PD-300 SERIES - Real Time DC
Contents
1. A type end to USB port of the host Insert the 2 pin or 3 pin power connector from either 12 V AC or 24 V DC power adaptor to the 12 V DC In or 24 V DC In jack in the connector area Insert either end of the power cable to 24 V DC Out jack in the connector area and insert the other end to the power connector of Posiflex POS printer if needed Be sure to hear a click at each connection to obtain a firm contact You may now place the base on a horizontal surface and prepare to power on and adjust the direction of the display head for best viewing effect in application PD 302 1 Aim the bottom center cavity of PD302 series toward the latch stub at rear of TP series main unit as circled in the right picture pam Then aim both metal and plastic hooks at rear of the PD302 series toward the suitable ventilation openings on top rear of the main unit Please use a phillips head sign screw driver to fasten the screws on the metal hook but not to overdo it so that the metal hooks hold the ribs of the ventilation holes from inside 2 Plug the DB9 female connector to the COM port with power DC supply from the TP series Please remove the COM1 terminator and save it at a safe place for future use if COM1 is to be used for PD302 3 Route the cable to go through the notch on back of the stand assembly of touch terminal as indicated in the picture Reassemble the main unit and stand assembly Guidance for future un in2. POS of the Posiflex Product Information CD or download it from web site http www posiflex com tw Download 20list asp Status 1 amp Series_Name U POS amp Model_Name OPOS and execute the file SETUP EXE to install the Part 8 M OPOS Control Manager To add the customer display under OPOS control please set in OPOS Control Manager device name PD3x Line Display in the top row For RS 232 models select the COM port in the 3 row and set baud rate to 9600 in 4 row as in the left sample screen below Select USB in 3 row for USB interface models as in the right sample picture below EE Posiflex OPOS Control Manager v 1 3 2 6 AINEET OII DER FSE PO ScLine Dispay Add Device POSeLine Dipal Add Device DT E D Dero a e Remove Device e Remove Device fom eee ise I Copyright c 1998 Posifexinc f _Replece Device Copyright c 1998 Posiexinc p Replace Device http www posiflex com tw http www posiflex com tw a save save Erama wre C00 z Eaa z F secco a I 4 a Cancel vols a cancel Device Class Device Name Port IP port BaudRate Open Code Logical Name Device Class Device Name Port IP port BaudRate Open Code Logical Name PPTL POS Pinter PP Demo COME 18200 PPTePOS Pinter PP Deno COME 19200 CR Esh Drewes ER Deno come imo pprcrs ERCochbrawer en Deno cone sooo perem MRSA MR Dero MANSA NR Demo CoScare BH Dero com s
3. POSIFLEX PD 300 SERIES E 2 X 20 LCD CUSTOMER DISPLAY Rev DO PD303 FCC Notes This equipment generates uses and can radiate radio PD302 frequency energy and if not installed and used in PD305 accordance with the instructions manual may cause amp interference to radio communications It has been tested i and found to comply with limits for a Class A digital 2 device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial PD306 U PD307 U PD308 U environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference Warranty Limits Warranty terminates automatically when any person other than the authorized technicians opens the machine The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improper application About This Manual Posiflex has made every effort for the accuracy of the content in this manual However Posiflex will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein nor for direct indirect incidental consequential or otherwise dama
4. ale connector pair of the other cable in between PS 2 KB and KB port of the host computer system for power support FOR PD 306U PD 307U PD 308U The power for the USB interface type pole display is supported through the USB connection Therefore there is no need for any operation in the FT series host system However should these customer displays are to be connected through an USB HUB instead of a direct USB port of the system the HUB must be powered by a separate power adaptor otherwise there could be the power shortage problem PHYSICAL INSTALLATION PD 300 PD 300U In base of stand alone models looking from rear side of the bottom the connector area will look like below For PD 300 model To Display head RS232 In 12 VAC In The RJ45 type modular connector is for internal use and is already Part 3 occupied The RS232 input port is a DB9 female connector Connect the attached RS 232 signal cable to this port and one of the COM port in the host system Set the RS 232 communication protocol for this port to 9600 bps no parity 8 bits 1 stop bit with hardware handshaking Connect the power adaptor to the rightmost power connector Turn on the switch in the front side of the base For PD 300U model USB To Display head 24VDCOut 24 V DCIn 12 VACIn The RJ45 type modular connector is for internal use and is also already occupied Connect the B type connector of the interface cable to USB in connector area and the
5. ean CD Scanner BR Demo com 3600 Part 9 SPECIFICATIONS ITEM SPECIFICATION Display type LCD STN positive transflective with back light Number of digits 20 digits row 2 rows Character color Dark blue Back light color Yellow green Wave length 570 nm Max brightness 150 cd m Active display area 142 8 mm W x 20 64 mm H Character height 9 66 mm Character width 6 0 mm Character pitch 7 2 mm H x 10 98 mm V Dot size 1 12 mm H x 1 12 mm V Dot pitch 1 22 mm H x 1 22 mm V Display head size for PD 302 303 305 217 mm W x 80 5 mm H x 28 5 mm D PD 306 308 196 7 mm W x 57 5 mm H x 39 6 mm D Pole height PD 306 8 200 mm Input power type DC Input voltage 5V Current consumption 500 mA max Operation temperature 0 C 50 C 32 F 122 F Storage temperature 10 C 60 C 14 F 140 F POSIFLEX Part 10
