Chapter 4 Using the DW5065
Contents
1. installed correctly and is powered off when connecting the DW5065 wall panel Connect the DW5065 wall panel to the Matrix system with a twisted pair CAT6 cabling with a maximum cable length of 300 meters Make sure the DW5065 is connected to one of the PI ports on the rear side of the digital audio matrix Only PI 1 8 can handle audio inputs Go to the setup menu in the web based interface of the digital audio matrix and go to System configuration Click on DW5065 for creating the desired settings for the DW5065 wall panel An unigue address should be selected for every connected wall panel The address for a wall panel i AUDAC always starts with the letter W When only one wall panel is connected the most logical way is to start with address W001 and increase the address number for every additional wall panel W002 for wall panel 2 W003 for wall panel 3 After the desired address is selected click the Set Address button A message will start blinking on all the DW5065 wall panels connected in your system When the function selection dial on the wall panel is pressed the selected address will be assigned to the corresponding wall panel Now the zones which should be controlled by means of the wall panels and the selectable inputs need to be selected This can be done in the user interface with the two dropdown lists When the zone or input is selected it automatically appears inside the listbox To re2. provide 15V phantom power to this microphone input Software selectable AUDAC 7 8 2 5 Graphic color LCD display This graphical color LCD displays gives a clear overview of all the functions and settings of the wall panel Rotatable function selection dial The big rotatable dial enables you to control all functions and settings of the wall panel by just three simple actions Rotate left Rotate right and Push Actions such as browsing between the zones increasing the volume selection of the audio source can be done by rotating the dial left and right Actions such as confirming cancelling toggling between settings proceeding and returning to the previous window can be done by pushing the button AUDAC Overview rear panel The rear panel ofthe DW5065 contains an 8 pin connector for connecting the wall panel to the matrix system and a jumper which is meant for terminating the RS485 databus A detailed description of how the DW5065 should be connected can be found in the chapter Connecting the DW5065 The jumper for terminating the databus should always be placed when only one wall panel is connected to the databus and is always provided and placed by delivery 8 pin Euro Terminal Block connector Chapter 2 Quick start guide This chapter guides you through the setup process for a basic project where a DW5065 wall panel should be connected to a digital audio matrix Make sure the digital audio matrix is
3. set to the desired level press the dial again for scrolli the input source by ng between the settings You can select rotating the dial till Input illuminates Volume Input Mute Bass Treble Back Volume Input Mute Bass Treble Back Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Input 7 When Input is lit you can push this button and you will be redirected to the input selection window This window shows all configured input channels which can be selected The displayed input names correspond with the input names which are configured in the matrix settings You can scroll through the inputs by rotating the selection dial and you can select the desired input by pushing the dial When the input selection is made you can scroll further through the settings menu and make other changes such as muting and changing the tone control When the zone should be muted just scroll to the Mute button and push the selection dial When the selection dial is pushed there will be toggled between Mute and Unmute 21 22 Volume Input Mute Bass Treble Back Volume Input Mute Bass Treble Back The latest settings which can be changed to the zones are the wo band tone control The tone control can be activated by selecting the Bass and Treble buttons and the adjustment of the tone control works with a fader just as the volume control You can increase and decrease the h
4. such as Volume change Input change Mute change Tone control change and set tings change can be blocked by checking the checkboxes AUDAC 17 5 The microphone input has the possibility to provide 15V phantom power for powering condenser microphones The pantom power can be switched ON and OFF by clicking the Enable Mic Phantom checkbox This setting can also be changed in the DW5065 settings menu If Block settings menu is not checked 6 The Backlight level screensaver and screensaver delay can be set by means of three dropdown boxes This setting can also be changed in the DW5065 settings menu If Block settings menu is not checked 7 When the settings are made press the Save to Wallpanel button and the settings will be send to the selected DW5065 wall panel Previously made settings can be retrieved from the wall panel by clicking the Load from Wallpanel button Hereby the settings which are stored in the wall panel will be displayed in this window making it possible to make any changes to the current settings 18 AUDAC Chapter 4 Using the DW5065 When the DW5065 is correctly installed connected and configured the wall panel is ready for opera tion The standard screen of the DW5065 will give an overview of all zones which are configured to be controlled by means of the DW5065 wall panel The zone names displayed on this screen correspond with the zone settings which are set in the user interfa
