User Manual Configuration Guide BASIC IP Pan
Contents
1. Network tab PASSWORD The Password tab will allow you to change the password note that User Names are never used The Setup Password by default is password If you change this MAKE SURE YOU WRITE IT DONE FOR FUTURE USE The Setup Password controls access to the setup html web page The Control Pasword is by default set to OFF This controls access to the main Pan Tilt control page BASIC P contro J Systems Inc Setu p Setup Password Re enter Setup Password Enable Control Password Control Password Re enter Control Password Page 12 RELAY 1 Clicking on the Relay 1 tab will bring up the following screen BASIC P comot J Systems Inc Setup Main Header Text Auto Refresh Page Duration Relay Description Display Relay Status Status ON Color Status ON Text Status OFF Color Status OFF Text ON OFF Buttons Button1 Label Button2 Label Pulse Button Pulse Button Label Pulse Duration The only setting on this page that you may want to adjust is the default Pulse Duration time The default is 1 second and the useful range is 0 1 to 1 5 seconds If you change the value click Submit to save it Relay 2 through Relay 4 are similar pages and again only Pulse Duration should be changed no other settings Clicking on the Control Page tab will take you back to the main BASIC IP PT Control System screen where you can control the PT Head2. 12VDC 5 Less than 1 5 W per Axis Maintenance Weatherproof Warranty BASIC IP Controller 9 500 in 7 2500 in 5 000 in Height Width Depth Materials Operating Temp Nickel Plated MIL C 26482 14 15 Pan 28 Deg Sec Tilt 8 Deg Sec 13 Ibs or less Pan 0 to 350 Deg Tilt 90 Deg Down to 30 Deg Up Light Grey similar to RAL 9018 lt 0 15 Deg None Required 30C to 70C No Heating or Cooling Required Regenerative IP68 2 Years Fiberglass Enclosure NEMA 4X Stainless Steel Mounting Brackets Connectors Waterproof RJ 45 Nickel Plated MIL C 26482 14 15 1 2 Liquid Tight Conduit Fitting Color Light Gray RAL 7036 Weight 3 Ibs Voltage 1 5 Watts Max 30C to 70C 2 Years Power Operating Temp Warranty 110 220 VAC 50 60 Hz TUV amp CE Page 16
3. Now select Use the following IP address Enter an IP address of 192 168 1 10 Enter a Subnet mask of 255 255 255 0 as shown below Internet Protocol TCP IP Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 168 1 100 Subnet mask 209 255 2007 0 Default gateway Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Altemate DNS server e a can Page 6 6 Click OK on this screen and then Close on the next screen Your computer is now on the same network as the IP PT controller s default network settings which will allow you to access the IP PT controller s configuration web pages To do this open the IE browser and type in the IP address of 192 168 1 2 and depress Enter The following screen will appear NOTE All center Pan Right indicators will show Stopped Pan Left Panning Lo oD atopa EOE Tilt Down NOTE The PT Head is shipped in its electrical center postion for both Pan and Tilt If you Pan Right twice during testing be sure to Pan Left twice to re center the head The same applies for Tilt At this point you should be able to use your computer
4. bracket should be attached to the mounting surface with suitable heavy duty hardware to assure a safe and secure installation Make sure the mounting surface is in good condition crumbling bricks or cracked concrete are not to be used The camera enclosure must also be given sufficient clearance to ensure that it does not hit any obstructions when rotated The motor and gearbox assemblies of the pan tilt head are designed to be stalled but continuous abuse will cause damage which is not covered under the warranty The pan tilt head and camera enclosure are very heavy and difficult to hold in one hand This equipment should be secured by a safety line to prevent it from falling on someone below if dropped by the installer Also once operational this equipment is subject to remote control and may be operated at any time while you are working on it Persons working on this equipment should take appropriate precautions to ensure that any unexpected movement does not occur as this could lead to finger hand injury or startle you causing you to fall or slip Always leave the power off to the control system and make sure someone is at the control who will make certain it is not activated without your express knowledge A pair of wireless radios are beneficial during installation and or maintenance so the installer and the operator can communicate directly Page 9 4 2 Mounting the Control Enclosure The control enclosure h
