ELEX eco
Contents
1. under a ventilating fan etc 4 2 Wall Mounting Bracket The wall mounting bracket is oriented centrally See RHS diagram ae s a Step Loosen the locking plate screw and rotate the locking plate out of the fixing slot See RHS images Then remove the mounting bracket from the heater Step 2 Use the wall mounting bracket as a template for marking the fixing holes Position the mounting bracket in the correct position on the wall and mark the screw holes through the 4 mounting holes See RHS diagram y gt Z m m L m gt m 2 7 Step 3 Install the 4 fixing devices in the wall ensuring they are more than adequate to safely fix the heater to the wall ST4 expansion screws are suggested g eco THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 THERMOFILM Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au FLEX CQ Step 4 Fix the bracket firmly to the wall using all 4 mounting locations Step 5 Mount the heater on the bracket so the bracket protrusions fix into the 4 slots on the back of the heater See RHS diagram Rotate the locking plate into the fixing slot and tighten the screw To remove the heater reverse the above operation 4 3 Castor Wheel Set Part list Se B Castors 4PCS Clip 2PCS T a Support 2PCS 4 4 Electrical connection This heater is suitable for 230 240V Please observe national standards the regulations2. www thermofilm com au FAILLIOAAN ODO y gt Z m m L m gt m 2 V FLEX CQ 4 1 Installation Location The ELEX CO convective panel heater was designed to be installed in a residence Please ask your distributor before using it for any other purpose The ELEX ECO convective panel heater should be installed according to normal trade practice and in compliance with legislation in relevant country Volume 2 Volume 1 60 The panel convector is CLASS I and is protected volume 2 against splashed water IP24 Therefore it can be installed outside the shaded area shown in the bathroom area Ensure the safety zones mm in diagram left hand side are kept free FAILLIOAAN ODO If the wall covering is laid on foam a spacer the same thickness as the foam must be placed under the panel heater s support This ensures there is free space behind the panel heater to make sure its control settings are not adversely affected The ELEX CO convective panel heater must not be installed immediately below a wall socket The heater must be connected to a socket outlet or permanent terminal box at least 0cm to one side of the heater If the heater is installed in the Bathroom or in humid area the socket outlet or permanent terminal box must conform to the IP24 requirement The ELEX ECO convective panel heater must not be installed in a draught likely to affect the control settings
3. FLEX CQ ELEX CCO CONVECTIVE PANEL HEATER USER MANUAL Models ELEX CO 2400 ELEX CO 2000 ELEX CO 1500 ELEX CO 1000 TABLE OF CONTENTS Important Safety Instructions 2 Specification Data 3 Operating Instructions 3 1 Control Panel Guide 3 2 Switching on the Unit 3 3 Preset Temperature 3 4 Setting the 30min 60min 90min Timer 3 4 1 Setting the 30min Push Button Timer Programme 3 4 2 Setting the 60min Push Button Timer Programme 3 4 3 Setting the 90min Push Button Timer Programme 3 4 4 Changing to another Timer Setting in Mid Programme 3 5 Locking the Control Panel 3 6 Unlocking the Control Panel 3 7 Safety Notes 3 8 Maintenance 4 Installation Instructions 4 Installation Location 4 2 Wall Mounting Bracket 4 3 Castor Wheel Set 4 4 Electrical Connection 4 5 Safety Notes 5 Warranty THERMOFILM THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 eco P Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au FAILLIOAAN ODO y gt Z m m L m gt m 2 7 FLEX CQ Important Safety Instructions Prior to installing and operating the heater read these instructions carefully and retain for future reference Indoor use only Ensure the rated voltage is 230 240V Do not install the heater directly below a socket Always operate heater in an upright position with the control panel at the top If using castor wheel set heater should be positioned on a flat h
4. OAAN ODO y gt Z m m L m gt m 2 7 FLEX CQ 2 Specification Data ELEXECO 1000 ELEX CO1S00 ELEX CO 2000 ELEX ECO 2400 Power VW LOOOWsC F IS00W ss 2000VW 2400W Voltage V sas a 240V 50Hz 240V 50Hz 420 x 440 x 105 580 x 440 x 105 740 x 440x 105 1000 x 440 x 105 3 Operating Instructions The control panel features a 30min 60min 90min push button timer with digital countdown timer display This heater is designed to heat at an economical preset temperature of 21 C for the chosen time of 30min 60min or 90min 7 6 5 4 3 2 1 FAILLIOAAN ODO THERMOFILM EEEX eco 3 1 Control Panel Guide I Main Power Switch 1 0 ON OFF 2 Unit Power button ON OFF 3 30 minute push button timer 4 60 minute push button timer 5 90 minute push button timer 6 LED screen 7 Power On light 3 2 Switching on the Unit Press the main power switch 1 on the right hand side of panel Press the button i on the control panel This turns the unit ON and the LCD screen 6 will illuminate displaying y gt Z m m L m gt m 2 7 Note The red ON indicator light 7 illuminates when the heating element is operating Upon first use the heater may give off some fumes this is normal Ensure that the room is ventilated for example open a window 3 3 Preset Temperature The preset temperature setting for the ELEX ECO heater is 21 C and this cannot be altered
5. THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 eco P Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au THERMOFILM FLEX CQ 3 4 Setting the 30min 60min 90min Push Button Timer Note The 30min 60min or 90 min programme may be terminated at any time by pressing the button and the heater will turn off To modify a selected programme see 3 4 4 Changing to another Timer Setting in Mid Programme To ensure a selected programme is not modified see 3 5 Locking the Control Panel 3 4 1 Setting the 30min Push Button Timer Programme oe Press the J button the display will be 30 The red ON indicator light illuminates the heater starts working and produces heat at the 21 C preset temperature for 30 minutes The digital display will countdown the time remaining from 30 minutes to 00 minutes Once the digital display reaches the heater will turn off 3 4 2 Setting the 60min Push Button Timer Programme 60 Press the button the display will be S0 The red ON indicator light illuminates the heater starts working and produces heat at the 21 C preset temperature for 60 minutes The digital display will countdown the time remaining from 60 minutes to 00 minutes Once the digital display reaches the heater will turn off 3 4 3 Setting the 90min Push Button Timer Programme 30 66 99 o Press the button the display will be So The red ON in
6. ching the plug and mains supply connections Never leave the appliance unattended when connected to the mains power supply Do not cover NEVER use the heater to dry clothes or similar articles Do not position the appliances close to curtains or other combustible materials Keep combustible material such as furniture cushions bedding paper clothes curtains etc at least 0m away from the heater The most common cause of overheating is deposits of dust or fluff in the appliance Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning air vents and grilles This appliance heats up when in use To avoid burns do not let bare skin touch hot surface Switch off and let cool down before moving Store the heater in a cool dry location when not in use Do not use this appliance with a programmer timer or any other devices that switches the appliances on automatically Do not use an extension cable with this appliance Do not use the appliance in rooms less than 4m area This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety THERMOFILM THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 eco P Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au FAILLI
7. dicator light illuminates the heater starts working and produces heat at the 21 C preset temperature for 90 minutes The digital display will countdown the time remaining from 90 minutes to 00 minutes Once the digital display reaches the heater will turn off 3 4 4 Changing to another Timer Setting in Mid Programme The ELEX CO heater can reset and begin another timer setting at any point during the countdown time of a selected 30min 60min or 90min programme For example You have previously selected the 30 minute programme the digital display shows Del and you have 30 2 minutes remaining Press the button the display will reset to 30 The heater will continue working for 30 minutes The digital display will countdown the time remaining from 30 minutes to 00 minutes Once the digital display reaches GOI the heater will turn off 3 5 Locking the Control Panel To ensure that the selected 30min 60min or 90min programme is not reset to another programme you can lock the control panel after a programme has been selected To lock the control panel press the 30 button and the 50 button simultaneously for around three 3 seconds The heater will beep 3 times indicating the control panel is locked The selected programme will countdown until the digital display reaches and the heater will turn off THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 eco P Ph 03 9562 3455 Fx 03 9548 3979 www thermof
8. ilm com au THERMOFILM FAILLIOAAN ODO y gt Z m m L m gt m 2 7 FLEX CQ Note No other buttons including the button will function when the control panel is locked If any button is pressed the digital display will flash 3 times and the heater will beep three times to indicate the control panel is locked 3 6 Unlocking the Control Panel To unlock the control panel press the 30 button and the 50 button simultaneously for around three 3 seconds The heater will beep 3 times indicating the control panel is unlocked 3 7 Safety Notes The air outlet must not be obstructed For safety reasons the upper and lower air grilles must never be covered with items such as washing nor obstructed by items in close proximity see figure to right Objects should not be leant ps against the unit nor placed between the unit and the wall FE Never leave combustible materials such as wood paper textiles or Taable items such as wax petrol aerosol cans etc in the vicinity of the warm air outlet As with all similar heaters the flow of rising air may cause discoloration of the wall The appliance must not be operated e n areas which are subject to the risk of fire or explosion due to chemicals dust gases or vapors e In the immediate vicinity of pipes or containers which carry or contain combustible or potentially explosive substances For this reason the minimum clearance intervals must not be undercut I
