TELEPOOL Professional
Contents
1. 00 30 PHASE 2 00 60 PHASE 3 00 20 12 S T Rxmax mV On the right top corner the start time of phase 1 is showed The blinking arrow gt indicates that the C dosage is active The Chlorine measurement will be executed according to set up step The Phase 1 terminates if the Redox reaches the threshold of Rx end chlorine or if the time of Chlorination is exceeded The bar graph indicates the effective dosage in phase 1 in analogical mode 2 Phase 2 The Relays 51 S2 and 54 are deactivated The blinking arrow gt indicates that this phase is active The CI2 measurements are executed according to the set up step Phase 2 terminates when the T FASE2 time is over 3 Phase 3 The Relay S4 is activated The following outline represents display 2 during the 3rd phase BREAKPOINT 21702707 DOS T0 PHASE 1 KA Xx Pi x ILLE 00 30 PHASE 2 kk kk ke k ke k kk kk KK KK KK KKK KEK 00 60 PHASE 3 gt 00 30 C12 Rxmax The blinking arrow gt indicates that the dosage C is active The CI2 measurements are continuously executed the set up step is not considered Phase 3 has two possible ways of execution The duration of the phase of De chlorination is proportional to the effective time of dosage of the chlorination phase The logic is T 0051 EFFis the effective time of dosage executed in phase of Chlorination DOS1 EFF T P2. By setting up it will use a filling storage When the archive is full the instrument will stop the recording and it will appear on the display USED Percentage of used memory RESET This function allows to delete all the stored data 5 5 Modify Password New Password In this menu is possible to modify the system password Once confirmed with the new password will be memorized and from now on to enter the program you will need the new password 0O SERVICE This menu is used to manually verify external operator navigations and to verify the correct operation of the instrument We advise the use of this function only by expert staff 5 6 Relay 51 Cl E Clicking repetitively on is possible to switch ON and OFF the Relay S1 52 Cl 20 7 32 TELEPOOL PROFESSIONAL Z ENGINEERING Clicking repetitively on it is possible to switch ON and OFF the Relay S2 53 pH Clicking repetitively on itis possible to switch ON and OFF the relay 53 54 CI P Clicking repetitively on itis possible to switch ON and OFF the Relay S4 Alarm T Clicking repetitively on itis possible to switch ON and OFF the alarm Relay ATTENTION The relays set up on ON will stay this way until OFF is selected and the menu Relay exited 5 7 ENTRIES Conductivity lemperature Dosages CELL The value indicates the state of the cell In normal condition the value stays between 700 and 800 The lowest value
3. 40 C Working Temperature from 10 C to 45 C 12732 TELEPOOL PROFESSIONAL AL ENGINEERING EQUIPMENT CHARACTERISTICS TECHN CAL MEASURE CHARACTERISTICS Precision 2 F S FREE CHLORINE SSS repeatability 98 een Nr 3 with relais exit Nr 2 in exchange and Nr 1 ON OFF charge max 1 230Vac resistive with varistors of suppression disturbs COMBINE CHLORINE optional Type of measure Pick of absorption Metodic used Resolution Precision repeatability PH Range of measure 00 00 14 00 pH Precision repeatability Entry Impedance Polarization np Nr 1 with exit relay in exchange charge max 1A 230Vac resistive with varistors of disturbs suppression O R P REDOX POTENTIAL Type of measure Precision repeatability Entry Impedance 13 32 TELEPOOL PROFESSIONAL AL ENGINEERING CONDUCTIVITY repeatability c TEMPERATURE HARDWARE C ARACTERISTICS clock Frequence of 32 768 Khz Nr 2 In Exchange for Free Chlorine measure Cloration Nr 1 ON OFF for Free Chlorine measure Decloration Dosing Relais si Nr 1 in exchangenfor pH measure charge max 1A 230Vac resistive with varistors of disturbs suppression Nr 1 of exchange Comulative for all the alarm charge max 1A 230Vac resistive with varistors of disturbs suppression Qualification Dosing Nr 1 Active Digital Entry Fast multipolar Connectors with IP67protection Nr 1 3 PE Male Alimentation Alarm relais Nr 1 6 M
4. Professional analyser multiparameter Model E conforme alle seguenti direttive CE 73 23CE 89 336CE 92 31CE 93 68CE come modificate e recepite dalla legislatura italiana The machinery meets the requirements set bu the folloging EEC Directives Directives 73 23CE 89 336CE 92 31CE 93 68CE as amended and implemended under italian law oono state applicate le seguenti Norme Nazionali che traspongono le Norme Armonizzate CE The following national standards and technical specifications conforming to EEC Harmonized Regulations were folllowed EN 61000 6 4 2002 10 EN 61000 6 2 2002 02 EN 55011 1999 05 CEI EN 61000 3 2 2002 04 CEI EN 61000 3 3 1977 06 EN 61010 1 2001 11 Castelnuovo Rangone 20 01 2006 ENGINEERING CORPORATION 5 r l mrunistratore Responsabile ENGINEERING Corporation srl Barani Dr Corrado 9132 TELEPOOL PROFESSIONAL Z ENGINEERING TELEPOOL INSTALLATION MANUAL 35 X o Mb em x Parte superiore utilizzare n 2 tasselli a gancio corto Parte inferiore utilizzare n 1 tassello e relativa vite Pavimento wall has to be well smooth to allow the perfect adhesion of the various parts of the equipment There hasn t to be water or possible spray coming from closed zones Use as power supply a tension among 85 265 Vac 50 60Hz without interference Avoid absolutely reconstructed connection for example with the aid of transfo