5. position Page 13 6 0 HTML API WEB PAGE INTERFACE Designing custom web pages is very simple assuming you have a basic knowledge of HTML pro gramming Please refer to the BASIC IP PT Control System API file located on the included CD y Soul apen S s ejani AC DC amaian gt gt Power Supply 3 vse t LYM SI AZ ANNO a Th Eib N E en v me A OPZ COL LANI OZS CLS IPON L a Adding 13mOg SW JS F Shielded CAT5 Cable IP Control Board AC Power Terminal Block PT Head Waterproof 1 2 Liquidtight Connector RJ45 Metal Fitting Connector Internal Layout View Page 14 7 0 TECHNICAL SUPPORT Technical support is available for no charge during normal business hours Business Hours Monday Friday 9 00AM to 4 00PM CST Contact Information Tele 630 627 3458 Fax 630 620 0960 E Mail info J Systems com Technical support will not be able to help you design custom web pages These are all questions best handled by a qualified web programmer 8 0 SUPPORT INFORMATION 8 1 Warranty Policy The PTZ Controller carries a 2 year manufacturer s warranty This warranty applies to failure of the product under normal operating conditions Situations that are not covered by this warranty include but are not limited to the following stresses e Lightning Strikes e Repeated Mechanical Stalling of the Head e Damage Due to Bullets or Other Projectiles e Cable Damage Due to Animals e Encasement in
6. s mouse and click on anyone of the GO buttons to make the pan tilt head move You will now want to set the IP address of the IP PTZ controller to your local area network so you can set your computer s network adapter back to where it was originally Enter the follow ing URL into your browser http 192 168 1 2 setup html and depress ENTER BASIC P control J Systems Inc Setup Network Password Relay 1 Relay Relay3 Relay 4 Control Page _ Model BASIC IP 1 Product Revision 2 5a Serial Number 00 0C C8 02 05 C7 For product support go to J Systems Inc Page 7 Click the Network tab You will be prompted for a UserName and Password This system does not accept a Username so tab over that field and enter the default password of password The following screen should apear in a second or two BASIC P cono J Systems Inc Setu p IP Address Netmask Broadcast Gateway TCP Port Modbus Port Speed Mode Change the IP Address Netmask and Gateway to match your local area network and click on Submit Leave Speed set to 10Mbps and Mode to Half Duplex After completing this reset your computer back to your original network settings and make sure you can still control the PT head by entering its IP address into your browser to obtain the screen shown on Pg 7 BASIC IP Controller Page 8 4 0 INSTALLATION At this point all the hardw
7. you your ladder or other equipment does NOT come in contact with these power lines Fatal shocks can occur If you are not qualified to install the wiring for this unit please secure qualified help Shown above is the JPTH 13 pan tit head to the left the special 7 foot interconnect cable and NEMA 4X control enclosure to the right The connectors on the bottom of the control enclosure are from left to right the pan tit head connector waterproof RJ45 jack and 1 2 liquid tight fitting for AC power Page 3 2 1 Connecting the Pan Tilt Head Once all of the parts have been identified proceed to connect the supplied special high flexibility cable to the Military style connector on the rear of the pan tilt head The other end of the cable connects to the pan tilt control enclosure Make sure the Military style connector shell is fully engaged and locked in place This cable is specially designed to be utilized where constant flexing is required Additionally the cable has been selected to maintain its flexibility at extremely cold temperatures Do not replace this cable with ordinary cable If longer sections of cable are required please consult the factory for pricing and delivery the maximum length is 20ft CAUTION Always exercise extreme caution when working near power lines or live circuits to ensure that you your ladder or other equipment does NOT come in contact with these power lines Fatal shocks can occur I
