Home

User Manual - LT Security Inc.

image

Contents

1. TURBO HD TVI Turret Camera User Manual Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described inthe manual Please refer to the product specification for camera parameters and functions Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits fora digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any
2. clockwise to secure it to the camera A Figure 2 6 Install the trim ring 2 3 Installation of Type Camera Steps 1 Drill the screw holes and the cable hole on the ceiling according to the supplied drill template 1 Drill Template Hole 1 for mounting base 1 Hole A for cables route through the wall Figure 2 6 The Drill Template 2 Fixthe mounting base to the ceiling with the supplied screws I i eh Figure 2 7 Fix the Mounting Base and Camera 3 Route the cables to the cable hole and connect corresponding power cable and video cable 4 Secure the camera to the mounting base 5 Fix the enclosure to camera 6 Adjust the camera according to the figure below to get an optimum angle Figure 2 8 3 axis Adjustment 3 Menu Operation Menu VIDEO OUT DAY amp NIGHT AWB AE EFFECT system EXIT EE famn Cre Clone CBR CARER USER B W a Csc MOTION Hik ID DISP HOLD AUTO Crow Hie SHARPNESS EXT CONTRAST LANGUAGE 6000K G MIRROR EP Figure 3 1 Main Menu wore A coaxial camera controller purchase separately is required to select the menu and adjust the camera parameters 3 1 VIDEO OUT You can set the frame rate as 25 fps 30fps 3 2 DAY NIGHT Color B W AUTO and EXT are selectable for DAY NIGHT switches Under the mode of the AUTO and EXT you can set the IR LED as Smart and CDS If th
3. maintenance by yourself 2 1 Installation of Type I Camera Steps 1 Drill the screw holes and the cable hole according to the drill template Drill Template Hole 1 for mounting base 1 1 Hole A for cables routed through the wall Figure 2 1 The Drill Template 2 Fix the mounting base to the ceiling with the supplied screws 3 Route the cables to the cable hole and connect the corresponding power cable and video cable 4 Secure the camera to the mounting base 5 Fix the enclosure to camera to complet the installation Figure 2 2 Fix the Mounting Base and the Camera 6 Adjust the camera according to the figure below to get an optimum angle 0 360 S7 Figure 2 3 3 axis Adjustment 2 2 Installation of Type Il Camera Steps 1 Drill the screw holes and the cable hole on the ceiling according to the drill template a Drill Template Hole 1 for mounting base Hole A for cables routed through the wall 1 Figure 2 4 The Drill Template 2 Connect the corresponding power video cables 3 Insert the supplied screws to the screw holes and tighten the screws to secure the camera to the ceiling 4 Loosen the lock screw 5 Rotate the enclosure to adjust the pan angle rotate the camera to adjust the tilt angle 6 Tighten the lock screw to clamp the lens fff Figure 2 5 Fix the camera to the ceiling 7 Attach the trim ring to the camera 8 Rotate the trim ring
4. the area Motion Set the Motion status as ON or OFF Set the SENSITIVITY from 0 to 255 Set the alarm status as ICON TRANCE OFF Set the hold time from O second to 255 seconds HLC HLC supplements the brightness of the peripheral area of the image Youcanset the mask value and threshold from 0 to 255 3 3 6 EFFECT EFFECT 1 COLOR GAIN 200 2 COLOR HUE 200 3 SHARPNESS 25 4 CONTRAST 150 5 BRIGHT OFF 1 6 MIRROR ON 7 FLIP ON 8 RETURN RET Figure 3 5 EFFECT Color Gain Color gain adjust this feature to change the saturation of the color You can set the value from 0 to 255 Color Hue You can adjust the image HUE from Oto 71 Sharpness Sharpness determines the amount of detail that an imaging system can reproduce You can set the value from 0 to 255 Contrast Contrast enhances the difference in color and light between parts of an image You can set the value from 0 to 255 Bright Off Bright Off refers to the brightness compensation of the image You can set the bright compensation value as Oor 1 Mirror You can set the Mirror status as ON OFF Flip You can set the FLIP status as ON OFF 3 3 7 SYSTEM SYSTEM 1 CAMERA ID 255 2 ID DISP ON 3 NAME DISP ON 4 LANGUAGE ENG 5 FACTORY INIT OFF 6 RETURN RET Figure 3 6 SYSTEM You can setthe camera ID from 0 to 255 Select the ID display and name display status as ON OFF Chinese and English are selectable for the la
