EN_Short user manual (ADVANCED interface)
Contents
1. arm the system with the person staying inside of the premise gt The interior zones are left disarmed if anyone opens door won t be the entry delay and the alarm will sound This arming mode is effective when the door and windows are secured by the opening sensors or there are eD indicata installed glass break detectors Arming F key for EU countries cd ENT Pin Ent for non EU countries is available cd ENT Via Menu 81 Arming D Night END PIN Gi ENT Parts J ENT Partial Arming with F key Select the arming mode by pressing or Leg keys A Away arming AA Stay arming AAA Max Away arming AAAA Forced arming C Night arming When arming mode is selected with the keys 1 2 3 4 select the partitions which must be armed When partitions are selected press ENT Example Only the first partition is armed This kind of arming is available in 2 storied house when at night the ground floor isn t used all sensors of this partition are armed When somebody opens doors will be an entry delay Arming D i LCD indication With 4 key select the arming When arming mode is selected Press 1 key to perform mode press the number of arming process partition amp 1 Partial Arming from Menu This is universal way of arming which enables to arm selected partition in desired arming mode In case of partial arming Green LED will blink slo2. before alarm If the system has smoke detector and alarm was caused by smoke which was raised by domestic reasons the system will start alarm nevertheless it was armed or disarmed The only way to clear alarm is possible by bypassing of smoke detector see 2 page Bypassing zone B 2way entering PIN code After performed alarm clearing action siren stops to sound alarm LED goes off the system will be disarmed ifit was armed before entering PIN code When all partitions which are controlled by User are disarmed it s not recommended to use PIN for alarm clearing because is possible casual arming armed Event log review F30 F31 All events which are concerned with protected premises and status of the system are stored in the event log Reviewing event log Nz F key CIB ALARMS events J FAULTS events Via Menu e gt gt gt Event Log E Alarm Event E PIN ENT To display time or date event press the key next event is selected the 4 key Electronic notebook memo review F09 Allimportant contact information phone No e mail Installer can write outon keypad Review F key CF o Jo JET 1 record C gt 2 record C gt 3 record 4 record 5 record C gt Via Menu Memo Ent 1 record C 2 record gt 3 record 4 record 5 record C gt SECOLink MAS 800 KM20B KM20BT KM20
3. zone Enter the zone number you would like to bypass THIS MUST BE A TWO DIGIT NUMBER The zone will be marked as x To bypass the zone for a long time permanent the last number should be pressed and held for 2 sec The zone will be marked as 4 When all zones are marked press key The same actions can be performed by choosing the zone with the keys or and by marking with the key short press temporal long permanent Z Abort arming For selecting also for aborting arm procedure the system SECOLink has the ctr key If the exit delay is in process and you want to abort arming press the key enter PIN and confirmit with the Enkey Arming system with troubles EU standards unexpect using of the system which has troubles When Yellow LED is on the arming is impossible in the ways which were described earlier It is necessary immediately eliminate troubles also armed inform CMS and company which had installed the system The system detects troubles in own modules also it detects and other common troubles like 230V disappearance in AC line disconnected phone line because of repair battery discharge In exceptional cases is possible to bypass the troubles for a short time and arm system as usual It can be done this way 3 Press the key once message about the trouble will be shown on the display then press er key again Yellow Trouble LED starts to blink fast The blinking duration is 30 sec
4. GT keypad Intruder alarm system Short user manual a rE s Sensor operation testing testing zones F22 It is recommended to do sensor work test at least one time per month During a test itis necessary to makea violation of zone it means to open door or windows which have magnetic contacts or to simulate movement near the motion sensor Glass break detector can be tested by hard clapping hands Testing F key CE 2 2 Ent Pinse ENT Via Menu EN lt 4 4 4 lt 4 4 Tests EN Burg Zone Tes ENT PiN ENT Testing zone Testing zone is not violated is violated Zones which were violated are checking by pressing the key test finishes by pressing Lr Permission to make changes of the system service mode entry F33 For security reasons Installer will have permission to make changes of the system setting only after User approves it by entering his PIN F key 3 2 amp 7 Enable Service User PIN Cr Ex ServicePIN Via Menu Ev lt 4 Service mode N Enable Service User PIN Pit Ent ServicePIN PIN Activated User PIN code changing F20 The manufacturer provides the system with 4 digit number default PINs Each user has default PIN according his number in the system For example the default PIN for the first User will be 0001 for the second User 0002 and etc After installation itis strongly