8. IA j systems Engineered Surveillance Solutions User Manual Configuration Guide for the BASIC IP Pan Tilt Control System Version 1 0 December 2007 Copyright 2007 2009 J Systems Inc 1 South 678 School Ave Lombard IL 60148 Tel 630 627 3458 Fax 630 620 0960 E Mail info J Systems com 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 TABLE OF CONTENTS DU SOIC TONY aasesncerensea vasrsnoesenctemnderseamquuateneasiauiosuqaneteenedeiaahataoniaceendiugnesce 1 1 Concept israe E EAE AE E 1 2 Vnpackih gesseram insa aE aE 1 3 System COmMponEN iS scissioni aaia 1 4 Before You Start sssavimirehosnkianaa ai i NEE Initial Setup ssisissescsvvesssuyvenviscvvdessensvenveseutexvercauensdsrss vionsdes A EREE 2 1 Connecting the PT Head ssccicccrccisrannavseuneneteaanmnseagsnmeimeacelansyaoase 2 2 Connecting AC POW sicissctsevisnauctewsbatcenaieccincammanveaccunictuseans COMNg raUO M sss e a ENA NASTANAUIOMN iccictsssiccnntetesaxsuabinneavagesdadadoagacsnaimnntantaveteaniarantscunidnteantencianneds 4 1 Mounting the Pan Tilt Head suciissnsurnenpnserscnessanatecvabenuaswmisenenes 4 2 Mounting the Control Enclosure 2 cccccsesceccnteeenereeeneeees 4 3 Adjusting Pan Tilt Head Limit Switches 00 eeeeeeee Setup Interface sssrinin aE aE EAEE AEAEE E a ERE HTMLAPI Web Page IMGriace a iiiecciiccciinsiinnasennnnsmcestanidstweneamvdannnned Technical SUpport vicisiviccecvitevssetevswsavesevsssesvneevverdcaveveeveetevertusveu
9. Ice e Applied Voltage Greater Than 264VAC e Overloading the PTZ Head e Attempted Repair By An Unauthorized Individual Any other damage that in J Systems Inc s opinion have been caused as a result of abnormal or abusive use will also void the warranty Page 15 To return a unit for repair an RMA Return Material Authorization must be obtained prior to sending the unit back Units received without a prior RMA being issued will be returned to the sender unopened When returning a unit for warranty or out of warranty repair the cost of shipping back to the factory will be borne by the customer Warranty repaired items will be returned to the cus tomer postage free Call 630 627 3458 during normal business hours to obtain an RMA 8 2 Specifications The following are general specifications for the IP PT Control System These specifications are subject to change at any time Detailed specifications are found on the IP PT Control System literature piece located on the CD Height Width Depth Materials Paint Mounting Plate Weight Voltage Power Pan Tilt Head 5 800 in Connector 6 210 in Speed 5 08 in with connector Machined Alu w Stainless Fasteners Capacity Anodized Alu Mounting Ring Rotation Limits Polymer Bearings for Quiet Operation Color Backlash Ball Bearings on Major Axes Powder Coat Width 5 820 in Depth 4 730 in Slots 1 4 in Hardware or Smaller 5 Ibs Braking
10. Limit Switch Drive the pan tilt head to the upper most position required camera would be pointed upward Slide the rear actuator until it engages and trips the switch lever arm This is best done using a flat blade screwdriver keep your fingers out of this area This limit is now set Drive the unit to the lowest point required camera pointed downward and slide the front actuator until it engages and trips the switch lever arm This limit is now set Drive the pan tilt unit to the extreme limits of travel in both directions and check operation for the limit switches Re adjust if necessary Photo shows tilt actuator tripping the switch lever arm The IP PT Control System installation and test should now be complete Page 11 5 0 SETUP INTERFACE If changes are requred to the BASIC IP PT control s default setting they can be made by accessing the built in web intreface of the control This is accomplished by entering the IP ad dress of the control as follows http 192 168 1 2 setup html Note the controls IP address may have been changed during Configuration Once entered the following screen will appear BASIC P cont J Systems Inc Setu p Model BASIC IP 1 Product Revision 2 5a Serial Number 00 0C C8 02 05 C7 For product support go to J Systems Inc In the Configuratino section of this manual you saw how to change the IP address of the con troller that was done by selecting the