5. DW5065 User Manual amp Installation Guide DigitaPAll In One Wall Panel www audac eu Index Introduction Chapter 1 Overview of DW5065 Overview front panel Front panel description Overview rear panel Rear panel description Chapter 2 Quick start guide Chapter 3 Installing Connecting amp Configuring Installing Connecting Configuring Chapter 4 Using the DW5065 Chapter 5 Technical Specifications Chapter 6 Notes AUDAC Introduction Digital All In One Wall Panel The DW5065 is an All in one wall panel designed to work in combination with AUDAC digital matrix systems This wall panel has a graphic display and can control the routing volume bass treble and mute for multiple zones up to 8 on one R2 Besides those control functions it also provides the possibility to connect a microphone and a stereo line input source The DW5065 wall panel should be connected with UTP FTP Cat6 or better cable The following functions of multiple zones can be controlled Volume within a range of OdB to 70 dB All input sources can be selected Mute can be activated Bass within a range from 9dB to 9dB Treble within a range from 9dB to 9dB The microphone input on the wall panel is connected with a female XLR connector while the line inputs are performed using RCA connectors AUDAC 5 Chapter 1 Overview front panel The front panel of the DW5065 wall panel contains a 2 5 Graphic col
6. ce of the matrix The main screen provides an overview of the zone names You can scroll to the desired zone by rotating the selec tion dial The zone names will illuminate one by one when rotating the dial When the desired zone is selected you Zone 4 can proceed to the zone settings by pushing the selection Zone 5 dial The screen has the possibility to display up to five zone names settings when more than 5 zones are configured you can scroll further down The latest option is always the Settings button Click this button when you want to make any changes to the wall panel KU DAC 19 Zone Zone 2 Zone 3 Settings 20 30dB Volume Input Mute Bass Treble Back Volume Input Mute Bass Treble Back When the desired z one is selected you will proceed to the settings menu for the corresponding zone Settings such as Volume control control can be mad nput signal selection Mute and Tone e for the corresponding zone On the left side of the display are all the possible settings displayed and scrolling betwe en the settings can be done by rotating the selection dial The settings will illuminate one by one when rotating the d ial When the desired setting is selected you can change it by pushing the dial For example when Volume is selected the attenuation on top of the fader will illuminate and the volume can be changed by rotating the dial When the volume is
7. igh and low tones the same way as adjusting the volume by simply rotating the selection dial The Bass and Treble both can be adjusted between the ranges of 9dB and 9dB The latest selection button is the Back button By clicking this button you will return to the main screen where zone selection can be made Zone 1 When returning back to the main menu the latest selectable option is Settings By selecting this option changes to the settings of the wall panel can be made After clicking this button you will be redirected to the settings menu The Zone 4 settings menu shows different options like Mic Phantom Zone 5 Backlight Screensaver and Info Zone 2 Zone 3 Settings Mic Phantom With the Mic Phantom option the 15V DC phantom power Backlight to the microphone input on the wall panel can be enabled Phantom and disabled while the Backlight option enables you to Screensaver adjust the backlight intensity for the LCD display With the Info ON Screensaver option the desired screensaver and the time Back before the sceensaver shows up can be set Info shows some more information about the wallpanel and the current software version AUDAC 233 Chapter 5 Technical Specifications Line input Stereo RCA input Sensitivity 8dB 6dB Signal Noise gt 95 dB THD N lt 0 02 Microphone input Balanced XLR input Sensitivity 14dB 50dB Signal Noi
8. ilities A wall panel with additional audio input can be connected to every PI port supporting digital audio transfer PI1 to PI8 Multiple wall panels can be connected to one PI port when only one wall panel on every port supports additional audio channels Up to 8 additional digital audio inputs can be con nected to one matrix system Connections which WORK Connections which DON T WORK 050 Multiple wall panels with audio input on one PI port Multiple wall panels with audio input on multiple PI ports AU DA C 1 5 Configuring Before the DW5065 can be operational the configurations should be made First of all an address needs to be assigned and the available inputs need to be defined Follow these steps to configure 1 Go to the Setup menu and click System configuration Now you have the possibility to choose between Paging DW5065 and DW3018 4018 To configure the settings for the DW5065 wallpanels click on the corresponding button Now a window is displayed which provides all the configuration possibilities for the DW5065 On the left side a dropdown list is displayed whereby the address for the DW5065 can be selected The address can be selected between W001 and W008 Logically you start with address W001 for the first wall panel and increases for every additional wall panel After the desired address is selected click