5. e IR LED is selected as Smart you can set the bright ness of the IRLED DAY NIGHT AWB 1 MODE AUTO MORE AUTO 2 D TON 63 2 R G GAIN 255 3 NTOD 63 3 B G GAIN 151 4 DELAY TIME 20 4 RETURN RET 5 RETURN RET Figure 3 2 DAY NIGHT Figure 3 3 AWB 3 3 3 AWB Auto User Push 8000k 6000k 4200k and 3000k are selectable for AWB Under the mode of AUTO you need to set the R G B G Gain and to select an indoor outdoor mode If the AWB mode is select as User You need to set the R G B Gain manually 3 3 4 AE You can set the AE mode as HOLD DC and ESC Brightness Brightness refers to the brightness of the image Shutter Shutter denotes the speed of the shutter You can set the shutter as AUTO 1 25 1 30 1 50 1 60 1 100 1 120 1 250 1 500 1 1k 1 3k and 1 10k Flicker You can set the flicker status as 5SOHZ 60HZ to prevent image flicking BLC BLC bases on the back area to enhance the brightness of the whole image You can set the BLC gain from Oto 16 AGC AGC optimizes the clarity of image in poor light scene The value of AGC can be set from 1 5 LSC LSC corrects the phenomenon where the image gets darkened or blurred on the periphery 3 3 5 SPECIAL SPECIAL 1 PRIVACY ZONE 2 MOTION 3 HLC 4 RETURN RET Figure 3 4 SPECIAL Privacy Zone Select a PRIVACY area Set the MASK PAT as OFF GRAY WHITE or BLACK Set the SX EX SY EY value to define the position and size of
6. interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the supplied accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European EE Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info 1 Introduction 1 1 Product Features This series of camera adopts new generation sensor with high sensitivity and advanced circuit design technology It features high resolution low image distortion and low noise etc which makes it suitab
7. le for surveillance system and image processing system High performance CMOS sensor and high resolution bring high quality image Low illumination OSD menu parameters are configurable Support auto white balance auto gain control eSupport image effect adjustment Unit transmission control Advanced 3 axis design meets different installation requirements 1 2 Overview 1 2 1 Overview of Type Camera Power Cable Mounting Base HD Video Cable 1 2 2 Overview of Type Camera Camera Mounting Base Trim Ring Enclosure Mounting Base Power Cable Trim Ring HD Video Cable 2 Installation Before you start Please make sure that the device in the package isin good condition and all the assembly parts are included Make sure that all the related equipment is power off during the installation eCheck the specification of the products for the installation environment eCheck whether the power supply is matched with your power output to avoid damage Please make sure the wall is strong enough to withstand three times the weight of the camera and the mounting elf the wall is the cement wall you need to insert expansion screws before you install the camera If the wallis the wooden wall you can use self tapping screw to secure the camera if the product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or
8. nguage of the menu You can restore the camera to the default by setting the factory initialization status as ON 3 3 8 EXIT Exit and Save amp exit are selectable

Download Pdf Manuals

image

Related Search

Related Contents

Chief PTSU flat panel desk mount  USER MANUAL  Char-Broil 2584727  Hygiène de la peau et du sabot  Keramik-Wasserkocher  Descargar - Notifier by Honeywell  Philips Straightener HP4642  Manual - Control Voltage  Heading Level 1 - bathyswath.com  Tricity Bendix DH 101 User's Manual  

Copyright © All rights reserved.
Failed to retrieve file