11. TION The following paragraphs will lead you through the setup and configuration of the IP PT control system 3 1 Install Setup and Testing The following sections will cover initial configuration of the controller s software and testing It is recommended that all this configuration be done BEFORE the PT head and enclosure are mounted outside 3 1 1 Initial Power Up and Testing At this point the following items should be connected The pan tilt head should be connected to the IP PT control enclosure with the special 7 ft cable It would be beneficial to secure the pan tilt head to the mount it will be ultimately attached to This will allow the head to be fully operational during initial setup testing e Connect a CAT5 cable to the RJ45 jack on the bottom of the IP PT control enclosure The other end goes to your computer eAC power should also now be applied Here are the steps you will follow to gain access to the IP PT controller e 1 Set your computer s network adapter IP address to 192 168 1 100 To Network accomplish this in Windows XP or 2000 click on Start Settings then Connections Cntrol Panel Once inside Control Panel double click on the Network Connections icon as shown to the left 3 i 2 Once you have clicked on Network Connections you will see the Local rea icon to the left Connection 3 Double click on the Local Area Connection icon you will see the following screen 4 LAN Connect
12. are should have been tested and proved to be functional IMPORTANT Prior to final installation you should learn how to adjust the PT head mechanical limit switches while the PT head is within reach Final adjustments can of course be done after the PT head is mounted Please refer to Para 4 3 before mounting the PT head Mount your camera enclosure to the top of the PT Head 4 1 Mounting the Pan Tilt Head The unit has a base which requires 3 x 1 4 20 bolts and washers supplied in a 120 degree bolt hole pattern When mounting the head please remember that a fully loaded pan tilt camera enclosure assembly may weigh considerably more than 13 Ibs The pan tilt head assembly is electrically and mechanically centered before being shipped and the connector is located at what we define to be the rear of the pan tilt head Substantial mounting brackets strong and rigid will be required to handle this mechanical load and allow for adverse weather conditions Bad weather can result in ice and snow build up as well as high wind loading Consult the factory if you are unsure as to what type of bracket to use or to purchase factory available brackets Stability and rigidness are important as the pan tilt head with camera and enclosure exerts inertia when it starts and stops If the mounting mechanism is not rigid enough some back and forth motion may be seen when the head starts and stops Once the camera location has been determined the mounting
13. as been supplied with rugged stainless steel mounting brack ets These brackets can be used to mount the control enclosure to a flat wall a small mast or larger pole such as a wooden telephone pole or metal light pole The brackets accept lag screws or bolts stainless steel band clamps straps and U bolts None of this hardware has been supplied as each installation s mounting requirements are different CAUTION Always exercise extreme caution when working near power lines or live circuits to ensure that you your ladder or other equipment does NOT come in contact with these power lines Fatal shocks can occur If you are not qualified to install the wiring for this unit please secure qualified help AC power should be connected as described in Para 2 2 Again only liquid tight con duit that supplies an earth ground should be used If you have purchased a DC powered system then a 1 2 plastic bulkhead fitting will be supplied which can replace the 1 2 metal liquid tight fitting if you like Also your enclo sure will have a small copper ground lug on the side of the enclosure This ground lug MUST be tied to earth ground following NEC code You have also been supplied with the mating half of the water proof RJ45 connector Follow the supplied directions for inserting your CAT5 cable into this connector Page 10 4 3 Adjusting the Pan Tilt Head Limit Switches Once the system is operational and the pan tilt hea
14. d can be panned and tilted it is important to set the mechanical limit switches that control he absolute pan and tilt limits For the purposes of identification the rear of the pan tilt head is defined as the connector location When viewed from the top clockwise movement is Pan Right and counter clockwise movement is Pan Left The head contains internal pan and tilt limit switched that are controlled by shaft mounted actuators 2 per shaft As the head rotates one actuator trips an externally mounted switch level arm which causes the pan tilt head to stop moving in that direction This system provides an accurate and simple method of applying pan and tilt limit stops It is not necessary to