Technical Documentation: Sonoscout Setup Guide
Contents
1. wav Wave file default e hdf Hierarchical data format Streaming em Streaming x Frequency Range 512kHr gt Foi Par 512kHr gt pti PULSE Time file et Il X i bkc Br el amp Kj r common file Project name Streaming Project name Streaming n nd sa 7 Enter a Project name and Base filename Add to Base name incrementing gt Project name The name of the folder where the file will be written cm NM comete utet f me e NM commete ovest The default is Streaming Chi Channel 1 Enabled gt Chi Channel 1 Enabled gt nae Ed cc MESE Base name File name used for all recorded files The default is Cha Channel 3 Enabled Ch3 Channel 3 Enabled Test Cha Chana push ae Searels 8 In Add to Base name define a file extension This is appended to pec clic aun the Base name Select either Incrementing number or Date and Time 9 Swipe to close the Settings menu You are now ready to start a recording 7 ee 10 Tap the Pre recording button to initialise the system There is a treme Hi E short delay whilst the front end is being configured EM The enabled channels on the Front end will light up green minimi EN The time counter will light up showing 00 00 00 0 eer ji The Peak Level Meter will display green bars mo The Level History display will initiate aa E i If you are streaming data data streaming starts im2. 2 0 LAM Switch Sw labsncy natn ferme iE tet poa fla T r mela x r LI E ar Fr Wan if n H edule vandals FT ET 1 The Network page allows you to set a static IP address not recommended with wireless connection or obtain a new DHCP IP address 2 The Synchronization page shows the current synchronization method in use not relevant for single stand alone modules 3 The Status page shows the status of the Front end including self test status temperature power etc 4 The Firmware page shows the Front end s current firmware and provides detailed information on firmware updates NOTE It is not possible to download or open files such as firmware updates using Apple Safari the default browser on iPad 17 CHARGING YOUR BATTERY 0 20 18 20 4096 Flashing LEDs 40 60 60 80 80 90 Solid LED Fully charged To check the charge level press the Status button on the Battery The status indicators are as shown to the left Each LED bar is equal to approximately 1 5 hours operation There are two ways you can charge the Battery e DC charge using Battery Charger ZG 0858 To utilize in vehicle cigarette lighters use the included Car Utility Socket Cable AO 0546 AC charge using Battery Charger ZG 0469 input range 100 240 V AC 50 60 Hz With either option it takes approximately three hours for the Battery to be fully charged 1 Ensure
3. Mode Settings Wi Fi Choose a Network ADSL az Wi Fi ET BK3660A 000000 ac BKmobile a Eres Wei rr Hor Gees ooo Enter Password Password ass From your mobile device s Home screen tap the Settings icon Select Wi Fi If Wi Fi connection is switched off turn it on by tapping the on off icon Under Choose a Network all available Wi Fi networks are listed Select the Sonoscout System s access point called BK3660A XXXXXX The access point is a secure network using WPA2 PSK and requires a key password Enter 3660xxxxxx NOTE The Sonoscout System network is a closed secure network Once connected you will not be able to access the Internet xxxxxx is the Front end s serial number START USING THE APP 12 Settings Frequency Range 51 2 kHr File format May 3 Project name Streaming Base name Test Add to Base name incrementing gt Channels m F9 Messi Chi Channel 1 Enabled gt Chi Channel 2 Erbe Ch Channel 3 Erni gt Ghi Channel 4 Enabled gt Ch5 Channel 5 Enabled gt Frequency Range 51 2kHz gt File format May gt Project name Streaming Base name Tent Add to Base name incrementing gt Channels Calirsia Detect Pei Chi Channel 1 Enabled gt Chi Channel 2 Enabled Cha Channel 3 Dabid Chi Channel 4 Enabled gt Chi Channel 5 Enabled gt Settings Frequency Fange 512kHr gt File