5. the right of possible changes without warning COPYRIGHT Every reproduction or copy of this manual is forbidden even if partial and through any procedure AUTHORISED TECHNICAL ASSISTANCE CENTERS ENGINEERING CORPORATION SRL Via S Allende 9 41051 Castelnuovo R MO ITALY 2432 TELEPOOL PROFESSIONAL Z ENGINEERING GENERALITY INFORMATION ON THE MANUAL This document contains information of reserved ownership They can be subject to changes and updating without warning Chronology of press Before edition Telepool Professional For version b December 0 1 th 2006 Second edition Telepool Professional For version b September 0 2 th 2007 Third edition Telepool Professional For version b December 0 3 th 2007 Fourth edition Telepool Professional For version b February 0 4 th 2008 The manual present is integral part of the tool During the first installation of the instrument the operator has to effectuate an accurate control of the content of the manual with the purpose to verify the integrity and the completeness of it In the case it resulted ruined incomplete or inadequate please contacted the firm ENGINEERING CORPORATION srl to quickly replace the non conforming manual The official versions of the manual of which the firm ENGINEERING CORPORATION srl is directly responsible they are those in Italian language The firm ENGINEERING CORPORATION srl is not taken on any responsibility 1n comparison to possible translations in d
6. 1 THRESHOLD EE 24 3 0 SECTION REDOX I U 25 TRE HOL 25 Xe YII VIC MEE 25 4 0 CONDUCTIBILITIES scere rennen nnne nennt nnn nnne 25 lnbsue p MEE 25 LP XeT YR TT VIO RM 26 5 0 TEMPERATURE cssesessescsssscsssecaeseesesecaesecausecausecausecausesauesaeseeausesansesanes 26 SA OFFSBIS 26 6 0 VISUALIZE DATA I nnne nennen Ta 26 7 0 COMMON IT RM 27 7 1 CLOCK II I I I dd bu tue IE m ED DUE 27 7 2 DATA Sci REM 27 7 3 Y RR 27 115 ET 28 7 5 CHANGE PASSWORD ceres enne nennen nennt I tnnt nsns 28 Ao E 28 L T PLAY S 29 8 3 INFOS MEM 30 Em 30 MAINTENANCE MNANUAL I tn nnne 31 2432 TELEPOOL PROFESSIONAL Z ENGINEERING GENERAL CLAUSES Although the maximum care has been set in the elaboration of this document ENGINEERING CORPORATION cannot guarantee the exactness of all the information here contained and it cannot be held responsible neither of the errors that this could involve neither of the damages that could result from the use or from the application of it The material products the software and the services introduced in this document can be updated in as for characteristics of presentation of operation the firm ENGINEERING CORPORATION reserves him
7. HASE 1 Subsequently the time T k T is calculated and T is estimated If T is inferior to 15 minutes a C dosage is executed within a time T on the contrary the dosage is executed based on the CI2 measure and the threshold S4 In this second case the CI2 measures are considered When a sequence of 5 not increasing measures is found and all of them higher than 0 30 ppm the free chlorine measure is considered valid Then the Cl2 measured is compared to the threshold S4 As soon as the chlorine decreases under the S4 threshold the phase of De chlorination terminates When the Breakpoint phase finishes it automatically enter in DESABLED and won t be executed again until the setup is re enabled On the screen appears the picture of the last executed Breakpoint 22132 TELEPOOL PROFESSIONAL Z ENGINEERING The Cl2 value on the bottom indicates the value of the last measure executed during the Breakpoint The Redox value also at the bottom of the screen indicates the highest level reached during the Breakpoint 1 2 Calibration This phase is the function of alignment of the Free Chlorine to a fixed value The instrument after having asked confirmation to proceed with the calibration will carry out a Free Chlorine analysis At the of analysis two values will appear on the display Free Chlorine Value with the K factor of reference K factor 4 25 Free Chlorine Value with the K factor of the analysis Using the
8. OLD T FINISH T PHASE1 T PHASE2 T If the Finish time is reached the Breakpoint will be permanently cancelled If the set Start time is higher than the Finish time the machine assumes that the Finish time is for the next day For example Start 2 23 00 and Finish 2 03 00 the Breakpoint starts at 23 00 today and finishes the tomorrow at 03 00 The instrument won t allow to set up a duration between Start and Finish inferior to the sum of the durations set for the three phases RX END CHLORINE Threshold of Redox potential in which the first phase of chlorination terminates in any case The phase of Chlorination can finish either at the expiring of the time set up on Chlorination or at the attainment of the Redox threshold set up here CHLORINATION First Phase of the Breakpoint in which the S1 and S2 Relays are switched ON for the maximum time set up Attention The phase of Chlorination can finish before the set up time if the Redox threshold previously set up is reached WAITING Second Phase of the Breakpoint in which the S1 and S2 Relays are switched OFF for the set up time DE CHLORINATION Third Phase of the Breakpoint in which the S4 Relay is switched ON and the de chlorination is monitored Here a maximum time for the de chlorination is set up Exceeded this time the 3 phase terminates showing an anomaly on the display and the instrument attends confirmation from the operator in o
