JA-82Y - GSM communicator
Contents
1. Owing to the above facts using pre paid SIM cards is not recommended 8 Remote control via a telephone keypad If you want to operate the alarm system via a phone mobile or landline perform the following JA 82Y user manual 5 MLD51300 Dial the GSM communicator number The system will answer in 15 seconds Listen to the voice menu introduction the system asks you to key in your access code On your phone keypad enter a valid access code user master or service code Listen to the answer current system state and the system offers to change its status You can press 9 to open keypad simulation mode switching back to voice menu mode is not possible dial again From this moment on the telephone keypad will work as a system keypad System status is signalled in these ways o 1 armed 2beeps unset disarmed programming mode sirensound alarm voice message during a type of event intruder alarm tamper alarm fault Any subsequent change to the system status is again indicated acoustically For instance after unsetting the system you will hear two beeps see above You can operate devices X or Y via the phone keypad the same way as from a system keypad This means 81 80 will control device X and 91 90 will control device Y To terminate the connection simply hang up Connection is automatically terminated if there is no entry within 60 seconds Note Remote access from2. a landline is only possible from a phone using tone dialling DTMF 9 Remote control by dialling in With some limitations the communicator allows you to operate the system by ringing the communicator This operation requires your phone number to have been pre authorized by being stored in the communicator memory Notes Dialling in operation is not enabled for phones having hidden numbers If you control by dialling in without remote access privileges the system performs the command and establishes the connection it s for free A phone which is pre authorized for dialling in remote control can also by used for normal remote control just let it ring until the control panel answers the call by voice menu Naturally a pre programmed function will be performed first JA 82Y user manual 6 MLD51300 10 Voice menu flowchart Incoming call Welcome to OASIS Enter your access code Entering SC MC UC Invalid Action impossible Enter your access code Rejected after 3 wrong attempts Armed system Disarmed system Press 2 to disarm Press 1 to armOK The 9 key pressed OK Disarmed Armed system system Keypad simulation If the system is in the requested state terminate the call Tab 1 JA 82Y user manual 7 MLD51300 Programming in maintenance mode Programming in maintenance mode requires access to be enabled by a service technician Other
3. is dialled only once regardless of whether the call is answered or not Calling the next telephone number can be stopped by pressing on your mobile phone Calling the next numbers are then cancelled and your phone keypad is switched to alarm keypad simulation Now you can remotely control the system like you are standing next to it If an alarm is cancelled by a user by presenting a valid code card while it is being reported any unsent SMSes and unperformed call reports are cancelled However the ARC still gets a complete set of reports about events in the system JA 82Y user manual 2 MLD51300 Remote control by phone For a mobile phone there are two ways to control the system remotely You can either send SMS instructions or establish an authorized connection protected by an access code to the system In this case the system is controlled by a voice menu Press 9 to switch the phone to alarm keypad simulation The phone keypad can be used the same way as the system keypad Using a fixed line phone you can only operate the system by dialling the communicator s number and establishing an authorized connection The below described way of remote control corresponds to the communicator s factory default setting The configuration can be modified during installation The installer should clearly explain any changes to the default setting 1 General rules for remote control via SMS instructions e than one instructi
4. Contents USER FEATURES 2 CAN REMOTE CONTROL BE SECURE seseessssccececssssosececeesscssocececeessoseoeceesessoseceese 2 HOW THE SYSTEM WORKS cssscccsssscccssssccccssscccssssccccsssccecssccccesacceessneececssseeessnaes 2 REMOTE CONTROL BY PHONE u csccccsssssccsssssecsssscccsssccssssccccsssacccessseccscssscecssnses 3 1 GENERAL RULES FOR REMOTE CONTROL VIA SMS INSTRUCTIONS 3 2 SETTING ARMING BY SMS H 3 3 UNSETTING DISARMING BY SMS 54 XXXX_UNSET 4 4 STATUS INTERROGATION STATUS 4 5 LAST EVENT INTERROGATION MEMORY cccccsessscecececsessceceeececsessnsseeeeeeees 4 6 CONTROLLING APPLIANCES BY SMS 4 u cccccscssssccccecsesscsscecececsesseceeceecsenseeeeeeeees 5 7 SIM CARD CREDIT INTERROGATION amp _ 5 8 REMOTE CONTROL VIA A TELEPHONE 5 9 REMOTE CONTROL BY DIALLING IN ccccccccccecsssssseceeececeesseaececececeessaaseeecesesensaseeeceeees 6 10 VOICE MENU FLOWCHART 7 PROGRAMMING IN MAINTENANCE MODE ccssccccssssecssssccccssssccecsccsessssceessnse 8 REMOTE ACCESS BY INTERNET uuu cesssscccsssccssssccccssssccecssccecsssaccsessccccecscceessnses 8 JA 82Y us
