User Manual - Nexus Metal Detectors
Contents
1. Located under the control box and accessible from the hand grip this toggle switch is used to change operating modes When pushed to the left the Nexus Standard Mk II operates in Discrimination Mode In the centre position the Nexus Standard Mk II operates in All Metal Mode If pushed to the righ the switch will enable the Turbo Audio mode In Turbo Audio Mode the Threshold level have to be readjusted for best detection without false signals In Turbo Audio all signals are with the same audio level deep and shallow alike Standard Motion Silent Motion Battery Test Toggle Switch This is located on the front panel of the control box It is used to check the condition of the batteries by using the DDM if the meter bar lights one third or less of its length changing or recharging the batteries is recommended The other positions for this switch toggles the Nexus Standard Mk II between Tone and Silent search modes This toggle switch also controls the change from Standard Motion of detecting to the Silent Motion filter Recovery Toggle Switch This is located on the front panel of the control box It is used to control the recovery or reset speed of the detector for Slow Middle and Fast reset A slow recovery is best for sites with few signals and a fast recovery for sites with many signals or contamination General Operation and Setting Up Having assembled the Nexus inserted batteries and connected the headphones The Nexus is ready fo2. results in the hands of every user regardless of their experience with metal detectors With the Nexus Standard Mk II everyone can enjoy the benefits of the deep seeking Nexus technology both novice and professional alike As a general rule the best results will always be obtained when the Nexus Standard Mk II is properly set in manual mode Therefore users will need to practice and experiment in order to obtain the best possible results on any particular site All sites and soils are different and settings that will give good results on one site may be less successful if used elsewhere The Nexus Standard Mk II is designed to detect the very deepest of targets and operates near to the limits of what is achievable with induction balance Assembly amp Preparation The Nexus Standard Mk II is supplied boxed and ready for quick assembly by simply attaching the two lower stem poles to the top one tightening the collars and attaching the coil to the lower stem section using the plastic bolt and friction washers supplied and tightened by hand so that coil is held at the correct angle to the stem the coil cable plug is inserted to the socket in the control box and then tighten the knurled ring taking care when winding the cable around the stem that the cable is not strained The centre stem pole is of the same tube diameter as the top one and can be left off in circumstances where a short stem is needed it is meant for use on steep sites river ba
3. FALSE SIGNALS FROM THE GROUND MINERALS To achieve the best ground balance tuning it is essential that the coil be held parallel to the ground surface at all times during the procedure The next setting is to adjust the Sensitivity to suit the site conditions From the minimum setting of the Sensitivity knob set at minimum in the initial ground balancing procedure adjust the control clockwise to increase the 11 sensitivity Repeat the procedure of raising and lowering the coil between 3 75 mm and 10 250 mm above the ground surface as for ground balancing If there is no change in tone while doing this then the sensitivity may be increased further For best results the setting should be at the maximum possible while maintaining a stable threshold tone At maximum sensitivity settings a slight tone change may be noted when both raising and lowering the coil This will not adversely affect the operation of the Nexus Standard Mk II providing that the coil is kept at a reasonably constant level above the ground surface and parallel to it while detecting Setting the desired Discrimination level is done by rotating the Discrimination knob clockwise to INCREASE the discrimination level and REDUCE the sensitivity to ferrous iron higher than necessary settings will result in desired targets being missed Rotating the Discrimination knob anticlockwise will DECREASE the discrimination level and INCREASE the sensitivity to ferr
4. achievable dept on small medium and large targets in all conditions With the previous Nexus Standard SE this coil design was capable to detect small 18mm coin up to 40 cm under ground and 30mm coin up to 48 cm under ground The extend of the detection dept with Nexus Standard MkII have not been fully tested classic dual 6 at 5 2kHz High Energy For maximum dept of small and medium targets in mineralised conditions and contaminated sites Also very good for general search classic dual 6 at 8 5kHz High Energy Best for general search in all conditions Good for all targets It detects 30mm coin at 40 cm under ground in real search conditions classic dual 6 at 18 kHz High Energy Best for small targets gold nuggets and gold coins classic dual 4 at 7 3kHz High Energy Specially designed for contaminated areas with best possible dept for small and medium targets It detects a small 18mm coin at 28 cm and 30mm coin at 36 cm in real search under ground Very good for checking holes and ditches classic dual 4 at 15 kHz High Energy The ultimate gold nugget hunter It can detect gold nuggets as small as 10 milligrams DD shape search coil range 13 DD at 6kHz High Energy General search coil designed for higher detection ratio of small medium and large targets in normal search conditions It exhibits greater depth than any other DD search coil made by other competitive brands It detects 18mm coin at 28 cm with
