Manual-alarma auto- Tomahawk-TW-9010
Contents
1. 13 TOMAHAWK TW 9010 1 CHIRP and flash function enabled 2 CHIRPS and flashes function disabled 7 Switch ignition OFF NOTE If the daily auto start function is enabled the engine will start up immediately after ignition is switched OFF Use your remote control trinket to stop the engine 27 Emergency Arming Disarming 1 For emergency arming A Switch ignition ON engine must not be started B Press button Override 8 times C Switch ignition OFF Parking lights will flash 1 time and siren will sound CHIRP to confirm the function enabling 20 sec later the system will enable security mode NOTE If 20 sec after emergency arming any of security zones is triggered the system will alert you with 4 parking light flashes and 4 siren CHIRPS providing you 20 sec to disarm the car If disarming does not take place the system will enable alarm mode 2 Foremergency disarming A Switch ignition ON engine must not be started B Press button Override 4 times C Switch ignition OFF Parking lights will flash 2 times and siren will sound 2 CHIRPS to confirm the function enabling NOTE Remote control trinkets remain functioning after emergency arming disarming 14 TOMAHAWK TW 9010 28 Remote Start up Preparation for Cars with Manual Transmission To ensure capability of remote start up for cars with manual transmission the gear lever should be in neutral position Before stopp2. 4 CHIRPS to confirm Valet mode enabling LCD will display icon and a melody will play 12 TOMAHAWK TW 9010 In this mode only service functions are available such as auxiliary channels car search call driver etc Also available are re arming function and programming mode To disable this function again press D and VD simultaneously Parking lights will flash 3 times and siren will sound 3 CHIRPS to confirm Valet mode disabling LCD will hide icon and a melody will play 25 Call Driver To enable this function press call button located on antenna transmitter LCD will display icon CAL and a melody will play 26 Override Button Functions Some of TOMAHAWK TW 9010 functions can be enabled without control trinkets To enter this mode do the following 1 Switch ignition OFF 2 Using Override button to select required function A Valet mode 3 times B Daily auto start 4 times C Auto warm up to specified cabin temperature 5 times Switch ignition ON The system will confirm the selected function with siren CHIRPS and LED flashes A Valet mode 3 CHIRPS and flashes B Daily auto start 4 CHIRPS and flashes C Auto warm up to specified cabin temperature 5 CHIRPS and flashes To enable disable the functions press button Override The system will confirm enabling disabling the function with siren CHIRPS and LED flashes
3. system will enable alarm mode for 25 sec LCD will display icon and an alarm signal will sound On triggering any other zone the system will enable alarm mode for 30 sec LCD will display an icon corresponding to the triggered zone see page 3 and an alarm signal will sound ATTENTION To disable the alarm signal press button This will cut alarm mode off but the car will remain secured 22 Panic Mode To enable this function press and hold buttons 4 simultaneously engine must not be started Parking lights will flash 3 times and siren will sound 3 CHIRPS to attract attention to your car 23 Anti Hijack Mode To enable this function press and hold buttons simultaneously Parking lights will flash for 30 sec then the system will enable alarm mode engine starter will be locked LCD will display icon and an alarm signal will sound To disable this mode press button This mode can be also enabled using button Anti hijack Press button Anti hijack car engine must be started Parking lights will blink for 30 sec after which the system will enable alarm mode engine starter will be locked This mode will not be disabled before button is pressed You can also exit this mode by holding button Anti hijack for 5 sec 24 Valet Mode To enable this function press and hold buttons D and D simultaneously Parking lights will flash 4 times and siren will sound
