S9 Welcome Guide
Contents
1. peur AutoSet amp Elite POSITIVE AIRWAY PRESSURE DEVICES H5i HEATED HUMIDIFIER m Welcome Guide sg coe English More Comfort Series Welcome Thank you for choosing the S9 AutoSet S9 Elite or Hbi Before operating these devices please read the entire SD card slot Welcome and Information Guides Module Adapter un DC power inlet Air filter Air outlet S9 at a glance The S9 system comprises the following elements e S9 device e SlimLine air tubing 90W power supply unit e S9 Travel bag SD card e S9 SD card protective folder Optional components include e H5i heated humidifier e Standard air tubing e 30W power supply unit does not support Hbi 1 English Flip lid Air outlet Release button ClimateLine connection port Hbi at a glance rs The Hbi system comprises the following elements tub e heated humidifier e Hbi water tub Optional components include e ClimateLine heated tubing Hbi cleanable water tub Traveling tips When moving or traveling with your HDi e Ensure that the water tub is empty e Disconnect the Hbi from the S9 by using the release button Setup Align your Hbi with your S9 and push them together until they click into place Connect the DC plug of the power supply unit to the rear of the S9 Connect the power cord to the power supply unit Plug the other end of the power cord into the power outlet Connect one end of2. is most comfortable for you To adjust your level of humidity P HUMIDITY LEVEI 1 From your HOME 2 Press amp 3 Turn amp until the 4 Press to screen turn The selection is humidity level confirm your until the HUMIDITY highlighted in that you require is choice LEVEL screen is orange displayed displayed in blue Warming the Hbi The warm up feature is used to pre heat the water before starting treatment To start warming 1 Navigate to the humidity level icon 2 Push and hold for three seconds The Warming Up status bar 15 displayed You can stop warm up at any time by pressing for at least three seconds You can start treatment at any time by pressing Note In order to assist the heater plate in cooling your S9 device will continue to blow air for up to an hour after treatment has stopped However you can unplug the device from the power outlet at any time and allow the heater plate to cool without air flow Adjusting ramp time Designed to make the beginning of treatment more comfortable ramp time is the period during which the pressure increases from a low start pressure to the treatment pressure To adjust your ramp time 2 Press SA until the 4 Press to screen turn selection is ramp time you confirm your until the RAMP highlighted in require is displayed choice screen is displayed orange in blue Using mask fit You can use mask fit to help you f
3. more information on removing and inserting your card refer to your S9 SD Card Protective Folder provided with your device Please retain the S9 SD Card Protective Folder for future use Notes e _ For Troubleshooting information refer to the Information Guide e For more product information see www resmed com Series 368123 Eng 2 09 10 S9 Series AutoSet amp Elite Hbi WELCOME AMER Manufacturer ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia Distributed by ResMed Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA ResMed UK Ltd 96 Milton Park Abingdon Oxfordshire OX14 4RY UK See www resmed com for other ResMed locations worldwide S9 Protected by patents AU 691200 AU 697652 AU 702820 AU 709279 AU 724589 AU 730844 AU 736723 AU 750095 AU 750761 AU 764761 AU 779327 EP 0651971 EP 0661071 EP 0920845 EP 0927538 EP 0934723 EP 1028768 EP 1126893 EP 1144036 EP 1502618 JP 3580776 JP 3778797 NZ 504595 US 5199424 US 5245995 US 5522382 US 5704345 US 6029665 US 6138675 US 6240921 US 6363933 US 6367474 US 6425395 US 6502572 US 6591834 US 6675797 US 6745768 US 6817361 US 6988498 US 7040317 US 7100608 US 7320320 US 7537010 Other patents pending Design registrations pending S9 is a trademark of ResMed Ltd and is registered in U S Patent and Trademark Office H5i Protected by AU 2002233025 CN 7102804936 5 HK 1065483 NZ 527088 US 6935337 Other patent