4. Using the Front end Home Page cccccceceeeeseseseseeeeeeeeeeeeeees 16 Charging Your Battery 18 WHAT IS IN SONOSCOUT The Sonoscout app is available for download via the App Store M or iTunes To record sound and vibration data with the app you need to have the following LAN XI hardware an input module a battery module and a wireless LAN frame You will also need a Sonoscout license You can use your pre existing LAN XI modules and add Sonoscout License BZ 5950 L and Wireless LAN Frame Type 3660 A 200 or acquire a Sonoscout Kit which includes all of the above inventory in one portable case 130216 Inside the Sonoscout Kit case 1 2 LAN XI Battery Module Type 2831 A including mains charger LAN XI Input Module 4 6 or 12 channel module with license 3 Car Utility Socket Cable AO 0546 4 1 module Wireless LAN Frame Type 3660 A 200 5 Compartments for all system accessories such as a mobile device The System is pre configured including Sonoscout License BZ 5950 L and ready to use Simply set up your mobile device and Sonoscout app Recommended accessories Available from Br el amp Kjaer LAN XI Notar BZ 7848 A To record data to an SD card Apple iPad UL 1029 e Sound Calibrator Type 4231 To calibrate acoustic transducers Calibration Exciter Type 4294 To calibrate vibration transducers e Sound Quality HATS Type 4100 D For sound quality testing Binaural Recording Hea
5. the Battery s power switch is in the Active position 2 Plug the charge cable into the Frame s charge input connector Included with the Battery Apple iPad iTunes and Safari are trademarks of Apple Inc registered in the U S and other countries App Store is a service mark of Apple Inc Wi Fi is a registered trademark of Wi Fi Alliance EVERNOTE is a registered trademark of Evernote Corp in the U S and or other countries Ram Mounts is a registered trademark of National Products Inc iTunes is for legal or rightholder authorized copying only Don t steal music r Ban eX WE NS yy ruel amp Kj r HEADQUARTERS Brtel amp Kj r Sound amp Vibration Measurement A S DK 2850 N rum Denmark Telephone 45 7741 2000 Fax 45 4580 1405 www bksv com info bksv com Local representatives and service organisations worldwide BR 8031 11
6. SONOSCOUT SETUP GUIDE Bruel amp Kj r 2013 Copyright Bruel amp Kjaer All rights reserved Sonoscout is an intuitive mobile device app that combines with a wireless data acquisition unit to form a complete and highly portable system for quick grab and go recordings and immediate measurement validation Measurements are controlled on your Apple iPad and a simple user interface lets you mark events and replay time histories promptly after recording This Setup Guide will help you get started using your Sonoscout Apple support information To find out more about using apps on your mobile device check out the following websites e www apple com support ipad assistant application www apple com support ipad e support apple com manuals ipad e support apple com manuals iphone Sonoscout is compatible with iPad 2 or later running iOS 6 or later WHAT IS IN THIS GUIDE MAS I SON SEO i ZR 2 EDA O e E A E 3 Configure Your Front end essen 4 Connect Your Transducer eese 7 Power up Your Front end aa aan tpuneuS ind a aa na Regu UUDS 8 Install Your Sonoscout License sssssssses 9 Download the Sonoscout App ssssssseeeeemme 10 Set up the Wi Fi Connection eese 11 olan USING ADD T 12 Make a Quick Recording sessa 14 Updating Front end Firmware cccccccccecccccececececeeceeeeeeeeeeeeeeeeeeeeees 15
7. WNLOAD THE SONOSCOUT APP To download the app you must be connected to the Internet and have an Apple ID See your mobile device s user manual or the Apple website http appleid apple com for information on Apple IDs NOTE The Sonoscout app is free of charge Download directly on your mobile device From your device s Home With the App Store open tap in e Tap Search on the keyboard After the Sonoscout app is screen tap the App Store icon the Search field and enter displayed tap FREE then tap Sonoscout INSTALL APP ee E Sonoscout Download via iTunes for example on a remote PC You can download the app on your PC and then when possible synchronize your iTunes library over Wi Fi This requires that your mobile device is synchronized with iTunes If it is not see Settings General iTunes Wi Fi Sync on your mobile device for instructions 1 iTunes on the PC G From the menu bar With the App Store After the Sonoscout When your mobile select Store gt Home open enter Sonoscout app is displayed click device and PC are on in the Search field FREE to start the same Wi Fi you download can sync iTunes HP Sj Tuc MEL Sayre Lem EA pm T agg ven a Tunes La E ji ee ES d Q Sonoscout ightsenbe Direct Disc Labeling po McAfee Secunty Scan Plus DK W7 MIHUI Microsoft Office x 10 SET UP THE WI FI CONNECTION Connect your mobile device with the Sonoscout System network Se Airplane