4. 010 33 Programming Trinket pager Functions Buttons used Functions performed Notes 9 Backlight switch On Disabled automatically after 5 sec 8 0 Power saving mode switch ON Trinket pager receiver switched OFF automatically 2 min after disarming Sound Vibration mode toggle hold Clock alarm clock and timer setting mode Clock setting mode hour 1 time Clock setting mode minutes N B Alarm clock setting mode hour 3 times Alarm clock setting mode minutes Alarm clock setting mode ON OFF 5 times Timer setting mode hour 6 times Timer setting mode minutes 0000000 Timer setting mode ON OFF Setting hour minute forward Hold for fast scrolling 0 Setting hour minute backward Hold for fast scrolling F E Alarm clock setting mode Timer setting for 10 min Timer setting for 20 min Dal fg 3 times Timer setting for 30 min T Q 4 times Timer setting for 60 min a Q 5 times Timer setting for 90 min 6 times Timer setting for 120 min 18 TOMAHAWK TW 9010 34 Programming Table Number of Override Confirma Description of function c e cw presses tion 1 1 1 1 CHIRP CHIRPS CHIRPS CHIRPS time 1 short CHIRP Time to stop engine
5. IRPS it means that the system detected and disabled defective zone open door hood boot or hand brake disengaged The system will automatically take this zone for protection as soon as the zone is repaired door hood boot closed and hand brake engaged 5 Arming Mode with Siren Disabled To arm a car without siren sounds all messages and confirmations will be sent by the system to the trinket pager only press button time Parking lights will flash 1 time to confirm entry in security mode doors will close LCD will display icons and You can also switch this mode ON and OFF while in security mode TOMAHAWK TW 9010 6 Auto Arming and Re arming If the auto arming function is enabled then with ignition OFF after all doors are closed the system will alert with 1 long CHIRP and will switch security mode ON 10 sec later see Programming Table Auto re arming function is always enabled in the case when after disarming none of the doors open within 30 sec 7 Immobilizer Mode The immobilizer mode is enabled automatically 30 sec after ignition cut off see Programming Table LED indicator glows continuously in this mode In this mode engine start up with ignition key is not possible To exit the immobilizer mode press button es 1 time or switch ignition OFF and press button OVERRIDE 1 time 8 Disarming To disarm vehicle press button 1 time Parking lights will flash 2 times siren will sound 2 CHIRPS if
6. TOMAHAWK TW 9010 TOMAHAWK CAR ALARMS TW 9010 Two Way Car Alarm System USER MANUAL INSTRUCTIONS FOR INSTALLATION gt CONTENTS USER MANUAL System main features Remote control trinkets LCD features Arming mode Arming with siren disabled Automatic arming and re arming Immobilizer features Disarming Opening closing doors with engine working Two step door opening channel 3 Remote engine start up Remote engine cut off Turbo timer Warming up engine to specified temperature Daily 1 2 4 12 hour automatic start up Remote status scanning Remote boot opening 2nd auxiliary channel Car searching Remote shock sensor disabling Alarm modes Panic mode Anti hijack mode Valet mode Call driver Override button functions Emergency arming disarming Remote start up preparation for cars with manual transmission Programming auxiliary trinkets LED indicator operation modes Trinket pager battery replacement Programming mode Programming trinket pager functions Programming table Description of programmable functions INSTRUCTIONS FOR INSTALLATION Basic installation principles Choosing locations for main units Wire connections Selection of manual or automatic transmission Connection of central lock Setting shock sensor Connection diagram Engineering data TOMAHAWK TW 9010 VO Nooc0oo0oc0co 1 1 101 100 amp amp amp amp amp X X amp amp X X
7. after remote start min 5 10 15 20 2 times 2 short CHIRPS Specified engine temperature for automatic warm up C 5 10 20 30 3 times 3 short CHIRPS Starter operation time for remote start up msec 800 1200 1800 3000 4 times 4 short CHIRPS Engine operation control on order Ver l Ver 2 Ver 3 5 times 1 long CHIRP Time for enabling 2 nd auxiliary channel sec 0 8 10 30 constant 6 times 1L 1S CHIRPS Siren impulse duration msec 100 10 15 20 7 times 1L 2S CHIRPS Cable IGN 2 ON OFF Door closing at remote start up Ver 1 Ver 2 Ver 3 4 8 1L 3S CHIRPS Starter ON delay before gasoline diesel engine start sec 2 10 10 10 9 times 1L 4S CHIRPS Duration of central lock opening closing impulse sec 1 2 3 4 10 times 2 long CHIRPS Two step door opening or 3rd auxiliary 1 2 3 4 channel immobilizer 11 times 2L 1S CHIRPS Safe driving function OFF Ver 1 Ver 2 Ver 3 12 times 2L 2S CHIRPS Auto arming Ver 1 Ver 2 Ver 3 13 times 2L4 3S CHIRPS Cabin lighting delay count sec 1 15 30 45 14 times 2L 4S CHIRPS Time for cabin light switch ON window raising sec Ver 1 Ver 2 Ver 3 Ver 4 15 times 3 long CHIRPS Temperature measurement units type of locking black 1 2 Ver 3 Ver 4 and white cable 16 times 3L 1S CHIRPS Turbo timer OFF 1 min 3 min 6 min NOTE The system confirms selected functions using