9. move a zone or input from the listbox select the desired zone or input in the listbox and click the Remove Zone or Remove Input button Next to the listboxes are several selection 8 checkboxes shown whereby some presets restrictions can be made to the corresponding wall panel After the settings are made click the Save to Wallpanel button on the bottom of the window and your changes will be uploaded to the wall panel Your wallpanel is now ready for operation AUDAC Chapter 3 Installing Connecting amp Gonfiguring Installing For installing the DW5065 two different kinds of flush mount installation boxes are available The plastic installation box WB5065 FG is meant to be used for installation into gypsum wooden or other kinds of plate walls with a thickness between 7 mm and 25 mm An installation hole with dimensions 135 x 75 mm should be cut wherein the installation box should be placed When the wall panel is placed into the installation box and the screws are tightened the wall panel will be secured to the wall The second type of installation box is a steel version WB5065 FS which can be used for mortar in brick or stone walls Make sure the installation box is installed upright notice the text and the sticker on the installation box 2 AUDAC Connecting The DW5065 wall panels should be connected to the PI Peripheral Interface ports on the rear side of the matrix system with an UTP CAT6 twi
10. or LCD display with an unbalanced line input connected by RCA connectors and a balanced microphone input connected by an XLR connector Each input is accomodated with a push lock gain control potentiometer and a Clip indicator LED A big rotatable function selection push dial is provided below the LCD display Unbalanced line input Push lock gain NV control potentiometer f with clipping LED 2 5 Graphic color Lo LCD display Balanced microphone j input Rotatable function selection dial Front panel description Unbalanced line input An unbalanced stereo audio source can be connected to these RCA connectors creating an additional local input Push Lock gain control potentiometer with clipping LED The sensitivity for the line and microphone inputs can be adjusted with these potentiometers Through the push lock mechanism they can be opened and hidden again by pressing them Above every potentiometer is a clipping indicator LED provided which illuminates when clipping of the input signal occurs When this LED is lit the signal is distorted and the level should be reduced by turning back the potentiometer The sensitivity for the line and microphone input can be adjusted between the ranges of OdB and codB Balanced microphone input A balanced microphone can be connected to this XLR input connector which allows to announce messages from a specific zone For powering condenser microphones there s the possibility to
11. se gt 75 dB THD N lt 0 05 Phantom power 15V DC Display 2 5 LCD 65k colours Connector 8 pin Euro Terminal block Dimensions 153 x 94 x 55 mm Built in Depth 37 mm Weight 0 2 Kg Installation standard BS4662 2 gang AUDAC gt Chapter 6 Notes 25 AUDAC AUDAC 27 2 AUDAC
12. sted pair cable 10 PI ports are available PI1 to PI10 where 8 of them support addidional digital audio inputs PH to PI8 So make sure the DW5065 wall panels are connected to PI ports ranging from 1 to 8 The two left PI ports PI9 and PI10 can only be used for connecting digital control devices and do not support digital audio transfer The maximum cable length between the matrix system and the wall panel may not exceed 300 meters MATRIX PI Port PINOUT RS485 Digital Audio 24V DC Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 RAM Pin 8 Male PIN 1 White Orange Orange White Green Blue White Blue Green White Brown Brown AUDIO TX A AUDIO TX B 24V DC RS485 A RS485 B GND AUDIO RX A AUDIO RX B AUDAC 33 ATTENTION The twisted pair cabling must always be straight In case of self made cabling it must be wired as described in this chapter to make the system work properly The twisted pair cable should be connected to the 8 pin Euro Terminal block connector on the rear side of the wall panel The connector starts with Pin1 on the left side to Pin8 on the right side These Pin s should be connected to the corresponding Pin s of the RJ45 connector TTT DW5056 Gonnector PINOUT Pint White Orange AUDIO RX A Pin2 Orange AUDIO RXB Pin3 White Green 24V DC Pin4 Blue RS485 A Pin5 White Blue RS485 B Pin6 Green GND Pin _White Brown AUDIO TXA Pin8 Brown AUDIO TX B 14 AUDAC Connection possib
13. the Set address button After this button is pressed the DW5065 will start blinking To confirm the selected address with the wall panel click the big rotary button on the front of the wall panel When this button is pressed the address will be assigned to the selected wall panel ic AUDAC 2 The zones which you want to control with the selected wall panel can be selected by means of the Controlled zones dropdown list When selecting a zone in this dropdown list the zone name will appear in the listbox below The zones can be removed again from this listbox by selecting them and clicking the Remove Zone button 3 The inputs which are selectable with the selected wall panel can be selected by means of the Selectable inputs dropdown list All inputs which available on the R2 can be selected in this drop down list such as the direct line inputs the peripheral inputs the fiber inputs the priority inputs and the integrated DSP signals When selecting an input signal in this list the signal name will appear in listbox below The input signals can be removed again from this listbox by selecting them and click ing the Remove Input button A maximum of 24 signal inputs can be selected The inputs which are selected in this listbox are available for all zones which can be controlled by this DW5065 wall panel Those inputs are not linked with the guick menu like the inputs on the DW3018 4018 are 4 Certain actions
Download Pdf Manuals
Related Search