PROG Press the programme button to complete the setting for the day For example you would like to make the unit work from 1 00 to 4 00 1 00 13 00 and from 17 00 to 23 00 Step Press the button YJ The time will change from 00 00 to 1 00 and the zone between 24 00 to 1 00 will be blank OFF y gt Z m m L m gt m 2 T Step 2 Press the button J until the time advances to 4 00 and the zone between 1 00 and 4 00 be black ON Step 3 Press the button Y J until the time advances to 11 00 and the zone between 4 00 to 1 00 be blank OFF Step 4 Press the button J until the time advances to 13 00 and the zone between 1 00 to 13 00 will be black ON g euro THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au THERMOFILM FLEX euro Step 5 Press the button Y J until the time advances to 17 00 and the zone between 13 00 to 17 00 will be blank OFF Step 6 Press the button J until the time advances to 23 00 and the zone between 17 00 to 23 00 will be black ON Step 7 Press the button Y J until the time advances to 00 00 and the zone between 23 00 to 24 00 will be blank OFF Step 8 Press the programme button L to complete the setting for the day The control panel will now show the co
19. using castor wheel set heater should be positioned on a flat horizontal surface e Arrange cord away from traffic areas so that it will not be tripped over e Do not place the cable under carpets rugs e Do not remove plug from power socket by pulling the supply cord Always grip plug e Do not operate this appliance if the cable or plug becomes damaged In case of heater fault or damaged supply lead the appliance should be returned to the distributor manufacturer for repair Ensure the appliance is switched OFF before connecting to the mains power supply e Do not cover or restrict airflow to the inlet or outlet grills in any manner as the appliance may overheat and become a fire risk e Do not insert or allow foreign objects or metal utensils to enter any grill opening as this may cause an electric shock or fire damage to the appliance e Do not operate in areas where gasoline paint or other flammable liquids are used or stored e Switch off the power supply and unplug from the mains socket when not in use before cleaning or changing accessories e To prevent overload and blown fuses do not plug other appliance into same power outlet receptacle e Do not immerse in liquid or allow liquid into the interior of the appliance as this could create an electric shock hazard e Do not reach for an appliance that has fallen into water Switch off at supply and unplug immediately e Do not operate appliance with wet hands Always
Download Pdf Manuals
Related Search