Home

User Manual I. View Excavator

1. e The ticket can be also printed immediately from the main operating screen by keeping pressed da HEADER 1 19 95 2009 17 13 Ticket N HEADER 2 Bucket N A Total 3 27 ton 000282 IVWESC uso EN 00 TRI Header 1 Date amp Hour N ticket Header 2 Code and Name of the selected material Code and Name of the selected customer Code and Name of the selected truck Code and Name of the selected project Code and Name of the selected operator Bucket number bucket performed to load the truck Total load load in the truck 161 5 Weighing System User Manual I View Excavator English 5 11 2 Options It s possible to customize the printer ticket in the Options menu PRINT TICKET OPTIONS Total truck gt Copies Nr Same Number ON End of the day Ia Material ON Ticket N Client ON Header 1 Operator ON Header 2 Trucks ON Projects ON Show Totals Bucket N OFF Ticket N OFF Signature OFF Delete after the printing Copies Nr Number of copies printed automatically Same Number ON Keep the same ticket number for all the copies printed automatically Print Material Client Operator Trucks Projects Bucket N Ticket N Signature Ticket optional information ON Optional information included in the ticket Delete after the printing ON for zeroing the actual truck load automatically after the printing e Press WW t
2. e Short press Tag the weighing replaces the z button e Long press the following page will appear Booking switch kept pressed Cer print and delete truck A ex1t without ag changes gt Press again the booking switch or the a button to print the actual load truck and automatically delete the on screen values 9 gt Press to exit without changes 000282 IVWESC uso EN 00 TRI 47 5 Weighing System User Manual I View Excavator English 5 2 2 Weighing Angle Setting It s possible to select at witch angle of the first boom the system will start to weigh This setting can be changed at any moment to best fit the working condition 9 e From the main operating screen press to access the START WEIGH page START WEIGH Angle Actual Min VEDE Start First boom Angle used as start weigh trigger e Use f keys to manually change the actual start weigh angle W to use the actual boom angle as start weigh angle Actual Actual angle of the first boom Min Max Weighing Range Min and max angles first boom that can used as start weigh 000282 IVWESC uso EN 00 TRI 48 5 Weighing System User Manual I View Excavator English 5 3 TARE SETTING To keep the system accurate it s necessary to perform a new tare acquisition in particular work conditions The machine is cold first movements of the day Repeat the check when the oil temperature is stable
3. User Manual View Excavator aaaana ua d K e re H E H i j L d J Codice Manuale Manual Code 000282 IVWESC uso EN 00 TRI User Manual I View Excavator English Index Chapters Index UNN 2 INdex REVISION NOLES urina 5 1 EEN EA aaa 6 2 ld le Sct uss A E E E EA EAE E E EA A N EE 7 3 A Tea AG EEE 9 CAN VZzeae ee a ee 9 PN H 4 ee SE EEE EE 11 4 1 MAINOPERATING SCHEEN ce cecscsessssssscscsssesssssssesssesecessssesssesesssesesesesassssseseesesesesesacaseseseeeusnsnsees 11 EN 13 AED Te gt EE 14 EEE GO RR 15 4 2 1 Height Reference Zeroing ENEE 15 4 2 2 Depth Offset Sete 16 43 REACHFUNG TION EE cast sestissteucicustanedenstucsisestoxwdvesboesseuse 17 SEENEN 17 432 Reach TN 18 od PER RN Nr 19 4 4 4 Laser Setting E 19 4 4 2 LASEPDEAMAGGUIMNG 20 do SEOPEFUNGIION E 21 4 5 1 Set leide e 21 000282 IVWESC uso EN 00 TRI 2 Index Chapters User Manual I View Excavator English E E E dn ME 22 4 5 3 XAxleslope settings 23 4 5 4 How to dig a sloped eartace eee eecsscesstssssssscscscsesesesesssesececscscsssesesesesesesaessssseseeeseesetstssseeeeeess 24 4 0 PROFILEFUNGCION EE 25 4 6 1 Set Profile function E 26 4 6 2 Use GE 27 4 05 EE Ebene 21 TEEN 28 4 6 5 Graphical Summary eesororsvsrrrerererenrsrsrersrerererenenrsrsnsrsnerenenenenrsrsnsnenenenenesrsrsnsnsnenenenenenssrsnsnnnenennn 30 4 6 6 Work witha profile 31 4l EFN In 32 Ao BS NTN 33 Lol TE v
