Wetroom Thermostat Installation Instructions
Contents
1. level you must use the backplate provided It should be positioned away from draughts direct heat and sunlight The Wetroom Sensor also needs the temperature probe plugged into the rear of the device and stowed away in the sensor housing provided which should be wall mounted in the wetroom area The backplate is suitable for direct wall mounting using two wood screws No 6 x 1 or M3 5 x 25mm into Polypipe Limited 2015 9 correctly sized wall plugs if required Alternatively mount on to a single gang flush wiring box complying with BS4662 using two M3 5 screws 1 Check Signal Strength With the thermostat at the chosen installation location you should now check the signal strength icon shown on the web dashboard Heat ing widget The signal should be at least 2 bars and preferably more Try moving the Heating Hub closer to the thermostat if you have a signal strength problem Ensure there will be enough space to allow easy screwdriver access to the two cap tive screws located at the base of the backplate Electrical Connections If in any doubt whatsoever do not continue but consult a qualified electrician or heating engineer WARNING ISOLATE THE MAINS SUPPLY BEFORE COMMENCING INSTALLATION For existing installations remove the old room thermostat to expose the wiring back to the heating system Check the wiring at both ends to correctly identify which wire is Live and which is Switched Live For new installations run a ne2. Control Thermostat Backplate Wiring Terminal Description Call for Heat Normally open terminal of Thermostat latching relay Earth continuity connection N Neutral Not used may be used to park unused neutral wire L Live Not used may be used to park unused live wire 1 Common terminal of Thermsotat latching relay 2 Not used 3 Not used 4 L Polypipe Limited 2015 15 Thermostat Delete Heating Hub Pairing You can delete the Thermostat to Heating Hub pairing by pressing both the Standby and Away buttons together for a minimum of 10 seconds count to 15 The 3 LEDs will start flashing indicating that it is in pairing mode Thermostat Factory Reset You can factory reset the Thermostat by pressing both the Comfort and Standby buttons together for a minimum of 20 seconds count to 25 The 3 LEDs will start flashing indicat ing that it is in Heating Hub pairing mode Thermostat LED Meanings LED Flash Cou meaning O y O Single every 1 second Battery running low 16 Polypipe Limited 2015 LEDS Meaning Cd Triple every 30 seconds In Holiday mode On 1 second Off 1 second Heating Pairing mode Scrolling Comfort Standby Away Relay Unit Pairing mode Single every 30 seconds In Away mode Polypipe Limited 2015 17 SAFETY INFORMATION To ensure that you use your product safely and correctly please read the warnings amp safety precau
3. Water Controls User Manual document by clicking on Manuals web dashboard lower right Customer Support If you have any further questions please check our frequently asked questions at https www polypipeufh com You can also call us on 01709 770000 please ensure you state your Heating Hub Unit MAC ID Polypipe Limited operate a policy of continuous development and improvement therefore the content of this document is subject to change without notice Issue 1 2 Wetroom Thermostat Installation Manual 22 Polypipe Limited 2015
4. ard 1 Configure System Settings Select the System menu Select an Property EPC Energy Efficiency Rating appropriate Energy Performance Rating Score Description Certificate EPC rating for this property Enter the actual EPC rating bead Exceptional if you have one if not just estimate B 81 91 ibne how you would rate the energy ef C 69 80 ease ficiency of the property on the A to D 55 68 G scale below Be sure to click the UK Average Save button before closing the E 39 54 window F 21 38 2 Configure Heating Settings G 1 20 Below Average You can make any necessary changes Polypipe Limited 2015 7 to the various Heating settings by clicking on the gear wheels icon on the grey Heat ing widget title bar Configure Time Clock The Heating Time Clock defines the periods during which the home is automatically heated and to what temperature These periods are called Comfort Periods Polyipe will intelligently calculate what time to switch the heating system on and off to maintain the target temperature for the whole of the Comfort Period Each day of the week can be programmed with up to 10 different Comfort Periods The preset heating Comfort Time Clock settings are shown in the table opposite These can be modified using the Polyp ipe web dashboard a On the Heating widget click on the Clock icon This opens the Heating Time Clock widget
5. b Select the day you wish to amend then click an option on the line you wish to amend Preset Heating Comfort Time Clock Settings Monday to Friday Start Time End Time Temperature 07 00 08 30 18 C 16 30 22 30 20 C Saturday amp Sunday Start Time End Time Temperature 07 30 10 00 18 C 16 30 22 30 20 C Note Outside of these preset heating Comfort periods the Room Sensor will be in Standby mode 15 C configurable Polypipe Limited 2015 i Pencil icon to edit the line ii Cross icon to delete the line c Amend details within the Edit box as required then click on the Tick icon to update the table d To add a new line simply fill in the Add box with the required details and click on the Tick icon e When you are happy with your changes you can use the Copy Current Day feature to quickly duplicate to other days f IMPORTANT When you have finished making changes you must save them to your Heating Hub Unit by clicking on the Save To Heating Hub button STEP FIVE Physical installation of the Thermostat Refer to the schematics and diagram shown on pages 12 amp 13 for the wiring arrangement for a typical heating system The diagram should be used for guidance only They can also be downloaded from the Polypipe web dashboard under Manuals The Thermostat should be located on an internal wall outside of the wetroom area ap proximately 1500mm above floor