9. n workshops or other areas in which the odor of waste gases oil petrol etc might occur or in which work is carried out involving solvents and chemicals there is a risk of sustained odor burdens being engendered and possibly of dirt contamination occurring Before using any materials which produce flammable gases or vapors e g laying or sealing parquet or PVC flooring or when using spray polishes spirits and similar materials ensure the heater is switched off 3 8 Maintenance Do not use abrasive or aggressive cleansers to clean the heater Use a vacuum cleaner regularly to clean the upper and lower air grids 4 Installation instructions The ELEX ECO convective panel heaters are electric heaters designed to be mounted on the wall or freestanding using the supplied castor wheel set These units are suitable for heating enclosed indoor rooms such as bedrooms studies offices living areas and bathrooms ATTENTION The installation electrical connection and first operation of this appliance should be carried out by a qualified installer The company does not accept liability for failure of any goods supplied which have not been installed and operated in accordance with the manufacturer s instructions These installation instructions belong with the heater and must be handed on to the purchaser if the heater is sold THERMOFILM THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 eco Pe Ph 03 9562 3455 Fx 03 9548 3979
10. of your local electricity supply company as well as data on the rating label Electrical safety The ELEX CO convective panel heaters are IP24 protected against splashing water In humid areas such as bathrooms the power socket must be installed at least 25cm above floor level Note the details on the rating plate The voltage supply must match the requirements on the rating plate The supply cable must be correctly sized The heater must be connected to a socket outlet or permanent terminal box at least 10 cm to one side of the heater Please note in general Where the ELEX CO convective panel heater is fitted in a room with a bath or shower ensure the safety zone defined in IEE Regulations is applied in accordance with the details on the rating plate To avoid hazards if the power cord of the appliance exhibits visible damage it must be replaced by the manufacturer or his service agent or a qualified electrician 4 5 Safety Notes The ELEX CO convective panel heater is equipped with a safety cut out that switches the heater off if it overheats g eco THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au THERMOFILM FAILLIOAAN ODO y gt Z m m adi m gt m 2 r FLEX CQ Once the heater has switched off due to overheating remove the cause of the fault e g blocked air grids When the heater has cooled down for several minutes it will
11. orizontal surface Arrange cord away from traffic areas so that it will not be tripped over Do not place the cable under carpets rugs Do not remove plug from power socket by pulling the supply cord Always grip plug Do not operate this appliance if the cable or plug becomes damaged In case of heater fault or damaged supply lead the appliance should be returned to the distributor manufacturer for repair Ensure the appliance is switched OFF before connecting to the mains power supply Do not cover or restrict airflow to the inlet or outlet grills in any manner as the appliance may overheat and become a fire risk Do not insert or allow foreign objects or metal utensils to enter any grill opening as this may cause an electric shock or fire damage to the appliance Do not operate in areas where gasoline paint or other flammable liquids are used or stored Switch off the power supply and unplug from the mains socket when not in use before cleaning or changing accessories To prevent overload and blown fuses do not plug other appliances into the same power outlet receptacle Do not immerse in liquid or allow liquid into the interior of the appliance as this could create an electric shock hazard Do not reach for an appliance that has fallen into water Switch off at supply and unplug immediately Do not operate appliance with wet hands Always ensure that hands are dry before operating or adjusting any switch on the product or tou
12. restart automatically If the heater then cuts off again switch off the heater and call an authorized serviceman 5 Warranty ELEX CO heaters have a SEVEN 7 YEAR FULL REPLACEMENT WARRANTY To claim for Warranty please retain your receipt as proof of purchase and return the faulty heater to the place you purchased it Warranty does not apply to heaters which have been misused or used in conditions other than those for which they were intended for Nor will it apply in the event of damage or accident resulting from negligence lack of care or maintenance or if the heater has been modified in any way Thermofilm Australia Pty Ltd reserve the right to reject any Warranty claim deemed to be false Retailers must have Warranty claims authorised by Thermofilm Australia Ph 03 9562 3455 Conditions apply Please refer the Thermofilm standard terms of sale and warranty for details THERMOFILM AUSTRALIA 27 Rosalie Street Springvale VIC 3171 eco P Ph 03 9562 3455 Fx 03 9548 3979 www thermofilm com au THERMOFILM FAILLIOAAN ODO y gt Z m m L m gt m 2 7
Download Pdf Manuals
Related Search