5. knob from approximately middle position in anti clockwise direction slowly and while swinging over the target until the audio signal reduces to clicks The Nexus Standard Mk II is now able to work effectively in fields loaded with hot rocks or metallic ore pieces Discriminating Against Salt Water on wet sand or tidal beaches The procedure is very similar to that used for hot rocks and minerals After initial set up begin turning the Discrimination knob from position 0 to clockwise direction very slowly until the salt water signals turn into small clicks Keep the Ground Balance know in position where the ground minerals are usually cancelled balanced out Discriminating Against Large Metal Objects leaving only the smaller ones and Special Gold Nugget hunting setting There are some conditions where only small targets are required in a particular search desirable targets such as gold nuggets or tiny coins These are especially difficult to search for in contaminated conditions or in the presence of mineralised soils To remove all large targets and leave only the desired very small objects make sure that the Discrimination level is set to allow your desired small targets to be in the range of good non ferrous targets Turn on the Iron Rejection Mode using the toggle switch under the control box this switch is moved to the LEFT 14 Begin swinging the coil over any target that you wish to remove from the audio responses Wh
6. knob from position 0 towards position 10 clockwise Keep doing so until all small targets are giving small clicks in the audio responses and also not giving a response on the DDM meter Now the Nexus Standard Mk II is ready for hunting larger objects only Note During this procedure discriminating hot rocks and or metallic ore may not be possible or with great limitations Using a considerable level of discrimination against hot rocks and or metallic ore during this procedure will result in detecting only medium size targets The best way to get rid of all small objects while using the Nexus Standard MkII is by far the Silent Motion filter Silent Motion setting can be used when the detector is set in Auto mode or Manual mode 15 To reject most undesired small and medium objects turn the Auto function on Then choose Silent Motion from the relevant toggle switch on the front panel In this setting and while conducting a normal sweep speed the detector will be silent to all ground minerals all small and medium Iron targets and to all small to medium non ferrous targets Only considerable in size non ferrous and Iron objects will be detectable If the sweep speed is considerably reduced while using this setting the detector will start detecting medium targets and coins but not small and medium Iron If Silent Motion is used in Manual detector settings that will allow the complete rejection of all small and medium targets To achieve th
7. very loud signal responses Due to large search area it will find more targets for shorter period of time compared to smaller search coils Not suitable for mineralised conditions due to high probability of producing multiple signal responses Extend of detection dept not fully tested yet 10 DD at 7kHz High Energy It could be the best general search coil that you ll ever need It exhibits excellent dept and discrimination in most conditions Very efficient in detecting small targets at great dept Very fast in isolating individual targets It detects 18mm coin at 28cm with very good signal response Extend of detection dept not fully tested yet 10 DD at 18kHz High Energy Specially designed for gold nuggets and small targets at great dept Extend of detection dept not fully tested yet 7 DD at 8kHz High Energy General search coil designed for quick scan of new detecting fields and areas Very good for searching narrow spaces holes and ditches Best suited for small and medium targets in contaminated areas Each coil is tuned to a slightly different frequency within the design range to minimise interference from other Nexus detectors Performance values for all Nexus detectors will be identical To obtain the best results with the Nexus Standard Mk II as with all metal detectors it is essential to understand the settings and operation of the detector The Auto mode of the Nexus Standard Mk II will provide exceptional quality
