CONNECTOR CONVERSION BOX GT11H-CNB
Contents
1. o fae oo Panel cut area Unit mm inch 2 Mounting on the panel face Fit the Connector Conversion Box from the back side of the panel face and fix it with four M3 screws prepared by user In the Connector Conversion Box thread of M3 6mm 0 23 in depth is cut in each mounting hole Prepare four M3 mounting screws separately while con sidering the thickness of the panel face Connector Thread depth R lt Conversion 6 0 23 Box il 4r sale 100 3 93 m Unit mm inch M3 screw x 4 pieces prepared by user 4 2 Mounting with a mounting bracket 1 Attaching a mounting bracket Attach the provided mounting bracket to the Connector Conversion Box Mounting bracket accessory jounting screw accessory 3 screw x 3 pieces 4 3 Installation requirements for the rear face of enclosure 2 Mounting on the panel face Mount the Connector Conversion Box on the panel face Drill screw holes on the panel face as follows Connector Conversion Box Drill 3 045 V M4 screw and nut x 3 sets prepared by user Mounting Bracket 20 0 78 Unit mm inch Make sure that interfering objects are not located within 100mm 3 93 from the rear face so that the connector of a PLC cable is not hindered To wire the terminal block keep a space of 25mm 0 98 or more on both sides of the Connector Conversion Box _ Thread2. A For safe use e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system aa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJ WORKS 840 CHIYODA CHO HIMEJI JAPAN
3. depth 25 0 98 7 6 0 23 a Panel Qj face 100 3 93 5 Cautions for use For the emergency stop SW the b contact type is used When the Handy GOT is installed and removed with the connector the switch changes ON to OFF when removed which is the same as the state where the emergency switch is pressed Design such as configuring a parallel circuit outside must be taken into consideration to avoid emergency stop while the Handy GOT is being removed Handy GOT Panel face ES 2 Used as control ES 1 O signals of 7 Parallel external ES 2 3 device y power ES 1 A ON OFF Connector Conversion Box 25 0 98 Unit mm inch This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties
4. JY997D24601B JAPANESE ra ata MITSUBISHI chenses ovine sexes CONNECTOR CONVERSION BOX GT11H CNB 37S Side B ENGLISH User s Manual JY997D24601B Manual Number GRAPHIC OPERATION TERMINAL This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and manuals of relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Registration The company name and the product name to be described in this manual are the registered trademarks or trademarks of each company Effective Sep 2008 Specifications are subject to change without notice 2008 Mitsubishi Electric Corporation Date Sep 2008 Safety Precaution Read these precautions before using Before using this product please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The precautions given in this manual are concerned with this product In this manual the safety precautions are ranked as DANGER and A CAUTION Indicates that incorrect handling may cause hazardous conditions resulting in death or severe inju
5. NGER e Some failures of the GOT or cable may keep the outputs on or off An external monitoring circuit should be provided to check for output signals which may lead to a serious accident Not doing so can cause an accident due to false output or malfunction If a communication fault including cable disconnection occurs during monitoring on the GOT communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative A system where the GOT is used should be configured to perform any significant operation to the system by using the switches of a device other than the GOT on the assumption that a GOT communication fault will occur Not doing so can cause an accident due to false output or malfunction Do not use the GOT as the warning device that may cause a serious accident An independent and redundant hardware or mechanical interlock is required to configure the device that displays and outputs serious warning Failure to observe this instruction may result in an accident due to incorrect output or malfunction Incorrect operation of the touch switch s may lead to a serious accident if the GOT backlight is gone out When the GOT backlight goes out the POWER LED flickers green orange and the display section turns black and causes the monitor screen to appear blank while the input of the touch switch s remains active This may confuse an operator in thinking that the GOT is in screensaver mode who then tries to release th
