Varia™ Bike Lights
Contents
1.2. Auto Automatically adjusts the light intensity based on the ambient light or time of day Day Sets the light intensity for day Night Sets the light intensity for night Power Save Automatically adjusts the light intensity based on the remaining battery life of the bike light When battery life is low the light intensity is reduced to prolong battery life Individual Allows you to customize the light intensity and pattern mode for each light in your network Light Network Settings page 4 Adjusting the Beam Angle During a Ride Before you can adjust the beam angle during a ride you must disable the automatic beam angle setting Customizing Varia Device Settings with Your Edge 1000 page 3 1 Go for a ride 2 Swipe the screen to view the bike lights data screen 3 Select f or to adjust the headlight beam angle Turn Signal Settings From your Edge device select X gt Sensors gt Varia gt Turn Signal Setup Enable Allows the paired Edge device to assign and control turn signals Auto Cancel Automatically cancels the turn signal after making a 90 turn NOTE Your paired Edge device must have GPS turned on in order to use the Auto Cancel setting Right Assigns the right turn signal Left Assigns the left turn signal Assigning Turn Signals When using two taillights you must indicate which light is the left turn signal and which light is the right turn signal 1 Pair two taillights with your Edge dev
3. taillight intensity and pattern when decelerating sharply NOTE This setting appears when a taillight is paired with the device NOTE Taillight medium and flash modes are available on the Varia TL 300 device only Light Mode Sets the light intensity and pattern mode or turns off the light NOTE This setting is available when the Individual configuration setting is selected Configuration Settings page 3 About Displays device software and battery information Remove Allows you to delete a paired light from the network Checking the Battery Level From your Edge device select X gt Sensors gt Varia gt Light Network The battery level for all paired lights appears Testing the Light Network 1 From your Edge device select X gt Sensors gt Varia gt Test Lights 2 Select a light to test The light blinks when it is connected Wireless Remote Control Device Overview Taillight key Select to signal a left turn when using two taillights Hold to cycle through the taillight intensity and pattern modes Headlight key Select to switch between low beam and high beam Hold to cycle through the headlight intensity and pattern modes 3 Taillight key and power key Select to signal a right turn when using two taillights Hold to turn all lights on and off Status LED Status LED LED Activity Status Flashing green Searching for a paired device At
4. the notches with the sides of the mount and press the remote into the mount until it clicks e Press gently on the release tab and lift the remote from the mount Replacing the Battery Do not use a sharp object to remove batteries Keep the battery away from children Wireless Remote Control Never put batteries in mouth If swallowed contact your physician or local poison control center Replaceable coin cell batteries may contain perchlorate material Special handling may apply See www dtsc ca gov hazardouswaste perchlorate Contact your local waste disposal department to properly recycle the batteries Before you can replace the battery you must have a small Phillips screwdriver a small flat screwdriver and a CR2032 lithium coin cell battery 1 Using a Phillips screwdriver remove the three screws from the back plate oe 2 Remove the back plate from the remote 3 Wrap the end of a small flat screwdriver with tape The tape protects the battery battery compartment and contacts from damage 4 Carefully pry the battery from the back plate 5 Install the new battery into the back plate with the positive side facing down 6 Verify the gasket is fully seated in the groove 4 7 Replace the backplate aligning the post with the gap in the circuit board 8 Replace and tighten the three screws NOTE Do not overtighten Device Information Specifications He
5. A GARMIN Varia Bike Lights Owner s Manual August 2015 Printed in Taiwan 190 01906 00_0A All rights reserved Under the copyright laws this manual may not be copied in whole or in part without the written consent of Garmin Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements Go to www garmin com for current updates and supplemental information concerning the use of this product Garmin the Garmin logo ANT and Edge are trademarks of Garmin Ltd or its subsidiaries registered in the USA and other countries Garmin Connect Garmin Express and Varia are trademarks of Garmin Ltd or its subsidiaries These trademarks may not be used without the express permission of Garmin This product is ANT certified Visit www thisisant com directory for a list of compatible products and apps M N A02666 A02669 Table of Contents FON near ON E ai gt POEA EE EEN ER A E S T AA Sa uaea E E E A E Installing the Out Front Mount ccccccsssseeccesseeeseeeeeeeseeees Installing the Seat Post MOUNL ccccccsssececeeeeeeeseeeeeesseeees Installing the Multi Location Mount ccscceesseeeeeeeeeeeeeeeees Varia HL Device OVErVIOW cccccsccccsceeeececeeeeeeccesseeecseseeeeseaees Varia TL Device Over vig ictesiteesteciscevebestitiewtiesels ica see