power down or gain access to the inside of the unit to set the limit switches Setting the Pan Limit Switch Drive the pan tilt head to the left hand position you require Slide the top actuator until it engages and trips the switch lever arm This is best done using a flat blade screwdriver keep your fingers out of this area This limit is now set In a similar manner drive the unit to the extreme right hand position required and slide the bottom actuator until it engages and trips the switch lever arm This limit is now set Drive the pan tilt unit to the extreme limits of travel in both directions and check operation for the limit switches Re adjust if necessary Photo shows two limit switch actuators mounted on the pan shaft Setting the Tilt
15. done by those that are qualified to perform the needed work 1 1 Concept The IP PT system is an IP based position control system It was specifically designed to allow the positioning of a remote IP camera across IP based networks wired or wireless including cellular Further all the equipment that makes up this system has been designed for harsh duty environments NEMA 4X enclosure 30C to 70C operation The IP PT system was designed to provide BASIC positional control across any IP based network The IP PT system s built in web browser interface is simple allowing for left right and up down control Custom web pages can easily be designed to display both an IP camera s live video as well as graphical controls which allow simple pan and tilt camera movement Examples of this type of web page are incluced on the CD The IP PT system provides all the necessary power for the control board and pan tilt head using a built in 12VDC 15W encapsulated power supply that is both TUV approved and CE marked As the pan tilt head operates from 12VDC an optional 12VDC or 24VDC version of the IP PT system is available which uses a 15 watt 10 to 40VDC DC DC converter which provides stable 12VDC for the pan tilt head This option is ideal for both mobile and solar powered applications A special high flexibility cable flexible down to 40C is provided to connect the pan tilt head to the control enclosure A waterproof RJ45 jack is also provided f
16. evnsennas SUPPOFE INFORMAULON vas ciesseivnsiivesisaitisdenstsaviadebiasteedwuelasehude aE 8 1 Warranty POMC x cissiincntutrsvitnccssesnaheneniaustascatcandasdasumtesntarentauiatnne 8 2 Specification S eneen uate ETRS eA DISCLAIMER J Systems Inc makes no warranties either express or implied regarding the enclosed IP Pan Tilt Controller System its merchantability or its fitness for any particular purpose Further J Systems Inc assumes no responsibility for any damages losses or claims resulting from the use or misuse of this equipment The extent of any liability is expressly limited to the original purchase price of the equipment oOo o o o A A OO N N N ee H i l a A O a oa Oo A N gt 1 0 INTRODUCTION Congratulations on your purchase of the BASIC IP Pan Tilt Control System IP PT This unique harsh environment system was built to the highest quality standards and with proper use and installation will provide many years of service It is STRONGLY recommend that you read this manual carefully and completely to fully understand the capabilities of this system before attempting installation CAUTION The installation and setup of the IP PT system involves a number of potentially dangerous operations such as climbing using man lifts workingwith120o0r220VAC power handlingheavyitemsaboveground and working with a device that can be remotely controlled by others The installation of the IP PT system should ONLY be
17. f you are not qualified to install the wiring for this unit please secure qualified help 2 2 Connecting AC Power The PTZ controller is supplied with a metal 1 2 liquid tight fitting A special grounding ring has been attached to this fitting on the inside of the fiberglass enclosure This ground ring is connected to the back panel and provides the necessary ground for the entire system AC power should be run to the IP PT controller from an appropriate disconnect which includes a ground fault interrupt function Local electrical codes should be followed for outdoor AC wiring The cover of the IP PT control enclosure will have to be opened to make all internal connections The AC power fitting provided is for 1 2 liquid tight flexible steel conduit DO NOT USE PLASTIC LIQUID TIGHT CONDUIT WHICH HAS NO STEEL GROUNDING ELEMENT Proper grounding of the liquid tight flexible steel conduit at the power source must be accomplished in accordance with local electrical codes Failure to provide an adequate ground may result in diminished surge and lighting protection for the PTZ controller AC power is brought to the enclosure and terminated in the 3 position terminal block directly adjacent to the 1 2 liquid tight fitting The Black wire is Phase A or the hot leg The White wire is Neutral The Green wire is earth ground NOTE 10 40VDC powered versions of the IP PT system are available consult factory 3 0 CONFIGURA
