LED Vision Mesh Screen
Contents
1. Chapter 3 Installation Steps for LED Screen System LED Screen can function normally after finishing all these steps according to the following steps No 1 Installation for computer operation system Installation for Windows2000 or Windows XP operation system Windows XP operation system is strongly recommended No 2 Installation for LED Screen controlling card Neo Neon will provide a piece of main card for screen contained with PCI serial port and com port a piece of 4 LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited DVI serial port wire and com port wire Please refer to the following steps 1 Turn off the power supply and uncover the PC host computer insert the screen main card into the PCI slot of the host computer 2 Connect the PC com port and the luminance adjusting port of the main card with com port wire No 3 Installation for Software and Hardware of the Display Card 1 Installation for hardware of the display card We recommend to use the display card which contained with both VGA and DVI output port such as GeForce 7100GS recommend to use 2 Connect the DVI port of both the display card and the main card with DVI wire and then fasten the ire with bolts No 4 Hardware connection Connect the power supply of screen signal wire the signal wire for scanning board and screen signal wire for PC and scanning board please refer to Power and signal cable conn2. indication light of main card 4 Check the indicating light of the scanning board 5 Check the connect system refer to the accessory connect mode 6 Check the connection of DVI wire 7 Check the display card settings please refer to the PC software setting part Common Troubles Trouble Description Trouble Analysis Resolution The whole screen do not work The power supply does not function Increase power supply LED Control software does not turn on Setting control software Transmission cable does not connect well Reconnect transmission cable The display shows black color Re set the table board menu Module power supply does not connect well or voltage Make sure the voltage does not match above DC4 75 V The connect wire between module and scanning board is too long Cut off the cable wire Screen twinkle Data wire above the stated length or some trouble with cable wire Make sure the cable wire quality Data wire does not fasten stably Re insert the wire Control software are out of control Some trouble with LED unit module Check the module Display card setting incorrect Reinstall the Display card LED Control software is locked Open the control software Power supply will not increase when increasing power supply to the module Increase power supply o scanning board Addendum 4 ignal wire facture ommunic
3. LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited Neo Neon LED Vision Mesh Screen Operation Manual Neo Neon International Ltd He Shan Decorative Lighting Company Limited LED Display Engineering Department LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited Contents Chapter1 pecification and Function ParameterS ceccecseeseeeeeeneees 3 Chapeter2 tructure and Installation ccc cece ccc cceecccceccuucceeeeeaes 4 Chapeter3 Installation of Transmitting System ceeeeee ees 5 Chapeter4 esting Of LED SCree nisi ii a sccaiasaw neriwecmeay Setaciasd aver nacsnte eee 9 Chapeter5 Points for Attention when Using LED Screen 10 LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited Chapter 1 Specification and Function Parameters Thanks for choosing Neo Neon LS I 40 50VAL MESH RGB which is a kind of indoor substantial pixel LED display Through static scan the displayed image is Highly Fidel in quality and profuse in colors It is an excellent display choice for advertisement bank shopping center school restaurant amusement place and so on Module size 640mm x 640mm xX 65mm Signal Input 16P Double rank D SUB connecting piece only the protruding rank works Pitch 40mm Pixel composition 2R1G1B 485 oval LED M
4. ation wire connect scanning board and main board according to the following standards 1 Take off 3cm at the front end outer skin of the double twist cable with special double twist cable peeler or other tools 2 Match wire correctly Please make sure that wirel and wire 2 form a circle match wire3 and wire4 form a circle match wire5 and wire6 form la circle match wire7 and wire8 form a circle match At both ends of the wire same methods will be used The wire match is arranged in serration after certain color sequence Such as 1 white orange 2 orange 3 white green 4 green 5 13 LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited blue 6 white blue 7 white brown 8 brown After matching the wires trim the wires cut off the bare part of the double twist cable with only 15mm length left outsides Wire heads shall be trimmed to uniformity then put each wire of the double twist wire into to RJ45 connector lead the first lead shall be connected with orange whitish wire and the following in the same sequence After all the double twist wires have been placed tightly then press wire and let the wire to meet with the RJ45 connectors with RJ45 ire meet clamp On the other end the connection method is the same after all above action completed the RJ45 connectors shall be in niformity At test the connection with measuring equipment then the RJ45 connector is OK Signal wire conne