8. amming Table 9 TOMAHAWK TW 9010 To disable this function press buttons and Parking lights will flash 2 times and siren will sound 2 CHIRPS to confirm disabling the function LCD will hide icon e and a melody will play Note Automatic engine warming up to specified temperature should be made six times per two hours as maximum Temperature for automatic engine warming up may be set at 5 C 10 20 C 30 C see Programming Table 15 Daily 1 2 4 12 hour Automatic Start up To enable this function press and hold buttons vi and D simultaneously Siren will sound CHIRP to confirm enabling the function LCD will display icon and a melody will play After this function is enabled beginning from the next day the system will automatically start engine at the time of enabling To disable the daily start up function press buttons vi and D Parking lights will flash 2 times and siren will sound 2 CHIRPS to confirm disabling the function LCD will hide icon and a melody will play To enable 1 2 4 and 12 hour start up it is necessary to enable the daily start function and then during 5 seconds to press the respective button on the trinket for hourly start 0 start up every 2 hours for start up every 4 hours D for start up every 12 hours 16 Remote Status Scanning To perform remote status scanning press button Parking lights will flash 3 times to conf
9. amp X amp X amp X amp X X amp X X X X X X TOMAHAWK TW 9010 USER MANUAL 1 System Main Features 5 button 2 side programmable trinket with LCD LCD backlight Vibration mode Anti scanner Anti grabber Programmable trinkets up to 4 items Visual and sound confirmation of functions performed Arming with siren disabled Secured remote engine start up cut off Installation option for cars with automatic or manual transmission Installation option for cars with gasoline or diesel engines Cabin temperature control Auxiliary temperature sensor Automatic engine warm up to specified temperature Daily 1 2 4 12 hour automatic start up Defective area bypass with visual and sound confirmation Two zone shock sensor Remote shock sensor disabling Protection against mis operations Self diagnostics 3 extra channels Anti hijack mode Panic mode Valet mode Doors hood and boot security Trinket pager battery charge indication Trinket pager battery power saving mode Driver calling feature Car searching Clock alarm clock and timer built in trinket pager System status LED indication Central lock built in relay Status memory Two step disarming Two step central lock opening Engine locking Automatic pager active area control Turbo timer TOMAHAWK TW 9010 2 Remote Control Trinkets KG TOMAHAWK TW 9010 3 LCD Features Fig 3 security mode indication silen
10. and grey wire input for hood sensor 4 PIN shock sensor socket Socket for shock sensor 2 PIN Override button socket Socket for button Override 2 PIN LED indicator socket Socket for LED indicator 5 PIN combined antenna socket Socket for combined antenna 4 Selection of Automatic or Manual Transmission Selection of automatic or manual transmission in TOMAHAWK TW 9010 is done using jumper 1 see wiring diagram Jumper closed automatic transmission Jumper open manual transmission 27 TOMAHAWK TW 9010 5 Connection of Central Lock TOMAHAWK TW 9010 has in built power relays for central lock control Wiring for connection of central lock is made in a separate six pin socket Wire colours and wiring diagrams are shown in diagrams 1 4 ATTENTION Please note that impulse duration for central lock control is a programmable function 6 Setting Shock Sensor Setting is the last installation stage of TOMAHAWK TW 9010 alarm system Set shock sensor sensitivity to minimum Gradually increase sensitivity and knock the car body with your palm to check triggering threshold ATTENTION Excess sensitivity may result in a great number of false trigger actions you will be forced to desensitize sensors 28 TOMAHAWK TW 9010 Wire Connections 6 PIN remote start up power socket 6 PIN central lock connection socket 18 PIN main socket 4 PIN shock sensor socket 2 PIN Override
