User`s Manual
Contents
1. If trouble is experienced with this equipment for repair and or warranty information contact Linear Corporation at 1 800 421 1587 for information or a return product authorization RPA If the trouble is causing harm to the telephone network the telephone company may request you remove the equipment from the network until the problem is resolved User repairs must not be made Doing so voids warranty This equipment must not be used on telephone company provided public coin service Connection to party lines is subject to state tariffs Contact your state public utility commission for information This equipment is hearing compatible HAC to any HAC compatible attached handset telephones Alarm Dialing Equipment If your home has specially wired alarm equipment connected to the telephone line ensure that the installation of any other non alarm devices does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer When Programming Emergency Numbers Or Making Test Calls To Emergency Numbers 1 Remain on the line and briefly explain to the dispatcher the reason for the call 2 Perform such activities in the off peak hours such as early mornings or later evenings 3 Follow the central station operator s instructions for updated dialer programming if re programming of the dialer is required Alarm dialing equipment must be able to2. 6 WHEN THE CALL IS FINISHED PRESS 9 TO HANG UP THE CONSOLE HAS A TIMER THAT WILL END THE CALL AUTOMATICALLY AFTER A PRESET TIME Reminder Messages The Console can play voice messages at pre set times This is an optional feature and may not be available on your system YOU CAN RECORD PLAY AND ERASE REMINDER MESSAGES YOUR MONITORING COMPANY SETS THE TIME REMINDER MESSAGES WILL AUTOMATICALLY PLAY RECORDING REMINDER MESSAGES PRESS AND RELEASE THE TEST BUTTON TO ENTER TEST MODE PRESS AND HOLD THE HOME BUTTON FOR 5 SECONDS BE READY TO RECORD RECORD UP TO A 15 SECOND MESSAGE SPEAK AT NORMAL VOLUME TWO FEET FROM CONSOLE PRESS THE HOME BUTTON TO STOP RECORDING PRESS THE HOME BUTTON AGAIN TO PLAY THE MESSAGE JUST RECORDED PRESS THE HOME BUTTON TWICE AND HOLD IT AFTER THE 2ND PRESS TO RECORD ANOTHER MESSAGE IN THE NEXT AVAILABLE MESSAGE NUMBER REPEAT STEPS 2 5 FOR ADDITIONAL MESSAGES UP TO 8 MESSAGES ALLOWED PRESS AND RELEASE THE CANCEL BUTTON TO EXIT TEST MODE TEST PLAYING REMINDER MESSAGES 1 PRESS AND RELEASE THE TEST BUTTON TO ENTER TEST MODE 2 PRESS AND RELEASE THE HOME BUTTON 3 THE CONSOLE WILL ANNOUNCE EACH MESSAGE NUMBER THEN PLAY THE RECORDED MESSAGE 4 PRESS THE HOME BUTTON TO ADVANCE TO THE NEXT MESSAGE TO BE PLAYED ST 5 PRESS AND RELEASE THE CANCEL BUTTON TO Oe EXIT TEST MODE NOTE TIME SCHEDULING FOR PLAYING REMINDER MESSAGES IS SET BY THE MONITORING COMPANY ERASING ALL
3. and these facts should be communicated to the ultimate users Service Information For service refer to the information below Your Monitoring Company Installation Warnings Be sure and test your system monthly Do not bring any electrical appliances or electrical noise generating devices fluorescent lamps motors etc near the Console Do not use ammonia benzene thinner or similar solvents or abrasive powder to clean the housing of the Console or Pendant Clean by wiping with a damp soft cloth The Console should be kept free of dust and moisture The Console should not be located where direct sunlight will shine on it Avoid locating the Console in extremely hot or cold locations Copyright 2008 228306 A