9. POOL PROFESSIONAL Z ENGINEERING Parameter used to align the temperature reading to a know instrument 5 0 VISUALIZE DATA In this section you will be able to graphically examine at fixed period of time the trend of all the parameters measured by the instrument Visualize gt gt gt Interval 2 H Date 01701706 VISUALIZE By clicking on P You enter the graphic visualizing according to the following parameters It is possible to scroll the measures achieve using the arrows It is possible to change the visualized option by clicking on 3 The sequence is free chlorine combined chlorine pH Redox conductivity and temperature INTERVAL Interval of time for the visualisation of the data Can be set every 2h 6h or 24 h DATE Set up the starting date for the visualisation of the data 6 0DATA In this section is possible to set up all the system parameters 5 1 Clock Day Month Year Hour Minute 21 1 32 TELEPOOL PROFESSIONAL Z ENGINEERING Day and hour set up 5 2 System Data Language English Address 1 Baud Rate 9600 Display Normal Contrast 45 5 Language Setting up of the language Italian English French or Spanish Address Numeric address between 1 and 255 used for the instrument connection in BUS RS485 Baud Rate Setting up of the speed of the serial communication host port with protocol MOD BUS RTU It can be 9600 19200 or 38400 Display setting up of the
10. S4 will be closed and remained closed until the value of the chlorine will not come down under the threshold of S4 TIMEOUT ALARM Security Parameter concerning the dosage of the Chlorine Section If set up to 0 min the function is disabled If whichever of the three Chlorine threshold 51 S2 or 54 remains active for a greater time of the set up time the instrument will stop all the dosages and activate the alarm Relay On the monitor will appear 19 32 TELEPOOL PROFESSIONAL Z ENGINEERING This alarm will be able to re enter automatically the instrument will carry out the analysis of the values when the Chlorine value will deactivate the Timeout threshold the dosages will resume their normal operation and the Relay of the alarm will be deactivated This security Parameter allows the instrument to control the dosage conducted externally and the reliability of the chlorine measures 1 2 BREAKPOINT State Disabled Rx end chlorine 700 mV CHhLorrnsatorori 00 HH MM Waiting 00 HH MM De chlorination 00 HH MM Stare 00 HH MM Finish 00 HH MM The Breakpoint function can be periodically used to carry out a shock treatment of the pool water in order to eliminate most of the organic substances present in the water therefore reducing the combined chlorine value The Breakpoint function is constituted by three phases the first one is the Chlorination the second one is the Waiting and the last one is De chlorina
11. TELEPOOL PROFESSIONAL AQ ENGINEERING ENGINEERING TECHNICAL BOOK INSTALLATION SET UP MAINTENANCE 1 1 ver b 05 del 03 2008 Telepool ver 2 5 Via S Allende 9 41051 Castelnuovo R MO Italy E Tel 0039 059 537765 fax 0039 059 5332058 ap A info engineeringcorporation it www engineeringcorporation it Azienda Certificata UN EN ISO 9001 CERT N 4247 1 32 TELEPOOL PROFESSIONAL Z ENGINEERING GENERAL CLAUSES eres ennt nnne nenne I aaa 3 GENERALITY M 4 CONVENTIONS CM 5 6 rene enn 8 DECLARATION e ARR 9 MANUAL OF INSTALLATION esee 10 CHARACTERISTICS TOOL I nennen enne nnne tnter tnter retains 13 CHARACTERISTICS TECHNICAL MEASURES eere 13 CHARACTERISTICS HARDWARE I I enne nnne 14 CHARACTERISTICS SOFTWARE eere nennen nennen nnne nnne 15 DESCRIPTION SOFTWARE TELEPOOL VER 2 3 16 DESCRIPTION RUNSCREEN I I I a N 16 FUNCTION B zz 8 RR 17 MAIN MENU 5 18 DESCRIPTIONIMENU ue since dixe pe te I I un a I qe Met 19 1 0 SECTION CHLORINE eere I nnne nnne nnne netten nennen 19 IEBniiel EM 19 A LA IN 20 1 3 CALIBRATION RE 23 1 4 SETUP JP UT YR RE 23 2 0 SECTION EE 24 2
12. afety Visualizzation 15 32 TELEPOOL PROFESSIONAL Z ENGINEERING SOFWARE DESCRIPTION TELEPOOL VER 2 5 RUN SCREEN DESCRIPTION VISUALISATION OF Free chlorine measure Combine chlorine measure Optional pH measure Rx measure Conductivity measure Temperature measure Analysys phases Exit Relais Status System Date Hour Graphics Alarms for lack of reagent Time Out Cl2 and pH Data Logger Full Analysys phase Chlorine Methodic VISUALISATION OF gt Last 13 created alarmi gt Analysys phase Chlorine Methodic 54 u Tec TOUT Contact Assistance 1 LET W NY UN VN N N NN N VISUALIZZAZIONE DI preste FASE 1 Last State phase of Breackpoint 01 00 Minimum Value of reached chlorine on phase 3 Maximum Pick of reached ORP FASE 2 Date Hour last Breakpoint AZAA FASE 5 If the breakpoint Phase is not activated the shown data 91 08 refer to last made phase of breakpoint Cle 0 00 900 Visualised ICONS HOU eee Timeout Chlorine Section BEI o Finished Reagent o Peristeltic tube broken aom Timeout pH section Contact System Mistake A ssistaticel Please Contact Assistance FATAL ERROR CONTACT AN ASSISTANCE E i a Fatal Error Equipment Blocked Contact Assistance mj i Archive Memory full 39 59 536502 16 32 TELEPOOL PROFESSIONAL Z ENGINEERING FUNCTION BUTTON Confirm data at the switch on kept pushed allows
13. ale Relais Exit Nr 1 6 Female Digital Entry Serial Host Alimentation Absorbption Weight 14 32 TELEPOOL PROFESSIONAL AL ENGINEERING SOFTWARE CHARACTERISTICS C Respect and equipment regulations Safety concerning Feeding Anomalies external and internal Equipment Measures Wrong Calibrations Equipment Damage RUNScreen with the last 13 alarms shown available in each moments Each alarms is shown on the display and will activate the ralais of alarm Created Alarms Lack of analysys water Dirty Cell Alarms available Broken Cell Burnt projector Lack of Reagent Timeout Chlorine Timeout pH Error 21 The use of a graphic display 240x128 allows a intuitive and immediate graphic representation of the measures of alarm icons and main menu so to let the management and the equipment regulation Easy and fast to each operator Internal Data logger on Flash memory Memorisation of all the analogic Archive measures Free Chlorine Combine Chlorine pH Redox Conductivity and Temperature with changeable recording step from 1 to 60 minutes Possibility to watch directly the instrument the graphic of all the measures Choosing step of time of 2 6 or 24 hours 5 Instrument Setup protected with password to avoid damage from un assword authorised person Language Choose from Italian default English French Spanish German Protocol MOD BUS RTU with dedicated functions to download the archive S