11. button socket 2 PIN LED indicator socket 5 PIN combined antenna socket Jumper 1 Closed automatic transmission Open manual transmission Fig 4 29 TOMAHAWK TW 9010 6 PIN Remote Start up Power Socket Gy as gt ev ra TE M 18 PIN main socket i Starter black and yellow wire solenoid Start ern 4 Blocking relay socket Black and yellow 30A Thick red 12V E od Bine from battery Yellow IGN 1 3 Thin red Q 12V from battery Green IGN 2 Diagram 1 ATTENTION Connect blocking relay socket according to diode polarity shown in diagram 1 Ignition key position Off ACC Ignition Start Wire System power supply wire Starter wire IGN 1 wire ACC wire IGN 2 wire Power circuit supply wire 4 E IGN 3 wire M 5 TOMAHAWK TW 9010 6 PIN central lock connection socket UNLOCK COM LOCK COM UNLOCK NO LOCK NO Blue Pr UNLOCK NC SE LOCK NC 18 PIN main socket Black 7 5A ares Green and black 2 Blue AT Cabin light or window UP 300mA Green and 4 ners Black and red Black and white Auxiliary programmable normally losed normally open blocking lt 300mA Black and yellow a Starter blocking Grey relay 300mA Cf LL lt Yellow and red 7 gt 2nd auxiliary channel 300mA Y
12. ellow and blue 3rd auxiliary channel 300mA 2 step door opening Grey and black To tachometer of oil pressure Yellow and black NAM 1st auxiliary channel 300mA Blue and red Doors Q 12V Orange and violet Hand brake sensor Orange and white Blue and black Violet Orange and grey Diagram 2 31 TOMAHAWK TW 9010 4 PIN shock sensor socket Shock sensor 2 PIN Override button socket Override button 2 PIN LED indicator socket DON LED 5 PIN combined antenna socket Combined antenna Diagram 3 32 TOMAHAWK TW 9010 Connection of auxiliary electric drive Control time 0 8 sec Diagram 4 Central lock positive control Control time 0 8 sec Blue and black Green and black Green and grey Wire 1 3A 12V Diagram 5 33 TOMAHAWK TW 9010 Central lock negative control Control time 0 8 sec Wire 1 3A 12V Diagram 6 Pneumatic central lock Audi Mercedes Control time 3 6 sec 12 Wire from driver s door Diagram 7 34 TOMAHAWK TW 9010 Hand brake Orange and violet Diagram 8 Stop lights Orange and violet Stop light switch 4 Diagram 9 35 TOMAHAWK TW 9010 Temperature auxiliary sensor Orange and grey Hood end switch Diagram 10 36 TOMAHAWK TW 9010 Engineering data Rated voltage 12V Current consumption 15mA Allowable current 6 PIN r
13. emote start up power socket In power supply circuit thick red wire 30A limited with fuse In power supply circuit thin red wire 10A limited with fuse IGN 1 30A yellow wire IGN 2 30A green wire IGN 3 300mA black and red wire Starter wire 30A black and yellow wire 6 PIN central lock connection socket In contact relay circuit for central lock control 20A limited with fuse 37 TOMAHAWK TW 9010 18 PIN main socket Blocking relay contacts 40A Blocking relay service output 300mA black and yellow wire Siren power output 2A grey wire Auxiliary channel 1 output 300mA yellow and black wire Auxiliary channel 2 output 300mA yellow and red wire Auxiliary channel 3 output 300mA yellow and blue wire Size lights power supply outputs 7 5A green black and green yellow wires limited with fuses Output to cabin light 300mA blue wire Temporary intervals Service output permanently armed black and yellow wire 6 66 Auxiliary channel 1 output 1 sec yellow and black wire 38 6 66 Auxiliary channel 2 output programmable yellow and red wire 6 66 Auxiliary channel 3 output yellow and blue wire Impulse duration for central lock control programmable TOMAHAWK TW 9010 0 8 sec 10 sec 30 sec Permanently 0 8 sec 0 8 sec 3 6 sec 30 sec This de