6. el to straight up position For both HT and PB system push in the rectangular marked spring button in the same picture mentioned above on both sides of chassis and raise the rear edge of the top cover The COM port DC support for PD 307 can be set at this moment aR Refer to the picture at right of the HT or PB chassis near the right bottom corner as you are facing the HT or PB system from its back with 3 enlarged portions around please find 2 rectangular PD installation holes A on the bottom chassis 2 circular locating holes B on T O plate and 2 circular screw holes C ll on metal sidewall lt Please then refer to the pictures below for the base unit lowest part of PD 307 PD 307U with 2 enlarged portions to the right and a slightly enlarged side view picture to the left to find 2 bottom locking lugs A 2 short cylindrical locating bosses B to fit into I O plate and 2 plastic screw bosses C on side Please note that the PD cable comes out of the bottom end of the base tube yet in the illustration pictures the cable is eliminated for sake of minimum visual confusion Turn the pole display base unit opposite to have the bottom locking lugs A facing left and now insert the 2 bottom locking lugs A on base unit into the 2 rectangular installation holes A on bottom of HT or PB chassis from the right corner with the pole display slightly inclined to the left as in the u
7. external side of sidewall as Outside of sidewall demonstrated in the right picture Carefully close back the top cover of HT or PB system and connect the interface cable of PD 307 or PD 307U to appropriate port in system connector area Then close the back cover of the system To install PD 308 or PD 308U onto FT series host e system the back cover of FT system base has to be opened First push in the circled knobs on both sides as in the right pictures to remove the back cover 2 Remove the pole cover on rear edge of the base top cover of FT system biitiite Liibit by first removing the 2 arrowed screws in the left picture and then pushing the wedge shaped pole cover up 3 Insert the base of PD 308 PD 308U from top of FT system base and screw back the 2 screws as in the right picture Connect the interface cable to appropriate port Stand Alone Model This instruction is for stand alone model only Please unpack the inner box of pole display and it easy to find the base display unit with tube and adaptor separately Please remove the PE foam and bring out the components carefully Firstly place the display head and tube on a flat Part 7 surface and find the cable which in the end of tube Let this cable pass through the short tube which on the base stand and it shows in the picture at right Next please assemble the display head with tube to the base stand which shows in the ri
8. ges including without limitation loss of data or profits resulting from the furnishing performance or use of this material This information is provided as is and Posiflex Technology Inc expressly disclaims any warranties expressed implied or statutory including without limitation implied warranties of merchantability or fitness for particular purpose good title and against infringement The information in this manual contains only essential hardware concerns for general user and is subject to change without notice Posiflex Technology Inc reserves the right to alter product designs layouts or drivers without notification The system integrator shall provide applicative notices and arrangement for special options utilizing this product The user may find the most up to date information of the hardware from web sites http www posiflex com or http www posiflex com tw All data should be backed up prior to the installation of any drive unit or storage peripheral Posiflex will not be responsible for any loss of data resulting from the use disuse or misuse of this or any other Posiflex product All rights are strictly reserved No part of this documentation may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying or otherwise without prior express written consent from Posiflex Technology Inc the publisher of this documentation Copyright Posiflex Techno
9. ght picture Please pay more attention during the process since there is a hole and a compression lock which are in the two side of tube and marked arrow signs Aim these two arrow signs nearby compression lock to the holes and push the tube to the end After hear the click sound the assembly is complete Once combine the display head with tube and base stand please place the pole display as a horizontal position which can easily to check the bottom plate a Please plug the cable to the connector which showing To Display and route the cable as arrowed in the right picture J DRIVER INSTALLATION FOR RS 232 INTERFACE MODELS For direct I O control over the serial interface RS232 models you have to send all commands listed later in this manual under communication protocol 9600 bps none parity 8 data bits 1 stop bit with hardware handshaking on CTS signal to the COM port used No other driver installation is required FOR USB INTERFACE MODELS Copy the driver and library from Posiflex Product Information CD under Drivers PD23_26U to your system or download from web site http www posiflex com tw Download 20list asp Status 1 amp Series_Name P D 20Series amp Model_Name PD 2300U Follow instructions given in the file README TXT to send commands listed later in this manual and data to the customer display under the programming language FOR OPOS APPLICATION Find the subfolder Drivers UPOS O
