Home

Farm-Center

1. Min Cold system parameters gt Min Max Level control DSFT Soft Min by days soft Min temp Out Control by outside temperature soft Min Band 2 2 C Differential below heat temperature HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 21 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center TARGET TEMP 23 C Min Warm Levels HEAT TEMP 21 C Curve between min warm amp min cold levels SOFT TEMP 19 C Min Cold Levels If the inside temperature is above 21 C heat temperature the controller will operate according to the Min Warm levels If the inside temperature is below 19 C Soft Temp the controller works according to Min Cold levels When the temperature is between 21 C and 19 C the controller creates a curve between the Min Cold and Min Warm levels For example in 20 C the controller operates in level 5 HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 22 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center Important When using Soft Min according to inside temperature there i
2. Daily consumption Y CHANGE Change from previous day HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 43 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center Feed FEED 01 DAY Growth day DAILY Daily consumption Y CHANGE Change from previous day Mortality MORTALITY 01 DAY DAILY TOTAL DAY Growth day DAILY Daily mortality TOTAL Mortality total since growth day one Heater HEATER ROOM 01 The history heater will show the amount of HH MM the heater was on that day HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 44 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Alarm ALARM 01 MESSAGE Press Fail High Temp niab The following is an example of an Icon status that indicates activation of alarms LI NOT ACTIVE AN ALARM THAT WAS RESET M ACTIVE There are 21 different possible alarm messages 10 Gor Soe N a Ana In Fail analog input failure High Temp high temperature alarm Low Temp low temperature alarm Hum Sen Fail humidity sensor failure L
3. Press high t 0 12 Out Temp High set outside high Tunnel press 0 08 temperature definition for high pressure Low alarm 0 05 target High alarm 0 15 3 Press High T Static pressure target for Band 0 04 _ outside high temperature See graph below Wind delay s 10 point 2 Pre open s 9 Tunnel Pressure Static pressure target Alarm MINIMUM level 0 during tunnel ventilation mode Low Alarm If static pressure drops below set point alarm will be active High Alarm If static pressure rises above set point alarm will be active Band Set band zone to balance the system Wind Delay Static pressure is affected by wind this definition is to ensure that an alarm is given due to a stable change in pressure and not an accidental one that may have been caused by a wind gust e2e200000020000000080000000000800800000800808080808 088888088 80 High Alarm Pressure a 8 m mee Tunnel Pressure Static Pressure COC CCC oo e EEE oO LCC ECOL CCC OO C CCC 6 6666666666 6 6 6 s LOW Alarm Temp Pre Open Time setting for curtains to open before fans activate This is to make sure the curtains are open before fan activity Alarm minimum level from what level you wish to activate low static pressure alarm HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 24 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc fo
4. initiate heat lamps Temp Band 1 0 Default 0 0 Humidity Band 2 0 Heat Offset Use this parameter to change the offset F OSGERS Heat temperature up or down for any purpose From Level U Temp Band 1 0 Default 0 0 Humidity Band 2 0 VAR FAN Freeze Protect NO Min Fan 1 Spd 30 Min Fan 2 Spd 30 Min Fan 3 Spd 30 Min Fan 4 Spd 30 HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 25 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center MIN MAX Curve If Yes Min max table curve between the days Default NO Will work according to previous line until current day Level Control Four options for the min max table method by days soft minimum by days by time soft minimum by time Default Day Soft Min Temp choice whether to use the current inside temperature or the outside temperature to determine when to use the soft minimum Default OUT Soft Temp Band diff below heat temperature to set temperature at which to enforce low temperature minimum ventilation level Default 10 0 PRESSURE Press Control Yes No If a pressure control should be done in Min Vent mode by the inlet and in Tunnel mode by tunnel curtain select Yes Otherwise select No Default No LEVELS
5. 2 DEVICE Vent Levels VENT LEVELS 01 12345678 on Off 30 240 40 220 G Munters The Farm Center provides up to 30 programmable ventilation levels The usual way to program them is to start the first level with the least amount of air to be used The full circles represent continuous fan operation each stage S A dot represents no operation at all The following table is an example of a proper ventilation setting The half full circle represents cycle operations according to the on off time set for Note that tunnel is not noticeable on the current table and is set according to the system parameter 1 tunnel level HC MIT UmGB 1557 05 09 Munters Europe AB 2009 Munters reserves the right to make alterations to specification s quantities etc for production or o ther reasons subsequent to Farm Master amp Farm Center User amp Installation manual for pigs publication 29 61 Farm Master amp Farm Center Tunnel Fans pape pe pop pp pp 0580010 3jeje 52 548 00 p4 fete 70 530 00 p5fe e 90 510 00 ee ae ee a a S H H H H e oo SEE TU 230 00 jeje 90 210 00 jeje J 120 180 00 SE a te 149 0 0 nape pe pep pp 300 ioo HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs Munters Europe AB 2009 Munters reserves the right to make alte
6. 34 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Foggers The Foggers table provides settings for the fogger system There are up to 5 fragments allowing precise control over this system Several fragments can be selected for the same day Foggers 01 E From A FROM HH MM Start time TO HH MM End time DIFF Differentiation from target temperature to activate foggers When temperature raises diff above target fogger s process will begin When temperature reduces back to target fogger s process will stop RH As long as the humidity Band are below this level the foggers operates Foggers stop only at humidity level band See figure below ON OFF sec On Off cycle by seconds HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 35 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Light Set the on off times according to growth day there are up to five programmable lines Feed Per Fon Set from what hour to what hour you want the feeding to take place there are up to five programmable lines Extra System EXTRA SYSTEM
7. In that t th t tti b aa SAn Tas eiee apoo 00 vents are at 100 if pressure requires 29 ojojojojf 100 p the Master will open the tunnel curtain to maintain the pressure setting HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 32 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Circulation Fan CIRCULATION FAN 01 Sensors Dif 3 0 From Time 00 00 H 3 To Time 3 00 00 BE From Level 1 To Level 10 The circulation fans will mix the air inside the house and control temperature differentials between different parts of the house Sensors Dif the circulation fan will start if the difference between temperatures in different parts of the house will be higher then the set differential The sensors that participate in this differential can be divided in to 3 groups 1 If no sensors are set for circulation fans in temp definition the current defined sensors will control this operation If for example the house is in tunnel mode the tunnel sensors will control the circulation fans If there will be difference higher then 3 like the example above between 2 sensors the circulation fans will begin to operate 2 If one sensor is defined for the circulation fans the difference between this sensor and the average