4. connected Adjust the ramp time or humidification level if required Fit your mask as described in your mask user guide To start therapy simply breathe into the mask and or press O Lie down and arrange the air tubing so that it is free to move if you turn in your sleep To stop treatment at any time remove your mask and or press 9 Notes e f your clinician has enabled SmartStart your device will start automatically when you breathe into the mask and stop automatically when you remove your mask e Once therapy has started the HUMIDITY LEVEL screen is displayed 9 English Cleaning and maintenance You should regularly carry out cleaning and maintenance as described in this section Daily 1 Disconnect the air tubing and hang it in a clean dry place until next use 2 Slide the Hbi latch 3 Lift open the flip lid and remove the water tub 4 Wash the Hbi water tub in warm water using a mild detergent 5 Rinse thoroughly in clean water and allow it to dry away from direct sunlight 6 Before next use fill the water tub return it to the Hbi and close the flip lid Note Do not open the Hbi water tub There are no user serviceable parts inside Weekly 1 Remove the air tubing from the S9 device and the mask 2 Wash the air tubing in warm water using mild detergent 3 Rinse thoroughly hang and allow to dry 4 Before next use reconnect the air tubing to the air outlet and mask Monthly 1 W
5. ipe the exterior of the S9 and Hbi with a damp cloth and mild detergent 2 Check the air filter for holes and blockage by dirt or dust 3 Peelthe flip lid seal from the flip lid and wash it in warm water using a mild detergent Maintenance checklist Inspect the Hbi water tub and flip lid seal for wear and deterioration Replace the water tub if any component is leaking or has become cracked cloudy or pitted Replace the flip lid seal if cracked or torn Clean white powder deposits in the water tub by using a solution of one part household vinegar to 10 parts water KURT Replacing the air filter Replace the air filter every six months or more often if necessary 1 Remove the air filter cover from the back of the S9 device 2 Remove and discard the old air filter 3 Insert a new ResMed air filter ensuring that it is sitting flat in the air filter cover 4 Replace the air filter cover Air filter cover E Air filter J p 11 English SD card An SD card has been supplied to gather therapy data from your S9 device and provide settings updates from your clinician When instructed to do so remove your SD card insert it in the protective folder and send it to your clinician Removing the card 1 Pushin the SD card to release it f Remove the card 3 Insert the card into the protective folder 4 Send the protective folder back to your clinician as instructed P For
6. it your mask properly This feature delivers treatment pressure for a three minute period prior to starting treatment during which you can check and adjust your mask fit to minimize leaks 1 Fit your mask as described in the mask user guide 2 From your HOME screen push and hold amp for three seconds One of the following MASK FIT screens is displayed MASK FIT 3 necessary adjust your mask mask cushion and headgear until you have a Good mask fit After three minutes the pressure reverts to the set pressure and treatment will begin You can end mask fit at any time by pressing 5 English Selecting the mask type To select your type of mask SETTINGS 2 Tube SlimLine Mask Pillows Mask Fit gt lt lt HOME RR 1 Press SETTINGS screen is displayed SETTINGS 2 Tube SlimLine Mask Fit gt lt lt HOME 4 Turn until the mask setting that you require is displayed 2 SETTINGS x Tube SlimLine Mask Pillows Mask Fit gt lt lt HOME Turn until Mask is displayed in blue SETTINGS Er Tube Mask Mask Fit gt SlimLine Full Face lt lt HOME Press to confirm your choice 6 El SETTINGS a Tube SlimLine Mask Fit gt lt lt HOME Press The selection is highlighted in orange Push Dial Af Push to return to the HOME screen Getting started Make sure the power is
7. s pending Designs pending 2009 ResMed Ltd 368123 Eng 2 09 10 Global leaders in sleep and respiratory medicine www resmed com
8. the air tubing firmly onto the air outlet Connect the assembled mask system to the free end of the air tubing Notes e For more information on assembling your mask see your mask user guide e Recommended masks are available on www resmed com on the Products page under Service amp Support Oir m a 3 English Filling the water tub 1 2 3 Slide the latch and lift open the flip lid Remove the water tub Fill the water tub through the center hole with distilled water up to the maximum water level mark 380 mL Return the water tub to the Hbi Close the flip lid ensuring that it clicks into place LCD screen Home menu Start Stop button Starts or stops treatment Key A Humidity level Home e Setup menu Ramp 41 Allows you to 31 make changes Heated tube 8 to settings RR Climate Control Info menu Gem Allows you to Start Stop Q view your sleep statistics Push dial Push dial E gt Turning the dial allows ui you to scroll through m the menu and change Setup menu settings Pushing the dial allows you to enter Info menu i S9 basics into a menu and confirm hoice The control panel of your S9 device includes LCD screen as well a Start Stop button Push dial and the Info and Setup menu keys 5 English Adjusting humidity level Ranging from OFF to 6 you can adjust the humidity level at any time to find the setting that
Download Pdf Manuals
Related Search