6. America or the export control laws of any other applicable country Troubleshooting Index A accessories 6 B bands 6 battery charging 1 life 4 replacing 4 C cleaning the device 6 customizing the device 3 D device care 6 E Edge 3 4 G Garmin Express registering the device 6 updating software 6 installing 1 2 K keys 2 4 M maps updating 6 mounting the device 1 2 4 O O rings See bands P pairing 3 remote control 4 product registration 6 R registering the device 6 remote control 3 4 pairing 4 replacing the battery 4 resetting device 6 S settings 3 4 software updating 6 software license agreement 6 specifications 5 T troubleshooting 6 U updates software 6 USB 6 W wireless devices 4 Index www garmin com support 43 0 820 220230 0800 770 4960 ly 1 866 429 9296 PPM 385 1 5508 272 385 1 5508 271 32 2 672 52 54 420 221 985466 420 221 985465 45 4810 5050 358 9 6937 9758 331 55 69 33 99 39 02 36 699699 52 001 855 792 7671 0800 0233937 gt 44 2380 002915 35 1214 447 460 386 4 27 92 500 Ki 34 93 275 44 97 0861 GARMIN 427 646 Pa 27 0 11 251 9999 0808 238 0000 44 0 870 8501242 913 397 8200 1 800 800 1020 al 886 2 2642 9199 ext 2 49 0 89 858364880 zum Ortstarif Mobilfunk kann abweichen ENFIN TEs CE amp AM 2015 Garmin Ltd or its subsidiaries
7. Press down slightly and turn the device clockwise until it locks into place Varia HL Device Overview Device key Select to cycle through the headlight pairing intensity and pattern modes Hold to turn the device on and off Status LED View device status Bike Light Status LEDs page 2 Varia TL Device Overview Device key Select to cycle through the taillight pairing intensity and pattern modes Hold to turn the device on and off Status LED visible View device status Bike Light Status LEDs above the device key page 2 Bike Light Status LEDs LED Activity Solid red Status An error occurred while charging The device shut down to prevent overheating Alternating blue and green The device is uploading settings from Garmin Express Alternating blue and red An error occurred while uploading settings from Garmin Express Flashing green The battery is charging Solid green Charging is complete Flashing red The battery is low Flashing blue The device is in smart mode and can be controlled by a paired wireless remote oe the Device Key Hold the device key for 1 second to turn on the device The first time you turn on the device it enters smart mode The status LED flashes blue The device can be controlled by a paired wireless remote or Edge device Select the device key to cycle thr
8. act your Garmin dealer for information about optional accessories and replacement parts Appendix Software License Agreement BY USING THE DEVICE YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE AGREEMENT PLEASE READ THIS AGREEMENT CAREFULLY Garmin Ltd and its subsidiaries Garmin grant you a limited license to use the software embedded in this device the Software in binary executable form in the normal operation of the product Title ownership rights and intellectual property rights in and to the Software remain in Garmin and or its third party providers You acknowledge that the Software is the property of Garmin and or its third party providers and is protected under the United States of America copyright laws and international copyright treaties You further acknowledge that the structure organization and code of the Software for which source code is not provided are valuable trade secrets of Garmin and or its third party providers and that the Software in source code form remains a valuable trade secret of Garmin and or its third party providers You agree not to decompile disassemble modify reverse assemble reverse engineer or reduce to human readable form the Software or any part thereof or create any derivative works based on the Software You agree not to export or re export the Software to any country in violation of the export control laws of the United States of
9. ad around the seat post if necessary e Ifthe seat post diameter is 27 to 28 6 mm use the thicker pad e Ifthe seat post diameter is 30 4 to 31 mm use the thinner pad e Ifthe seat post diameter is 31 to 31 8 mm do not use a rubber pad Place the seat post connector around the rubber pad NOTE You should align the contours on the rubber pad with the grooves on the inside of the seat post connector Replace and tighten the screw NOTE Garmin recommends a torque specification of 7 Ibf in 0 8 N m You should check the tightness of the screw periodically Align the tabs on the back of the device with the seat post mount notches 7 Press down slightly and turn the device clockwise until it locks into place Installing the Multi Location Mount 1 Select a secure location to mount the taillight where it does not interfere with the safe operation of your bike NOTE You can mount the device on your seat post helmet backpack or other location Garmin recommends that you enable the deceleration indicator only when mounting the device vertically on your seat post If necessary select the correct rubber pad for your seat post shape Place the mount on the seat post or other mounting location Attach the mount securely using one or two bands NOTE You can use the hooks on the center of the mount if using only one band Align the tabs on the back of the device with the mount notches