8. Nexus Standard Mk II metal detector User Manual Table of contents OND ve General description page 3 4 5 6 Assembly amp Preparation page 6 7 Controls page 7 8 9 DDM Definite Discrimination LED Meter page 8 Discrimination Control page 8 Ground Balance Control page 8 Threshold and Auto Mode Control page 8 Sensitivity Control page 8 Volume Control and Power On Off switch page 9 Multi Tone Control page 9 Mode Iron Rejection toggle switch page 9 Silent Motion Standard Motion and Battery Test toggle switch page 9 Recovery Mode toggle switch page 9 Operation page 9 10 11 12 If you are a novice in the hobby or a child page 9 10 If you have some experience but still not on a professional level page 10 If you are a professional or have extensive experience with metal detectors page 10 Full Manual Set Up page 10 11 12 Search method page 12 All Metal Mode page 13 Discrimination Mode page 13 Pinpointing page 13 Special Modes of operation page 13 14 15 16 Discriminating Ground Minerals in severe mineral conditions page 13 Discriminating all types of hot rocks and metallic ore page 13 14 Discriminating salt water on tidal beaches and salt water lakes page 14 Discriminating all large metal objects leaving only the Smaller ones Special gold nugget hunting tune page 14 15 Discriminat
9. at enables the Auto function When the Threshold knob is turned fully anti clock wise the switch will click and the Auto function will automatically set base levels for the Threshold Discrimination Ground Balance and Iron Rejection controls those controls will not work manually unless the Auto Mode is turned off from the Threshold knob In Auto mode the Sensitivity level is recommended to be set to minimum Once the Auto function is turned on three LED lights will indicate that Ground balance Discrimination and Threshold are automatically controlled Sensitivity This knob controls the level of sensitivity of the responses The sensitivity level setting chosen will depend on the soil conditions but in general the highest possible setting should be used On contaminated or mineralised sites it may be necessary to reduce the sensitivity to avoid some false signals Volume and Power On Off switch This knob sets the volume of the tone and responses and it is used also to turn on off the Nexus Standard Mk Il This knob should always be used for setting the volume Any volume control on the headphones should be set to MAXIMUM When the Power is turned on an LED light above the Volume control knob will indicate that detector is turned on Multitone This knob activates and adjusts the audio discrimination option and gives a high pitched tone response for non ferrous and low pitched tone for ferrous iron responses Mode Toggle Switch
10. d performance Heavily furrowed broken ground or thick stubble are all especially difficult ground types to search Sites where the ground conditions vary to a considerable degree may require the Ground Balance to be adjusted from time to time for best results Care of the Nexus Standard Mk Il All metal detectors are precision instruments and require careful handling to ensure they remain in good working order Avoid dropping impacts or violent shaking of the detector and protect it while transporting The detector should not be used in extremely wet weather conditions without protecting the control box and the battery The coil assembly is fully waterproofed If water penetrates any of the boxes switch off the detector and remove the batteries It is suggested that the detector be placed in a warm place to dry out slowly Mud and soil should be carefully removed using a damp cloth or water only Do not use detergents or abrasives and avoid getting water in the control boxes When storing the detector for long periods or when shipping the batteries should be removed Avoid storing the detector in areas where it will be exposed to extreme temperatures dust moisture or contaminants Do not attempt to modify or repair the detector or allow any unauthorised repair centre to do so Guarantee The Nexus Standard Mkll metal detector is guaranteed for a period of 24 months from date of purchase against all manufacturing defects T
11. he Control Box is sealed and contains no user serviceable parts Opening the Control Box will invalidate the Guarantee 17 This Guarantee does not cover Damage due to dropping impact or accident Damage due to improper use or care of the detector Damage resulting from leakage of batteries Damage to the coil or coil cable In the event of any problem please contact us Any detector returned under Guarantee must be properly packed preferably in the box supplied and be sent by insured carrier The sender is responsible for any loss or damage in transit A full repair and replacement parts service is available Technical Specifications Operating Frequency Range 6 18kHz kHz Coil Design DD and Twin Concentric Overlapping Coil Weights Dual 9 or13 DD 650gr 10 DD 540g 6 450g 4 380gr 7 DD 350gr Weight main unit only 1 0 kg without batteries Coil Case Construction ABS plus Fibreglass Audio Frequency Custom tuned Audio Output 6mm stereo headphone jack Power Supply 15v 10 AA alkaline batteries Battery Life up to 10 hours Operating Modes All Metal Discriminate and Auto tune Optimum Temperature Range 15 to 60 C Optimum Humidity Range 0 to 85 RH Troubleshooting 1 The detector does not turn on Check the batteries If they are old replace them with new Make sure the batteries are properly inserted into the battery holder and have a good electrical contact 2 The detector is gi