8. Inc Delay Time this is the standard minimum delay before increasing ventilation levels Default 120 sec Dec Delay Time this is the standard minimum delay before decreasing ventilation levels Default 180 sec HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 26 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center TUNNEL 1 Tunnel Level switching into and out of tunnel ventilation is a major change in ventilation For tunnel ventilation enter the first tunnel level here If set on O there is no tunnel level Default O Dif Below Exit this parameter sets amount below the tunnel entry temperature at which to exit tunnel ventilation Tunnel temperatures are determined by the sensors specified in Temperature Definition Entry and exit is also controlled by these sensors The controller can not exit tunnel until the tunnel temperature is this much less than the tunnel entry temperature It must be a positive number Default 2 0 T Out Dif Exit set the relative temperature for the outside sensor at which to exit tunnel The controller can not exit tunnel until the outside temperature is less than tunnel temperature plus this differential This number can be positive or negative To eliminate the effect of this paramet
9. None e Heater 1 2 e Heat lamp 1 2 e Fan 1 8 e Cool Pad e Foggers e Curt 1 4 open e Curt 1 4 close e Tunnel open e Tunnel close e Inlet open e Inlet close 6 Light e Feed e Circulation e Extra system 1 3 e Timer 1 5 HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities ete for production or other reasons subsequent to publication 48 61 Farm Master amp Farm Center V Munters Sensors Layout ANALOG INPUT 01 OPTIONS IN NONE oo IN NONE IN NONE NO YES OUT The Sensor Layout accommodates up to 4 temperature sensors and one humidity sensor 3 can be defined for use inside the house and up to one can be used out of the house Just mark IN for a temperature sensor connected in the house and OUT for a temp sensor outside of the house Note only sensor number 4 can be Out Digital Input DIGITAL INPUT 01 There are 3 digital inputs and a selection between water feed aux alarm or none AUX ALARM Once operating function a digital input is sent to make sure that it is actually on and if not the alarm starts Analog Output ANALOG OUTPUT 01 FUNCTION 0 100 1 Var Heat 1 0 0 10 0 2 Var Heat 2 0 0 10 0 3 3 Var Fan 3 3 4 Var Fan 4 Use the Round Arrows key to run through the list of outputs and press enter to select an
10. building to building runs connect the shield to ground at one end only to reduce the chance of conducting lightning from one building to another 6 When splicing sensors to longer wires ensure that the splice is waterproof Use adhesive lined heat shrink marine grade to make waterproof connections 7 Use a good compression connector for splicing This is better than soldering Do not simply twist wires together and then cover with electrical tape 8 Keep sensor wiring separate from other power distribution and high voltage wiring Ensure that lightning on other wiring will not transfer to the sensors 9 Install outside temperature sensors so that the sun will not cause false readings and so that exhaust air from the building will not affect the sensor HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 54 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center Installation and Electrical Connections 1 Install computerized electronic controls at least one meter three feet away from interference sources such as high voltage wiring to motors variable speed light dimmers relays 2 Install electronic controls in a separate ventilated control room that is protected from extreme temperatures and dirty environments Place the controls so that t
11. high temperature alarm when outside temperatures are WATER high like noontime in desert countries Ensuring you Min Water hour U won t get an alarm just because it s a hot day The Max Water hour U emergency temperature has no compensation so the FEED compensation feature only works when temperatures Min Feed hour U do not exceed the emergency temperature Max Feed hour 0 Example Outdoor comp gt Alarm then Alarm Aux Alarm Outdoor Comp A REE L E a For example IF the pre set compensation is 1 C the outside temperature is 24 C and alarm is set to 25 C the controller adds the outside temperature to the comp and the alarm will rise to 26 25 1 26 Out temp Compensation Emerg Alarm 2 Target Emergency Temp The temperature beyond which the controller goes into emergency mode and an alarm is activated LOW TEMP Variable Speed Stop Yes No When in low temperature alarm decide whether to keep variable speed in minimum operation or totally shut down the function WATER amp FEED Min Max Water Hour A quantity of water per our above which alarm will activate Min Max Feed Hour A quantity of feed per our above which alarm will activate AUX ALARM e When assigning a related function alarm occurs if the associated digital input fails to follow the relay Digital input must be active when its associated relay is on e If there is no related function the
12. right to make alterations to specifications quantities etc for production or other reasons subsequent to publication 4 61 Farm Master amp Farm Center 3 MANAGEMENT Animal Inventory Day amp Group Alarm setting Alarm Reset Version Read From Plug Write To Plug 4 HISTORY Temperature Humidity Water Feed Mortality Heater Alarm Event 5 CALIBRATION Temperature Humidity Pressure Water amp Feed 6 INSTALLATION Relay Layout Sensors Layout Digital Input Analog Output Variable Speed Fan Sensor Definition Curtain Setup HC MIT UmGB 1557 05 09 Munters Europe AB 2009 Farm Master amp Farm Center User amp Installation manual for pigs Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication 5 61 Farm Master amp Farm Center Farm Masters Cold Start Set Unit Number Main Menu Calibration Test Technical Specifications Farm Master Installation Guide Mechanical Installation Guide Metal Sheet Assembly Diagram Farm Master Wiring Diagram 1 Communication Wiring Diagram HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication 6 61 Farm Master amp Farm Center V Munters General This
13. the added convenience of eight output relays as well as four analog outputs Each Farm master can operate independently in case of Farm center malfunction or loss of power Using an internal battery when the Farm master is operating alone there is no history collection or possibility to change parameters HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 9 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center Features Farm Center Easy programming LCD 4x20 characters Positioning scrollbar Swift device and feature selection Data plug Large numeric keypad Communication with up to ten Farm Master units Extensive history of events amp alarms Data Collection Real time visual outlook Alarm system for every Farm Master unit Multi language Support G PC communication Farm master Easy programming Programmable outputs Alarm system Large display Up to 3 temperature sensors Up to 8 heavy duty relays 1 HP On Off Auto override switches Static pressure control optional 4 Analog output 0 10 volts Variable speed fan output with bypass Water feed and humidity control G Automatic calibration of curtains HC MIT UmGB 1557 05 09 Farm Master amp Farm Center Us