14. arrows it will be possible to modify the second value of free chlorine and once set up click to confirm Usually the two values are closed to each other within a range If this is not the case we recommend verifying the correct kinetics of the instrument before confirming the new calibration in order to avoid anomalous calibrations In any case the Telepool Professional will check the K factor every time a Free chlorine calibration is executed The instrument will give an error and won t execute the calibration if the K factor equals values exceeding the parameters set up 1 3 Setup Analysis Interval Initial Wash Injection DPD1 2 Reaction C12 otep Cl comb Injection DPD3 Reaction Cl comb In this menu the timing of the Free and Combined Chlorine processes are set up If tampered by unauthorised staff these parameters may compromise the measures of the instrument Therefore we advise that qualified staff must execute any alterations of these parameters The parameters of the Setup Analysis are Interval Setting of the waiting time between each analysis Ex Setting up 2min it will execute an analysis every 5 minutes 3minutes of analysis 2 minutes waiting Initial Wash Setting of the cell Washing time at the beginning of the analysis expressed in seconds Default 60 seconds Injection DPD1 2 Setting of the peristaltic spin time of the reagents dosage 1 and 2 Default 1 0 second 2 reaction Setting
15. e hydraulic part must perfectly be inserts in the plant paying particular attention to the hydraulic lacing both in entrance than in exit This won t have any obstructions except those preview from the project The plant must be maintained operational in the full respect of the foreseen rules safety The parameters set on the command of the Controller of analyses must be conform to the current law The signals of damage of the controller must be put in a place constantly under control of the operator The missed respect of oneof these conditions can force the logic of the controller to operate potentially in dangerous way for the consumers of the service We recommend therefore to operators of service and or maintenance to operate with the maximum scrupulousness signalling at the right moment any removal of the safety parameters this to avoid conditions potentially dangerous Since the considerations don t reenter in the possibility of control from part of the product in object the builder is not considered responsible of the possible damages that such malfunctions can produce to people and or things T4322 TELEPOOL PROFESSIONAL Z ENGINEERING INFORMATION ON THE RECYCLING MATERIAL ENGINEERING CORPORATION srl in accord to the specific European directives 1s addressed to improvement the project and the production procedures of its own systems with the purpose to reduce at best the negative impact on the environment conce
16. g the measure the dosing and the calibration of Free Chlorine and Combine Chlorine optional 1 1 Thresholds SL Clorat ion 52 Cloration 54 Decloratriofn Alarm Timeout S1 CHLORINATION gt RELAIS 51 OFF gt RELAIS S1 ON Setup Parameter of the first threshold of Chlorination Hysteresis fixed at 0 1 The value of S1 must be inferior or equal to the threshold of S2 It cannot have a superior value to the threshold S2 Logic if the value of the chlorine goes down under 51 the Relay 51 will be closed until the value of the chlorine won t overcome the threshold of 1 S2 CHLORINATION gt RELAIS S2 OFF gt RELAIS S2 ON Setup Parameter of the second threshold of Chlorination Fixed hysteresis to 0 1ppm The value of S2 must be greater or equal to the threshold of S1 It cannot have inferior value to the S1 threshold Logic if the value of the chlorine is inferior to S2 the Relay S2 will be closed and remained closed until the value of the chlorine will not exceed the threshold of S2 S4 DE CHLORINATION gt REL 54 OFF gt RELE S4 ON Setup Parameter of the De chlorination threshold Fixed hysteresis to 0 1ppm The value of S4 must be greater or equal to the threshold of S2 It cannot have inferior value to the S2 threshold This SECURITY allows to avoid the contemporaneously dosage of Chlorination and De chlorination incompatible products Logic if the value of the chlorine is greater than the value of S4 the Relay
17. ifferent languages performed by distributors or same consumers The observance of the operational procedures and the instructions described 1n the manual present it 1s an essential requisite for the correct operation of the instrument and to guarantee the safety of the operator The manual must be reads in all of its parts in front of the instrument as phase necessary to the use so that results clear the formalities of operation the commands the connections to the peripheral equipments and the precautions for a correct and sure use The manual of use has to be preserved entire and legible in all of its parts in a sure place and at the same accessible time quickly from the operator during the operations of installation use and or revision of the installation 4 32 TELEPOOL PROFESSIONAL Z ENGINEERING CONVENTIONS The present user manual uses the following conventions NOTE The notes contain important information to put in evidence in comparison to the rest of the text They generally contains useful informations to the operator to perform in correct way and to optimize the operational procedures of the instrument ADVERTISING The advertising message appear in the manual before procedures or of operations that must be observe for avoiding the to verify him of possible losses of data or damages to the equipments ATTENTION The messages of attention appear in the manual in correspondence of the description of procedure