12. ile swinging the coil start turning the Ground Balance knob anti clockwise position as slowly as possible Keep doing so until all large targets and minerals are removed and only the gold nuggets and smallest non ferrous objects are left for detection The Nexus Standard Mk II is now ready for hunting only those small targets Note Gold nuggets and all small targets are best detected at the standard ground balance setting in All Metal Mode This procedure is only recommended in severe contamination or bad mineral conditions As setting the detector in this way will result in a high discrimination setting while rejecting all large targets there will be also a loss of depth for the remaining small targets as much as 50 Discriminating Against Small Targets and leaving only larger metal objects Many treasure hunters have been looking for the perfect metal detector One of those aims is for a detector that is capable to ignore or not detect at all small metal objects such as coins bottle caps even ring pulls and detect only larger metal targets such as hoards metal pots helmets shields etc To reject all small metal targets after proper Ground balance is been done turn the Iron Rejection Mode on the Mode switch to the left Place on the ground surface samples of all small targets that you do not wish to be detected Start swinging the search coil closely over the unwanted targets While doing so start turning slowly the Discrimination
13. ing all small targets and leaving only larger metal objects page 15 16 Silent motion page 15 16 Tips page 16 17 Care of Nexus Standard MkIl page 17 Guarantee page 17 18 9 Technical specifications page 18 10 Troubleshooting page 18 General Description The Nexus Standard Mk II is an Analogue Induction Balance IB metal detector that operates in the very low frequency VLF range and it is designed for use on all Inland Sites and Tidal Salt Water Beaches It may be used in any of the three basic modes of operation Auto All Metal or Discriminate The Nexus Standard Mk II is designed to be a general purpose metal detector capable of finding both small and large targets at extreme depths The standard coil supplied is the classic dual 9 unit or the 13 DD and this is ideal for general searching operations There are 11 different search coils that can be used as accessory with the Nexus Standard MkII Classic number 8 shape search coils classic dual 20 SE Ultima search coil at 5 2kHz High Energy For maximum dept on medium and large metal targets in all conditions The most powerful hand held search coil in the world The full extend of the detecting capabilities with Nexus Standard MkIl is yet to be established Guaranteed detection dept on a metal helmet 2 meters under ground classic dual 9 at 6 8kHz High Energy Best for general search in all conditions Exhibits maximum
14. is level of rejection simply set the detector in manual mode with it s normal setting for ground search Then turn the Silent Motion filter on Get any small or and medium target that you wish to be completely rejected Begin swinging the target in immediate proximity to the search coil in all possible positions and very slowly While doing so start turning the Discrimination know from 0 to clockwise slowly until the tested target is no longer detected Tips The Nexus Standard Mk II may seem different in operation to some detectors presently available Some practice and experimentation with the settings is necessary to get the best results on different sites Users should persist and regular use over a reasonable period is likely to be needed to become proficient especially in successfully locating the very deepest and smallest of targets It must always be remembered that no detector can find what is not there nor can any detector give a signal unless the coil is passed directly over that target There will always be sites on which any single detector does not work to peak efficiency All detectors and sites are different and a particular combination of frequency and filtering might be best on a specific site although the range of accessory coils available for the Nexus Standard Mk 16 II will allow effective operation under almost all conditions and for all types of targets Site conditions will significantly affect depths an
15. k is been done turn the toggle switch back to Standard motion or Silent motion to allow the DDM to indicate metal targets Keeping the DDM in battery check mode for a long time will drain the batteries Holding the Nexus Standard Mk II with the coil well above ground level adjust the Sensitivity control knob to minimum Adjust the Threshold knob to obtain a minimal faint tone setting Adjust the Volume knob to seta comfortable level remembering to set any adjustable headphone volume control to MAXIMUM Lower the coil to the ground and sweep side to side slowly to ensure that there are no metal targets in the place you are tuning the detector When you are satisfied proceed as follows Position the coil about 3 above and parallel to the ground surface Raise the coil gently to about 10 250 mm above the ground and lower back to 3 75 mm above ground several times Note whether the threshold tone remains the same or if it increases or decreases in intensity while raising and lowering the coil If the tone rises when LOWERING the coil towards the ground then adjust the Ground Balance knob slightly in the clockwise direction If the tone rises when LIFTING the coil away from the ground then adjust the Ground Balance knob slightly in the anti clockwise direction Repeat this procedure to check and if the tone remains constant the ground balance is set properly IF THE GROUND BALANCE IS INCORRECTLY SET THE DDM METER WILL INDICATE STRONG