14. your local MUNTERS dealer Components Farm Center Farm Master Extension Box optional MUX 485 Communication optional General Description Farm Center The Farm Center provides you maximum capability with minimal complexity in programming and controlling up to 10 Farm Master units The Farm Center provides you maximum capability with minimal complexity in programming and controlling up to 10 units Farm Center is the ultimate pig house controller Equipped with an easy programming interface it provides programmable outputs for all major features and a 4x20 character LCD that provides display feedback on the programming and device status The Farm Center communicates with up to ten Farm Master units to access history collect events and alarms for each and all relevant data up to 100 days HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 8 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Farm master Farm master is MUNTERS s latest advance in environmental controllers specially designed for the pig house industry The user friendly has high performance and quick response time Farm master features accurate temperature and humidity sensors secure transmission of data even in noisy environments and
15. 01 Any relay can be set as an extra system There are up to 3 functions relays available to program as extra system The extra system s relays will activate according to the settings in this table and regardless of the conditions or other devices FROM HH MM Start time TO HH MM End time To From Temperature From T To T the temp range for extra system activity ON OFF sec On off cycle by seconds This table consists of up to 5 programs HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 36 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center Time Clocks TIME CLOCKS 01 This is a simple device definition table with operation time and cycle There are up to 5 functions relays available to program as time clocks HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 37 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Variable Heat VARIABLE HEAT 01 Heat1 Heat2 Ht Diff 0 0 0 0 Band 10 0 10 0 Min 30 30 Max 100 100 End Day 0 U Heat Diff Differential from heat temperature to initi
16. 01 FAN 1 30 FAN 3 n a FAN 2 40 FAN 4 n a Hot key 8 Variable Heat VARIABLE HEAT 01 HEAT 1 70 HEAT 2 n a Hot key 9 Relay Status G Munters This screen shows the number of steps for each curtain This screen shows if humidity treatment is ON OFF if the cycle is ON OFF and how many seconds left for the current cycle This screen shows the speed percent of each variable fan This screen shows the percent of each variable heat This option shows active relays pressing 9 again will open the extension box s RELAY STATUS 01 R1 O R2 R3 O R4 m RS5 O R6 O R7 O R8 0 EXTENSION RELAYS Q HC MIT UmGB 1557 05 09 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities Relay Active i Relay Not Active Farm Master amp Farm Center User amp Installation manual for pigs 16 61 relay activity etc for production or other reasons subsequent to publication V Munters Farm Master amp Farm Center Hot key Round Arrow key History Temp This option shows a summary of temperature according to temperature room This screen consists of the following columns Day number Day column Minimum value measured on that day Min column Average value calculated on the measured temperatures through the whole day Avg column Maximum value measured on that day Max column TEMPERATURE ROOM 1 MIN AV
17. G MAX 21 4 23 5 24 5 21 8 24 6 24 HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 17 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities ete for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Farm Center Setup e In order to reach the Farm Center Setup screen go to Room key then press 0 and Enter from any of the main screens The Farm Center setup is a procedure for customizing the Farm Center and Farm Master units to match the system Farm Center COMM Farm Center PC Baudrate Total Rooms Language Language gt English UNITS Temp gt F Press gt IN W C Other Units IMPER OUT TEMP From Room gt 1 T IME Time hh mm PASSWORD Full Access Read Only Parameters are explained in the table on the following page HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 18 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Farm Center identity Max 32 Define the Farm Center s FARM CENTER unit number If only one Farm Center exists the unit number is 1 Otherwise the unit numbers are sequential ees Pere BAUDRATE select communic
18. If you have more than one room don t forget to change room number and install the rest 7 Farm Center Calibration Calibrate your equipment on each room using the service menu 8 Farm Center Control Follow the instructions from page 20 regarding the control parameters for each room 9 Farm Center Device Follow the instructions from page 29 regarding the device settings for each room 10 Farm Center Management Follow the instructions from page 39 regarding live stock and alarm management for each room The History menu is for viewing purposes only HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 11 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center Farm Center Keyboard ooo oe 220 elo Keyboard Functions A Menu Toggles the menu function The room key is used to switch between rooms Press the room key and press a number to reach the desired room C Use the arrows to scroll a short press in any direction moves one notch Round The Round Arrows key is used to scroll between options Arrows Yes No On Off and E Enter The enter key is a confirmation key Numeric The Number keys are selected when a numeric choice is Pad done and when numbers should be selected Moreover those keys are used for H
19. MAROA Siiri ra Jeene pisa Analog Outputs b bY E Output Output f Relays 1 4 Relays 5 8 Variable i d Potent N Spee Se SCEKRSB See FanjHeater pias Analog i Inputs 1 3 Outputs i FHS 10 Humidity Sensor HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 59 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center v Munters Communication Wiring Diagram hio dem Farm Center COM W tA Pre wlons Foom Pom E E E E Shield Shek K cow pected to Sen i connected GHD on hy on ope dto ct d each pkce of cable eee HC MTT UaGR T5ST 0nS 700 amm Master amp Farm Center User amp Installation manual for pigs pni Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication V Munters Munters Europe AB HumiCool Division Kung Hans Vag 8 P O Box 434 SE 191 24 Sollentuna Sweden Phone 46 0 8 626 63 00 Fax 46 0 8 754 56 66 Munters Italy S p A Strada Piani 2 1T 18027 Chiusavecchia Italy Phone 39 0183 52 11 Fax 39 0183 521 333 www munters com Austria via sales organization in Germany Munters Euroform GmbH Phone 49 0 241 89 000 Fax 49 0 241 89 005 189 Denmark via sale
20. TERS warrants that during said warranty period any item items or part parts of equipment found defective with respect to materials or workmanship or which do not conform to the technical specification shall be repaired or replaced at MUNTERS s sole discretion free of charge 4 During the warranty period in the event of an alleged defect authorized resellers in relevant regions should be notified as soon as possible from the date of noticing the said defect but no longer than thirty 30 days from such a discovery The report shall include 1 a short description of the defects noticed 2 type of card component and its matching serial number 5 MUNTERS s sole liability under this warranty is the repair or replacement of the defective item of product Conditions and Limitations 1 MUNTERS will not be responsible for any labor costs or expenses associated with replacement of defective items or other parts of the product or repair 2 This warranty shall not cover i product or part therein which has been modified without prior written approval of MUNTERS or ii product or part therein which has not handled or installed by an authorized reseller of MUNTERS or ili product or part therein which has either handled or installed not in strict accordance with MUNTERS s instructions iv products which were used for function other than agriculture industry 3 This warranty will not apply in the following cases i if all components of the