6. back plate terminals and the screws are tight Then fit the Safety Cover by clipping it into place over the wiring terminals Complete the installation by mounting the Thermostat to the backplate To do this engage the Thermostat on the lugs at the top of the backplate then carefully swing Polypipe Limited 2015 11 Room Sensor For multiple zones using Slave unit PB1ZS paysios paH O wo E 4094 10 gt To Master Do not use connection on master for thermostat if using slave 2 Wire Actuators PBOO401 Max LU L A per zone 12 Polypipe Limited 2015 Room Sensor For single zone using using master PBIZM 1084 10 109 poysyos ay Olo E Remove link if Zone Valve Fitted Note Only use this connection when using a Single Room Thermostat If using Slave DO NOT use 230v S L Connection Boiler Power Supply Volt Free Contact Boiler Polypipe Limited 2015 13 the Thermostat down and push it carefully back into its plug in terminal connectors Locate over the captive screws at the base of the backplate and tighten them so that the Thermostat is locked into position Existing Programmer Time Clock any existing programmer or time clock is now redundant Y
7. f they come into contact with conducting materials heat corrosive materials or explosives Remove the batteries before storing the product for extended periods Only use fresh batteries Do not mix new and old batteries Do not dispose of old batteries as unsorted municipal waste only do so in accordance with your local waste disposal regulations When disposing of this product do so in accordance with your local waste disposal regulations GARING FOR YOUR PRODUCT Before cleaning remove the Thermostat from the backplate and remove the batteries Use a lightly dampened cloth Do not use liquid or aerosol cleaning agents benzene thinners abrasive or corrosive materials Do not scratch hard objects against the product Do not leave discharged batteries in the product COMPLIANCE The CE marking certifies that this product meets the main requirements of the European Parliament and Council Directive 1999 5 EC A copy of the signed and dated Declaration of Conformity is available on request Polypipe products are manufactured to ISO 9001 Quality Assurance Standards Polypipe Limited 2015 19 SPECIFICATIONS Thermostat Temperature accuracy typical Humidity accuracy typical 1 8 RH Relative humidity 25 to 95 non condensing 20 Polypipe Limited 2015 Page intentionally left blank Polypipe Limited 2015 21 For details on using your new Polypipe heating controls please download the Heating amp Hot
8. h username and password If this is a new system the installation amp configuration Wizard will automatically open For existing Polypipe installations you should start the Wizard by clicking the Wizard menu bar option at the top of the screen Select Heating Hot Water Control Ta from the drop down box Click the Sta rt button and follow Please use this wizard to ADD new monitoring or control elements to your the Wizard through these steps system Select Room Wetroom Thermostat nce ali devices have been setup io Start or click Finish from the drop down box in the Wizard Click the Next button and carefully follow Wizard on screen instructions to pair the Thermostat to the Heating Hub Fit Thermostat to its back plate Test for correct operation including safety switch must be closed for correct operation Click the Finish button Unless you have further Polypipe devices to install configure then click the Finish Introduction Heating Hot Water Control Polypipe Limited 2015 button e Click the OK button to close the Wizard The web dashboard will then automatically refresh itself and you should now have a Heating widget within the web dashboard STEP FOUR Log in and Configure If you are not already please log in to your Polypipe account with your username and password at https controlmyheating polypipe com You should now have a Heating widget within your web dashbo
9. ied separately For full details please refer to the Heating Hub installation guide supplied with that product however a summary of the steps are listed below 1 Connect Ethernet cable between spare active LAN port on your broadband Inter net router and the Heating Hub 2 Plug the power supply into the mains and insert the DC jack connector into the base of the Heating Hub 3 Wait until the green LED on the top of the Heating Hub is flashing with a triple blip pattern This should not normally take longer than 2 minutes 4 Do NOT proceed to STEP TWO until this flashing pattern is observed 4 Polypipe Limited 2015 STEP TWO Create Polypipe online account e If you are adding heating controls to an existing Polypipe installation then please jump to STEP THREE Log in and follow Wizard s If this is a new Polypipe installation then you will first need to create a new Polypipe account For full details please refer to the Polypipe installation guide supplied with that product however a summary of the steps are listed below 1 Using a web browser visit https controlmyheating poypipe com Click Create Account Check and confirm that the Heating Hub is online Fill in the information requested Click Create Account button Ensure successful account creation completion message is displayed oy OTs NS Polypipe Limited 2015 5 STEP THREE Log in and follow Wizard Log in to the Polypipe account wit
10. oO O Polypipe Wetroom Thermostat Installation Instructions Wetroom thermostat for zonal Underfloor heating temperature control for new installations or to replace existing Polypipe wired Room thermostats in wetroom environments Support for up to 10 separate heating zones Provides programmer time clock functionality Requires Heating Hub Unit to operate IN THE BOX i gt ve Wetroom Thermostat Backplate Safety Cover Temperature 2 x AAA Sensor alkaline battery Polypipe Limited 2015 1 Introduction This thermostat is a part of the Polypipe range of cloud connected monitoring and control products Its operation is dependant upon being paired to the broadband Internet connect ed Heating Hub Unit supplied separately The thermotstat provides both room thermostat and programmer time clock functionality Basic day to day user operation changes can be made using the three buttons Additionally there is comprehensive yet intuitive and easy to use control via the Polypipe web dash board Accessible from any Internet connected computer anywhere in the World iPhone and Android smartphone apps are also available for free download It is recommended that this product is installed by a suitably qualified heating engineer plumber or electrician Please read the Safety Information section of this document before proceeding 2 Polypipe Limited 2015 Version Information This thermostat is battery powered with a la