5. SECOLink MAS 800 KM20B KM20BT KM20GT keypad Intruder alarm system Short user manual SECOLink There is 1 partition in the MAS 800 alarm system This partition isn t armed and there is one armed System s state Date Time zone which is violated LED indication Pre alarm indication pre alarm trouble Emergency keys oh C w a i T JAL 3 J CLR Status of the system Entry Doors are open i i i gt 6 J 4A Beets Functional keys NZ NN Main menu There are 4 partitions in system F keys navigation keys the first partition is armed in the Stay mode Cc 8 9 Vv gt the second partition is armed in the Night mode the third partition is armed in the Max Away mode a y the fourth partition is armed in the Away mode L F L L 0 J ENT Environment temperature for KM20BT KM20GT t This key is used for partition review This key is used for zone review also for marking all partitions or also for marking the partitions and selecting another element L other elements of the system t for example for User selecting for example for marking zone Status of the system SYSTEM IS ARMED which ll be bypassed Functional keys for quick and comfortable control of the system The SECOLink Security system comes with a standard set of function keys F keys that are described below This al
6. essing the Jkey on selected zone The chime zone will be marked as Via Menu ENT 4 4 lt 4 4 lt 4 Options END v gt Chime ENT PIN ENT v gt v gt J ENT Setting Date and time F21 F key FJ 2 e1 E Date and Time Ent enter date and time EN Via Menu ENT 4 4 4 4 Options Enn ET Date and Time Pin nt enter date and time ENT Temperature correction on keypad display F11 only KM20BT KM20GT If the keypad shows an incorrect environment temperature it is recommended to make temperature correction which can be done by entering value of temperature measured with domestic thermometers The correction can be made Via Menu EN lt 4 lt 4 lt 4 lt 4 Options ED Temperature lt 4 Temper correction ENT PN J ENT enter temperature value EnD Activated Users review F23 After system installation is recommended to review how many Users can control the security system F key CF 2 3 ENT PIN ENT v gt Status C C Ce Ce Via Menu EN 4 4 4 4 Options ENT Users Ent gt Edit User ENT Pins Ent gt Status LCD display will show User number for example U01 and mode Enabled or Disabled All Users who have mode Enabled can control system or it s partitio
7. g PIN ENT When part of partitions are armed and the entry door weren t opened after entering PIN itis necessary to make decision either to arm disarmed partitions or to disarm armed ones Full disarming PN Ent V gt Disarming D All partitions D Partial disarming PN n gt Disarming gt Selected parti Parts END Disarming when staying in protected premise BB or FO Nevertheless are there all partitions armed or not all partitions which are controlled by User will be disarmed Disarming F key CF Co J ENT Pins J ENT Or B4 Ba ENT PIN ENT The first partition disarming when staying in premise BB1 Nevertheless are there all partitions armed or not the first partition which is controlled by User will be disarmed Disarming F key Bal Bele 1 ENT PIN ENT The second partition can be disarmed with BB2 both partitions with BB12 iE ie BIE Alarm clearing If an alarm has occured on the display appears message Alarm with an explanation what reason caused it Alarm LED is turned on the siren starts to sound and report about alarm is sending to CMS or to alarm the User There are 2waystoclear alarm and turn off red LED 1 way pressing the CLR PIN ENT After performed alarm clearing action siren stops to sound alarm LED goes off the system status remains troubla the same as was
8. lows you to carry out your most frequently used functions by using only one or two buttons This also allows you to avoid system management via the Menu navigation During the installation you can create individual F keys which can be adapted for the needs of the protected building and the user To view the current list of F keys press key and then keep pressing amp 4 and keys F key F key the name Ways of arming The system can be armed by three ways F key via Menu entering PIN code The system function which is controlled by F key can be called by pressing the F key combination and Ent or by pressing and holding the last letter number of the F key combination When Arming is activated via Menu it s necessary to mark the partitions which will be armed mark the partitions with or and confirm with When arming is activated by Entering PIN code it will be armed in Away mode Arming mode Away A This arming mode is used when you want to protect a premise when nobody will be staying inside After arming all zones will be protected After using the door will be entry delay time for disarming Arming F key for EU countries 42 ENT Pins ENT for non EU countries is available ENT PIN code Pin s ENT via Menu ET Arming All partitions Ex PIN ENT LCD indication Arming mode Stay AA This arming m
9. ns System compliance and warranty The system is made in Lithuania warranty term is 24 months The manufacturer company Kodinis Raktas declares that product SECOLink complies with essential EU directive and EU standard EN 50131 1 See manufacturer s web site www kodinis It for complete text of declaration 2012 Kodinis Raktas