21. Tunnel 60 60 Inlet 60 DU HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 50 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities ete for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center Farm Masters Cold Start In order to execute a cold start disconnect the power then reconnect the power while pressing the 3 buttons of the Farm Masters together and hold them for about 3 seconds The following will appear When this screen appears the controller preformed a cold start e Cold start will erase all data and history from the memory and load factory defaults Set Unit Number Press the two arrow key simultaneously until NO is blinking Set the unit number with the up and down arrows and press Select Main Menu Once the Farm Master is activated the main screen will appear showing the inside average temperature of the rooms Pressing SELECT for 2 seconds allows the user through the main screen s information trg The target temperature for the room Can be changed from the Farm Master itself only if a curve was not defined rH Humidity in room rH t Target humidity day Growth day for the room The display alternates between the name and the figure HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 51 61 Munter
22. UG PLEASE WAIT HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 41 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Write To Plug Gold data plug SELECT SETTING 1 Room No 1 NO lt YES 2 Room No 2 3 lt NO SETTING gt Write to Plug 4 Use the arrow keys to shift from NO to YES and press Enter to write over the data plug You can name your current configuration by using the arrow keys On the gold data plug select no setting to create a new setting or overwrite an existing one ENTER SETTING NAME Name Room No 1 To Change ARROWS OK gt ENTER Abort gt MENU Press enter to load data to the plug HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 42 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters 4 HISTORY lt Note gt The history section maintains a memory of activity of the last 100 days and 100 events or alarms Temperature TEMPERATURE 01 Sensors Data collection for minimum maximum and average in temperature and humidity for the last 100 days DAY Growth day DAILY
23. User amp Installation Manual CCL5020 CCL5050 Farm Master and Farm Center Pig controller system HC MIT UmGB 1557 05 09 Munters Europe AB 2009 V Munters G Munters Farm Master amp Farm Center Disclaimer Munters reserves the right to make alterations to specifications quantities dimensions etc for production or other reasons subsequent to publication The information contained herein has been prepared by qualified experts within Munters While we believe the information is accurate and complete we make no warranty or representation for any particular purposes The information is offered in good faith and with the understanding that any use of the units or accessories in breach of the directions and warnings in this document is at the sole discretion and risk of the user HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 2 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters WARRANTY amp LIMITATION OF LIABILITY 1 MUNTERS warrants that the product shall be free of defects in materials or workmanship and will conform to the technical specification for a period of 1 one year from the date of initial installation on sight the warranty period 2 Load cells are not covered by MUNTERS s warranty 3 MUN
24. alarm message is on will direct you to the room with the alarm Resetting the alarm is possible but it only stops the siren and not the screen message Only by fixing the problem will the message stop Pressing the zero on the numeric pad while the alarm is activated will open the room status screen O K No com E Alarm E An empty square indicates that the Farm Center identifies the houses correctly K A filled square indicates an alarm is on E A dotted square indicates that there is no communication with the Farm Master Note gt Once communication is off there is no history accumulation in the Farm Center K A dotted lined square indicates N A not available HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 14 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication V Munters Farm Master amp Farm Center Hotkeys To reach the Hotkeys screens press the Hotkey number while viewing the main screen The room number is located on the upper right side of the Hot screen to view the status of deferent rooms first enter the desired room using the room key and pressing the room number Then press the desired screen Hotkey number Hot key 1 Main screen Hot key 2 Temperature screen The temperature hot screen shows important information regarding t
25. alarm will turn on when digital input is active HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 40 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center Alarm Reset ALARM RESET 01 P lt Note gt To reset the alarm press Enter and use the Round Arrows key Alarm Reset gt NO to change from NO to YES Version Use this window to check the controller s software version CONTROLLER Farm Master Farm Center Use the arrow keas to switch between controllers and press select to view the software version Read From Plug There are 2 types of data plugs regular and gold The gold data plug can store up to 8 different settings By naming each setting differently you can easily write read data from the plug to the controller and vice versa Read from Plug Gold data plug SELECT SETTING 1 Room No 1 Room No 2 NO lt YES Use the arrow keys to shift from NO to YES and lt NO SETTING press Enter to read from data plug DATA ON THE PLUG Name Room No 1 Ver 1 00r01 OK gt ENTER Abort MENU Before loading the setting you can view setting name and software version for this setting Press enter to load the data on the controller To cancel reading from this setting press MENU READING FROM PL
26. ate variable heaters Default 0 0 Band Temperature range in witch the variable heater operates in the power range between minimum and 100 For example the heater temperature is 26 C the temp diff is 1 and the temp band is 2 At 25 C the heater will operate at minimum power according to minimum heat At 24 C and down the heater will operate at 100 and between 26 C and 24 C there will be a power band between minimum and 100 Default 0 0 Minimum Heat Minimum heaters operation for safety measures This parameter refers to both var heat 1 and var heat 2 Default 30 Maximum Heat Maximum heaters operation for safety measures This parameter refers to both var heat 1 and var heat 2 Default 100 End Day Set the last growth day for the Variable Heaters operation Default O HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 38 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center v Munters 3 MANAGEMENT Animal Inventory ANIMAL INVENTORY 01 Add Mortality Animal Placed Animal Update This table provides an update for animal inventory Add Mortality insert mortality Animals Placed insert animals placed Animal Update update number of animals e in case the wrong figures are accidentally entered it is possible t
27. ation baud rate with the PC set the number of Farm Masters connected to the Farm Center Max 10 Make sure you define the Farm Masters numbers in a following order without skipping digits For example 1 2 3 4 If not set this way the Farm Center will not detect any Farm Masters After defining the number of Farm Master controllers the Farm Center begins a search to find the controllers defined LANGUAGE Select language TEMPERATURE UNIT Select between Celsius and Fahrenheit Select between Milibar IN W C Pascal CM W C PRESSURE MM W C TOTAL ROOMS Select between meter and imperial Controls the speed OTHER UNIT and rain flow Units for speed are meter h or mile h and for rain millimeter h or inch h TIME Set clock time PASSWORD Set password to protect data lt Note gt The last six parameters are general for all of the Farm Masters HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 19 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters 1 CONTROL Temp Curve TEMP CURVE 01 Day Target TT e The FARM MASTER provides separate temperature curves for growth day target temperature heat temperature tunnel temperature and low high alarm temperatures The controller creates a curve for