10. logy Inc 2011 All brand and product names and trademarks are the property of their respective holders P N 19430900070 Part 1 FEATURES Two line LCD display with 20 characters per line Dark blue character with yellow green back light Easy viewing characters 6 0 mm by 9 66 mm Display area 143 mm by 21 mm Euro dollar sign supported in USA European font table Selectable command emulation modes including PST and EPSON command emulation modes Long life trouble free and user friendly operation Composed of several members in the family for versatile applications as tabulated below MODEL NUMBERS 15 30 45 a Rear base low se pole mount to TP KS series ar base pole mount to TP KS series 15 30 45 Rear base pole mount to HT PB series Rear base pole mount to FT series INSTALLATION GUIDE POWER PREPARATION FOR PD 300 PD 300U For these models of customer display it need to be powered by a separate power adaptor Therefore there is no need for any operation in the POS host system The power adaptor for PD 300 supplies 12VAC the power adaptor for PD 300U can either be the 12V AC one or the 24V DC power adaptor for Posiflex POS printer and to support the printer through use of on option cable P N 21863250900 FOR PD 302 PD 305 PD 306 PD 307 PD 308 For these models of customer displays to be used in Posiflex touch terminal systems the internal jumpers of the touch system should be modified t
11. o provide 5 V DC power to the customer display through the specific Part 3 Part 2 interface cable to support the operation of the customer display For PD 302 please separate the main unit of host system TP series from the base and open the service window on back of main unit as described in User s Manual of the system Have a qualified electronic technician to adjust during power off the internal jumper in service window to supply 5 V DC to the COM port selected for the customer display following guide from relevant technical manual For PD 305 and PD 306 same operation as for PD 302 is required for the host system KS or TP series For PD 307 a qualified electronic technician will be required to open the top cover of the base main unit of HT or PB series host system during power off to adjust the internal jumper to supply 5 V DC to the COM port selected for the customer display following guide from relevant technical manual For PD 308 a qualified electronic technician will be required to open the base unit of FT series host system during power off to adjust the internal jumper to supply 5 V DC to the COM port selected for the customer display following guide from relevant technical manual FOR PD 303 There are 2 cables from the PD 303 for application in a host computer system as shown in the right picture The cable with a DB9 female connector is for connection to the COM port of the system for data transmission Plug the male fem
12. pper picture at right Please note that both bottom locking lugs A should be i completely inserted and come out of the bottom plate of HT or PB system as emphasized by an i arrow in the enlarged portion in lower right d eeuna 8 gentle pressure at the bottom end of pole base bottom locking lugs A to the left away from the sidewall of system chassis when moving the upper part of pole toward sidewall as in the left picture 7 Please refer to the right picture taken from inside of HT or PB system to show that the 2 short cylindrical locating bosses B should match into 2 round holes B in the I O plate The bosses B inside holes B are show in the enlarged portion B Part 6 10 PD 308 PD 308U 1 ij Please note the importance of keeping the leftward pressure on bottom end of pole display during the process of turning the pole upright and inserting the locating bosses B or even when you want to release the locating bosses B away from I O plate B and turn the upper end of pole display to left to remove the locking lugs A from bottom chassis A Ignorance of this point may damage or even break off the locking lugs A due to improper torque applied The screw bosses on base of PD 307 PD 307U should now align with the PD 307 Base a screw holes on sidewall of system mi chassis Only 1 screw needs to be applied Use the self tapping screw that comes with PD 307 to fix from i
13. stallation Please use screw driver to release the metal hook before removing PD302 from the ventilation holes X Metal Hook Plastic Hook Part 4 PD 303 1 2 Adhere the two pieces of EVA tape on the metal plates at bottom as indicated in picture at right Peel off the protective covers of the tape to stick PD303 series on a flat and clean surface Apply the screws at 2 arrows in the right picture for firm fixation on counter if necessary PD 305 PD 306 PD 306U 1 PD 307 PD 307U 1 Remove rear connect cover of the KS or TP series terminal system from the base gt eae per instruction of the terminal system Have the cable of PD 305 PD 306 or PD 306U that comes out of its base joint to enter the base of host system through the cable exit so to connect to the main unit Cable Exit Match the base joint of PD 305 PD 306 or PD 306U to the system rear connect area Fit E 2 screws through washers at arrowed points A X in the right pictures to hold the joint tight PD 305 2 PD 306 For ease of PD 307 PD 307U installation operation the HT main unit or PB system has to be opened with sufficient precautions First push in the circled knobs on both sides as in the right picture to remove the back cover Take out the arrow pointed pole cover from it Prepare a piece of clean soft clothe of appropriate size in front of the HT system to prevent damage to the display panel Turn the display pan
Download Pdf Manuals
Related Search