5. ding 4321 SET will set the system the same way as if the code 4321 had been entered on the system keypad Notes As a factory default setting arming by a SET instruction is confirmed by the system via an SMS reply e When the current system status does not allow system operation e g when in programming mode you will be notified about the situation via an SMS reply e Ina split system an xxxx_SET instruction will only have an effect on the section to which the code belongs JA 82Y user manual 3 MLD51300 3 Unsetting disarming by SMS xxxx_UNSET The UNSET instruction allows you to unset disarm the system fully or partially If the system is already unset it will not change its status Send an SMS message containing xxxx_UNSET where XXxx is a valid access code user or master is a space character Example Sending 4321 UNSET will unset the system the same way as if the code 4321 had been entered on the system keypad Notes e As a factory default unsetting disarming by an UNSET instruction is confirmed by the system via an SMS reply e When the current system status does not allow system operation e g when in programming mode you will be notified about the situation via an SMS reply e split system an xxxx_UNSET instruction will only have an effect on the section to which the code xxxx belongs 4 Status interrogation 0 xxxx_STATUS The STATUS instruction allows you to get informatio
6. er manual 1 MLD51300 User features The JA 82Y GSM communicator offers many useful features Its main purpose is reporting events directly to you and to an ARC Alarm Receiving Centre In addition the communicator allows you remote system control and programming by phone or Internet and the remote control of appliances in a house e g heating Can remote control be secure There are several mechanisms for protection to ensure that remote system control is secure Using a phone The communicator s SIM card number gives basic protection This number is not explicitly referenced anywhere in the system and we recommend keeping it private As a second level of protection every SMS instruction is required to contain a valid access code the same code as the one used for system operation from the keypad This code is also used when you request system access via a phone call for so called connection authorization The third level can be realised by naming instructions with your own texts We recommend recording these texts and keeping them in a safe place How the system works Alarm triggering is processed by the communicator as follows If enabled reporting to ARCs Alarm Receiving Centres is started first SMS reports are sent to pre programmed phone numbers in the order they are stored As a sort of acoustic signalling pre programmed phone numbers are called again in the order that they are stored Each phone number
7. n about the current system status The communicator will reply with an SMS reporting the current set unset status GSM signal strength GPRS connection status and transmission success failure status for each ARC involved Send an SMS message containing xxxx_STATUS where is a valid access code user or master is a space character Example If the system is set an SMS instruction 4321 STATUS will be replied by the system via an SMS message which might look like the following Report from your alarm System status Set GSM 80 GPRS OK MS1 OK MS2 OK MS3 OK where GSM 80 means the GSM signal strength GPRS OK means communication via GPRS has been successfully established and MS1 OK MS2 OK MS3 OK means that all relevant data has been transmitted to monitoring stations MS1 MS2 and MS3 5 Last event interrogation 50 xxxx_MEMORY On receiving a MEMORY instruction the communicator will reply by reporting the last 3 events recorded in the control panel memory Send SMS message containing xxxx_MEMORY where XXxx is a valid access code user or master is a space character JA 82Y user manual 4 MLD51300 Example If an alarm has been triggered the communicator will reply to the SMS instruction 4321 MEMORY by reporting Report from your alarm Last events Unsetting Master code Alarm cancelled by user Master code Delayed alarm 02 Device 6 Controlling appliances by SMS x You can send SMS instructio