28. come Except for the above express warranty MUNTERS makes no other warranties express or implied relating to the products MUNTERS disclaims and excludes the implied warranties of merchantability and fitness for a particular purpose No person is authorized to make any other warranty or representation concerning the performance of the products other than as provided by MUNTERS Software Version 1 3 Document Version 2 1 Munters Italy S P A 39 0183 521364 S FAX 39 0183 521333 Italy HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 3 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center Support Information Table of Contents Explanation of Symbols and Manual Elements Introduction Components General Description Features Getting Started 5 Step Installation Guide Farm Center Keyboard Farm Center Main screen Hotkeys Farm Center Setup 1 CONTROL Temp Curve Min Max Level Humidity Static Pressure SystemParameters Control Mode 2 DEVICE Vent Levels Var Fan Levels Curtain Levels Circulation Fan Cool Pad Foggers Light Feed Extra System Time Clocks Variable Heat HC MIT UmGB 1557 05 09 Munters Europe AB 2009 Farm Master amp Farm Center User amp Installation manual for pigs Munters reserves the
29. each one and uses it as reference The program will alter at midnight prior to the next day on the next row programmed There are up to 10 programmable rows but the controller will maintain yesterday s settings for every empty line therefore it is not necessary to fill the entire table Limits Day 0 999 Target 0 40c Alarm low 0 40c without floating point Alarm high 0 40c without floating point Min Max Level Soft Minimum By Day Day Min Cold Min Warm 1 1 11 14 13 98 19 Soft Minimum By Time From Time Min Cold Min Warm 8 00 1 7 20 00 3 5 HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 20 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters From Time Min 8 00 1 20 00 The Minimum Maximum Level menu sets the current absolute minimum and maximum ventilation levels available You have 4 minimum maximum level choices D Min Max by Growth Day 2 Min Max by Time of Day 3 4 Soft Min Max by Day or Time The third option provides the following in extreme cold weather the min level ventilation might be decreased For that the user utilizes the Soft Min level that operates according to outside or inside temperature For example Target temperature 23 3 C Growth day 1 Min Max Levels Day
30. er amp Installation manual for pigs Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters 10 61 G Munters Farm Master amp Farm Center Getting Started 5 Step Installation Guide This is a quick 5 step guide that will help you figure out the order of actions for a proper system installation 1 Hardware Installation Read all technical specs and use the wiring diagrams from page 53 on this manual to properly install all hardware 2 Farm Master Cold Start Plug in the controller and hold its three keys simultaneously for a few seconds until a CLD sign will appear This action erases the memory completely and loads the default definitions 3 Farm Master Unit Number Press the two arrow keys together until the number sign no blinks Select the unit number with the up and down arrows and press Select 4 Farm Center Cold Start Plug in the controller and hold the delete key DEL for a few seconds until a Cold Start sign will appear This action erases the memory completely and loads the default definitions 5 Farm Center setup Room 0 Follow the instructions on page 18 lt Note gt Before making any changes make sure you are changing the correct room by checking the room number on the upper right side of the screen 6 Farm Center Installation Follow the instructions from page 48
31. er on tunnel exit enter a large positive number such as 90 0 Default 0 0 Exit Delay m delay time after satisfying tunnel exit conditions Default 5 minutes CURTAINS Calibration Steps to ensure accurate positioning of the curtains the controller may periodically calibrate the curtain position This parameter sets the maximum number of curtain movements or stages between calibrations Calibration consists of forcing the curtain to the nearest limit 0 or 100 with adequate overtime to ensure reaching the limit switch Then the curtain returns to its proper position In the event several curtains require calibration they calibrate one ata time to reduce the amount of restriction to normal ventilation The stage counter resets automatically each time the curtains reach a limit point to prevent excessive calibration Default 99 COOL PAD From Level from what ventilation level to begin cool pad operation O is no operation Default O Temp Band on off differential or Happy Zone with respect to temperature for the Cool and Cool Pad relays These normally control the water pump for the cool cells Default 1 0 Humidity Band on off differential or Happy Zone with respect to inside humidity for the Cool and Cool Pad relays Default 2 0 HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 27 61 Munters Europe AB 2009 Munters reserves the right to make alte
32. he operators can conveniently use the control and read indicators and displays 3 Give your installation a professional appearance with all wiring in conduit or neatly installed Keep low voltage wires separate from high voltage wires 4 Use shielded wiring for low level signals For buried wiring building to building runs use high grade jell filled cables that are impervious to moisture 5 Seal cable entry points and control boxes to prevent contamination and corrosion If you use silicon sealant with acetic acid cure keep the control open and ventilated until cured Otherwise the acetic acid will attack the metal parts including circuitry 6 Drill cable entry holes on the bottom of the box only HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters 55 61 Farm Master amp Farm Center G Munters Mechanical Installation Guide The Farm Master must be installed by an authorized electrician Power must be disconnected to avoid electrical shock and damage To avoid exposing the Farm Master to harmful gases or high humidity it Is recommended to install it in the service room Installation Category Over voltage Category Il The power supply to the controller should be protected by 10 Amps circuit brea
33. he status of temperature sensors attached to the Farm Center The average temperature defined in table 6 6 is displayed on the upper left side and shows the average of temperature sensors T1 through T3 Table 6 2 enables the user to set the temperature sensor T3 as OUT and therefore T3 presents the outside temperature On the right side you can see the temperature for entering tunnel ventilation mode T1 244 01 T2 2514 AVG T3 225 TUN poor Ne OUT Hot key 3 Targets Screen This screen shows all of the target TARGETS 01 levels selected for any of the TEMP 22 5 PRESS 0 01 controller s functions MIN LEVEL 5 ON 60 MAX LEVEL 15 OFF 240 Hot key 4 Curtain Position screen This screen shows the curtain opening position in percent If for example curtain 2 show 40 it is 40 open CURTAIN POSITION 01 CURT 1 50 CURT 2 CL CURT 3 40 CURT 4 TUNNEL OP INLET HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 15 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities ete for production or other reasons subsequent to publication Farm Master amp Farm Center Hot key 5 Curtain Steps CURTAIN STEPS CURT 1 12 CURT 2 CURT 3 14 CURT 3 TUNNEL INLET Hot key 6 System Status SYSTEM STATUS 01 HUMIDITY TREAT ON OFF CYCLE STATUS ON OFF CYCLE LEFT 29 Hot key 7 Variable Fans VARIABLE FANS