5. creen Neo Neon International Ltd He Shan Decorative Lighting Limited Multiple Monitors and RADEON 9200 SERIES Properties General Adapter Monitor Troubleshoot Color Management Displays ZAD Color FAH Options Z Rotation MA Overlay Z0 3D ZN VPU Recover Overlay Adjustments Brightness Contrast LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited Properties 1 Clone Mode Options You may need to restart your video application before changes to some of these settings can take effect For help with these Clone Mode Overlay options click the question mark in the top right comer of this dialog then click on a control Overlay Display Mode Standard C TheerMoa C Sameon Theater Mode Settings O f Addendum B GEFORCE Display setup 1 Press right bottom of MOUSE on the blank of table board enter into shortcut menu and choose Properties setting the screen resolution to 1024 x 768 pixels as follows 10 LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited Display Properties Themes Desktop Screen Saver Appearance Settings Drag the monitor icons to match the physical arrangement of your monitors Display 1 Default Monitor on Rage Mobility PCI Screen resolution Color quality Les Mo Medium 16 bit 1024 by 768 pixels ii nin nf Use this device as the p
6. ct screen module and scanning board module and module should be made as following steps tep 1 1 white orange 2 orange 3 white green 4 green 5 blue 6 white blue 7 white brown 8 brown tep2 1 brown 2 white brown 3 white blue 4 blue 5 green 6 white green 7 orange 8 white orange At the two ends the wire shall be arranged in different sequences If all above measures have been take problems still can not be solved please contact Neo Neon through phone call to get after sale service 14
7. ection diagram dwg IMPORTANT NOTICE THE GRAPHIC CARD WE USED MUST HAVE DVI AND VGA DOUBLE OPUTPUT INTERFACE No 5 PC Software Setup Connect the PC system and open up after finishing the hardware installation 1 Install display card drive software setup drive process beforehand which is very important for the latter setup 2 Install LED Studio8 software Serial No 88888 3 Set the property of PC display card enable the output of DVI port and the renovating frequency is 60Hz and hardware acceleration set as none Please refer to Addendum for detailed operation 4 Configure receiver Any details please refer to Configure receiver Doc 5 Setting the size and position of the screen any details please refer to LED Studio user s manual 5 LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited 7 Add display file any details please refer to LED Studio user s manual Screen can display picture normally after completing all those steps Addendum Addendum A ATI display card setup 1 Press right bottom of MOUSE on the blank of table board enter into shortcut menu and choose Properties setting the screen resolution to 1024 x 768 pixels as follows Display Properties Themes Desktop Screen Saver Appearance Settings Drag the monitor icons to match the physical arrangement of your monitors Display 1 Default Monitor on Rage Mob
8. ility PCI Screen resolution Color quality Less Moe Medium 16 bit 1024 by 768 pixels Use this device as the primary monitor Extend my Windows desktop onto this monitor Identify Troubleshoot 2 Press Advanced to setting the renovating frequency of the monitor to 60HZ as follows LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited Multiple Monitors and RADEON 9200 SERIES Properties Color Options Rotation Overlay 3D VPU Recover General Adapter Monitor Troubleshoot Color Management Displays Monitor type E Samsung SyncMaster sm95 Plug and Play Monitor Monitor settings Clearing this check box allows you to select display modes that this monitor cannot display correctly This may lead to an unusable display and or damaged hardware B Press display option turn FPD to green color as follows LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited Multiple Monitors and RADEON 9200 SERIES Properties Gil Color ZID Options ZID Rotation Zid Oveday ZD 30 ZID VPU Recover General Adapter Monitor Troubleshoot Color Management Displays 1024x768 60 Hz It is effective screen resolution 4 Press Recover option enter into clone mode options and the choose Same on all as follow LED Vision Mesh S