6. OT Not doing so can cause a fire failure or malfunction CAUTION Indicates that incorrect handling may cause hazardous conditions resulting in medium or slight personal injury or physical damage Z CAUTION Depending on circumstances procedures indicated by linked to serious results In any case it is important to follow the directions for usage DANGER e Some failures of the GOT or cable may keep the outputs on or off An external monitoring circuit should be provided to check for output signals which may lead to a serious accident Not doing so can cause an accident due to false output or malfunction If a communication fault including cable disconnection occurs during monitoring on the GOT communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative A system where the GOT is used should be configured to perform any significant operation to the system by using the switches of a device other than the GOT on the assumption that a GOT communication fault will occur Not doing so can cause an accident due to false output or malfunction Do not use the GOT as the warning device that may cause a serious accident An independent and redundant hardware or mechanical interlock is required to configure the device that displays and outputs serious warning Failure to observe this instruction may result in an accident due to incorrect output or malfunction Incorrect operation of th
7. connection between PLCs option Connector Conversion Box GT11H CNB 37S 4 2 Mounting with a mounting bracket 1 Attaching a mounting bracket 2 Attach the provided mounting bracket to the Connector Conversion Box 2 Part Name The name and the function of each part of the Connector Conversion Box are described below Mounting on the panel face Mount the Connector Conversion Box on the panel face e Front Panel Drill screw holes on the panel face as follows 1 Connector for Handy GOT D Sub 37 pin female Front Panel Back Panel Connects a Handy GOT through an external connection cable a Connector Conversion Box 2 4 5 2 Power switch y J Supplies the power to the Hang GOT ied Drill 3 4 5 en this switch is set to ON the power is supplied Mounting bracket Turn off the power when attaching or detaching the Handy GOT acas D T Q 3 Mounting hole for M3 screw Pag BI i Q is Allows to fix the Connector Conversion Box on the panel face directly or g R Kl BE through a mounting bracket o e 8 A wA o e Back Panel a R z RI Lie f i g 8 R ZIS E 4 Terminal block for power supply and operation switches o 0 a ro A 2 Connects the 24V DC power supply and operation switches SW1 to Lay 7 M4 screw a
8. damage caused by factors found not to be the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system sa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN J 997D24601B JAPANESE J ata MITSUBISHI chenses ovine sever CONNECTOR CONVERSION BOX GT11H CNB 37S Side B ENGLISH User s Manual JY997D24601B Manual Number GRAPHIC OPERATION TERMINAL This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and manuals of rele
9. e power externally in all phases Not switching the power off in all phases can cause a unit failure or malfunction Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit CAUTION Do not disassemble or modify the unit Doing so can cause a failure malfunction injury or fire Do not touch the conductive and electronic parts of the unit directly Doing so can cause a unit malfunction or failure The cables connected to the unit must be run in ducts or clamped Not doing so can cause the unit or cable to be damaged due to the dangling motion or accidental pulling of the cables or can cause a malfunction due to a cable connection fault When unplugging the cable connected to the unit do not hold and pull the cable portion Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault DISPOSAL PRECAUTIONS CAUTION TRANSPORTATION PRECAUTIONS CAUTION e When disposing of the product handle it as industrial waste Associated Manuals e The Connector Conversion Box is a precision instrument During transportation avoid impacts larger than those specified in this manual Failure to do so may cause failures in the unit After transportation verify the operations of the unit The following manuals are relevant to this product When these loose manuals are required plea
10. e GOT from this mode by touching the display section which may cause a touch switch to operate Note that the following occurs on the GOT when the backlight goes out The POWER LED flickers green orange and the monitor screen appears blank DESIGN PRECAUTIONS DESIGN PRECAUTIONS Z CAUTION Do not bundle the control and communication cables with main circuit power or other wiring Run the above cables separately from such wiring and keep them a minimum of 100mm 3 94in apart Not doing so noise can cause a malfunction MOUNTING PRECAUTIONS O DANGER Make sure to turn off the Connector Conversion Box s power before attaching or detaching it to from the GOT Failure to do so may cause unit failure or malfunctions MOUNTING PRECAUTIONS N CAUTION WIRING PRECAUTIONS Use the Connector Conversion Box within the generic environment specifications described in this manual If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur DANGER WIRING PRECAUTIONS Be sure to shut off all phases of the external power supply used by the system before wiring Failure to do so may result in an electric shock product damage or malfunctions Please make sure to ground FG terminal of the Connector Conversion Box power supply section by applying 100 or less which is used exclusively for the GOT Not doing so may cause an electric shock or malfunction Correctly wi