34. ker All electrical connections should comply with National Electrical code NEC 1 2 Open the enclosure lid by unfastening the four screws Using the provided bag of screws and plastic caps drill holes in the three designated areas inside the Farm Master Place caps on the screws once mounting is complete Drill holes at bottom of the box and place cable holders Place the required cables through the cable holders at the bottom of the unit Connect the wires according to the wiring diagrams Make sure that you use wires large enough for the load of the variable speed To connect temperature and humidity sensors use shielded two or four conductor 18 24 gauge cables Connect the shields to the Ground metal strip Do not connect the shields to more than one point or you may induce ground loop currents Close the Farm Master enclosure lid carefully and tightly Use RTV silicon or equivalent sealant to seal the cable holders After installation is completed operate the Farm Master for a few hours and re check for proper operation Environmental Protection Recycle raw materials instead of disposing as waste The controller accessories and packaging should be sorted for environmental friendly recycling The plastic components are labeled for categorized recycling HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 56 61 Munters Europe AB 2009 Munters reserves the right to
35. make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center Metal Sheet Assembly Diagram Screws Figure 1 Metal sheet assembly diagram Instructions 1 Drill holes in the three designated areas located in the back of the controller 2 Mount the controller using the 3 screws provided in the small plastic bag 3 Place the provided plastic caps on the screws HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 57 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Farm Center Farm Master Network Connection To P C com aen jil Farm Center HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 58 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Farm Master Wiring Diagram 1 Analog Output Power Potentiometer Relays Variable speed RHS 2 L e g 8 m 0 T H P ee b j b d F i q F vE i i E x l IIT ATT Da TITEFTYTETIITITIT j sk moa apana eT fom G B 1 padat
36. manual will help you get the most out of your new MUNTERS controller Please read the manual before installing and configuring your Farm Center Farm Master system Support Information Using this equipment for any other purpose or in a way not within the operating recommendations specified in this manual will void the warranty and may cause personal injury Explanation of Symbols and Manual Elements A caution Cautions alert you of potential damage to the controller caution if the procedures are not followed carefully _ TSK Dangers alert you of potentially hazardous situations A DANGER which if not avoided could result in death or personal injury C2 a x gr sS s r lt N ote gt Notes contain important tips and additional information you should know HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 7 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center Introduction This manual provides easy to use information for installation operation long short term planning and parts listing The table of contents is an outline of the relevant information in this manual Read this manual before operating your MUNTERS Controller If you have any questions or comments regarding your controller please contact
37. ns only HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs Munters Europe AB 2009 Munters reserves the right to make alterations to specification s quantities etc for production or other reasons subsequent to publication 53 61 Farm Master amp Farm Center V Munters Farm Master Installation Guide Sensors and Shielded Wiring 1 For long shielded wires connect the shield to ground at one end only 2 From the ground terminal run a heavy wire directly to the ground rod It is acceptable if necessary to run the heavy ground wire to the electrical service grounding system rather than directly to the ground rod 3 Do not use light wires for these ground connections They must carry heavy lightning currents sometimes exceeding thousands of amperes Certainly do not use the shielding of sensor and low voltage wiring for this purpose 4 Ensure that all ground connections go to a single local point When lightning strikes grounds a meter or two apart will be at significantly different voltages If you have several electronic boxes with individual grounds connect all these together to a single point If Possible preferably to the surge protector ground This should continue to the ground rod or the electrical service In particular avoid grounding any controls remotely through shield wiring 5 Do not use shields to create a path for lightning For long shield wires such as
38. o correct them by entering negative figures Day amp Group DAY amp GROUP Growth Day 2 New Group Yes no Group No 4 Day and group keeps monitor the growth of groups Growth Day Set the number of growth day This parameter can also help determine the animals age New Group To start a new group select YES under new group fragment and the controller will automatically increase group number by one and set growth day to 1 Warning When starting a new group history will be deleted Group No You can manually change the group number HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 39 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities ete for production or other reasons subsequent to publication lt Not G Munters Farm Master amp Farm Center Alarm setting Alarm Delay sec represents the number of seconds between failure detection and the alarm operation Alarm Delay gt 60 ALARM SETTING f the problem is solved before the delay time ends R acs ALARM an alarm will not be recorded in the history log Low Alarm Diff 18 0 SENSOR ALARM Hi Alarm Diff 18 0 HIGH TEMP Low High High and low temperature ranges beyond which alarm is activated Out Compensate 0 0 Emergency Temp 35 HIGH TEMP LOW TEMP Out Compensation This parameter is added to the Var Fan Stop NO
39. ost Comm lost communication W Overflow water over flow F Overflow feed over flow Sn 1 Fail Sensor 1 failure Sn 2 Fail Sn 3 Fail Sn 1 Def Err sensor definition error Sn 2Def Err Sn 3 Def Err Sn 1 Out Rng sensor out of range Sn 2 Out Rng Sn 3 Out Rng Sn Not Def sensor not defined Aux Alarm auxiliary alarm Press Fail Low S Press High S Press HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 45 61 Munters Europe AB 2009 Mu nters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Event EVENTS ROOM 1 Besides the menu event message there EVENT are three kinds of events Menu 11 1 Power up how many times the controller was turned on 2 Power EE Reset how many times the controller was reset Cold how many cold starts were performed Menu which menu number has been changed The events table is similar to the alarms table but without icons For example In the table above menu 11 means that there was a change of settings in CONTROL menu 1 Temp Curve table HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 46 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantitie
40. ot Keys purposes G Delete The Delete key erases typing mistakes HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 12 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Farm Center Main screen lt Note gt The main screen shows basic information regarding rooms controlled by the Farm Center depending on what equipment is plugged in Other parameters like static pressure PRESS outside temperature OUT level message and offset are also shown on the main screen when they are plugged in Parameters are shown according to priority There is a square in level line indicating tunnel level TEMP Current room temperature RH Current room humidity TRGT Target temperature RH T Target humidity Time LEVEL Current ventilation level HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 13 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center A caution In case of an alarm a blinking message will appear on any one of the main screens in addition to the siren Pressing 0 on the main screen when the