4. ONE END OF THE TELEPHONE CORD INTO THE LINE JACK ON THE REAR OF CONNECT THIS JACK THE CONSOLE CONNECT THIS JACK reenact TO LABELED LINE TO YOUR PLUG THE OTHER END OF THE TELEPHONE WALL JACK OPTIONAL TELEPHONE CORD INTO YOUR TELEPHONE JACK 6 YOUR TELEPHONE WALL JACK YOUR TELEPHONE OPTIONAL CONSOLE POWER CONNECTION PLUG POWER SUPPLY THE CONSOLE RECEIVES POWER INTO AN UREEWITCHEB FROM THE SMALL SQUARE AC OUTLET POWER SUPPLY ATTACHED TO THE CONSOLE S POWER CORD PLUG THE POWER SUPPLY INTO AN UN SWITCHED 120 VAC POWER OUTLET AN OUTLET THAT S NOT CONTROLLED BY A WALL SWITCH Testing It s important to test your system at least once a month BEFORE TESTING CALL YOUR MONITORING COMPANY TO NOTIFY THEM THAT YOU WILL BE TESTING THE TEST CAN BE MADE FROM THE PENDANT OR CONSOLE TESTING FROM THE PENDANT PRESS THE PENDANT S BUTTON UNTIL YOU HEAR EMERGENCY CALL BEING PLACED FROM THE CONSOLE S SPEAKER WAIT TO HEAR THE OPERATOR S VOICE FROM THE CONSOLE THE WAIT SHOULD NOT BE MORE THAN TWO MINUTES FOLLOW THE INSTRUCTIONS FROM THE OPERATOR TESTING FROM THE CONSOLE PRESS THE HELP BUTTON ON THE CONSOLE ONE TIME YOU WILL HEAR EMERGENCY CALL BEING PLACED FROM THE CONSOLE S SPEAKER WAIT TO HEAR THE OPERATOR S VOICE FROM THE CONSOLE THE WAIT SHOULD NOT BE MORE THAN TWO MINUTES FOLLOW THE INSTRUCTIONS FROM THE OPERATOR In Case of Emergency A call for help can be made wit
5. REMINDER MESSAGES 1 PRESS AND RELEASE THE TEST BUTTON TO ENTER TEST MODE 2 PRESS AND HOLD THE HOME BUTTON FOR MORE THAN 10 SECONDS 3 CAUTION THE CONSOLE WILL ERASE ALL REMINDER MESSAGES AND PLAYBACK SCHEDULES p 4 PRESS AND RELEASE THE CANCEL BUTTON TO Eme EXIT TEST MODE Nim Mius Activity Timer The Console can check for lack of daily activity and automatically call This is an optional feature and may not be available on your system THE ACTIVITY TIMER DURATION IS SET BY YOUR MONITORING COMPANY WHEN THE ACTIVITY TIMER IS RUNNING 4 THE HOME INDICATOR WILL LIGHT SHOWING THAT THE ACTIVITY TIMER IS RUNNING WHEN THE ACTIVITY TIMER IS RUNNING OUT OF TIME 2 THE HOME INDICATOR WILL BLINK AND THE CONSOLE ANNOUNCES EVERY 10 SECONDS WHEN LESS THAN 15 MINUTES OF TIME REMAIN ON THE ACTIVITY TIMER RESETTING THE ACTIVITY TIMER TO PREVENT AN INACTIVITY CALL 3 You NEED TO PRESS THE HOME ND BUTTON OR TRIGGER AN ACTIVITY 778 WA SENSOR BEFORE THE TIMER EXPIRES Ong TO PREVENT AN INACTIVITY CALL TO H THE MONITORING COMPANY Q PRESSING THE HOME BUTTON RESTARTS THE TIMER Testing Log Use this log to document your monthly system testing dates DATES TESTED A WARNING Battery Safety A Batteries must be recycled Deliver the battery to an appropriate recycling facility or ship it to the supplier in the replacement battery s packing material CAUTION Do not dispose of batteries in a fire The bat
6. THE STEPS ON PAGE 4 Telephone Modes The Console can be used as a speakerphone This is an optional feature and may not be available on your system NOTE SPEAKERPHONE MODE CAN ONLY BE USED ON INCOMING CALLS AND WILL NOT FUNCTION WHEN THE CONSOLE IS OPERATING FROM BACKUP BATTERY POWER ATTEMPTING TO ANSWER WHILE THE CONSOLE IS ON BACKUP POWER WILL CAUSE AN EMERGENCY ALARM O WHILE THE TELEPHONE IS RINGING ACTIVATING AN EMERGENCY PENDANT OR PRESSING THE CONSOLE S HELP BUTTON WILL ANSWER THE TELEPHONE YOU CAN TALK TO THE CALLER USING THE CONSOLE AS A SPEAKERPHONE WARNING THE CONSOLE WILL NOT BE ABLE TO REPORT AN EMERGENCY WHILE THE SPEAKERPHONE IS ACTIVE NOTE TO REPORT AN EMERGENCY WHEN THE SPEAKERPHONE IS IN USE PRESS EITHER THE HELP BUTTON OR A PENDANT BUTTON TO END THE PHONE CALL AND THEN PRESS ONE OF THESE BUTTONS AGAIN TO REPORT THE EMERGENCY G WHEN YOUR CALL IS FINISHED PRESS THE HELP BUTTON OR PRESS A PENDANT BUTTON TO HANG UP THE TELEPHONE THE CONSOLE HAS A TIMER THAT WILL END THE CALL AUTOMATICALLY AFTER A PRESET TIME AUTOMATIC ANSWER SPEAKERPHONE MODE CAN BE STARTED BY A CALLER a CALL THE CONSOLE S NUMBER LET IT RING THREE TIMES THEN HANG UP 2 WAIT ABOUT 10 SECONDS THEN CALL THE CONSOLE A SECOND TIME 3 WHEN THE CONSOLE ANSWERS A TONE WILL SOUND FOR 8 SECONDS WHEN THE TONE ENDS ENTER THE 4 DIGIT PASSWORD 1 2 3 4 OR FOLLOWED BY THE KEY 5 HAVE A CONVERSATION THROUGH THE CONSOLE S SPEAKER