10. adlight Specifications Battery type Rechargeable built in lithium ion battery Up to 2 5 hr in high mode Up to 5 hr in flash mode Flash mode is available on the Varia HL 500 only Battery life Operating temperature range From 15 to 50 C from 5 to 122 F Charging temperature range From 0 to 40 C from 32 to 104 F Radio frequency protocol 2 4 GHz ANT wireless communications protocol Water rating IEC 60529 IPX7 Varia HL 500 LED luminous 600 Im flux and peak illuminance 95 Ix Varia HL 501 LED luminous 300 Im flux and peak illuminance 65 Ix The device withstands incidental exposure to water of up to 1m for up to 30 min For more information go to www garmin com waterrating Headlight Light Intensity Modes Intensity Mode Varia HL 500 Illuminance Varia HL 501 and Luminous Flux Illuminance and Luminous Flux Overdrive 600 Im Not applicable 95 Ix High 400 Im 300 Im 70 Ix 65 x Medium 250 Im 200 Im 50 Ix 50 Ix Low 150 Im 150 Im 30 Ix 35 Ix Flashing 600 Im Not applicable 95 Ix Taillight Specifications Battery type Rechargeable built in lithium ion battery Battery life Up to 4 hr in high mode Up to 14 hr in flash mode Flash mode is available on the Varia TL 300 only Operating temperature range From 15 to 50 C from 5 to 122 F Charging temperature range Radio frequency p
11. ampened with a mild detergent solution 2 Wipe it dry Troubleshooting Resetting the Device You can reset the device if it stops responding Hold the device key for 8 seconds Thermal Safety Shutdown To prevent overheating the Varia device may turn off when operated at a high intensity in warm stagnant air The status LED is red until the device cools down You should use the device outdoors Replacement O rings Replacement bands O rings are available for the standard mount in two sizes e 1 3 x 1 5 x 0 9 in AS568 125 e 1 7 x 1 9 x 0 9 in AS568 131 NOTE Use Ethylene Propylene Diene Monomer EPDM replacement bands only Go to http buy garmin com or contact your Garmin dealer Support and Updates Garmin Express www garmin com express provides easy access to these services for Garmin devices e Product registration e Product manuals e Software updates Updating the Software Before you can update your device software you must have a Garmin Connect account and you must download the Garmin Express application 1 Connect the device to your computer using the USB cable When new software is available Garmin Express sends it to your device 2 Follow the on screen instructions 3 Do not disconnect your device from the computer during the update process Getting More Information e Go to www garmin com intosports e Go to www garmin com learningcenter e Go to http buy garmin com or cont
12. device you must pair the devices Pairing Varia Bike Lights with Your Edge 1000 page 3 e To turn on all paired lights turn on your Edge device e To turn off all paired lights turn off your Edge device Customizing Varia Device Settings with Your Edge 1000 Before you can customize Varia device settings with your Edge device you must pair the devices Pairing Varia Bike Lights with Your Edge 1000 page 3 1 From your Edge device select X gt Sensors gt Varia 2 Select an option e Select Enable to enable the light network e Select Configuration to set the light intensity mode for all lights in your network Configuration Settings page 3 e Select Beam Angle to automatically adjust the headlight beam angle based on the rate of speed Higher beam angles are used at high speeds and lower beam angles are used at low speeds NOTE This setting appears when a headlight is paired with the device e Select Turn Signal Setup to configure turn signals when using two taillights Turn Signal Settings page 3 NOTE This setting appears when two taillights are paired with the device e Select Light Network to view device information and customize each light in your network Light Network Settings page 4 e Select Test Lights to check that each light in your network is set up correctly Testing the Light Network page 4 Configuration Settings From your Edge device select X gt Sensors gt Varia gt Configuration