41. output HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 49 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication V Munters Farm Master amp Farm Center Variable Speed Fan VAR SPEED FAN 01 FUNCTION 1 VAR Fan 1 gt YES 2 VAR Fan2 YES To define a speed fan select yes This table will fill out according to the number of triacs in your system 0 2 Sensor Definition FUNCTION Select the temperature sensors 1 4 to use for Average each function using the Round Arrows key to Tunnel apply and remove check marks Heater 1 You will see only the devices defined in the Heater 2 relay layout and variable heat Heat Lamp 1 Heat Lamp 2 Curtain 1 lt Note gt Cool cell Average the average definition refers to the average temperature according to the sensor defined An empty line defined for a certain sensor indicates that the sensor will operate according to the average temperature definition Ex System 1 Tun Curt Var Heat 1 Curtain Setup CURTAIN SETUP 01 CURTAIN OPEN CLS Curtaini 60 DU Curtain Setup tells the controller how fast your curtains Curtain2 60 60 and side inlets move It needs this information to properly calculate automatic inlet advance as well as inlet and curtain positions Curtain3 60 60 Curtain4 60 60
42. product are not originally supplied by MUNTERS ii the defect is the result of an act of nature lighting strikes electrical power surge or interruption of electricity ili the defect is the result of accident misuse abuse alteration neglect improper or unauthorized maintenance or repair MUNTERS warns and alerts all users that the Product is inherently complex and may not be completely free of errors MUNTERS s products are designed and manufactured to provide reliable operation Strict tests and quality control procedures are applied to every product However the possibility that something may fail beyond our control exists Since these products are designed to operate climate control and other systems in confined livestock environments where failure may cause severe damage the user should provide adequate backup and alarm systems These are to operate critical systems even in case of a MUNTERS system failure Neglecting to provide such a backup will be regarded as the users willingness to accept the risk of loss injury and financial damage In no event will MUNTERS be liable to a user or any third party for any direct indirect special consequential or incidental damages including but not limited to any damage or injury to business earnings lost profits or goodwill personal injury costs of delay any failure of delivery costs of lost or damaged data or documentation lost or damaged products or goods lost sales lost orders lost in
43. r production or other reasons subsequent to publication Farm Master amp Farm Center oystemParameters TEMP Offset Use this parameter to change the offset target temperature up or down for any purpose Default 0 0 Band this refers to the target temperature zone Cool Factor 10 Cold Above TRG 3 0 Cold Below TRG 1 0 range The Users Manual refers to this as the Happy HEATER Zone Heat Band 1 0 Default 1 0 Heat Lamp Diff 0 0 Cool Factor the minimum correction towards dram ssi ae a target happy zone during each increase ventilations 3 delay patience factor If the temperature does not Cue NO Level Control Day improve by this amount the controller will increase one level Default 10 Soft Min Temp OUT Soft Temp Band 10 0 PRESSURE Cold Above TRG Temp Change To Be Considered Press Control NO As Quick Drop In Degrees To Reduce A Level To T T Reach Above Target Temp Degrees Inc Delay s 180 Default 3 0 3 Dec Delay s 120 Cold Below TRG Temp Change To Be Considered TUNNEL As Quick Drop In Degrees To Reduce A Level To 45t Tun Level 0 Reach Below Target Temp Degrees Dif Below Exit 2 0 Default 1 0 T Out Dif Exit 18 0 HEATER Exit Delay m 5 E CURTAINS Heat Band Set the happy zone for the heaters on off Calib Steps 99 Default 1 0 3 COOL PAD Heat Lamp Diff differential from target temperature to From Level 0
44. rations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters FOGGER From Level from what ventilation level to begin fogger operation O is no operation Default O Temp Band See cool pad above Default 1 0 Humidity Band See cool pad above Default 2 0 VAR FAN Freeze Protect A general protection for the variable speed fan motor When the variable speed fan starts from zero speed the freeze protection activates it to 100 for 5 seconds Default No Min Motor1 2 3 4 Spd Safety speed fan operation delay This is the Fan minimum speed to begin operation Default 30 Control Mode CONTROL MODE 01 Set Mode gt Normal Empty In this screen control mode can be set choosing between Normal mode and Empty mode EMPTY MODE Empty mode is applied in cases of empty houses When Empty mode is selected All alarms will be disabled A flashing massage will appear while displaying temperature E In Farm Master and Empty House in Farm Center setting controller to Normal or Empty mode will insert an event to History Event table HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 28 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center
45. rations to specifications quantities etc for production or other reasons subsequent to publication G Munters 30 61 Farm Master amp Farm Center Vv Munters Var Fan Levels The percentage for a full circle represents the fan operation percentage form the maximum If set on 30 it will operate up to 30 of the maximum The percentage for a half full circle represents the fan operation percentage in off mode during cycle operation The fan will operate at 100 at on time If set on 20 the fan will operate at 20 of the full power during off time in the cycle and will increase to 100 at on time HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 31 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities ete for production or other reasons subsequent to publication Farm Master amp Farm Center Mv Munters Curtain Levels CURTAIN 01 01 U U U Curtain Level Example Curtain E T set the curtain levels to correspond with the ventilation levels Some producers will want to open the tunnel curtain somewhat Levels prior to the actual tunnel This is 1 thru convenient to control pressure in retrofit 7 houses which may not have sufficient side inlets for the number of fans required 0101 0 0 U in side ventilation a waka ae 1 Peep 4 You can also optionally run the tunnel curtain under pressure control
46. rnates between the name of the I O and an ON OFF sign Pressing the arrow keys allows switching between on and off rL 1 7 Relays 1 to 7 SPd Variable speed Check minimum to full capacity using the arrow keys AQ1 4 Analog outputs 1 to 4 t1 t2 Temperature sensors with the A D counts blinking on the screen Hu humidity sensor A D counts Ai1 2 Analog inputs 1 to 2 Prs Pressure A D counts DG1 3 Digital inputs 1 to 3 HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 52 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center Technical Specifications Power supply Mains voltage _ single phase Main fuse secondary fuse Maximum power consumption G Munters 115 230VAC 315 mA 1A 10VA Available power for peripheral equipment Analog Inputs 3 temperature sensors 5 analog outputs 20MA 1 humidity sensor input 2 analog inputs Digital inputs 3 digital inputs dry contact Relays outputs 8 N O power relays 2HP Housing Dimensions LxWxH Ambient climate Operating temperature range Storage temperature range Indoor Applications RTS 2 THERMISTOR 0 10V 0 3V Q 5V 5V 2mAmp 30Amps 200Vac 92 5x 3x36 0 C to 50 C 10 C to 70 The equipment is designed for use in Indoor Applicatio