18. ify the cleaning of the reaction cell work for at least 15 minutes Weekly with the circuit off Then open the hydraulic circuit again Immerse the probes in F21 Misleading values Barchemical Verify the electrodes cleaning e rad ri deed Monthly cloth Pour 200ml of F21 Barchemicals into the probes Misleading values container and leave to work reading for at least 15 minutes with the circuit off Then open the hydraulic circuit again Check the reagents colouration Clean the Verify the cleaning of the reagents Misleading values connections and replace the Weekly connecting pipes 3 Teading Monthly Verify the probes port cleaning ORDINARY TELEPOOL PROFESSIONAL Z ENGINEERING Removal of Verify the lubrication of the peristaltic peristaltic pipes and s r A TA Monthly pump pipes misleading values reading Replace the reagents if the colouration is not transparent and clean the peristaltic pumps pipes and the reaction cell Verify the presence of the reagents and that the connection pipes are complete and functional at the Daily reagents transportation 1nto the reaction cell Eventually contact the assistance Verify the presence of water in the Misleading values Verify the presence of alarms I di Reset and eventually contact Daily reaction ce reading Problem Verify the connection between the detection Ad tel t the cabl electrode cable and the probe Problem pH
19. libration function of the Rx potential carried out on a single point with a solution of known voltage Sample Rx Offset Calibration Calibration with a solution of know voltage 475mV 3 0 Conductivity In this section you can find all the parameters concerning the conductivity measurement and calibration 3 1 Threshold Threshold uS THRESHOLD Setting Parameter of logical Conductivity threshold related to the lack of analysis water The threshold of the Conductivity is used to discover the lack of analysis water If the threshold is set up on 0 uS the Lack of Water function is deactivated If the conductivity value decrease below the threshold set up the instrument will switch on the alarm Lack of Water by activating the alarm Relay and will deactivate all the measurements and all the dosages When the water returns the instrument will automatically resume the normal operation 3 2 Calibration Sample 1 air Sample 2 Function of Conductivity calibration carried out on two points with salt Solutions of known conductivity Two points calibration Sample 1 air Offset calibration put the probe in the air and accurately dry it Sample 2 Gain calibration Calibration with Salt Solution of known conductivity The choice of the value of such solution will be decided based upon the value of the conductivity in which the probe will normally work 4 0 TEMPERATURE Temperature Offset setting 4 1 Offset 26 32 TELE
20. lows the instrument to control the correct operation of the dosing part controlled externally and also the reliability of the pH measure 1 5 Calibration 24 32 TELEPOOL PROFESSIONAL A ENGINEERING Calibration function of pH measure carried out on two points or a single point using buffer solutions of known pH Two points Calibration Sample 1 pH Offset calibration Calibration with buffer solution pH 7 Sample 2 pH Slope Calibration Calibration with buffer solution pH 4 or pH 9 The choice between 4 and 9 depends on the working pH One point Calibration Sample 1 pH Offset calibration Calibration with Solution of known pH The calibration to a point can be used in order to align the value of pH to a sample of the water to be analyzed 2 0 REDOX SECTION In this section you can find all the parameters concerning the Redox potential measurement and calibration 2 1 Threshold S5 Threshold 55 Threshold Setting parameter of the logical Rx threshold The 55 threshold of Rx potential is used to deactivate the Chlorine measurements If the Rx potential value is higher than the 55 threshold the instrument will automatically deactivate the measurement of Chlorine and on the display will appear Ll2 Subsequently if the Redox value decreases below the S5 threshold the instrument automatically resumes the measurements of the Chlorine 1 2 Calibration sample AZ IV TELEPOOL PROFESSIONAL Z ENGINEERING Ca
21. of the reaction time for the free chlorine measurement Default 30 seconds Step CI Comb Step of Combined Chlorine analysis Represents the number of Free Chlorine analysis that must be completed before carrying out a Combined Chlorine measurement If O is set up on the display the instrument won t carry out any measurement of Combined Chlorine Default 0 The measurement of Combined Chlorine is optional Injection DPD3 Setting of the peristaltic spin time of the reagent dosage 3 Default 0 5 second The measurement of Combined Chlorine is optional Reaction comb 23732 TELEPOOL PROFESSIONAL Z ENGINEERING Setting of the reaction time for the Combined Chlorine measurement Default 20 second The measurement of Combined Chlorine is optional 2 0 pH Section In this section you will find all the parameters for pH measurement dosage and calibration 1 4 Threshold Measured Product ACIDIC S3 Threshold 1200 Timeout alarm 0 min ON MEASURED PRODCT Setting of the type of product used for the pH correction The choice is between Basic or Acidic Setting up Acidic the threshold will work in ascending way if the pH value is higher than the S3 threshold the instrument will activate the S3 relay and it will remain active until the value decreases under the S3 threshold Setting up Basic the threshold will work in descending way if the pH value is below the S3 threshold the instrument will activate the S3 relay and i
