Corner shower unit with round front
Contents
1. Shower stall Corner shower unit aeance with round front Installation Guide and User Manual Model 1JPSOO4WHI ATTENTION 1 Your installation must comply with all local plumbing building codes Have a qualified tradesman do or approve your plumbing installation 2 Always wear safety goggles and gloves in order to avoid personal injury 3 Please read and save this guide before using this product Store the guide in a safe place so you will know where it is when you want to refer to it IMPORTANT Carefully check the unit prior to installation to ensure that there is no damage Do not dispose of any packaging until you are satisfied with this product If you have any problems with this product or if there are missing or damaged parts please call toll free 1 800 459 4409 Monday Friday 8 30 am 5 00 pm EST DO NOT RETURN THE UNIT TO THE PLACE OF PURCHASE BEFORE CALLING THE TOLL FREE NUMBER ABOVE PRODUCT FEATURES Our shower units are manufactured using top quality cast acrylic and are designed for years of comfort and enjoyment e Each unit is formed using 3 mm 178 in thick cast acrylic that provides an attractive easy to clean and maintain high gloss Surface e The acrylic surface resists chipping staining mold and mildew e Heavy duty construction Reinforced with fire retardant fiberglass Engineered base with leveling feet for easy installation e Tempered safety glass e Powde2. door with the wheels facing towards the outside of the curve Install the spring loaded assemblies on the two lower holes of the curved doors with the wheels facing towards the outside See Fig 15 mie sche or inat ee Eia 5n ath n cm oo Fixed roller assembly Spring loaded roller assembly Fig 15 9 As shown in Fig 16 install the completed glass door on the aluminum track by first inserting the spring loaded rollers at the bottom then lifting and placing the top rollers into the top track 1 2 Fig 16 INSTALLATION INSTRUCTIONS 10 Install the handles as shown in Fig 17 Place the gaskets on the curved glass doors with the flap facing towards the outside Slide glass door Inside Outside Fig 17 11 Apply silicone on the two vertical edges of the caddy all along the edges between the wall and the shower base on the two vertical expanders on the inside on the lower track and on the base as shown in Fig 18 CLEANING AND MAINTENANCE To maintain the smooth high gloss surface of your shower enclosure follow these tips Use common household cleaners non abrasive such as Lysol Basin Tub and Tile Cleaner Glass Plus Mr Clean Top Job or a mild liquid dish washing detergent such as Ivory Liquid Rinse well and dry with a clean cloth Do not allow your acrylic surface to come into contact with products such as acetone nail polish remover nail polish dry cl
3. anship for one 1 year from the date of purchase This warranty does not extend to commercial or institutional use or installation Incidental repairs that would involve a minimum of time and effort on behalf of the purchaser will not be considered warranty work and no compensation will be deemed forthcoming Any failure of the unit that is not traceable to a defect in material or workmanship is not covered by this warranty These non warrantable items include but are not limited to e Change in colour or finish due to chemical usage e Damage caused by the use of abrasive cleansers on the acrylic surface e Unit not properly installed in accordance with the manufacturer s instructions e Damage caused during shipping handling or installation eg cracks chips scratches e Damage caused by operating maintenance and safety guidelines not being followed e Any alterations to the unit e Damage to the unit as a result of accidental impact fire flood freezing or normal wear e Stress cracks caused by forced connections over tightened overflow plate inadequate support or standing on the tub ledge e Scratches chips cracks or holes caused during shipping storage or installation A thorough inspection must be made at time of pick up or delivery If the unit is damaged a claim must be made with the carrier Report any damage promptly and prior to installation Quality Craft will not be held liable for any freight damage