14. ety fuses 4 Hood and boot triggers are cut in places protected against moisture inaccessible with hood and boot closed Triggers should be oiled periodically to avoid jams and corrosion 5 The shock sensor is installed in the cabin an ideal place might be the vehicle centre and secured to the car body metal with self driving screws or pasted 6 It is recommended to solder contacts in connections of ignition starter and other circuits 23 TOMAHAWK TW 9010 3 Wire Connections 6 PIN Remote Start up Power Socket Black and yellow wire starter switch on wire 12V This is an output signal 12V to starting relay It is connected to ignition lock wire where 12V appears in the Starter key position This signal is for engine start up Connect this wire to blocking relay Blue wire An output signal 12V ACC auxiliary equipment It is connected to ignition lock wire where 12V appears in the and Ignition ON key position Thin red wire system power supply wire 12V It is connected to ignition battery terminal via 10A fuse Thick red wire remote start up circuit power supply wire 12V It is connected to ignition battery terminal via 40A fuse Yellow wire IGN 1 wire output signal 12V It is connected to ignition lock wire where 12V appears in the Ignition ON key position and does not disappear in the Starter position Green wire IGN 2 wire output si
15. ger melody stop automatically The run time can be prolonged using buttons vm and by 5 min after each press to 20 min maximum LCD will display time before engine stop TOMAHAWK TW 9010 ATTENTION Remote engine start up cannot be done in the case if 1 Gear lever is not in neutral position 2 Ignition switched ON 3 The hood is open 4 The hand brake is not engaged In any of these occasions siren will sound 4 CHIRPS at a remote start up attempt 13 Remote Engine Stop In the case when the engine was started using remote start up you can stop it by pressing button d Parking lights will flash 4 times siren will sound 4 CHIRPS LCD will hide icon and a melody will play 14 Warming up Engine to Specified Temperature Tomahawk provides for an auxiliary temperature sensor for installation under the hood see Diagram No 10 If this sensor is installed engine start and warm up is performed by this sensor s data otherwise by the cabin temperature sensor data To enable this function press and hold buttons e and simultaneously Parking lights will flash 1 time and siren will sound 1 CHIRP to confirm enabling the function LCD will display icon e and the specified temperature for warm up switch on programmable see Programming Table accompanied with a melody When temperature reaches the specified value for automatic warm up switch on the engine will start for previously programmed time see Progr
16. gnal 12V It is connected to ignition lock wire where 12V appears in the Ignition ON key position and disappears in the Starter position if this wire is available on the vehicle where the system is installed 24 TOMAHAWK TW 9010 6 PIN Remote Start up Power Socket 1 Blue wire central contact for central lock opening relay 2 Blue and grey wire normally open contact for central lock opening relay 3 Blue and black wire normally closed contact for central lock opening relay 4 Green wire central contact for central lock closing relay 5 Green and grey wire normally open contact for central lock closing relay 6 Green and back wire normally closed contact for central lock closing relay 18 PIN Main Socket 1 Black wire system Ensure reliable contact 2 Blue wire wire for cabin light ON or window UP 300mA when disarming arming system programmable 3 Black and red wire IGN 3 output 300mA while remote start up procedure for arrangement of auxiliary ignition circuits This wire may become necessary if ignition lock of vehicle where the system is installed has more than two ignition circuits or for enabling immobilizer by pass modules 4 Black and yellow wire starter lock relay wire 300mA after arming system and or remote start up procedure and or in Anti hijack mode ATTENTION Blocking relay should only be used for blocking starter to prevent engine stop while move