22. rder to re enter in the normal operation EXECUTION OF THE BREAKPOINT Every time ENABLED is selected the execution of the phase of Breakpoint in compliance with the value of the parameters is enabled Entering in RUN MODE once the Start time is reached the blinking icon appears On display 2 it is possible to visualize the Breakpoint state see the following example BREAKPOINT 26702707 23230 PHASE 1 00 30 PHASE 2 00 60 PHASE 3 I a C12 Rxmax The example shows the Breakpoint starting time set up at 23 30 the duration of phases 1 2 3 are respectively 30 60 30 minutes At the bottom of the display it appears the value of the measured Cl2 and the highest value of the Redox Supposing that the finish time has been set up at 02 30 that means the Breakpoint must terminate in any case the 27 02 07 at 02 30 the maximum limit time in which the phase of Breakpoint could be started will be T START LIMITE T FINISH 120 min 00 30 on the 27 02 07 Supposing that the Telepool is momentarily OFF phase 1 hasn t begun yet and it is switched ON entering in RUN mode on the 27 02 07 at 00 10 since this time is inferior to T INIZIO LIMITE the Breakpoint starts immediately with the phase 1 21 32 TELEPOOL PROFESSIONAL Z ENGINEERING Phase 1 The Relay 51 and S2 are active The following outline represents display 2 during the 1st phase BREAKPOINT 217 02 07 00 10 PHASE 1
23. reading 0 detection Verify the reagents colouration ideal Misleading values colouration transparent reading Verify that the reagents get to the reaction cell through the manual activation of the peristaltic pumps Misleading values reading Rx reading 0 32192
24. ripheral conforming to the norms of his her own category of affiliation replace immediately damaged parts Cables connectors accessories or other parts of the instrument that resulted damaged or not working correctly must be immediately replaced Contact in such case the nearest center of technical support authorized use only accessories and peripheral specified by the firm ENGINEERING CORPORATION srl To guarantee all the safety requisite is necessary to exclusively use the accessories specified in this manual which are in combination with the instrument 6 32 TELEPOOL PROFESSIONAL Z ENGINEERING SAFETY OF THE OPERATIONAL ENVIRONMENT The panel of the controller and the containing box the electronic part and of connection of the hydraulic remote are protected against the entry of liquids Please avoid to use the instrument in environments where 1s present the risk of dripping spray or immersion Instuments in which liquids are accidentally penetrated must immediately be cleaned and checked from personal qualified authorized Use the instrument within the environmental limits of temperature damp and pressure specified The tool is built to operate in the followings environmental conditions temperature environment 5 C 45 C relative damp 5 95 RH Not Condensed ATTENTION The plant of watertreatment in which the system is inserted has to be realized in the respect of the functional requisite imposed by the current Law Th
25. rmers where the supply goes feeding other systems over the controller even inductive type because it can create spike of tension also of 1000 Volts that once radiated can be hardly eliminated The electric feeding line must be provided of opportune ground fault interrupter in the respect of the good norms of installation in every case it always well to verify the goodness of the ground connection The controller must be installed to the wall making attention that there is enough space for the passage of the wires and to look at the display of visualization data Lacing to the electric line Assuring that the feeding as to respects what already told on the previous paragraph connect the electric line using the supplied special cable 10 32 TELEPOOL PROFESSIONAL CGlalloVerde massa Marrone fase Connector for 220V ac Blu neutro 1 Comune 2 51 Cloro 3 S2 Cloro 4 S4 Declorazione 5 S3 pH 6 non connesso 7 Allarme Connector Exit Signals lato collegamenti 1 ABL Set Point connettore Maschio E Y 3 4 W gt Serial Connector 5 GND 6 ABL Set Point 7 non connesso lato collegamenti Connectors Position alimentazione 220 Vac 11732 TELEPOOL PROFESSIONAL ENGINEERING Water Lacings HYDRAULIC PART CHARACTERISTIC Water Lacing Rapid Connection for 8x10mm tubing Discharge For sample discharge Temperature of the water sample from 15 C to
26. rning the management of componets spare parts material of consumption packaging and instrument worklife Packaging are concepted and produced to permit the reemploy or the recovery included the recycling of the most greater part of the materials and to reduce at best the quantity of refusals or residual to carry off To guarantee a correct environmental impact the instrument has been projected with the maximum circuit miniaturization as possible with the least possible differentiation of the materials and component with a selection of substances that guarantee the maximum recyclablility and the maximum re use of the parts and a disposal without ecological risks The instrument 1s built to guarantee the easy separation or replace of the materials containing polluting substances in comparison to the others particularly during the operations of maintenance and substitution of the parts ATTENTION The recycling of the packaging of the materials of consumption and of the instrument at the end of the worklife must be effected in accord to the corrent laws of the country in which the instrument is used 8 32 TELEPOOL PROFESSIONAL Z ENGINEERING DECLARATION of CONFORMITY EC STATEMENT OF COMPLIANCE C Fabbricante Engineering Corporation srl Producer Indirizzo Via Allende 14 41051 Castelnuovo Rangone MO ITALY address Declairs that the equipment Hereby states that the device known as MODELLO Telepool