8. ates you must use a PC Apple Safari and iOS systems do not support zip files Step 1 Download the Firmware Update Step 2 Install the Firmware Update A Go to www bksv com F Connect the PC to the Front end s wireless access point B Select Service gt User Support gt Downloads G Open a Web browser and enter the IP address from the Front end s C In the Step 1 box select LAN XI display into the address line D In the Step 2 box select LAN XI Software Updates H On your Front end s home page click Firmware E Click the latest firmware filename and Save the zip file to any location Click Browse and navigate to the saved file on your PC J Click Start update USING THE FRONT END HOME PAGE ow Br el amp Kj r d C MAET D Peo FX We help cur customers improve me quality of sound and vibration and related human comfort Main About this module Module type 3160 A 042 Hatvrerk Description Generator amp 2 ch Input Cutpst Module LAN XI 51 2kcHMz Mic CICLO V Synchronization indict serial number Status Front pane Hosbname Firmware Rass module Turn gn mecum indiabar Open reconder application 16 Each LAN XI module and frame has its own home page containing information about the module including configuration calibration history self test log file etc To access the home page 1 With your mobile device connected to the Front end s access po
9. dset Type 4965 For real time audio e 4 channel CAN 2 Analogue Converter ZH 0700 Transducers as required Available from third parties e Suction Mount To attach iPad to car windscreen Cradle for iPad Both available from RAM Mounts www rammount com NOTE Sonoscout Kits are not delivered with mobile devices SETUP BASICS aD Configure your front end o Connect your transducer Power up your front end Install your Sonoscout license Download the Sonoscout app Set up your Wi Fi connection Hx Start the application Make a basic recording 00 00 00 000 This step is not necessary if you have purchased Sonoscout Kit Type 3663 A 040 3663 A 060 or 3663 B 120 CONFIGURE YOUR FRONT END Front end configuration is only needed if you purchased your LAN XI modules separately not in a Sonoscout Kit What do you need What do you do 1 LAN XI Wireless LAN Frame Type 3660 A 200 referred to as the Front end configuration is a 2 step process Frame 2 LAN XI Battery Module Type 2831 A referred to as the Battery 3 LAN XI Module referred to as the Input Module 4 An SD card if using LAN XI Notar BZ 7848 A NOTE Type 3660 must have firmware version 2 1 0 190 or later to use the Sonoscout app All pre configured systems have the correct firmware installed If you are using an earlier firmware version please see Updating Front end F
10. format May gt Project name Streaming Base name Test Add to Base name incrementing Channels Cadbbrate Debert Resa Chi Channel 1 Enabled gt Ch2 Channel 2 Enabled gt Cha Channel 3 End Ch4 Channel 4 Enabled gt Chi Channel 5 Enabled gt Start the app 1 From your Home screen select the Sonoscout app icon The application will start and open in the Recording task see the bottom of the user interface for the task icon ISI e f the app has not detected the Front end the Status line will be blank Set up the hardware and recording 2 From the left edge of the screen swipe toward the centre to open the Settings menu to set up the hardware all Front end channels will have default settings 3 If you have TEDS transducers connected tap Detect and the app will automatically fill in the details NOTE Tap at the top of the user interface and select Help for instructions on setting up the hardware manually Manual setup is necessary with LAN XI Notar as it does not currently support all TEDS transducers 4 Select the recording file location Save to the SD card on the Front end tap Streaming to Off Save to your mobile device keep Streaming set to On default 5 Set the Frequency Range Data are sampled at 2 56 times this frequency The default is 25 6 kHz Only available when used with LAN XI Notar BZ 7848 A amp 6 Select the File format the recording will be saved as
