Barudan BESR User Manual
Contents
1. Barudan BESR User Manual Instructions Basics Control Panel Keys e PRODUCT Shows stitch counter Is reset by pressing and simultaneously e FUNC Edits function codes of a design in memory e AND KEYS To increment or decrement parameters e TEACH G To program the color change sequence e TS Activates thread trimming at color change or stop codes Toggles on and off e SCALE Resizing of the design Use the and keys e ROTATION Rotation of the design Use the and keys e MIRROR Quick mirror of the design Toggles on or off e TAPE To bypass memory and sew one stitch at a time from tape e NEW To store a design in memory e ADD To add to a design in memory e KEY To delete a design SET To accept a parameter MENU KEY 1 LEFT To change the current design number MENU KEY 2 MIDDLE To change the tape code e MENU KEY 3 RIGHT To rotate design by 45 degrees e O KEY To change between absolute or incremental frame movement information e ORIGIN Hold down shortly to cause frame to seek origin point of design e FLOAT When toggled on the design will move through the design without sewing DRIVE Activates and de activates DRIVE mode Press to activate hold down to de activate Parameter setting PARAMETERS Hold down the O KEY for one second to enter parameter settings Use the keys and the O KEY to configure machine Bar switch and button under table e BAR SWI2. TCH LEFT Pull bar to the left to stop sewing BAR SWITCH RIGHT Pull bar to the right to start sewing Frame move e ARROW KEYS To manually move the pantograph Load a new design Loading from the Tape Reader or USB Reader 1 Be sure you are not in DRIVE mode If the DRIVE light is on then hold down DRIVE until stops beeping 2 Press the NEW key 3 Press MENU KEY 2 on the upper middle until the menu says U 4 Press MENU KEY 1 on the left until you have chosen the memory location to store in 5 Press the DRIVE key The download will start 6 Finished Select a design in memory 1 Be sure you are not in DRIVE mode If the DRIVE light is on then hold down DRIVE until stops beeping 2 Press MENU KEY 1 on the upper left until you have picked a new design 3 Move the pantograph to your design start location 4 Press the DRIVE key 5 Pull the bar switch to the right You should hear a beep 6 Done Setting color change 1 Be sure you are not in DRIVE mode If the DRIVE light is on then hold down DRIVE until stops beeping 2 Switch to the design you wish to program color change for by pressing MENU KEY 1 3 Make sure the TEACH button is OFF If the light is on press button to turn it off 4 Hold down TEACH button until it starts flashing and beeping continuously 5 Press DRIVE button 6 The display will scroll to the next color Use the and keys to change to the desired needle n
3. ull delete some designs E9 DESIGN REFUSED Reload the design or delete a design from memory E10 SLIDER INACTIVE One of the hook grabbers underneath the head is stuck or not at its sensor home position If unable to control pantogram then check your J2 J3 J4 boards with power off Also check the chunky bar transistor which is to the right of the J4 slot Contact our repair department if you suspect damage
4. umber 7 Press DRIVE to set the color and repeat until the end of the design 8 There is not usually a color change at the beginning so set the color manually before sewing Erasing design in memory 1 Be sure you are not in DRIVE mode If the DRIVE light is on then hold down DRIVE until stops beeping 2 Press the KEY 3 You will see on option for Thread Trim and for DELETE 4 Choose the DELETE option by pressing MENU KEY 3 on the upper right 5 You will now be at a delete menu 6 Press the and keys to select the design to erase 7 Press the SET key to delete the design Immediate thread trimming 1 Be sure you are not in DRIVE mode If the DRIVE light is on then hold down DRIVE until stops beeping 2 Press the KEY 3 You will see on option for Thread Trim and for DELETE 4 Choose the THREAD TRIM option by pressing MENU KEY 2 on the upper middle 5 The display will show BAR START 6 Pull the underneath bar to the right to activate immediate thread trim Error codes e E2 MANUAL SW For roll to roll operation E3 UNLOCK When color change turret is off position Check if the pin is in the V shaped groove on the heads E4 READER The tape reader is not seen ES TAPE ERROR When tape reader data is incorrect E6 NO DESIGN When a memory location with no design loaded is chosen E7 MEMORY ERROR This memory location has been deleted ES FULL DELETE The memory is f
Download Pdf Manuals
Related Search