4. moving the excavator on its tracks to dig to the same level at a different location on the site mo MMMM TT um NONNE I I ni Wii Uu UNE il W Memory Reference Icons e Set Reference a Keep Reference Work with the memory function gt Position the bucket tip on a reference point Choose anything stable that can also be accessed from the next location After moving the excavator you will need to use this same reference point or another point that is at exactly the same elevation gt Press S j the Set Reference will start to flash gt Press to store this point The reference icon off gt Move the excavator to your next position and place your excavator bucket tip on that same reference point used in the previous step gt Press y again to flash the Keep Reference gt Press to acquire the value The reference icon off It s now possible to continue to work Same reference Second location point accessed from both digging sites First location 000282 IVWESC uso EN 00 TRI 32 4 Digging System User Manual I View Excavator English 4 8 LIMITS FUNCTION Limits Icons e No Limits Min Depth set v Max Height set ty 8 v Min Max Limits set engen These functions are only an indication and don t affect the machine movements at all Note also that pivots and bucket blade where indication are referred are not really
5. Press again to select the desired mode and confirm with Low Speed gt Press The icon will continue to flash and the CompL message will appear gt Cross the laser beam rising the laser receiver at the minimum allowed speed speed indicator has to be in the lower part of the bar but not completely down attached to the border too slow and not acquired in this case gt When the laser is acquired the OK message appears gt Move down the laser receiver below the laser beam and the REF U message will appear gt Move the bucket to the reference point and press F 000282 IVWESC uso EN 00 TRI 84 6 Calibration Mode User Manual I View Excavator English High Speed gt Press The icon will continue to flash and the CompH message will appear gt Cross the laser beam rising the laser receiver at the maximum allowed speed speed indicator has to be in the higher part of the bar but not completely up attached to the border too fast and not acquired in this case gt When the laser is acquired appears the OK message gt Move down the laser receiver below the laser beam and the REF U message will appear gt Move the bucket to the reference point and press ME 000282 IVWESC uso EN 00 TRI 85 6 Calibration Mode User Manual I View Excavator English 6 3 WEIGHING CORRECTION If the system weighs always heavier or lighter than the real load weighed c
6. The bucket has been changed smaller bigger Some material stays in the bucket not possible to unload it The hydraulic circuit oil has been changed e From the main operating screen press to access the SET TARE page SET TARE Tare Actual Set Tare BucketLoad Load of the last weigh CC save last bucket as the tare AA exit without ey changes Tare Setting e Inthe SET TARE page select the Tare function and press wes to enter the setting B Ka gt Use es 2 to settare and to confirm Tare Zeroing e Perform an empty bucket weigh e Inthe SET TARE page select the BucketLoad function e Press Se to update the tare value with the last bucket load Tare Deletion e Enter the SET TARE page gt Press to delete the set tare gt Press to go back to the operating screen 000282 IVWESC uso EN 00 TRI 49 5 Weighing System User Manual I View Excavator English 5 4 PARTIAL TOTAL DELETION I e From the main operating screen press to access the Delete Menu DELETE DELETE Partial bucket Partial bucket Partial x 2 Partial x 2 Total truck Total truck Materials Total J Materials Total Enter confirm Home exit E z Partial bucket To be used if the bucket has been wrong or accidentally weighed and the material will not be putted on the truck gt Press Ne to delete the last bucket weighed LE Ga T
7. If six digits are few it s possible to set more digits through a parameter that allows the use of nine digits this is the limit Then if the Fixed UM is disenabled OFF there are limits while if the Fixed UM is enabled ON there are another limits refer to the Calibration Manual The limits of values with nine digits and Fixed Unit OFF are the following Totalload Partiallo ad Bucket n Target Load Display Totals max value x each material shown I 90700000 90700000 1 999 1 90700000 90700000 199956313 199956313 1 999 1 199956313 90700000 999 99 999 99 1 999 0 01 999 99 90700000 mit 999990 999990 1 999 1 999990 90700000 99977 70 99977 70 1 999 0 01 99977 70 90700 00 nad 89266 03 89266 03 1 999 0 01 89266 03 89266 03 000282 IVWESC uso EN 00 TRI 73 5 Weighing System User Manual I View Excavator English 6 Calibration Mode WARNING this setting affects the system accuracy Proceed only after the reading of the following instructions 6 1 BUCKET Note Take care to have all the needed tools to calibrate the bucket or call a qualified installer Adjust an existing bucket or calibrate a new one gt From the working page press WA to enable the bucket selection The bucket icon flashes Bucket L Bucket Calibration Menu DogBone Setting Bucket d Bucket Setting None Grab No sensor or Grab Setting J e Use or to select the setting to perform and confirm 0 key 000282 IVWESC