4. eaning solution lacquer thinners gasoline pine oil etc Remove dust and dry dirt with a soft damp cloth Clean grease oil paint and ink stains with isopropyl rubbing alcohol Immediately rinse with water after removal of stain Avoid using razor blades or other sharp instruments that might fall and scratch the surface Small scratches can be removed by applying a thin coat of automotive paste wax and buffing lightly with a clean cloth REPLACEMENT PARTS If you require replacement parts please call customer service toll free at 1 800 459 4409 Monday Friday 8 30 am 5 00 pm EST Identify your required part s and have the replacement part number ready when you call JPSDROO1 pE oe O a O JPSHWO01 gua ga sI cm JPSDHOO1 H iC comm JPSABO0O1 Spring loaded roller assembly x 4 Fixed roller assembly x 4 Pegs x 4 Plastic stoppers x 4 Stainless steel screws x 4 Caps x 4 Stainless steel screws x 8 Stainless steel screws x 6 Anchors x 6 Stainless steel screws x 4 Handle assembly x 2 Clips x 5 Stainless steel screws x 5 3 9mm x 13 mm 3 16 in x 1 2 in 3 9 mm x 40 mm 3 16 in x 1 1 2 in 3 9mm x 25 mm 3 16 in x 1 in 6mm x 25 mm 1 4 in x 1 in 3 9 mm x 9 5 mm 3 16 in x 3 8 in 3 9mm x 25 mm 3 16 in x 1 in ONE YEAR LIMITED WARRANTY Your shower unit is warranted to the original purchaser to be free of defects in material and workm
5. g by placing a carpenter s level as per Fig 3 Fig 3 Adjust the leveling legs as required so that the skirt of the base is 6 4 mm 0 25 in above the floor as shown in Fig 4 Make sure that all leveling legs make contact with the floor Tighten lock nuts to secure the leveling legs Check level again as well as that all legs make contact with the floor Studs TTE nh wae Drywall 6 4 mm 0 25 in min Raised flange _ Adjustable legs LU 6 4mm 0 25 in ZILLA Lock nuts INSTALLATION INSTRUCTIONS 6 py reer verre rere Remove the base Remove the lt Strainer strainer and wrench leaving the Some ais ieni ring and rubber collar in place from lt Ring the drain assembly and install the Rubber coll drain as shown in Fig 5 Apply gt jia silicone on the acrylic drain area Se where the fitting will make contact care Do not over tighten nut as the drain body may warp or break Secure the vertical drain pipe in place with 3 8 cm 1 5 in SES lt Rubber washer exposed above floor level See STS lt Paper washer Fig 6 L lt lt Locking nut The shower base must be set in Fig 5 a bed of mortar Lay the mortar in the areas where the metallic frame is located 5 1 cm 2 in of clearance should be left around the drain pipe hole Lubricate the exposed pipe and the inside rubber collar of the drain with soapy water Set the base int
6. g saw 1 8 drill bit Pencil Carpenters level Shower Base x 1 Aluminium Expander x 2 Aluminium Tracks x 2 Aluminium Vertical Pieces with Glass Channel x 2 d Flat Fixed Glass x 2 Curved Glass Door x 2 Long Gasket with Flap x 2 Short Gasket with Flap x 2 JAIL Ao Anchors x 6 Handle Pegs x4 Caps x 4 Plastic 6mmx25 mm Assembly x 2 Stoppers x 4 1 4 in x 1 in B Clips x 5 Fixed Roller Spring Loaded Stainless Steel Stainless Steel Assembly x 4 Roller Assembly x 4 Screws x 6 Screws x 4 3 9 mm x 25 mm 3 9 mm x 9 5 mm 3 16 in x 1 in 3 16 in x 3 8 in m mm G Stainless Steel Stainless Steel Stainless Steel Screws x 4 Screws x 5 Screws x 8 3 9 mm x 13 mm 3 9 mm x 25 mm 3 9 mm x 40 mm 3 16 in x 1 2 in 3 16 in x 1 in 3 16 in x 1 1 2 in INSTALLATION INSTRUCTIONS BASE INSTALLATION 1 If installing in a location where drywall has already been set up confirm that it is water resistant drywall Once the location of the shower enclosure and base has been established and the drywall has been confirmed to be water resistant mark the two walls as per Fig 1 If the drywall is not the appropriate type remove from the total area where the shower enclosure is to be installed and skip the next step Cut drywall leaving the studs exposed Mark the position of the drain as per Fig 2 Cut the floor with a jig saw approximately 12 7 cm 5 in in total diameter Put the base in place and begin levelin
7. he shower base 2 Trace the holes that are ore drilled on the expander 1 to locate them on the wall 3 Drill holes on the wall at the position of the marks and install the anchors 4 Fix the expanders to the walls 12 7 mm starting from the top anchor 0 5 in using 3 9 mm x 25 mm 3 16 in x 1 in stainless steel screws as shown in Fig 10 5 Using 3 9 mm x 40 mm 3 16 in x 1 1 2 in stainless steel screws fasten the curved pieces of aluminum to the vertical pieces with the glass SR channel towards the inside of the tracks as shown in Fig 11 INSTALLATION INSTRUCTIONS 6 Insert the flat glass piece as shown in Fig 12 Using 3 9 mm x 9 5 mm 8 16 in x 3 8 in stainless steel screws attach the glass by installing two plastic stoppers as shown Install gaskets using a rubber mallet starting at the top Place the short gasket on the fixed glass panel with the flap facing towards the inside a Plastic stopper 4 1 Short gasket Insert glass Ce EEEE Fig 12 Inside 7 Fit the assembly into both fixed expanders as shown in Fig 13 Drill 3 2 mm 178 in holes for the self tapping screws following through the ore drilled holes on the expanders as shown in Fig 14 Secure with 3 9mm x 13 mm 3 16 in x 1 2 in stainless steel screws Place the screw caps to cover the screw heads INSTALLATION INSTRUCTIONS 8 Install the fixed roller assembly on the two top holes of each curved