16. level Controls The Nexus Standard Mk II has six rotary control knobs and three toggle switches two located on the front panel of the control box and one underneath the control box NEXU scanoara MKII am BICOLOURED DDM If i d N o Kg 40 SENSITIVITY Ky MULTITONE DDM Definite Discrimination Meter The DDM meter is based on LED technology and provides a reliable visual discrimination analysis in All Metal Mode and Iron Rejection Mode The bar will light RED for non ferrous and BLUE for ferrous iron targets Discrimination This knob sets the level of the discrimination Rotating the Discrimination knob clockwise from 0 to 10 will INCREASE the level so that Iron is increasingly not detected but high settings will result in the loss of potentially good targets Generally the discrimination level should be set as low as is possible to avoid masking the smallest and deepest desired targets Ground Balance This knob is used to set the balance of the Nexus Standard Mk II to suit the soil conditions on any given site Threshold and Auto Mode This knob sets the level of the threshold tone The Nexus Standard Mk II may be operated in silent mode with no audible background tone or with this tone set to give a slight tone level In order to readily discern the faintest and smallest of signals operation with a slight background tone is recommended The Threshold control knob is combined with a switch th
17. move all interference chatter and electronic noise The detector stopped working during rain Nexus detectors are not water or weather proofed Knowing that we strongly recommend that no Nexus metal detector model is used in rain If this happens turn off the power of the detector from the Volume knob Take out the batteries and leave the detector near a warm place for a couple of days to dry out After that if still not working return the detector to your dealer for maintenance and repair 19 20
18. nded settings here will help to overcome the problem To cancel out the effect of Ground Minerals turn on the Iron Rejection Mode using the toggle switch under the control box this switch is moved to the LEFT Lower and raise the search coil over the ground surface as you would do in the standard Ground Balance procedure Begin turning the Ground Balance knob anti clockwise slowly while swinging the coil until the ground mineral signals reduce to small clicks Now the Nexus Standard Mk Il is ready to work in severe Ground Mineral conditions 13 Discriminating Against hot rocks and metallic ore In some instances the ground balance and or Discrimination settings may not be sufficient to remove the audio responses from some types of hot rocks or highly metallic ore pieces If this proves to be a nuisance while detecting the procedure required to remove the hot rocks and or metallic ores from the audio signals or at least to reduce their interference is similar to that used for Discriminating Ground Minerals To remove the hot rocks and or metallic ores from the audio signals turn on the Iron Rejection Mode using the toggle switch under the control box this switch is move to the LEFT Start swinging the search coil over a sample of the specific type of a hot rock or ore piece that you wish to be removed from the audio responses positioned as you would detect them during normal searching Begin turning the Ground Balance
19. nks caves ditches and similar conditions This configuration is also useful if the Nexus Standard Mk II is to be used by children and makes it a good family metal detector that can be used by anyone in the family The Nexus Standard Mk II is supplied with a drop in battery holder that can be used for all types of AA size batteries alkaline or rechargeable a charging socket is provided to the battery box for connecting a charger unit To insert or change batteries remove any three of the thumb plastic screws from the base lid of the battery box the battery box is below the arm cup at the top of the detector stem and loosen the fourth screw Turn the cover to the side Insert the 10 batteries in their correct alignments into the plastic holder and make sure that all the terminals have a good electrical contact Locate the battery holder into the compartment ensuring the connecting terminals of the battery holder are in good contact with the two electric spring loaded terminals behind the recharge socket Do not over tighten the plastic thumb screws when refitting If you wish to use headphones highly recommended connect your available set to the 6 mm jack socket on the battery box The Nexus Standard Mk II has an internal loudspeaker so headphones are not absolutely essential For any headphones that have a volume control ensure that this is set to MAXIMUM and use the Nexus Standard Mk II Volume knob on the control box to set the volume