17. ing car engine perform the following procedures 1 eue 2 Press button vu D LCD will display icon Enable car hand brake engine should be started and a melody will play Perform step 3 and 4 within 30 sec 3 Remove key from ignition lock engine should keep on running 4 Open the door get out the car and close the door If all the steps are performed correctly the system will automatically stop the engine if not capability of remote start up will be disabled 29 Programming Auxiliary Trinkets TOMAHAWK TW 9010 provides for recording up to 4 remote control trinkets in its memory To record perform the following Ch queer puc Switch ignition ON engine should not be started Press and hold button Override Wait for 4 CHIRPS to confirm entry in the trinket programming mode Release button Override Press and hold buttons before you hear siren 5 confirming memorization of a new trinket 1 CHIRP for first trinket 2 CHIRPS for second trinket 3 CHIRPS for third trinket and 4 CHIRPS for fourth trinket 15 TOMAHAWK TW 9010 6 The system will automatically exit the trinket programming mode if it does not receive signals from the trinket within 6 sec ATTENTION All un programmed trinkets will be erased from the memory 30 LED Indicator Operation Modes The system displays its status using LED indicator when car ignition i
18. irm data transfer to the trinket pager receiver temperature in the cabin security status etc 10 TOMAHAWK TW 9010 17 Remote Boot Opening To remotely open the boot press and hold button Parking lights will flash 3 times to confirm the boot opening LCD will display icon a ATTENTION This function requires auxiliary connection while installation 18 2 nd Auxiliary Channel To enable this function press and hold button e Parking lights will flash 1 time siren will sound 1 CHIRP to confirm enabling the function ATTENTION This function requires auxiliary connection while installation 19 Car Search To enable this function press and hold buttons simultaneously Parking lights will flash 6 times and siren will sound 6 CHIRPS to show car location 20 Remote Shock Sensor Cut off To enable this function while in security mode press and hold buttons E and x simultaneously LCD will display icon to show that the shock sensor warning zone is disabled Second press on the buttons will disable the shock sensor completely and LCD will display icon 8 To enable the shock sensor press buttons eM and once again 21 Alarm Modes On triggering the shock sensor warning zone light shock parking lights will flash 6 times siren will sound 3 CHIRPS LCD will display icon and a melody will play 11 TOMAHAWK TW 9010 On triggering the shock sensor main zone strong shock the
19. ment 25 10 11 12 13 14 15 TOMAHAWK TW 9010 Yellow and red wire 2nd auxiliary channel wire 300mA Grey and black wire input for tachometer wire or oil pressure sensor Connect to tachometer signal wire or oil pressure sensor wire programmable Blue and red wire input for door sensor 99 Orange and white wire input for boot sensor Violet wire Anti hijack function switch ON wire Anti hijack function is switched ON when appears on this wire Green and black wire parking lights power supply wire It is connected via 7 5A fuse Green and yellow wire parking lights power supply wire It is connected via 7 5A fuse Black and white wire programmable auxiliary blocking normally closed normally open 300mA programmable Grey wire siren output 1 5A Yellow and blue wire 3rd auxiliary channel wire or two step door opening wire programmable A 3rd auxiliary channel 300mA B Two step door opening 300mA Yellow and black wire wire for remote boot opening 300mA 1 sec 26 TOMAHAWK TW 9010 16 Orange and violet wire hand brake wire It is connected to hand brake switch for manual transmission or to stop lights for automatic transmission see diagrams 8 9 depending on car bundling 17 Blue and black wire input for door sensor 66 18 Orange
20. ng immobilizer OFF Version 3 3rd auxiliary channel immobilizer ON Version 4 Two step door opening immobilizer ON 11 Safe driving function Version Doors do not close and are automatically open after ignition ON and OFF respectively 21 TOMAHAWK TW 9010 Version 2 Doors are automatically locked 10 sec after ignition ON and open immediately after ignition OFF Version 3 Doors are automatically locked 30 sec after ignition ON and open immediately after ignition OFF 12 Auto arming Version 1 OFF Version 2 ON without locking doors Version 3 ON with locking doors 13 Cabin lighting delay count The system will secure doors after the specified period 1 sec 15 sec 30 sec 45 sec after pressing button 14 Time for closing windows after vehicle arming or switching cabin lighting ON after disarming Version 1 Switching cabin lighting ON for 20 sec after disarming Version 2 Switching cabin lighting ON for 30 sec after disarming Version 3 Closing windows 20 sec after arming Version 4 Closing windows 30 sec after arming 15 Selection of cabin temperature measurement units displayed on trinket pager or F engine auxiliary blocking type black and white cable Version 1 Measurement units C auxiliary blocking normally open Version 2 Measurement units F auxiliary blocking normally closed Version 3 Measurement units C auxiliary blocking normally cl