11. int open a Web browser 2 Enter the IP address shown in the Front end s display into the browser s address line for example 192 168 1 229 The Main page looks similar to the one shown here with the Front end s general settings The two links on the page can be set as needed Location Where the module is physically located Contact Who to contact either an email address or phone number The buttons at the bottom provide the following functionality Reboot module Reboot the module to factory settings Turn on module indicator Enables the module s LED indicators to light up in the case of multi module configurations not relevant for single stand alone modules Open recorder application Use this button to control a recording using LAN XI Notar and or access the data stored on the SD card Hain Heterot k Syechronlrathon Stab Firmware Haim Nebak Sysschronairaliom Sal Firmware ita Satana Pieria dell bel Pops tat succeeded iieri saberi By connectedi ta any chena Lagt er Lii User Lag Appbcaon Temprraldurg Models herrar dio C 108 8 4 Power status Modos poner pour H input rau ALD Tne of E n 3 a EE S Hetw rk sykri ra ir Stafur Ferna re Synchronization Sith Sand PTE are PTF barra Bibi saree Cerner grncdsaimer Grandmaster breceatabby fo UTC Pares chek Pretend asper Bede Slave Offset to Master Blase me gtaceiand deo
12. irmware on page 15 for instructions Step 1 Connect the Input Module to the Battery Step 2 Connect the Frame If you have LAN XI Notar BZ 7848 A you may need to insert the SD card before connecting the Frame Normally this is done at the factory Front end Configuration Step 1 Connect the Input Module to the Battery The Battery provides mobile power to the Front end during recording A Place the Battery behind the Input Module so that the type number text on both of modules is facing the same direction and the Battery is to the left of the Module B Remove the hex key from the Input Module C Using the hex key push out the four spring loaded screws around the Input Module D Fasten the screws to the Battery module and place the hex key back into place Front end Configuration Step 2 Connect the Frame E If you have LAN XI Notar BZ 7848 A ensure that the memory card is inserted in the mini SD slot at the back of the Input Module F Align the prongs on the Frame with the holes at the back of the assembled Input Module and Battery unit Insert carefully Magnets hold the Frame into place To ensure connection during use you should screw the Frame securely into place G At the side of the Frame is a hex key remove it and pull open the Frame H Using the hex key turn the captive screw in the middle of the Frame until it is tightened Close the Frame and place the hex key back into p
13. lace Use of an SD card is not mandatory You can also stream recorded data directly to your mobile device s internal storage CONNECT YOUR TRANSDUCER Both microphones and accelerometers or any other voltage input can e be used LEMO BNC and SMB connections are supported all depending on your Input Module s front panel threads In the case of microphones make sure that you do not touch gt i When connecting the Transducer do it gently to avoid damaging the diaphragm with anything as it is very delicate 1 Assemble your Transducer and Preamplifier if necessary 2 Connect the relevant cable plus adaptor where necessary to the Transducer 8 r Transducer connection examples 3 Connect the cable to the Front end Turn the cable end into place With LEMO connections align the red dot at the cable end with the red dot on the Front end connector Front panel connector compatibility e LAN XI BNC connectors are compatible with any RG58 5 Q cable LAN XI LEMO connectors are LEMO 1B use either Br el amp Kjaer s LEMO OB to LEMO 1B Connector Cable AO 0419 12 ch SMB LEMO 1B to LEMO 1B Extension Cable AO 0414 e LAN XI SMB connectors are compatible with RF Coax SMB connectors such as Farnell 1212896 Tyco Electronics 1 1337475 0 8 LEMO 6 ch LEMO P Q SS For CAN data support use 4 channel CAN to Anal