8. o place making sure that the pipe fits into the collar and that the mortar squeezes up around the frame as shown in Fig 7 Check level to make sure that the unit is resting firmly on the floor ah hain ia Studs Mortar Pa Drywall l Raised flange 6 4 mm 0 25 in min E Clips d 7 lan a A aa hice oa WI Adjustable legs Lp ec o E F fe SERRET SELE E ani Adjustable legs Lock nuts Fig 7 INSTALLATION INSTRUCTIONS 10 Check that the drain pipe fits properly in the drain Secure the anchoring clips using 3 9 mm x 25 mm 3 16 in x 1 in stainless steel screws as shown in Fig 8 11 To ensure a watertight seal between the collar and the pipe tighten the drain ring using the wrench provided and a large flat screw driver Do not over tighten as the drain may warp or crack Insert the Strainer into position See Fig 9 12 Replace the water resistant drywall leaving a 6 4 mm 0 25 in gap between the top flange and the drywall Run a bead of silicone caulking around the joint between the top flange and the drywall 13 Install flooring up to 3 2 mm 1 8 in from the shower enclosure Run a bead of silicone between flooring and the shower enclosure INSTALLATION INSTRUCTIONS DOOR INSTALLATION 1 Using the fixed expander as a straight edge trace a line as in Fig 10 to mark the position of the two expanders so that they are 12 7 mm 0 5 in inside the edge of t
9. or damage caused by leaks due to freight damage Inspection prior to installation is the responsibility of the installer contractor or user Quality Craft will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing Quality Craft will not be held liable for damages resulting from the improper fit or installation of products not supplied by this company Quality Craft will not be held liable for loss of use of unit inconvenience costs incurred for labour materials removal and installation of replacement units or any other incidental or consequential damages ONE YEAR LIMITED WARRANTY Costs relating to obtaining access for repair or replacement are the responsibility of the user Under no circumstance shall Quality Craft or any of its representatives be held liable for injury to any persons or damage to any property Quality Craft s obligations shall be limited to the repair or replacement of a unit at our option that may prove by our sole examination to be defective under normal use and service during the warranty period The company may issue credit in the amount of the invoice value of the defective product or a percentage of it according to use in lieu of repair or replacement Quality Craft warranty is non transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the manufacturer s specifications This warrant
10. r coated aluminum frames provide a very durable finish e Precision rollers for ease of use BEFORE YOU START 1 Inspect your unit before proceeding Check the surface for any flaws or damage Your unit has been manufactured with a cast acrylic sheet providing an extremely durable surface Once you unpack your unit check for chips scratches cracks dents or scuff marks If any damage is noticed do not install Please read instructions carefully and keep for future reference Protect the entire surface during installation Make sure the floor structure is capable of supporting 100 Ibs 45 5 kgs per square foot 5 In all cases the total weight of the unit MUST rest on the floor No weight should be supported by the skirt or the tiling flange 6 All holes drilled into the unit must be done from the inside finished surface towards the outside rough surface and caulked very carefully to form a water tight barrier 7 Your installation must comply with all local plumbing codes Have a qualified tradesman do and or approve your plumbing installation WARNING Always wear safety goggles and gloves in order to avoid any personal injuries PARTS REQUIRED Pipe amp fittings according to Construction adhesive your installation requirements Silicone caulking small can of ABS pipe glue Ceramic tile or other Mortar or plaster waterproof wall finish TOOLS REQUIRED Hammer Screwdriver Drill Utility knife Measuring tape Ji
11. y shall not apply to any product that has been subject to accident alteration misuse or abnormal chemical conditions This warranty is made in lieu of all other warranties expressed or implied No other warranty expressed or implied is assumed or will be assumed Imported by QUALITY CRAFT Laval Quebec Canada H7C OA5 1 800 459 4409 www qualitycraft com
Download Pdf Manuals
Related Search