13. e iieiaei ee eens LUBOBBNE Me Sy OTN Ca erinnern Getting More Information ccccccccseeeecceeeeeesseeseeecseseesseaees a 021 1 2 E Software License AGreeMent ccccsscccccssseeeccesseeeceeeesecssaeeess Table of Contents Introduction See the mportant Safety and Product Information guide in the product box for product warnings and other important information Always consult your physician before you begin or modify any exercise program Getting Started You can use the Varia HL headlight and Varia TL taillight alone with the optional wireless remote or with your compatible Edge device This list provides an overview of the installation and setup tasks e Charge the device Charging the Device page 1 e Install the headlight using the out front mount Installing the Out Front Mount page 1 e Install the taillight using one of the included mounts Install the seat post mount Installing the Seat Post Mount page 1 Install the multi location mount Installing the Multi Location Mount page 2 TIP If you are using two taillights as turn signals you can install two multi location mounts on the seat stays of your bike e If you are using the wireless remote install it on your bike stem or handlebar Using the Mounts page 4 e If you are using the wireless remote pair the devices Pairing the Remote with Your Varia Device page 4 e If you are using a compatible Edge device pair
14. entation of the mount for an Edge device 4 Place a rubber pad around the handlebar e Ifthe handlebar diameter is 25 4 mm use the thicker pad e Ifthe handlebar diameter is 31 8 mm use the thinner pad 5 Place the handlebar connector around the rubber pad NOTE You should align the contours on the rubber pad with the grooves on the inside of the handlebar connector 6 Adjust the mount on the handlebar so the headlight is mounted horizontally parallel to the road 7 Replace and tighten the screw NOTE Garmin recommends a torque specification of 7 Ibf in 0 8 N m You should check the tightness of the screw periodically 8 Align the notches on the top of the headlight with the tabs on the bottom of the mount 9 Press up slightly and turn the headlight clockwise until it locks into place 10 If installing an Edge device align the tabs on the back of the Edge device with the notches on the top of the mount 11 Press down slightly and turn the Edge device clockwise until it locks into place Installing the Seat Post Mount 1 Select a secure location to mount the taillight where it does not interfere with the safe operation of your bike NOTE You should mount the device as high on the seat post as possible for optimal light visibility Verify there is clear space no obstructions behind the device 2 Use the hex key to remove the screw from the seat post connector Introduction Place a rubber p
15. ice Pairing Varia Bike Lights with Your Edge 1000 page 3 2 From your Edge device select X gt Sensors gt Varia gt Turn Signal Setup 3 Select Right and select a taillight to assign it as the right turn signal When two taillights are paired the Edge device assigns the second taillight as the left turn signal automatically A lf necessary select Left and select the second taillight to assign it as the left turn signal Signaling a Turn with Your Edge 1000 The Varia device is not a substitute for other bike safety measures such as hand signals deferring to posted signs and conditions and using good judgement Before you can signal a turn with your Edge device you must install two taillights nstalling the Multi Location Mount page 2 and assign turn signals to them Assigning Turn Signals page 3 1 Go fora ride 2 Tap the screen to view the timer overlay Device Settings 3 Select the left or right turn signal NOTE You can select the same turn signal again to cancel the turn signal Light Network Settings From your Edge device select X gt Sensors gt Varia gt Light Network and select a paired light Enable Turns on the light and allows you to control the light remotely with your Edge device You can disable a light to disconnect it from the light network Motion Activated Automatically turns on the light when the Edge device is in motion Auto Deceleration Automatically adjusts the
16. ough the bike light intensity and pattern modes Taillight modes include smart mode high medium low and flash Headlight modes include smart mode overdrive high medium low and flash NOTE Taillight medium and flash modes are available on the Varia TL 300 device only Headlight overdrive and flash modes are available on the Varia HL 500 device only Hold the device key for 2 seconds to turn off the device The next time you turn on the device it enters the last used operating mode Introduction Device Settings You can remotely control your Varia devices and customize settings using your compatible Edge device This section contains instructions for the Edge 1000 device Other compatible Edge devices use similar settings Pairing Varia Bike Lights with Your Edge 1000 Before you can pair the devices you must update the Edge software 1 Bring the Edge device within range 3 m of the sensor NOTE Stay 10 m away from other ANT bike lights while pairing 2 Turn on the Edge device 3 From the home screen select X gt Sensors gt Add Sensor gt Varia 4 Turn on the Varia device 5 Select the Varia device key to enter smart mode The status LED flashes blue 6 Select your sensor When the sensor is paired with your Edge device the status icon appears solid on the connections page Turning Varia Devices On and Off with Your Edge 1000 Before you can turn Varia devices on and off with your Edge