18. ion Properties pe z General Authentication Advanced Connect using E Marvell Yukon 88E8053 PCI E Gigabi This connection uses the following items Client for Microsoft Networks B File and Printer Sharing for Microsoft Networks M 3 Network Monitor Driver Internet Protocol TCP IP Description Transmission Control Protocol Intermet Protocol The default wide area network protocol that provides communication across diverse interconnected networks C Show icon in notification area when connected Notify me when this connection has limited or no connectivity Page 5 5 Select Internet Protocol TCP IP and click on the Properties button Once you have done this you will see the next screen shown below NOTE if your computer has been configured with manually entered static IP address be sure to document this before you change it Internet Protocol TCP IP Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP addre Subnet mask Default gateway Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server
19. or connection to a LAN wireless radio or cellular router to allow TCP IP connection to the controller board The standard main power connection is through a 1 2 metal liquid tight fitting on the bottom of the NEMA 4X fiberglass enclosure The enclosure is furnished with universal stainless steel mounting brackets Finally the IP PT system is completely Web browser based allowing easy setup and configuration A simple HTML based API is built in which can be incorporated into any web page to make the controller s functions appear as if they have been custom designed for your specific web site Page 1 1 2 Unpacking The IP PT system has been carefully packaged to provide protection during shipment We suggest that you keep this packaging in the event that factory warranty service is ever required Please inspect and note the condition of the shipping containers before opening them Punctures tears and crushed ends are indications of abusive treatment by the shipping company and should be photographed and reported to the carrier in the event any damage is found inside to file a claim 1 3 System Components Your IP PT system may have shipped to you in more than one carton depending upon the items purchased Standard Items Qty 1 JPTH 13 Pan Tilt Head Qty 1 Fiberglass NEMA 4X Control Enclosure Qty 1 7ft Highly Flexible Interconnect Cable with Military Style Connectors Qty 2 Stainless Steel Universal Mounting Bracke
20. ts for the Control Enclosure Qty 1 RJ45 Quick Connect Mating Connector Qty 1 User Manual Configuration Guide CD Optional Items Wall Mount with 3 Pedestal for JPTH 13 Pan Tilt Head Corner Mount for Wall Mount above Pole Mount for Wall Mount above 1 4 Before You Start A successful installation assumes you have the necessary skills or qualified support personnel to accomplish the following tasks e Mount the JPTH 13 pan tilt head and arm to a structure or a mast e Ability to crimp and test RJ45 modular jacks to the end of a CAT5 cable e A method to test CAT5 cables e Ability to wire 120 220VAC power to the IP PT System control enclosure per local electrical code e Ability to provide a good earth ground via the 1 2 liquid tight fitting or ground lug on the side of the enclosure for DC powered systems CAUTION Always exercise extreme caution when working near power lines or live circuits to ensure that you your ladder or other equipment does NOT come in contact with the power lines Fatal shocks can occur Page 2 2 0 INITIAL SETUP Before mounting all your equipment it is highly recommended that the entire system be setup and tested completely before pieces of equipment are mounted in difficult to reach locations This initial setup and test step will help to ensure a smooth trouble free installation CAUTION Always exercise extreme caution when working near power lines or live circuits to ensure that
Download Pdf Manuals
Related Search