10. ode is used to protect a house when we are staying at home inside and are waiting that 8 somebody can come in Interior zones aren t protected After opening the door willbe entry delay Arming F key for EU countries 49 42 ENT in ENT for non EU countries is available ENT Via Menu T Arming EMD CSCS Stay PIN in Ent Parts EnD LCD indication AANS Arming mode Max Away AAA This arming mode is used when we are leaving the premise for a long period e g vacations After arming LI FP allzones will be protected entry delay is off alarm willsound uponopening door Arming F key PIN PiN ENT Via Menu ET Arming ED GS Max Away 8 PIN Cm n Parts END LCD indication Forced Arming F AAAA Z SE The arming mode that allows to arm the system when the zones are violated or the sensor is broken All Ll d sensors which were remained earlier will be armed After opening the entry exit door the system will give entry delay time Arming LCD indication F key for EU countries F gt ENT Pin Ent for non EU countries is available CF EN Via Menu ENT Arming EM C CHC Forced Arming E PIN PN Ent SECOLink MAS 800 KM20B KM20BT KM20GT keypad Intruder alarm system Short user manual Arming mode Night C This arming mode is used when you want to
11. onds during this time is possible to make usual arming procedure alarm trouble SECOLink MAS 800 KM20B KM20BT KM20GT keypad Intruder alarm system Short user manual Emergency keys In order to call for a help the premises must be secured by CMS press at once two specific keys and hold them at least 1 second When emergency alarm occurs siren starts to sound and alarm message will be shown on the keypad display Fire alarm A 01 Medical alarm 84 64 Panic alarm 7 Ways of disarming Disarming can be done by three ways F key entering PIN code Via Main Menu Using F key or entering PIN all partitions which are controlled by User will be disarmed After disarming via Menu it s necessary to unmark the partition which we don t want to protect The partition which will be disarmed is denoted the Jor keys and this action is confirmed by pressing the key AANS Disarming by PIN code when entering the premise After opening the door which are protected the system begins to count the entry delay During this time it is A necessary to enter PIN code and confirm by pressing the key All partitions which are controlled by User will be disarmed Pion Disarming by PIN code when staying in protected premise When all partitions are armed and the entry door weren t opened after entering PIN all partitions which are controlled by User willbe disarmed Disarmin
12. recommended to change default PIN F key CF 2 JEN Change PIN Cm ET New PIN Cn ET Repeat PinJ ENT Changed Via Menu ENT 4 4 4 4 Options EN Users END NT Change PIN iv Ent New PIN Pin s ENT Repeat PiN EnT Changed The example The User of the system has a PIN 1234 When he feels that PIN isn t secure he can change it by pressing sequence of keys F 2 0 Nt Change PIN 1234 Ext New PIN 3762 En Repeat 3762 Changed Keypad display and keys backlight changing F10 User has possibility to change contrast and backlight intensity of keypad LCD display also he can select conditions when keypad keys will be illuminated Default settings button s illuminating starts up after pressing the button or when occurs entry delay or alarm trigger For illuminating buttons all the time it is necessary to perform such actions F key CF J C0 Nt Keypad Settings Pin Ent Light ED C gt LCD amp keypad E Changed Cur CLR Via Menu EN 4 lt 4 4 4 Options EN Keypad settings END PIN Gin Ent Light END LCD amp keypad ENT Changed CR cCLR CLR Chime mode Chime function is used to inform User with the sound or light signal LCD display keypad keys about opening of entry exit door or violation of other selected zone From which zone chime will be activated you can set by pr
13. wly LCD indication 1 example ENT Arming NT 4 Max Away EnD PIN Pit Ent Parts 4 C gt C4 En W 2 example ENT Arming gt Away Nt PIN ine Ent Parts 4 C gt Ent 1 example 2 example Arming and disarming of security barrier Pre alarm mode Microwave or infrared rays based security barriers also outdoor PIR detectors which are connected to the system can be armed by Pre alarm mode The system will sound an alarm without sending alarm message to Central Monitoring Station when someone travers this electrical barrier The Pre alarm LOD indication mode can be turned on and turned off the same way as described below For the more convenient control of Pre alarm is recommended to create special F keys during installation process Via Menu gt C gt Prealarm PIN CN EN Parts C gt C E gt Bypassing zone B Bypassing a zone allows you to leave a door or window open while still arming the rest of your security system Bypass procedure can be made F key Be ENT PIN Pinse ENT Via Menu En gt gt C gt C gt Zone Bypass ENT PIN Pm Ent Zone isn t violated Zone is violated Zone is bypassed temporary Zone is bypassed permanently There are two different bypass type temporal or permanent First is used for one arming and disarming cycle second until the user unbypass the
Download Pdf Manuals
Related Search