8. Load J to perform the weighing With Auto Book function active it s not needed to press the button every time that it s necessary to weigh because the weighing system it s always ready and this button will work as enable or disable switch of the weighing system 2 Follow the on screen instruction If the boom is above the start weigh point will be necessary to move down the boom 3 When the boom will be in the correct position Ready to weigh with the indication move up its possible to perform the weighing rising up the boom 4 Overtaken the start weigh point there will be the on screen Weighing indication and the control box buzzer will be ON If the weighing is correct the load in the bucket will be shown on the partial weight and the value will be also added to the total In a negative or 0 load in the bucket will be computed the value will be not added to the total lf an error happens during the weighing phase there will be the relative message on the screen The load will be not added to the total 000282 IVWESC uso EN 00 TRI 46 5 Weighing System User Manual I View Excavator English 5 2 1 Remote Booking Switch The remote booking switch it s an external button that has the same functionality of the button a of the control box When installed it s usually placed on the excavator joystick Can be also replaced by an available internal button of the joystick itself
9. Press C to confirm The icon off 000282 IVWESC uso EN 00 TRI 119 I 4 Digging System User Manual I View Excavator English 4 4 2 Laser beam acquiring The reference with the laser beam is done rising the laser receiver sensor trough the laser beam The rising movement has to be done at constant and moderate speed The speed indication is shown on the screen with a graph bar inside the info box Keep the speed indicator inside the bar To have a constant speed in the moment that the laser beam is crossed start with the receiver at least a couple of meters below the laser beam plane before to start to rise the boom Relative Reference Laser e Set the Relative Laser mode The LASER message will appear into the infobox together with the vertical speed graph bar Take care that the laser level is switched on High rpm is preferred e Perform the laser acquisition and you will see the OK message into the infobox e Move down the booms laser receiver below the laser level until the message OK will be replaced with REF 0 that means that it s possible to perform the first depth zeroing H e Putthe bucket to a defined height usually the target depth and pressing key After each acquisition the laser receiver is disabled to avoid unwanted acquisitions The message OFF will be shown To enable again the laser receiver for a new acquisition press V To manually disable press y Every tim
10. Weighing System User Manual I View Excavator English 5 7 GUSTUMER MENU System can store up to 500 different clients each with a name up to 16 characters long e From the main operating screen press Aa to access the CLIENTS menu Client if Client name setting A cbEFGHTI KLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz 0123456789 lt gt Name set 2 10 Instructions gt Use O CS to select clients 10 clients for page q gt Use to scroll clients pages gt Press lo to go back to the operating screen or exit a function gt Press Aa to return to the first client page Settings gt Press to set the client and return to the operative screen gt Press TX to enter the selected client data deletion and confirm md key Set Client name gt Press VA to set the client name gt Use Oo to select value and C to enter it gt Press to confirm value and return to the previous page 000282 IVWESC uso EN 00 TRI 159 5 Weighing System User Manual I View Excavator English 5 8 TRUCKS MENU System can store up to 500 different trucks each with a name up to 16 characters long e From the main operating screen press T to access the menu rFOANAU AW NN CH A Cc e A U A gt Use O to select trucks 10 for page gt Use 0 d scroll trucks pages gt Press gt to go back to the operating screen or exit a function gt Press a to return