27. rument it 1s necessary to operate in the admitted limits and to adopt all the precautions following you list ATTENTION Verify before the use that all the safety requisite are satisfied The instrument must not have fed or connected to other instruments up to when safety conditions are not satisfied ELECTRIC SAFETY ATTENTION All the present connections on the controller are isolated from the earth environment non isolated mass Don t connect none of these connections to the mass With the purpose to guarantee conditions of maximum safety for the operator it recommends him to follow all the indications listed 1n the manual present Supply the instrument exclusively through its own adapter replace immediately the damaged parts Cables connectors accessories or other parts of the instrument that resulted damaged or not working correctly must be immediately replaced Contact in such case the nearest center of technical support authorized use only accessories and peripheral specified by the firm ENGINEERING CORPORATION srl To guarantee all the safety requisite is necessary to use exclusively accessories specified in this manual which has been made a will in combination with the instrument The use of accessories and materials of consumption of other producers or not specifically pointed out by the firm ENGINEERING CORPORATION srl it doesn t guarantee safety and the correct operation of the instrument Use exclusively pe
28. s indicate that the cell is getting dirty With values below 250 the instrument activate the alarm dirty cell pH Value expressed in mV and read by the pH probe REDOX Value expressed in mV and read by the Rx probe CONDUCTIVITY DIGIT value read by the conductivity probe TEMPERATURE Value of temperature read by the NTC probe without offset correction DOSAGES Digital entering state of the dosage ON indicates that the dosages are active OFF indicates that the dosages are enactive COM OK 30 32 TELEPOOL PROFESSIONAL Z ENGINEERING Indicates if the connection of the hydraulic card 5 8Information Val K Cl 4 25 pH Gain 57 14 mV pH Offset 0 10 mV Rx Offset mV Val k Cl K factor value used for the chlorine measurement The default K factor is 4 25 pH Gain Value expressed in mV of the pH probe Ideal value 57mV pH Offset Value expressed in mV of the pH probe offset Ideal value 0mV Rx Offset Value expressed in mV of the Rx probe offset Ideal value OmV 6 EXIT before exiting the menu the instrument will ask confirmation if save or not the data set up Clicking on amp the data will be saved and you re enter the RUN mode Clicking on the data won t be saved and the instrument remains in SETUP TELEPOOL MAINTENANCE HANDBOOK POSSIBLE SINTOMS GENERATED CORRECTIVE ACTION id PROBLEM Pour into the cell a little amount of F21 Barchemicals using the lid and leave to Ver
29. s or operations that if you perform in non correct way could cause damages to the operator DECLARATION OF RESPONSIBILITY OF THE MANUFACTURER ENGINEERING CORPORATION srl is considered responsible to the effects of the safety reliability and performances of the instrument only if used in the respect of the followings conditions Settings changes or reparations must be effected from personal qualified and expressly authorized by the firm ENGINEERING CORPORATION srl The opening of the instrument and the access to its inside parts must only be effected from personal qualified for the maintenance and on purpose authorized by the firm ENGINEERING CORPORATION srl The environment in which the instrument is used has to be conforming to the safety prescriptions The electric plant of the environment must be realizes according to the norms and perfectly efficient The practicable substitutions of parts of the instrument and accessories must have effected with others of the same type and having the same characteristics The use and the maintenance of the instrument and the relative accessories must be effected in conformity to the instructions described in the manual present The manual present must have maintained entire and legible in all of its parts 5 32 TELEPOOL PROFESSIONAL Z ENGINEERING LIMITS OF USE AND PRECAUTIONS FOR THE SAFETY With the purpose to guarantee the safety of the operator to a correct operation of the inst
30. surement if the chlorine value decrease under the S4 threshold the Breakpoint phase will terminate and on the screen will appear the icon On the contrary if the reliability of the measurements won t be ensured and or the chlorine value will not decrease under the S4 threshold within the De chlorination set time the Breakpoint will stop The icon will appear on the screen and the instrument will wait the operator s confirmation before terminate the Breakpoint phase and restart the chlorine analysis Anyway the instrument will terminate the Breakpoint phase when reached the Finish time or if it doesn t receive the operator s confirmation Then will start the chlorine analysis again STATE Flashing Breakpoint Phase active Software step used to activate or deactivate the Breakpoint Phase In order to modify the Breakpoint Parameters the status must be on Deactivated Attention Activate the Breakpoint function only when anybody is in the pool Setting ENABLED the Breakpoint phase will be activate as soon as you return to RUN MODE and the Start time is reached If the Breakpoint phase is active and you set DISABLED it will be permanently cancelled 20 32 TELEPOOL PROFESSIONAL Z ENGINEERING When the machine enters the RUN MODE switching on the instrument or exiting the setup will start the Breakpoint phase if the Start time has been passed but not the Finishing time calculated as follow T START THRESH