17. rinctbionedice Bike Eis Same LEI ee ee Using the Device Key essen ansehen een nenne DEVISE SENN S een Pairing Varia Bike Lights with Your Edge 1000 Turning Varia Devices On and Off with Your Edge 1000 Customizing Varia Device Settings with Your Edge 1000 Coniguratlion SERIE een Adjusting the Beam Angle During a Ride TUR a EIER ee Light Network Sellli88 u cnnene nn Testing the Light Network nen Wireless Remote Control cccsccccssseeeessseeeeeseeeeneneenes LV CC EENI A EETA A N T EENE O EE ARE TRIER enn pate eh tna nt wa aa paste nena ames gee Pairing the Remote with Your Varia DeVICE cecceeeeeeeees D i OA EEEE ETE A ETTE Keplacing ING BARON nee Device Information uuu0 u0202n0002n00nannnnnnnnannnnnnn 2460 wm 1 asera Headlight Specifications cccccccsssseececeeeseeceeseseesssseeesens Taillight Specifications vie nn Remote Specifications neun PEVCE O r EET Cleaning ihe DEVICE adc desercnrcccesccadecestee coersaHatover test arseeseentiies Troubleshooting 2un0 n0000n0nn onen nenn nnnnn nn nn Resetting the Device ii cake ciduccbrcausanderuisasaeia seine cadiaseieesuisaniaabined Thermal Safety Shutdown scsi ssid a ictncratevicansccavedesevassaasancicadeava Replacement O ringS cccccccsssececcesseeeceesesecceasseessaeeseessaaeeees SUPPO ana Nie u gt gt See ee
18. rotocol From 0 to 40 C from 32 to 104 F 2 4 GHz ANT wireless communications protocol Water rating IEC 60529 IPX7 Varia TL 300 301 LED luminous flux 22 Im typical in high mode The device withstands incidental exposure to water of up to 1m for up to 30 min For more information go to www garmin com waterrating Taillight Light Intensity Modes Intensity Mode Varia TL 300 Luminous Varia TL 301 Luminous Flux Flux High 22 Im 22 Im Medium 14 Im Not applicable Low 7 Im 14 Im Flashing 28 Im Not applicable Braking 35 Im 35 Im Remote Specifications Battery type User replaceable CR2032 3 V Battery life Up to 1 5 yr at 1 hr day Operating temperature range From 10 to 50 C from 14 to 122 F Device Information 2 4 GHz ANT wireless communications protocol 5 ATM Radio frequency protocol Water rating The device withstands pressure equivalent to a depth of 50 m For more information go to www garmin com waterrating Device Care NOTICE Do not store the device where prolonged exposure to extreme temperatures can occur because it can cause permanent damage Avoid chemical cleaners solvents and insect repellents that can damage plastic components and finishes Secure the weather cap tightly to prevent damage to the USB port Cleaning the Device 1 Wipe the device using a cloth d
19. tempting to pair with a device A turn indicator is on Alternating red and green 12 rapid green flashes Solid red 12 rapid red flashes Successfully paired with a device Pairing failed or the connection was lost A paired device entered power conservation mode The light intensity is automatically adjusted to prolong battery life One or more of the paired devices has a low battery Flashing red Pairing the Remote with Your Varia Device The first time you connect the Varia remote to your Varia device you must pair the remote with your device 1 Bring the remote within 1 m 3 ft of the device NOTE You must stay 10 m 33 ft away from other ANT sensors while pairing 2 On the Varia device hold the device key for 1 second to turn it on 3 Select the Varia device key to enter smart mode The status LED starts flashing blue 4 On the Varia remote hold two keys simultaneously until the status LED starts alternating green and red and release the keys The remote searches for your Varia device After the remote pairs successfully the status LED flashes green 12 times After the remote is paired it connects to your device whenever the device is in range and turned on Using the Mounts Several mounts are available for your remote either included with the product or as an optional accessory The mounts allow you to attach the remote to your body your bike or other objects Align two of
20. the devices Pairing Varia Bike Lights with Your Edge 1000 page 3 e f you are using a compatible Edge device customize the bike light settings Customizing Varia Device Settings with Your Edge 1000 page 3 Charging the Device To prevent corrosion thoroughly dry the USB port the weather cap and the surrounding area before charging or connecting to a computer The device is powered by a built in lithium ion battery that you can charge using a standard wall outlet or a USB port on your computer NOTE The device does not charge when outside the approved temperature range Specifications page 5 1 Pull up the weather cap from the USB port 2 Plug the small end of the USB cable into the USB port on the device 3 Plug the large end of the USB cable into an AC adapter or a computer USB port 4 Plug the AC adapter into a standard wall outlet 5 Charge the device completely The status LED flashes green while charging The status LED is solid green when charging is complete Installing the Out Front Mount You can use the out front mount to install both an Edge device and a headlight 1 Select a secure location to mount the Edge device and headlight where they do not interfere with the safe operation of your bike 2 Use the hex key to remove the screw from the handlebar connector 3 If necessary remove the two screws on the top of the mount rotate the connector and replace the screws to change the ori
Download Pdf Manuals
Related Search