11. axle Transversal Slope disabled No slope in use Transversal Slope Manual Setting mi Transversal Slope Automatic Setting 000282 IVWESC uso EN 00 TRI I 23 I 4 Digging System User Manual I View Excavator English 4 5 4 How to dig a sloped surface Reference direction Angle Zeroing parallel to the Y Axle The excavator has to start aligned parallel to this Y field No rotation sensor installed e Reference direction Angle Zeroing parallel to the Y axle e The excavator has to start aligned parallel to this Y field side e fa laser transmitter is in use the Y line generated by the laser has to be parallel too With big slopes a bad alignment can generate a heavy error Note The excavator can t be rotated Rotation sensor installed option The rotation sensor option allows to dig rotating the chassis even there are slopes set With the rotation sensor option enabled proceed as follow e Align the excavator chassis parallel to the Y axle of the surface reference direction angle zeroing KZ e Then press to save the angle A REF Y confirmation message is shown into the infobox The acquired angle it s now the zero angle of the chassis The following laser acquisitions after the machine has been moved can be taken at any rotation angle Note If NOROT instead of REF Y message is shown means that the rotation sensor is not connected or not work
12. jor r fi gt Show Totals Press amp hold PROJECT e From the Print Menu press to print the ticket e The ticket can be also printed immediately from the main operating screen by keeping pressed gt Option The ticket has to be created based on the needed information and the space on the ticket paper Every information has its proper command that has to be entered on the option menu PRINT Headerl Total truck WM Ne CDEFGHIIKLM O SCH End of the day abcdefghijklm gt Text Matrix nopqrstuvwxyz 0123456789 lt gt BAFAKALA Command example Ticket N Show Totals e To seta name select in the text matrix the desired character using the arrows and press to add it to the text in creation It s possible to use the special character lt and gt to move the cursor in the text and change correct a character A e Press 9 to confirm value and return to the previous page 000282 IVWESC uso EN 00 TRI 67 5 Weighing System User Manual View Excavator English Command string example BAFAKALA Refer to the following command list e Will print the following information with text at standard height B command e Time and Date F command e CAT command e Ticket Number K command e A command e Total truck load L command e CAT command COMMAND LIST U s O PB Normal Character C Double Width Character Doubl
13. the operating screen or exit a function gt Press Aa to return to the first project page Settings gt Press O to set the project and return to the operative screen gt Press A to enter the selected project data deletion and confirm vith key Set project name gt Press a to set the project name gt Use Q to select value and to enter it gt Press to confirm value and return to the previous page 000282 IVWESC uso EN 00 TRI 158 5 Weighing System User Manual I View Excavator English 5 10 OPERATORS MENU System can store up to 50 different operators each with a name up to 16 characters long e From the main operating screen press E to access the OPERATORS menu OPERATORS Operator 1 1 Li Bs CDEFGHIIKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz 0123456789 lt gt Name set j n to scroll operators pages 7 gt Press gt to go back to the operating screen or exit a function gt Press to return to the first operator page Settings gt Press to set the operator and return to the operative screen gt Press A to enter the selected operator data deletion and confirm md key Set operator name gt Press Ea to set the operator name gt od 7 to select value and to enter it gt Press to confirm value and return to the previous page 000282 IVWESC uso EN 00 TRI 159 5 Weighing System User Manual I View Excavator Engl