14. mediately MAKE A QUICK RECORDING 1 Tap the Rec button The button flashes and recording starts immediately B z s 2 To view real time displays use the sub task tabs at the top of the interface For a spectrum display tap the Spectrum tab and select the channel For a RPM profile display tap the Profile tab and select the channel For a time history display tap the History tab and select the channel 3 To pause the recording tap the Rec button The button will change to a pause icon To restart tap the Pause icon The recording will continue and the data will be appended to the same file 5 4 To stop the recording tap the Stop button There will be a short delay before file writing is complete Channel selection Test B ll wl a ee CI 5 If you are streaming data streaming will continue until you tap the REC N x Stop Streaming button happa For detailed instructions on use of the app including user interface descriptions in depth setup instructions and file handling and display tips simply tap at the top of the screen and select Help Tap to restart 14 UPDATING FRONT END FIRMWARE Br el amp Kjaer continually updates LAN XI firmware and provides the updates in zip files on the Br el amp Kjaer website www bksv com Once the file is downloaded from the Internet install the update via the Front end s home page To download and install firmware upd
15. mory stick from Br el amp Kjaer or saved on a PC or mobile device using for example Evernote9 Wireless device with Web browser PC or mobile device e Password for your Front end What do you do 1 Enable your wireless device for wireless network Wi Fi connection From the available wireless Wi Fi networks available select the BK3660A xxxxxx access point 2 The access point is a secure network using WPA2 PSK and requires a key password Enter 3660xxxxxx bisia Vic evsssnck ieee teed im Uhre reuse m 3 Open a Web browser and from the Front end s display enter the Frans Add gem sa ae a displayed IP address in the browser s address line for example TR 192 168 1 229 and press Enters A 4 The Front end s unique Web page will open Click Licenses in the side menu Ld Briel Kj r w al Mais bra snar on ihis il Pise ri ia Frans Ad Ferr epe Save Fere acies Flatur Ci umen rl s aont Deb 10760 B r ML B eS ge ey wradg Lam ha Pea Ll Fa FEE naar Fireman 5 Open the text file with your license string and copy the string Paste it into the License key s box on the Web page and click Add The following licenses will be added for correct operation of Sonoscout e BZ 5950 Sonoscout e BZ 5951 LAN XI input channel streaming e BZ 7848 A LAN XI Notar if installed xxxxxx are the last six digits in the Front end s serial number DO
16. ogue Converter ZH 0700 POWER UP YOUR FRONT END Power up the Front end by moving the power switch on the Battery to Active The Input Module s display will initially show an IP address of 0 0 0 0 LAN XI modules are pre configured to use DHCP by default so you only need to power it on and after about five seconds the Front end s built in DHCP server will provide an IP address Setting your old module to use DHCP dynamic IP addressing For wireless communication the Front end must use dynamic IP addressing using DHCP If you are using a LAN XI module that did not come bundled in the Sonoscout Kit and have a static IP address you must reset the module to be a DHCP client To reset the module 1 Press and release the Control button on the front of the Input Module to display the menu 2 Scroll down the menu by pressing the button once for each menu item 3 Stop scrolling at LAN Reset Press and hold the Control button for 5 seconds NOTE You can also check the module s firmware version using the display menu Simply scroll down to Module Info in the menu and press and hold the Control button until the display changes If the Ver is earlier than 2 1 0 190 then you must update the firmware See page 15 for update instructions Press Control to scroll INSTALL YOUR SONOSCOUT LICENSE License installation is only needed if you did not purchase a Sonoscout Kit What do you need License text file on USB me
Download Pdf Manuals
Related Search