9. ission 1pc standard SUPER CAT IBDN for transmission Long distance transmission advanced data transmission technology using kilo mega data communication hips static electricity resistant lighting shock resistant support non relay long distance transmission max length of 130meter and 100 data recoverable Reliability 4 layer PCB and single chip super scale integrate circuit design promote system stability and reliability greatly Chapter 2 Structure and Installation Neo Neon usually packs 2pcs of Screen Module together once the following structural display module can be Seen after releasing package module size is 640 640mm Main fixture of a single LED Mesh Screen is omposed of A3 frame and LED Screen Panel which is mounted on the frame with screws 1pc frame can mount 16pcs of panel and 1pc of power supply the power supply will be fixed onto the strength board of the rame On each frame there are 12 M6 installation screws on each frame every 16pcs of frame shall be given la scanning board which will be fixed to the strengthening board of the frame with screws For the screen is a Specific feature thus we need to specify installation metal bracket according to panel and accessory Specification Metal bracket shall be prepared by customers themselves if there is no special declaration We strongly suggest customers to fix each mesh screen at the M6 holes noted in following diagram and lock screen onto the mounting brackets with screws
10. odule resolution length width 16 16 Density dot m2 625 Brightness cd m2 1300 Optimal viewing distance m 60 Module peak value power lt W 75 Module average power sW 40 Module weight kg 10 Scanning mode Static scan Viewing angle 120 60 horizontally and vertically Driven voltage V 4 5 5 5 Gray scale 256 levels respectively Frame change speed 260 frame second Control mode In step with the computer monitor Screen life 2100 000USD Blind spot rate lt 0 0002 Operating voltage AC220V415 47 64HZ Control distance m lt 130 Temperature environment 10 C 50 C Humidity environment 10 90 RH Product details are subject to change without notices Power supply shall be kept disconnected before installation is omplete Product Performance relatively better evenness mosaic decreased in some degree and a good lighting consistency Substantial pixels display thus excellent effect of displaying images characters and so on Alarge viewing angle 120 horizontally and vertically no distortion and color differentiation Quality whole process strict control from original material to finished product assure reliable high quality Service More consummate more comprehensive 3 LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited Performance Features DVI Display Card Compatible directly connectable with DVI port Single Cable Transm
11. rimary monitor Extend my Windows desktop onto this monitor Troubleshoot 2 Press Advanced to setting the refresh rate of the monitor to 60HZ as follows Plug and Play Monitor and NVIDIA GeForce 7100 Gs P Culu Mariayenerit GeFuice 7100 GS General Adapter Monitor Troubleshoot Monitor type FT Plug and Play Monitor Monitor settings Screen refresh rate 60 Hertz Hide modes that this monitor cannot display Clearing this check box allows you to select display modes that this monitor cannot display correctly Ths may lead to an unusable display and or damaged hardware LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited B Press GeForce 6200 Turbocache TM options setting the nView Choose nView Display Settings menu and press Clone on the options box as follows LSAS Al NVIDIA GeForce 7100 GS Bt em ewa sas ees megg E GeForce 7100 GS E GeForce 7100 GS lt pWiew Display Settings i Performance amp Quality Settings niew allows you to connect separate displays to a single graphics card Color Correction Video Overlay Settings Ful Screen Video View Display Mode z p Tools Primary display B Bend 557 h bbe Settings Secondary display m Philips 150P i Screen Resolutions amp Refresh Rates Desktop Management Menu Editing or WVIDIA JV Make thi
12. s the primary display F Disable auto panning on secondary device viewport lack Detect Displays Device Settings gt gt WE HiK WHAE hoose Application and Confirm Quit from Properties Selection No 2 Troubleshooting System checking method Please check system according to the following steps if the LED Screen can not work normally after finishing the connection and the power supply 1 Check the power supply system of the screen 2 Check the settings of LED control software 3 Check power supply unit screen module scanning board power supply indicator light Measure connector plugs of the relative circuit board is DC5V 0 3by multi meter 4 The Yellow Light on the scanning board will winkle under normal condition 5 The Red Light and the Yellow Light on the main card will last shining and twinkle respectively under normal condition If the Red Light does not work check the main card If the Yellow Light does not twinkle check the properties settings of main card or check the DVI wire 12 LED Vision Mesh Screen Neo Neon International Ltd He Shan Decorative Lighting Limited 6 Check LED screen module circuit according to the following steps 1 Check if the connect wires between unit screen module are connect according to the indication means on the unit board as the following picture 2 Check scanning board polarity and module connection as the following picture 3 Check the
Download Pdf Manuals
Related Search