11. e touch switch s may lead to a serious accident if the GOT backlight is gone out When the GOT backlight goes out the POWER LED flickers green orange and the display section turns black and causes the monitor screen to appear blank while the input of the touch switch s remains active This may confuse an operator in thinking that the GOT is in screensaver mode who then tries to release the GOT from this mode by touching the display section which may cause a touch switch to operate Note that the following occurs on the GOT when the backlight goes out The POWER LED flickers green orange and the monitor screen appears blank CAUTION may also be DESIGN PRECAUTIONS TEST OPERATION PRECAUTIONS Plug the communication cable into the connector of the connected unit and tighten the mounting and terminal screws in the specified torque range Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit DANGER STARTUP MAINTENANCE PRECAUTIONS Before performing the test operations of the user creation monitor screen such as turning ON or OFF bit device changing the word device current value changing the settings or current values of the timer or counter and changing the buffer memory current value read through the manual carefully and make yourself familiar with the operation method During test operation nev
12. er change the data of the devices which are used to perform significant operation for the system False output or malfunction can cause an accident DANGER STARTUP MAINTENANCE PRECAUTIONS When power is on do not touch the terminals Doing so can cause an electric shock or malfunction Before starting cleaning or terminal screw retightening always switch off the power externally in all phases Not switching the power off in all phases can cause a unit failure or malfunction Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit CAUTION Do not disassemble or modify the unit Doing so can cause a failure malfunction injury or fire Do not touch the conductive and electronic parts of the unit directly Doing so can cause a unit malfunction or failure The cables connected to the unit must be run in ducts or clamped Not doing so can cause the unit or cable to be damaged due to the dangling motion or accidental pulling of the cables or can cause a malfunction due to a cable connection fault When unplugging the cable connected to the unit do not hold and pull the cable portion Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault TRANSPORTATION DISPOSAL PRECAUTIONS Ac AUTION PRECAUTIONS e When disposing of the product handle it as industrial was
13. icable GOTs Abbreviations Model name Operating ambent temperature 0 to 55 C 10 to 90 RH non condensing Operating ambent humidity The wet bulb temperature is 39 C or less In conforms to JIS B3502 and IEC61131 2 5 to 9Hz Half amplitude 3 5 mm 9 to 150Hz Acceleration 4 9m s2 10 times sweeping in each of X Y and Z directions Vibration resistance Must be free of lamp black corrosive gas flammable gas or excessive amount of electroconductive dust particles and must be no direct sunlight Same as for saving Operating atmosphere External Dimensions 82 3 22 37 5 1 47 GOT 1000 GT11 Handy GOT GT1155HS QSBD GT1150HS QLBD bobeos elelslelelele a BOOB OCS o E o Ks 9 Ie 8 0 7 19 5 0 76 4 Installation Weight about 0 17kg Unit mm inch The Connector Conversion Box can be installed on the panel face directly or with mounting bracket offered as an accessory 4 1 Direct mounting on the panel face 1 Direct mounting on the panel face Drill a mounting slot of the following size on the panel face 18 0 7 28 1 1 18 0 7 Drill 4 93 5 a 3 s i w NI g 1 ig e e 3 1 2 N D O 2 1
14. ie A H IS 1 2 B 3 Specifications General Specifications Item Specifications e Front Panel 1 Connector for Handy GOT D Sub 37 pin female Connects a Handy GOT through an external connection cable 2 Power switch Supplies the power to the Handy GOT When this switch is set to ON the power is supplied Turn off the power when attaching or detaching the Handy GOT 3 Mounting hole for M3 screw Allows to fix the Connector through a mounting bracket e Back Panel 4 Terminal block for power supply and operation switches Connects the 24V DC power supply and operation switches SW1 to SW6 of the Handy GOT Terminal block for connection M3 terminal screw provided cover 5 Terminal block for emergency stop switch grip switch keylock switch Connects the emergency stop switch ES 1 ES 2 grip switch DSW 1 DSW 2 and keylock switch KSW 1 KSW 2 Terminal block for connection M3 terminal screw provided cover 6 Connector for PLC RS 422 D Sub 9 pin female Connects the PLC through a PLC cable RS 422 and RS 232 are not available simultaneously Connector model name 17JE 13090 37D23A DDK 7 Connector for PLC RS 232 D Sub 9 pin male Connects the PLC through a PLC cable RS 422 and RS 232 are not available simultaneously Connector model name JES 9P 2A3A JST onversion Box on the panel face directly or Appl