20. ous iron targets In general an effective method of setting the Discrimination level suitable for most search conditions is by passing a rusty iron nail about 50mm long close to the search coil Rotate the Discrimination knob clockwise until the iron nail is rejected in every possible position against the coil After this procedure check if small non ferrous targets are detectable without loss of depth Finally check again the threshold and volume settings for comfortable levels The Nexus Standard Mk II is now set up for the particular site conditions and is ready for use Search Method With the Nexus Standard Mk II set up and ready the coil should be swung smoothly from side to side a little above the ground surface The sweep speed should be according to the Recovery settings It is not effective to scrub the coil on the surface of the ground this can also damage the coil and places strain on the stem assembly Suggested operating heights for the standard coils are Dual 9 coil 2 50 mm minimum above ground surface Dual 6 coil 1 25 mm minimum above ground surface Dual 4 coil Any distance 13 DD coil 2 50 mm minimum above ground surface 10 DD coil 1 40 mm minimum above ground surface 12 TCDD coil Any distance Make sure that the coil is swung evenly over and parallel to the ground surface and that the coil does not rise at each end of the swing Cover the ground in smoo
21. r use If you are a novice metal detector user Simply turn on the Auto Mode activated on the Threshold control knob on and start detecting With a little time and practice as you gain experience with the detector you can progress to Manual Modes already then having some idea of what most target responses will be like A minimum Sensitivity level is recommended in Auto Mode to minimise clicking or and possible false signals If you have some metal detector experience We recommend the Auto function above for at least the first couple of days If you have considerable experience with metal detectors No metal detector however powerful will operate at its best unless it is set up properly for the conditions in which it is to be used To obtain the best results and maximum depth and sensitivity to desired targets the Nexus Standard Mk II must be properly tuned to the site and the settings to achieve this are set out below Full Manual Set Up 10 Firstly ensure that no metal is in close proximity to the coil It is also advisable to carry out the tuning and setting up of the Nexus Standard Mk II away from other metal detectors or potential sources of electronic interference Turn the Nexus Standard Mk Il on A tone will be heard and the DDM meter will flash The tone will fade and the meter bar will settle after a few seconds To check the condition of the batteries turn up the Battery Check toggle switch After the battery chec
22. th parallel swings to ensure maximum detection coverage In All Metal Mode both ferrous and non ferrous targets will give the same audio response unless the Multitone function is turned on by a sudden increase in the intensity of the threshold tone A strong response indicates a large or relatively shallow target and a weak response indicates a small or deep target Any audio signal in All Metal Mode may be analysed by using the DDM meter To analyse a signal with the Meter observe its colour response In Discrimination Mode good non ferrous targets will give a clear well defined two way repeatable audio signal Ferrous targets will give a clicking audio response or an indistinct and erratic response Silent Motion is a very powerful discriminator that will stop all signal responses from Iron ground minerals how rocks and electrical interference Pinpointing is by simply X ing the coil across the signal The position where the signals are strongest below the coil centre indicates the target position As with all detectors when targets are of complex shape or are located at an angle in the soil pin pointing may not be entirely accurate so it is suggested that when digging the user allow space to avoid possible damage to finds Special Modes of operation Discriminating Against Ground Minerals in severe mineral conditions If normal Ground Balance proves to be ineffective in dealing with the Ground Minerals then the recomme
23. ving too many false signals If this happens first turn the Sensitivity to 0 minimum level Check the Ground Balance if it is adjusted correctly according to the ground balance procedure If the problem still persist check if the soil does not contain hot rocks or other contaminants If this is the case then use Silent Motion and or Iron Rejection to stop the interference Auto mode will also assist in such conditions 3 The detector is picking up too much Iron Check the Discrimination level according to the recommended settings or use Auto mode 18 I only plug the search coil and detector does not work after that Make sure that it is the correct search coil for your Nexus model The search coils for Nexus Standard MkIl are not interchangeable with the lower Nexus models and vice versa One or more control functions does not work Make sure that you know how to use those control functions according to this User Manual In case that any of the control functions do not cause any change of response in the detector functions then return the detector to your dealer for check and possible repair The detector is unstable Make sure not to use the detector with full Sensitivity while using fast Recovery speed setting Fast Recovery setting and high Sensitivity together will result in considerable amount of chatter in the loudspeaker and or headphones If this is not the case check for sources of electronic interference Using Silent motion will re
Download Pdf Manuals
Related Search