31. t will remain active until the value overcomes the S3 threshold S3 THRESHOLD gt RELE S2 OFF gt RELE S2 ON Parameter of pH threshold setting Hysteresis fixed at 0 05pH Example setting up the parameters as in the above display the dosage will be carried out as follows when the pH value exceeds 7 00pH the dosage is activated and remains active until the value decrease under 6 90pH If as Measured Product has been set up Acid it will work as follows if the pH value is higher than the S3 threshold the instrument will activate the relay of S3 and it will remain active until the value decreases under the S3 threshold 0 1pH If as Measured Product has been set up Basic it will work as follows if the pH value of is smaller than the S3 threshold the instrument will activate the relay of S3 and it will remain active until the value exceeds the threshold S3 0 1pH TIMEOUT ALARM Security parameter concerning the dosage of the pH Section If it is set up on 0 minute the function is deactivated If the pH threshold S3 remains active for a period of time higher than the one set up the instrument will stop all the dosages and will activate the alarm relay On the screen will appear the icon This alarm re enters automatically when the pH value will deactivate the threshold in Timeout Once the alarm is re entered the dosages will resume to their normal operation and the alarm relay will become deactivated This security parameter al
32. tion The timing for the three phases are set as following Software 2 2 from a minimum of 30 minutes to a maximum of 120 minutes 2h at 15 minutes steps Software 2 3 from a minimum of 5 minutes to a maximum of 120 minutes 2h at 5 minutes steps The Start and Finish time are the hours when the Breakpoint must start ant finish and can be set from 00 00 to 23 59 at 1 minute steps The end of the Breakpoint depends on the duration of the Chlorination Waiting and De chlorination Usually stops before the Finish time Therefore the Finish time set indicates a maximum limit after which the Breakpoint stops Phase of Chlorination the instrument will activate the Relays S1 and S2 for the duration of the set time When the chlorination starts the machine will memorize the finishing time This security system allows precisely stopping the chlorination phase at the set time even in case of prolonged blackouts Phase of Waiting the instrument will deactivate the 51 and S2 Relays for the set time and won t do any analysis This phase allows to the dosed chlorine to react in the water Phase of De chlorination the instrument will activate the S4 Relay When the Redox potential value decreases under the threshold the machine will activate the chlorine measurement From this moment all the results will be filtrated through an algorithm that will determine the reliability and trend Once ensured the reliability of the chlorine mea
33. to enter the contrast function notified with 3 beep Erase the made change kept pushed for more than 3 seconds you enter the Setup Increase Value Modify Setup Decrease Value Modify Setup At the switch on kept pushed at the same time you enter the function of UP grade SW notify by 1 beep Forced switch on of peristaltic pump Free Chlorine Forced switch on of peristaltic pump Combine Chlorine optional Keeping pushed for more than 3 seconds the ESC button you can enter the instrument setup putting the first 4 letters password With the arrows you can slide the voices of the menu With the button 10 you can select the highlighted voice after with the arrows you can change the value or the set point Pushing again OK you can confirm the desired setup otherwise pushing ESC you cancel the modify 17 32 TELEPOOL PROFESSIONAL AL ENGINEERING MAIN MENU 1 0 CHLORINE SECTION THRESHOLDS BREAKPOINT CALIBRATION ANALYSYS SETUP 2 0 pH SECTION THRESHOLDS CALIBRATION 3 0 ORP SECTION THRESHOLD CALIBRATION 4 0 CONDUCTIVITY THRESHOLD CALIBRATION 5 0 TEMPERATURE OFFSET 6 0 SHOW DATA SHOW INTERVAL DATA 7 0 COMMON DATA SYSTEM DATA ALARM ARCHIVE PASSWORD MODIFY 18 32 TELEPOOL PROFESSIONAL Z ENGINEERING 8 0 SERVICE 8 1 RELAIS 8 2 ENTRY 8 3 INFO 9 0 EXIT DESCRIPTION MENU 1 0 CHLORINE SECTION In this Menu you can set all the parameters concernin
34. visualisation mode of the display It can be Normal or Reversed Contrast Setting up of the display contrast between 1 and 100 5 3 Alarm The relay alarm is cumulative of all the errors It will be possible to visualize the single errors by entering the RUN display with the last 13 alarms activated Logic CLOSED Setting up of the working logic for the alarm relay Setting up Closed if the instrument is in alarm the alarm relay will be activated instead if It is in normal operation it will be deactivated Setting up Opened if the instrument is in alarm the alarm relay will be deactivated if it is in normal operation will be activated Important Setting up Opened there will be the security to activate an alarm in case the instrument brakes down or switches off 5 4 Archive In this menu are set up all the parameters concerning the data storage Considering that the archive can contain a maximum of 15000 recording increasing the recording step will increase the number of data stored step 3 mn lype 28 32 TELEPOOL PROFESSIONAL Z ENGINEERING Used 05 Heset gt gt gt gt STEP Period of time between each recording During each recording the instrument memorizes Date Hour and value of free chlorine combined chlorine pH redox conductivity and temperature TYPE Memorisation mode By setting this option it will use a circular storage When the archive is full the instrument will record on the oldest data
Download Pdf Manuals
Related Search