47. s etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters 5 CALIBRATION Temperature TEMP CALIB 01 Temp 1 Factor 0 0 Temp 2 Factor 0 0 Temp 3 Factor 0 0 Temp 4 Factor n a e The temperature sensor is a very accurate sensor with a deviation of 0 1 If needed calibrate the temperature sensor by using a very accurate reference instrument and enter the offset number for each sensor in the Temp factor line Use the up and down arrow keys to select sensors Humidity HUM CALIB 01 Humid factor 0 0 If needed calibrate the humidity sensor by using a very accurate reference instrument and enter the offset number in the Humidity factor line Pressure PRESS CALIB 01 Value A D Press ENTER to calib Water amp Feed Water feed 01 Water per pulse 0 1 Feed per pulse 1 0 The water and feed system operates on a pulse counting method Enter the amount of feed water per pulse HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 47 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center v Munters 6 INSTALLATION Relay Layout RELAY LAYOUT 01 FUNCTION Heater 1 02 Heater 2 Each relay can be defined to any of the functions on the following list e
48. s Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center Calibration Temperature sensors are very accurate and most likely will not require calibration However if calibration is required it will be done in the following way Temperature sensor calibration gt Use an accurate thermometer reference gt Place it near the temperature sensor gt Make sure that the inside temperature is stable gt Calibrate the temperature sensor immediately after reading Calibration procedure 1 In order to get to the calibration menu press select and the up arrow keys simultaneously and hold them together for about two seconds 2 The display alternates between the sensor number and the temperature measured 3 Use the arrow key to change the temperature 4 Press select to move through the sensors and the arrows to change temperatures NOTE Calibration of humidity sensor is done exactly the same way the only difference is that instead of measuring temperature the humidity is measured by an external humidity sensor Test The test option is used mostly in the installation process and it enables the installer to check systems In order to get to test menu press select and down arrow keys simultaneously and hold them together for about two seconds The display alte
49. s a curve between min warm and min cold while decreasing levels When temperature increases the level remains at the lowest level reached until reaching the heat temperature When using Soft Min according to outside temperature there is a curve between min warm and min cold while decreasing and increasing levels To select the type of minimum maximum go to system parameters and change the level control see page 21 Humidity HUMIDITY 01 Target Delay minute 0 0 Duration sec 0 2 Band Below Heat NO Target Set the humidity target for Delay delay time before humidity treatment The controller checks during the delay time whether the humidity is above the target Duration humidity treatment duration time Band band zone to balance the treatment Below heat select if you wish to initiate humidity treatment below heater temperature HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 23 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication Farm Master amp Farm Center V Munters Static Pressure Out Temp low Set outside low temperature STATIC PRESSURE 01 definition for low pressure target Out temp low Press Low T Static pressure target for the Press low t outside low temperature See graph below Out temp high point 1
50. s organization in Sweden Munters Europe AB Phone 46 0 8 626 63 00 Fax 46 0 8 754 56 66 Finland Munters Oy Phone 358 0 9 83 86 0330 Fax 358 0 9 83 86 0336 France Munters France S A Phone 33 0 1 34 11 57 50 Fax 33 0 1 34 11 57 51 Germany Munters Euroform GmbH Phone 49 0 241 89 000 Fax 49 0 241 89 005 189 Italy Munters Euroemme S p A Phone 39 0183 52 11 Fax 39 0183 521 333 Kingdom of Saudi Arabia and Middle East Hawa Munters c o Hawa United Cooling Syst Co Ltd Phone 966 0 1 477 15 14 Fax 966 0 1 476 09 36 Norway via sales organization in Sweden Munters Europe AB Phone 46 0 8 626 63 00 Fax 46 0 8 754 56 66 South Africa amp Sub Sahara Countries Munters Pty Ltd Phone 27 0 11 971 9700 Fax 27 0 11 971 9701 Spain Munters Spain S A Phone 34 91 640 09 02 Fax 34 91 640 11 32 Sweden Munters Europe AB Phone 46 0 8 626 63 00 Fax 46 0 8 754 56 66 Switzerland via sales organization in Germany Munters Euroform GmbH Phone 49 0 241 89 000 Fax 49 0 241 89 005 189 United Kingdom Munters Ltd Phone 44 0 845 644 3980 Fax 44 0 845 644 3981 Export amp Other countries Munters Europe AB Phone 46 0 8 626 63 00 Fax 46 0 8 754 56 66 Region Americas Munters Corporation Phone 1 0 978 241 1100 Fax 1 0 978 241 1219 Region Asia Munters K K Phone 81 0 3 5970 0021 Fax 81 0 3 5970 3197 Euroemme is a registered trademark of Munters AB
51. te cooling When temperature raises diff above target cooling process will begin When temperature reduces back to target cooling process will stop RH As long as the humidity Band are below this level the cooling operates Cooling stops only at humidity level band See figure below ON OFF sec On Off cycle by seconds Band The cooling table has its own happy zone for temperature and humidity that can be set at the system parameters under cooling section The cooling system turns on the amount above specified in the column Diff and turns off when the temperature drops the amount specified in the band Peer cc cc RRR RRR RRR RRR RRR RRR ERER RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR EOE RRR SEES E SEES RRR RER RRR RRR RRR REER RRR REER RRR RRR RRR RRR RRR RRR SHFHHEEOESHOSESESESELOLESELESESEHELELESESEESEEES ESSE OSES ESOSESELOSOEESOSOE ESSE OSES ESE ESSE OSES E SEES H OLEH ESET EE EEE HET OS ETE OE EOE rE ro O EOE ee seT rere reseserosereN essssesososesososesososesososesososesososesososesossoesoosoeooosososososesosososososoesososesososesososesososesososesososesosososossoesososesossoeosssossoosososososes RRR RRR RRR RRR RRR RRR RRR RRR RRR RER RRR ERRER RER RRR RER RRR SERR RRR RRR ERRER RER RRR RRR RER RRR RRR RRR RRR RRR RRR RRR ERRER RRR RER RRR RER RRR RER RRR RER RRR RER RRR ERRER SERRE RRR RRR HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs
52. will control the circulation fans 3 if more then one sensor is defined for the circulation fans when the difference increase between any 2 sensors the circulation fans will begin operation From Time from what time to start the application To Time to what time operate this application From Level from what level to operate this application To Level up to what level operate this application If any of the 4 definitions above is set on 0 the circulation fan will operate at any time or level according to the differential HC MIT UmGB 1557 05 09 Farm Master amp Farm Center User amp Installation manual for pigs 33 61 Munters Europe AB 2009 Munters reserves the right to make alterations to specifications quantities etc for production or other reasons subsequent to publication G Munters Farm Master amp Farm Center Cool Pad The cooling table provides settings for the evaporative cool pad system There are up to 5 fragments allowing precise control over this system Several fragments can be selected for the same day Cool Pad 01 From TIo 08 00 20 00 30 85 30 90 E 10 00 18 00 50 75 60 60 ome ewe m m wwe eww m m m m we we m wwe m ewww ween ow www wm www ow we www mm mew we ee m m meme ewe ee ewww wen ewe ew ew wm www ew ew ww www ww ww ew ew wwe m m m m m ow ew m ew ew m g FROM HH MM Start time TO HH MM End time DIFF Differentiation from target temperature to activa

Farm-Center

Contents

Download Pdf Manuals

Related Search

Related Contents