7. seize the telephone line and place a call in an emergency situation It must be able to do this even if other equipment telephone s answering system computer modem etc already has the telephone line in use To do so alarm dialing equipment must be connected to a properly installed RJ31X that is electrically in series with and ahead of all other equipment attached to the same telephone line If you have any questions concerning these instructions you should consult your telephone company or a qualified installer about installing the RJ31X jack and alarm dialing equipment for you Alarm Installation Notes to Installer For products equipped with an RJ31X jack the line seize feature shall be verified Be certain the local telephone and incoming line connections are not reversed These lines are not reversed if the alarm dialer can communicate with the central station New Services Notes to User The installation and or monitoring company shall be notified if new telephone service e g DSL is installed For Canadian Installations The Industry Canada IC label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements The IC does no guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local teleco
8. User s Manual PERS 3600B Personal Emergency Reporting System Important Please test your system once a month See Page 4 Table of Contents System Components Installation Testing In Case of Emergency Pendant Replacement Telephone Modes Reminder Messages Activity Timer Testing Log Important Information Service Information System Components Your system may contain these or additional components TELEPHONE CORD EMERGENCY PENDANT SHOWN WITH WRIST STRAP EMERGENCY STATUS INDICATOR NORMALLY OFF ON OR BLINKING CALL FOR SERVICE o 11J 0 o HA Hn oo 000 0 000 PETTITT ITY HHTH POWER INDICATOR LIGHTS WHEN AC POWER IS PRESENT BLINKS SLOWLY WHEN BATTERY IS CHARGING BLINKS QUICKLY WHEN AC IS ABSENT MAKE SURE POWER SUPPLY IS PLUGGED INTO AN UN SWITCHED OUTLET AND THAT THE BUILDING HAS POWER CONSOLE SENDING INDICATOR NORMALLY OFF FLASHES WHEN CONSOLE Zo IS PLACING A CALL HOME INDICATOR NOT USED IN SOME INSTALATIONS LIGHTS WHEN ACTIVITY TIMER IS ON BLINKS SLOWLY WHEN LESS THAN 15 MINUTES REMAIN ON THE ACTIVITY TIMER BLINKS QUICKLY WHEN THE ACTIVITY TIMER HAS EXPIRED Installation Your system connects to the telephone line and power outlet TELEPHONE LINE CONNECTION PLACE THE CONSOLE IN A CENTRAL LOCATION IN YOUR HOME BE SURE IT IS ON A FLAT STABLE SURFACE AWAY FROM OTHER ELECTRIC DEVICES FANS RADIOS FLUORESCENT LAMPS ETC PLUG
9. all the devices does not exceed 100 The Ringer Equivalence Number REN is used to determine the quantity of devices that may be connected to the telephone line Too many devices may result in some devices not ringing in response to an incoming call In most but not all areas the sum of the REN s should not exceed five 5 0 To be certain of the number of devices that may be connected to the line contact the telecommunications company to determine the maximum REN for the calling area Refer to the equipment label for the unit s load number or REN number Important Wireless Information Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling However there are some imitations which must be observed For U S installations only The radios are required to comply with FCC Rules and Regulations as Part 15 devices As such they have limited transmitter power and therefore limited range A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating requencies regardless of code settings Changes or modifications to the device may void FCC compliance Infrequently used radio links should be tested regularly to protect against undetected interference or fault A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer
10. h the Pendant or Console CALLING FOR HELP WITH THE PENDANT IF YOU NEED HELP PRESS THE BUTTON ON THE PENDANT FOR AT LEAST TWO SECONDS NOTE THE PENDANT MUST BE WITHIN 150 FEET OF THE CONSOLE YOU WILL HEAR EMERGENCY CALL BEING PLACED FROM THE CONSOLE S SPEAKER WAIT TO HEAR THE OPERATOR S VOICE FROM THE CONSOLE THE WAIT SHOULD NOT BE MORE THAN TWO MINUTES FOLLOW THE INSTRUCTIONS FROM THE OPERATOR DO NOT PRESS CANCEL BEFORE TALKING TO THE OPERATOR OR YOUR CALL WILL NOT BE PLACED CALLING FOR HELP WITH THE CONSOLE IF YOU NEED HELP PRESS THE HELP BUTTON ON THE CONSOLE FOR AT LEAST TWO SECONDS DO NOT PRESS THE HELP BUTTON MORE THAN ONCE PER EMERGENCY YOU WILL HEAR EMERGENCY CALL BEING PLACED FROM THE CONSOLE S SPEAKER WAIT TO HEAR THE OPERATOR S VOICE FROM THE CONSOLE THE WAIT SHOULD NOT BE MORE THAN TWO MINUTES FOLLOW THE INSTRUCTIONS FROM THE OPERATOR DO NOT PRESS CANCEL BEFORE TALKING TO THE OPERATOR OR YOUR CALL WILL NOT BE PLACED Pendant Replacement Follow these steps to add a replacement Pendant to the Console ONE PENDANT CAN BE ADDED AT A TIME USING THESE STEPS CANCEL 0000000 D0000 ADDING A PENDANT PRESS THE CANCEL BUTTON ON THE CONSOLE FOR FIVE SECONDS THE CONSOLE WILL ANNOUNCE READY TO LEARN SENSOR PUSH THE BUTTON ON THE NEW PENDANT TO BE ADDED THE CONSOLE WILL ANNOUNCE NEW EMERGENCY SENSOR LEARNED PENDANT TEST THE NEW SENSOR USING
11. ivalence number code REN is used to determine the quantity of devices that may be connected to the telephone line Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call If most but not all areas the sum of the RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to the line as determined by the total RENs contact the telephone company to determine the maximum REN for the calling area For products approved after July 23 2001 the REN for this product is part of the product identifier that has the format US AAAEQ TXXX The digits represented by the are the REN without a decimal point e g 03 is REN of 0 3 For earlier products the REN is separately shown on the label If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required But if advance notice is not practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe it is necessary he telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service
12. mmunications company The equipment must also be installed using an acceptable method o connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly telephone extension cord The customer should be aware that compliance with the above conditions may not preveni degradation of service in some situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas CAUTION Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate The Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Number of
13. teries may explode CAUTION Do not open or mutilate batteries They contain an electrolyte which is toxic and harmful to the skin and eyes CAUTION To avoid personal injury due to energy hazard remove wristwatches and jewelry such as rings when replacing batteries Use tools with insulated handles Replacement and Recycling of Batteries See your dealer for information on replacement battery kits and battery recycling Ad NON SPILLABLE BATTERY GS Lx Pb CONTAINS SEALED LEAD ACID BATTERY MUST BE RECYCLED Important Information System regulatory information For United States Installations This equipment complies with Part 68 of the FCC rules and or the requirements adopted by the Administrative Council for Terminal Attachments ACTA On the bottom of this equipment is a label that contains among other information a telephone products identifier in the form FCC ID EF4 or US EF4 and ringer equivalence number REN If requested this information must be provided to the telephone company A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements as adopted by the ACTA If provided a compliant telephone cord and modular plug is included with this product The jacks and plugs are designed to be connected to a compatible modular jack that is also compliant See installation instructions for details A ringer equ
Download Pdf Manuals
Related Search