21. osed Version 4 Measurement units F auxiliary blocking normally open 16 Turbo timer function 22 TOMAHAWK TW 9010 INSTRUCTIONS FOR INSTALLATION 1 Basic Installation Principles TOMAHAWK TW 9010 vehicle alarm system has a classic connection arrangement First of all before installation disable vehicle power system disconnect battery terminal To choose places for alarm system units follow the principles as below Secrecy of installation Absence of heat and moisture emitting sources near the units Allow for minimal mutual interference between standard vehicle electronics and alarm units ATTENTION Emitting antenna should be installed at a distance from alarm and vehicle control units Try to minimize length of cables 2 Choosing Locations for Main Units 1 An electronic unit for alarm control is installed inside the cabin passenger compartment To achieve maximum range combined antenna for the cabinet should be placed at the highest point without contact with metal parts and electric wires 2 Siren is installed in the engine compartment at a hard to reach place If you use an independent siren ensure access to service key slot The siren should be installed with horn down to escape moisture entry Wire connections should better be done inside cabin for less corrosion 3 All strong current circuits power supply lights central lock etc should be protected with respectively rated saf
22. s switched OFF System status Number of flashes 1 Remote start up mode and Immobilizer mode Glowing continuously 2 Car disarmed Disabled 3 Car armed 1 flash 4 Daily auto start mode 2 flashes 5 Auto warm up to specified temperature mode 3 flashes 6 Daily auto start mode and Auto warm up to specified temperature 4 flashes mode 7 Valet mode 5flashes 31 Trinket pager Battery Replacement If battery charge indicator looks like that E it means the battery is low and needs prompt replacement 1 Open trinket pager battery cover Remove used battery 2 3 Press button Be 4 Insert new battery 5 Close trinket pager battery cover 6 B Press button attery type AAA Alkaline batteries are recommended 16 TOMAHAWK TW 9010 32 Programming Mode To enter the programming mode perform the following 1 Switch ignition ON engine should not be started 2 Press button Override 6 times 3 Switch ignition OFF 6 siren CHIRPS will confirm entry in programming mode Use button Override to select required function Each press means change to the next function The system will indicate selected function with siren 5 Short CHIRP 1 Long CHIRP 5 EXAMPLE 14 button Override presses 2 long and 4 short CHIRPS function 14 is selected See numbers and descriptions of functions in Programming Table 17 TOMAHAWK TW 9
23. siren CHIRPS L long CHIRP S short CHIRP Function is confirmed using the following siren CHIRPS CHIRP p _ 2 CHIRPS 3 CHIRPS a 4 CHIRPS ATTENTION Factory settings for programmable functions are underlined 19 TOMAHAWK TW 9010 35 Description of Programmable Functions 1 Time allotted for engine running after remote start up 5 10 15 20 min 2 Engine temperature when automatic warm up is switched ON if the function is enabled 5 10 20 30 C 3 Time for starter operation when remote start up function is enabled 800 1200 1800 3000 ms Time for the first start up attempt is specified If first attempt fails the system will increase time for each three subsequent attempt by 200 msec ATTENTION Set starter operation time for 3000 msec only when engine operation is controlled by tachometer 4 Engine operation control versions Version by vehicle network voltage Version 2 by oil pressure sensor Version 3 by tachometer ATTENTION If you choose 3rd version of engine operation control it is necessary to program idle run RPM as follows 1 Disconnect all power users on the vehicle such as conditioner radio and tape recorder amplifier 2 Switch ignition ON and press button OVERRIDE 9 times 3 Switch ignition OFF Siren will sound 9 CHIRPS and LED will give 9 flashes Wait for the LED to glow 4 Start engine wi