11. ou should either program it to be permanently on 24 7 or preferably remove it ensuring that the two wires it was switching are safely electrically linked together preferably by installing a link wire within the heating system Please check heating system manufacturers wiring instructions for further details Finally check that the Thermostat is functioning correctly and switching the heating system on and off correctly A simple test for this is to press and hold the Comfort button for 5 seconds This will activate the Boost mode and turn the heating system on Check that the web dashboard Heating widget is now showing that the Boost is activated and the heating system is running Red glow around house icon at top of Heating widget Handover Please ensure you handover this document to the householder and direct them to the Heating amp Hot Water Control User Manual available for download by click ing on Manuals on the web dashboard lower right Polypipe Limited 2015 Additional Information Safety Switch The Thermostat is fitted with a safety switch that is automatically activated when the front of the Thermostat is removed from the backplate Safety switch activation will immediately turn the heating off and the web dashboard will show an appropriate warning message The Thermostat MUST be installed onto the special backplate supplied otherwise the safety switch will not operate and the Thermstat will not work Polypipe Heating
12. tching relay It has 3 control buttons Comfort Standby and Away with associated LED indicators Installation Configurations Supported This thermostat can be used in several ways to suit various heating control needs Thermostat Type Wired connection Polypipe wired master or slave unit Multi Heating Zone Control A single Polypipe system can support up to 10 thermostats one for each heating zone in a wired configuration This flexibility enables Polypipe to be used to control heating systems that are Building Regulations Part L compliant and beyond Maximum Number of Devices Every Polypipe device within a single system e g Wet room thermostat Room thermostat must be paired to the Heating Hub The Heating Hub supports up to a maximum of 10 devices Polypipe Limited 2015 3 Installation Instructions Single or multiple heating zones If this is a single zone heating system then simply follow these instructions The Polypipe system will support up to 10 heating zones For additional thermostats simply repeat these instructions for each one required The web dashboard will automatically update the Heat ing widget with the additional device when you next log in STEP ONE Install Heating Hub Unit e If you are adding heating controls to an existing Polypipe installation then please jump to STEP THREE Log in and follow Wizard s If this is a new Polypipe installation then you will first need to install the Heating Hub suppl
13. tions below before installing your Polypipe Room Thermostat Isolate the mains power supply to the heating appliance that the Thermostat will be connected BEFORE commencing any wiring work If you are in any doubt about the Thermostat installation whatsoever DO NOT at tempt to install but consult a qualified electrician or heating engineer Before attempting to fix the backplate to the wall you must ensure that there are no electrical cables or pipes that will be damaged drilling the fixing holes Do not immerse the unit in water or other liquids If you spill liquid over it dry it immediately with a soft cloth Do not use or store the product in conditions that could adversely affect the product such as rain snow desert and magnetic fields Do not subject the product to excessive force shock dust temperature or humidity Keep the product away from heat sources radiators stoves heaters etc Do not use the product in or near water or in high moisture areas such as bathrooms Do not tamper with the product s internal components This invalidates the warranty Do not attempt to repair the product yourself Contact the retailer or Customer Services if your product requires servicing If the equipment is used in a manner not specified in this manual the protection provided by the equipment may be impaired Take care when handling all battery types Batteries can cause injuries burns or Polypipe Limited 2015 damage to property i
14. w cable between the heating system and chosen ther mostat Location The recommended cable size is 1 0mm See diagram Ensure that the Live feed to the thermostat is correctly fused 3A or 5A maximum This protection is normally provided by the Polypipe master wiring unit Fix the backplate Offer the backplate supplied to the Polypipe Limited 2015 wall in the position where the thermostat is to be mounted Drill and plug the wall then secure the plate into position The slots in the backplate will compensate for minor misalignment of the fixings Wiring All necessary electrical connections should now be made e The Thermostat is double insulated and does not require an earth connection e An earth connection block is provided on the backplate for terminating any cable earth conductors e Earth continuity must be maintained and all bare earth conductors must be sleeved e If one of the existing wires is a Neutral supply then this should be parked on the terminal labelled N e Ensure that no conductors are left protruding outside the central space enclosed by the backplate e Please ensure that all installations comply with the current IEE regulations e Please consult the heating system manufacturers installation instructions before making these connections and note that a link may need to be removed when con necting external controls Fit Safety Cover Check all of the wiring is safely attached to the appropriate
Download Pdf Manuals
Related Search