Anypos200 User Manual
Contents
1. Anypos200 User Manual AOPOS SYSTEMS S A Anypos Point of Service Welcome Thank you for purchasing our powerful Anypos With this Guide is to help you operate the Anypos About the Product Anypos is an innovational design from Point of Sale terminals and Kiosk with over decade of market experience and product development capability A full range of functions are designed developed and produced to meet the requirements of department store supermarket hypermarket convenient store boutique shops restaurants theaters railway metro school and government projects hecking th kaging li After you unpack the Anypos check that the following items are included If any item is missing or appears damaged contact your dealer immediately le Es A Qy i N I L W A N 77 l K A E D User s manual Power cord cD Anypos Point of Service Identifvin mponen This section describes the parts and connectors on the Anypos Front view DESCRIPTION 1 15 inch TFT LCD and Touch screen 2 Magnet Stripe Reader Option 3 Power LED 4 HDD LED 5 IC Card LED Option 6 Power botton 7 Front Line out jack Option 8 Speaker Option 9 RF card reader antenna Option NOTE When you use front Line Out jack no voise will be out from the speakers Anypos Point of Service Rear view DESCRIPTION Bottom Panel Ports b mi Tw gt q ate lt gira We aedd Custdisplay2. the touchscreen was mapped to area for this touch system to guide the user do 4 points calibration User should follows the guide to touch and hold the blinking X symbol in the calibration window until it does not blink to make sure that the utility can gather enough data for computation Anypos Point of Service Clear and Calibration Press this button to erase the 25 points calibration linearization parameters and force user to do 4 points calibration again After 25 points calibration data was clear the 4 points calibration data will be invalid It needs to do 4 points calibration Linearization Linearization 25 or 9 points calibration function is used to compensate the touchscreen linearity After linearization completed the linearity of the touchscreen will be shown in the Linearity curve window Pressing this button a new window will be popped up at the location when the touchscreen was mapped to area for this touch system to guide the user do 25 points calibration User should follows the guide to touch and hold the blinking X symbol in the calibration window until it does not blink to make sure that the utility can gather enough data for computation x x x x x X x X x x x x x X X X x x x x X x x x X Anypos Point of Service Draw Test This function is used for accuracy and performance check Press this button and a new pop up window will be popped up in the location where the touchscreen was mapped to the touch syst
3. Adapter Mouse Printer Ethernet Sound Box Output a ao Lean Ti a ll CX Ki H AAN A 8669666066666 5 Pah CER lal e 207 Li Oto raro fl th ER th fi f COMH 12 n a e ml fa T COMI COM in v riia i 1 __ fa oo A saa e XV Fi Y f N ev y F S EA aa PIC 4 li 6 h a A a aaoo L E pape 1 A Dora a le j fe L aea O CH agate age i G A AAA ya J if L PEDO AAA Keyboard Maindisplay USB Device Microphone Anypos Point of Service DESCRIPTION OO 3 PS2 mouse port Pio 5 VGA port 6 Tapes 7 10 100NICport a 8 Microphone 4 9 Lino H Attaching VED mer Displ 1 Connect the customer display through the cable to customer display port on the bottom panel Anypos Point of Service 2 Secure the display with four supplied screws Attaching the LCD mer Displ 1 Connect the LCD customer display to the VGA port and 12V output port separately through signal cable and power supply cable 2 Secure the display with four supplied screws Anypos Point of Service Powering the An nand off 1 Connect the power cable to an electrical outlet on the Anypos Connect the adapter to the AC adapter connector 2 Press the power button on the underside of the display panel The power LED turns on Power LED Power Button 3 There are 2 ways to turn off the Anypos 1 Click Start button and then Tu
4. em M1 COM4 Ring function sel r JP1 COM1 COM2 Ring function selector JP2 COM3 COM4 Ring function selector JPland JP2 enable you to choose between 5V and 12V on COM1 COM4 respectively Since pin 9 on COM1 COM4 is reserved for switching between 5V and 12V Description Setting default 1 3 amp 2 4 5V Select 5V 1 TRT 3 5 amp 4 6 12V 7 9 amp 8 10 RI Tr leshottin Often after time spent troubleshooting the problem 1s traced to something as simple as a loose connection Check the following before proceeding to the problem specific solutions PROBLEM SOLUTION Make sure that the Power LED is on and Anypos is not in suspend mode and adjust the display brightness The display screen is The following message appears at boot up Ensure that an operating system is installed Invalid system disk Check the boot sequence in the BIOS setup eplace the disk and utility hen press any key Reboot the terminal and run the BIOS Setup An unidentified tility Confirm the Setup Utility parameters message 1s displayed If the same message is displayed after booting p again You cannot turn on the Check the AC adapter connection Make sure Anypos Point of Service erminal hat the adapter LED is on Otherwise replace he adapter Check the scanner cable connection Check The scanner is not he scanner with another terminal to see if it orking orks If the same problem occurs replace the Check that
5. rn Off Computer next Close 2 Use the main power button to turn off the power for example if the operating system you are using does not support power down by the OS or 1f the system crashes or hangs Recommended turning off 1 he T hscreen The touchscreen must be calibrated before in use After successful installation of diver the following icons will appear on your desk SS SAB os Anypos Point of Service Click on the General Touch Touchscreen the system will enter calibration interface E Touchkit USB Controller xj Edge Compensation Hardware About General Tools Setting Display Linearization Curve 4 Points Do4 points alignment to match display Calibration Clear and Clear linearization parameter and do 4 points Calibrate alignment fain Do 2 points linearization for better touchscreen Linearization linearity Do draw test to verify the touch accuracy Draw Test OF Cancel Calibration draw test tools and the linearity curve of the touchscreen were list in this property page shown as below for user to do touchscreen calibration and touch position test User can do calibration or draw test by pressing the function push buttons Linearization Curve Linearization curve of the touchscreen is list in this page for reference and trouble shooting purpose 4 points calibration Pressing this button a new window will be popped up at the location when
6. the power cord is plugged into a The screen is blank and working electrical outlet Check that the you don t hear any beeps Only the cursor appears Reinstall the operating system and power on he Anypos Ensure the audio cable is not defective The Audio problems mute is off Terminal is not working at all Wait 30 seconds and try again If still not working Reboot the terminal Otherwise have the Anypos serviced Wait 30 seconds and try again If still not working Reboot the terminal Otherwise have the Anypos serviced Terminal is frozen Having the An rvi If you are unable to solve the problem you should have the Anypos serviced Pack the Anypos in the original carton Include a description of the problem and a checklist of the steps you took when trying to fix the problem The information may be useful to the service personnel Return the Anypos to the place you purchased it 10
Download Pdf Manuals
Related Search