15. nd nut x 1 SW6 of the Handy GOT _ 7 LA x3 sets 4 Terminal block for connection M3 terminal screw provided cover P oe prepared by user a A 5 Terminal block for emergency stop switch grip switch keylock switch Mounting x Connects the emergency stop switch ES 1 ES 2 grip switch DSW 1 Mounti a a Bracket 10 0 39 DSW 2 and keylock switch KSW 1 KSW 2 lounting screw accessory 20 0 78 Terminal block for connection M3 terminal screw provided cover M3 screw x 3 pieces inch nit mm incl 6 Connector for PLC RS 422 D Sub 9 pin female Connects the PLC through a PLC cable RS 422 and RS 232 are not available simultaneously z 7 Connector model name 17JE 13090 37D23A DDK 4 3 Installation requirements for the rear face of enclosure 7 Connector for PLC RS 232 D Sub 9 pin male Make sure that interfering objects are not located within 100mm 3 93 from the rear face so that the connector of a PLC cable is not hindered Connects the PLC through a PLC cable To wire the terminal block keep a space of 25mm 0 98 or more on both sides of the Connector Conversion Box RS 422 and RS 232 are not available simultaneously Connector model name JES 9P 2A3A JST a Thread depth 25 0 98 25 0 98 3 Specifications doss 10 23 General Specifications Applicable GOTs Item Specifications Abbreviatio
16. ns Model name q Operating ambent temperature 0 to 55 C GOT 1000 GT11 Handy GOT GT1155HS QSBD GT1150HS QLBD N Pe 10 to 90 RH non condensing Operating ambent humidity The wet bulb temperature is 39 C or less Da In conforms to JIS B3502 and IEC61131 2 eae 5 to 9Hz Half amplitude 3 5 mm 9 to 150Hz Di Acceleration 4 9m s2 10 times sweeping in each of X Y and Z directions ees a Lowes Must be free of lamp black corrosive gas J 4 J bie J a AY flammable gas or excessive amount of anel Ei Operating atmosphere electroconductive dust particles and must be no face 100 3 93 direct sunlight Same as for saving L 100893 j Unit mm inch External Dimensions 5 Cautions for use 82 3 22 37 5 1 47 For the emergency stop SW the b contact type is used When the Handy GOT is installed and removed with the connector the switch changes ON to OFF when removed which is the same as the state where the emergency switch is pressed Design such as configuring a parallel circuit outside must be taken into consideration 6 E o to avoid emergency stop while the Handy GOT is being removed ia S ga oe W a iS Panel face 2
17. ole ES 2 Used as Weight about 0 17kg ES 1 ie f 18 0 7 19 5 0 76 Unit mm inch signe o This manual confers no industrial property rights or any rights of any other kind extemal nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be 4 Installation ES 2 device held responsible for any problems involving industrial property rights which may The Connector Conversion Box can be installed on the panel face directly or with mounting bracket offered as an accessory PUDFE occur as a result of using the contents noted in this manual 4 1 Direct mounting on the panel face Warranty 1 Direct mounting on the panel face Drill a mounting slot of the following size on the panel face 18 0 7 28 1 1 18 0 7 Drill 4 93 5 25 0 98 60 2 36 91 3 58 ne Panel cut area Unit mm inch 2 Mounting on the panel face Fit the Connector Conversion Box from the back side of the panel face and fix it with four M3 screws prepared by user In the Connector Conversion Box thread of M3 6mm 0 23 in depth is cut in each mounting hole Prepare four M3 mounting screws separately while con sidering the thickness of the panel face Connector Thread depth RXS Conversion 0 23 Box 100 3 93 m Unit mm inch M3 screw x 4 pieces prepared by user Connector Conversion Box Mitsubishi will not be held liable for
18. re the Connector Conversion Box power supply section after confirming the rated voltage and terminal arrangement of the GOT Not doing so can cause a fire or failure Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT Not doing so can cause a fire failure or malfunction Z CAUTION TEST OPERATION PRECAUTIONS Plug the communication cable into the connector of the connected unit and tighten the mounting and terminal screws in the specified torque range Undertightening can cause a short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit DANGER STARTUP MAINTENANCE PRECAUTIONS Before performing the test operations of the user creation monitor screen such as turning ON or OFF bit device changing the word device current value changing the settings or current values of the timer or counter and changing the buffer memory current value read through the manual carefully and make yourself familiar with the operation method During test operation never change the data of the devices which are used to perform significant operation for the system False output or malfunction can cause an accident DANGER STARTUP MAINTENANCE PRECAUTIONS When power is on do not touch the terminals Doing so can cause an electric shock or malfunction Before starting cleaning or terminal screw retightening always switch off th