24. t security mode indication closed central lock indication open central lock indication open door s indication open hood indication open boot indication parking lights flashing indication TOMAHAWK TW 9010 Io 9 9 1 11 power saving mode indication trinket pager transceiver operation indication t indication for presence in active zone Qo lt gt gt 12 driver call indication 13 warm up to specified temperature mode indication 14 daily auto start indication 15 light shock indication 16 strong shock indication 17 1 shock sensor warning zone disabling indication 17 2 shock sensor disable indication 015151515069 18 Anti Hijack mode indication 19 vibration mode indication 20 Valet mode indication TOMAHAWK TW 9010 2 21 hand brake disengage indication pe LI 22 started engine indication 23 battery level indication 24 X timer switch on indication 23 alarm clock switch on indication AM e 26 al 8 68 clock 21 temperature measurement units C or F 4 Arming Mode To arm a car I is necessary to press button et 1 time Parking lights will flash 1 time siren will sound 1 CHIRP to confirm entry in security mode doors and windows will close if connected LCD will display icons In case when siren sounds 3 CH
25. th ignition key 5 After engine speed reaches 500 1500 RPM and the engine is warmed enough go to the next step 6 Press and hold button OVERRIDE 1 time If the procedure is successful the system will sound 1 CHIRP otherwise it will alert with 4 CHIRPS of the necessity to repeat the procedure 20 TOMAHAWK TW 9010 5 Enabling impulse length for 2nd auxiliary channel 0 8 10 30 constant 6 Siren impulse klaxon duration 100 10 15 20 msec 7 Wire IGN 2 ON OFF see wiring diagram and door auto closing at remote start up Version IGN 2 ON locks do not close automatically at remote start up Version 2 IGN 2 OFF locks do not close automatically at remote start up Version 3 IGN 2 ON locks close automatically at remote start up Version 4 IGN 2 OFF locks close automatically at remote start up 8 Starter switch on delay before remote engine start up 2 sec for gasoline engines 10 sec for diesel engines 9 Enabling impulse length for central lock Version Closing impulse 0 8 sec opening impulse 0 8 sec Version 2 Closing impulse 3 6 sec opening impulse 3 6 sec Version 3 Closing impulse 0 8 sec 2 opening impulses 0 8 sec Version 4 Closing impulse 30 sec opening impulse 0 8 sec 10 Choice of functions 3rd auxiliary channel or two step door opening immobilizer Version 1 3rd auxiliary channel immobilizer OFF Version 2 Two step door openi
26. the system is not in security mode with siren disabled to confirm disarming doors will open and lighting will go in if connected LCD will display icon 9 Door Opening Closing with Engine Working If the car engine was started with ignition key then you can open and close doors with button LCD will display icons and respectively TOMAHAWK TW 9010 10 Two step Door Opening or Channel 3 These functions are not available at the same time Use Programming Table to select one thereof 1 Two step door opening function is selected Press button to disarm and open the driver s door Second press and hold of this button will open other doors 2 Auxiliary channel function is selected Press and hold button G to enable an auxiliary supplementary channel ATTENTION These functions require additional connection while installation 11 Turbo Timer Tomahawk TW 9010 provides a turbo function for vehicles with turbo engines If this function is enabled the engine keeps on running after ignition OFF for 1 3 or 6 min see Programming Table 12 Remote Engine Start up Press button Parking lights will flash 3 times siren will sound 3 CHIRPS LCD will display the following icons 1 8 engine start up attempt 2 SP if engine fails to start for any reason The engine will run during pre programmed time see Programming Table after which will engine started accompanied by trinket pa
27. vice meets weather requirements under GOST 15150 for UHL 2 version installation inside cabin This device meets electric compatibility requirements under GOST R50789 95 39
Download Pdf Manuals
Related Search