8. ns to switch on off communicator or control panel outputs Up to 2 appliances can be attached device X and device Y see the corresponding table in the control panel user manual The communicator will reply with an SMS message to confirm performance of the instruction To switch device X on send the following SMS _ _ To switch device X off send the following SMS To switch device Y on send following SMS Xxxx_PGY_ON To switch device Y off send the following SMS Xxxx_PGY_OFF where XXxx is a valid access code user or master is a space character Example If the heating in your house is operated as the X device you can switch the heating on by sending xxxx PGX ON 7 SIM card credit interrogation 54 xxxx_CREDIT If a prepaid SIM card is used in the communicator you can check the credit balance Send an SMS message containing xxxx_CREDIT where XxXxx is a valid access code user or master is a space character Example The xxxx_CREDIT request is responded to by the following message Report from your alarm Credit Current balance is 26 35 Notes e This instruction has to be pre configured by the installer according to GSM provider requirements e user is responsible for the credit balance being sufficient e The GSM provider may have a time limit after which the credit validity will expire e You can find more details on this function in the communicator installation manual
9. nsfer Remote access is provided by Jablotron Alarms free of charge only the data transfer from the premises is charged The installation technician can set up remote access according to the desired arrangement Accessing the communicator remotely requires its SIM card to be enabled for GPRS data transfer Only then can the device work properly You can operate the system directly using a virtual keypad by entering a programming sequence Olink can open a command line where the sequences can be entered the same way as if they were entered from a system keypad By pressing the submit button you send the instruction via the internet network to the communicator where it will be processed More details with descriptions can be found in the installation manual The list of events can be opened in any control panel state therefore it is not necessary to put the control panel into a specific mode like unsetting or switching to Maintenance Mode The events list records the last 255 events JA 82Y user manual 8 MLD51300
10. on can be used a single SMS message It has to be separated by a comma SMS instructions are not case sensitive Only standard English ASCI characters are accepted e All SMS instruction words parameters must be separated by a space In this document a space in SMS instruction will also be denoted by the underline character e SMS instructions can be sent from a mobile phone or from a GSM gateway e Ifthe character is used all preceding text will be ignored The symbol ends processing when used in SMS text i e all the following text will be ignored It is recommended to use this symbol at the end of the instruction if the provider sends some additional text after your message advertisements etc e Warning If any extra text is not separated from a valid SMS instruction text by or symbols the SMS message will not be recognized and no instruction will be executed e Performance of the instruction is confirmed by an SMS reply e default instruction texts can be customized by an installer or administrator E g the command PGX ON can be changed to SWITCH ON HEATING etc 2 Setting arming by SMS xxxx_SET The SET instruction allows you to put the system in to a set armed state fully or partially If the system is already set it will not change its status Send an SMS message containing _ where XXxx is a valid access code user or master is a space character Example Sen
11. wise no programming is possible any instruction sequence will be rejected by the system and the keypad will beep four times The following description is intended for a system administrator who knows the control panel master code All the settings can be performed via keying in on a system keypad An unfinished sequence can be cancelled by pressing the key A sequence is only stored in control panel memory or executed after the sequence has been completely entered All the settings are only applicable if the control panel is in maintenance mode To enter maintenance mode first make sure that the system is completely unset Then enter the following sequence on the system keypad 0 master code card The keypad will display Maintenance mode In maintenance mode it is possible to set transmission parameters measure the GSM signal strength enable disable remote access set the forwarding of incoming messages record voice messages and so on More details with descriptions can be found in the installation manual Wrongly set parameters could limit or cancel some of the functions alarm reporting faults When you change any parameters test that the system works properly Remote access by Internet The system can be accessed remotely via Olink software version 2 0 and higher which allows complete programming by installers and also operating the system by end users The GPRS service or alternatively SMS is used for data tra
Download Pdf Manuals
Related Search