19. ry DANGER DESIGN PRECAUTIONS Z CAUTION Do not bundle the control and communication cables with main circuit power or other wiring Run the above cables separately from such wiring and keep them a minimum of 100mm 3 94in apart Not doing so noise can cause a malfunction MOUNTING PRECAUTIONS D DANGER Make sure to turn off the Connector Conversion Box s power before attaching or detaching it to from the GOT Failure to do so may cause unit failure or malfunctions MOUNTING PRECAUTIONS Z CAUTION WIRING PRECAUTIONS Use the Connector Conversion Box within the generic environment specifications described in this manual If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur DANGER WIRING PRECAUTIONS Be sure to shut off all phases of the external power supply used by the system before wiring Failure to do so may result in an electric shock product damage or malfunctions Please make sure to ground FG terminal of the Connector Conversion Box power supply section by applying 100 or less which is used exclusively for the GOT Not doing so may cause an electric shock or malfunction Correctly wire the Connector Conversion Box power supply section after confirming the rated voltage and terminal arrangement of the GOT Not doing so can cause a fire or failure Exercise care to avoid foreign matter such as chips and wire offcuts entering the G
20. se consult with our local distributor Manual name Manual Number Handy GOT User s Manual sold separately devices For details of a PLC to be connected refer to the PLC user s manual respectively Bundled Items Contents Model Code Describes the Handy GOT hardware relevant content such as part names external i lt i tae ae Aas H A A JY997D20101 dimensions mounting power supply wiring specifications and introduction to option 09R817 Bundled item Quantity Mounting fitting 1 Mounting screw M3 x8 3 CONNECTOR CONVERSION BOX GT11H CNB 37S User s Manual This manual 1 1 Features The Connector Conversion Box relays the GOT s external D Sub 37 pin connector to the power supply switch and the PLC s connector and terminal block while enabling users to operate the Handy GOT outside the enclosure Handy GOT Panel face External cable option To power supply switch PLC i Le a N Relay cable for connection between PLCs option Connector Conversion Box GT11H CNB 37S 2 Part Name The name and the function of each part of the Connector Conversion Box are described below Front Panel Back Panel 4 5 M v 12am Sic ie O ie A rey o
21. te Z CAUTION e The Connector Conversion Box is a precision instrument During transportation avoid impacts larger than those specified in this manual Failure to do so may cause failures in the unit After transportation verify the operations of the unit Associated Manuals The following manuals are relevant to this product When these loose manuals are required please consult with our local distributor Manual Number Contents Model Code Manual name Describes the Handy GOT hardware relevant content such as part names external dimensions mounting power supply wiring specifications and introduction to option devices Handy GOT User s Manual sold separately JY997D20101 09R817 For details of a PLC to be connected refer to the PLC user s manual respectively Bundled Items Bundled item Quantity Mounting fitting 1 Mounting screw M3 x8 3 CONNECTOR CONVERSION BOX GT11H CNB 37S User s Manual This manual 1 1 Features The Connector Conversion Box relays the GOT s external D Sub 37 pin connector to the power supply switch and the PLC s connector and terminal block while enabling users to operate the Handy GOT outside the enclosure Handy GOT Panel face To power supply switch PLC Doo eik ooo A SBA External cable option opron Nre cable for
22. vant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Registration The company name and the product name to be described in this manual are the registered trademarks or trademarks of each company Effective Sep 2008 Specifications are subject to change without notice 2008 Mitsubishi Electric Corporation Date Sep 2008 Safety Precaution Read these precautions before using Before using this product please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The precautions given in this manual are concerned with this product DANGER A CAUTION and In this manual the safety precautions are ranked as Indicates that incorrect handling may cause hazardous DANGER conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous Z CAUTION conditions resulting in medium or slight personal injury or physical damage Depending on circumstances procedures indicated by CAUTION may also be linked to serious results In any case it is important to follow the directions for usage DA
Download Pdf Manuals
Related Search