14. to the first truck page Settings gt Press to set truck and return to the operative screen gt Press VA to set the max load for all the trucks gt Press VA to set the max load that the truck can handle gt Press VA to set the truck name Delete Truck gt Press VA to enter the selected truck data deletion gt Press to confirm 000282 IVWESC uso EN 00 TRI 156 5 Weighing System User Manual I View Excavator English 5 8 1 Set max load MAX LOAD generic Enter save Home exit 8 10 e Use O gt to set value e Press to confirm value e Press A go back to the previous screen 5 8 2 Setnames Truck 1 NecperGHI JKLM NOPQRSTUVWXYZ abcdefghijklm nopgrstuvwxyz 0123456789 gt Name set e Use gt to select value and to enter it e Press 2 to confirm value and return to the previous page 000282 IVWESC uso EN 00 TRI 57 5 Weighing System User Manual I View Excavator English 5 9 PROJECTS MENU System can store up to 100 different projects each with a name up to 16 characters long e From the main operating screen press Aa to access the PROJECTS menu PROJECTS Project 1 NecperGHI JKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz 0123456789 lt gt Name set Instructions gt Use O to select projects 10 projects display for each page gt Use to scroll projects pages gt Press lo to go back to
15. 5 9 1 Buzzer function Wait Beep Wait Beep function enabled the buzzer will sound flashing when the weighing is booked The frequency changes if the boom is higher or lower than the start weigh point ON Function enabled OFF Function disabled 5 5 2 Auto Book function With this function enabled is possible to weight material that will be not loaded on the truck moving it levelling the ground that has to be manually deleted with delete partial command 000282 IVWESC uso EN 00 TRI 151 5 Weighing System User Manual View Excavator English E ON The weighing function is always enabled This function avoids to press button before to weigh The weighing procedure will be activated every time that the first boom overtakes the start weigh angle OFF Function disabled The weighing has to be tagged every time Necessary to press to tag the weight 5 5 3 Countdown function Countdown function to weigh decreasing from the truck max load ON Function active The initial value for the scalar counting is the value set as maximum load to set the maximum load see the dedicated page in this manual On activating the Countdown function the maximum load value is shown on the display Each partial is subtracted from the maximum load and the maximum load exceeded will be indicated on the screen with a warning when the load drops below zero OFF Function disabled The partial load is added to the total load at every weighi
16. LASER SPEED CONDENGATION 84 6039 NEIGHINGCORREGION S 86 T EC 87 000282 IVWESC uso EN 00 TRI 14 Index Chapters User Manual I View Excavator English Index Revision Notes Rev Index Rev Date Sw Compatibility E Revision Notes 00 10 05 2012 WS 10 23 Ven ELL RR RER RR RRE RSR RRE RSR RR RR RSR RR TENNENE RR RR RR RRE RR RR RR RSR RR RR RSR LL RR RSR RR RR LL LL LL LL LE LL LL LL LELE LL LE LL LLC LELLA 000282 IVWESC uso EN 00 TRI 15 1 Preview User Manual View Excavator English L Preview The information on this document could be subject to change without notice The constructor is not responsible for possible content mistakes or misprints that could be present in this manual Any reproduction translation or copy of parts of this manual is forbidden without prior written authorization by the constructor WARNING A Modifications not expressly approved by COBO Division 3B6 cause the loss of authorization to operate the system WARNING A Before starting operations the user should read and understand this manual and follow the contained instructions 000282 IVWESC uso EN 00 TRI 16 1 Preview User Manual I View Excavator English 2 Warnings 1 1 Use of the System The following directions should enable the person responsible for the system and the person who actually uses the instrument to anticipate and avoid operational hazards The person responsible for the instrument
17. a aa O O The complete list of the selected item with is total load is shown gt Use 0 d scroll pages gt Press to singularly zero the total of each material and confirm with To zeroing all the totals summary use Materials Total in the Delete menu gt Press Aa to return to the first page gt Press to go back to the operating screen or exit a function 000282 IVWESC uso EN 00 TRI 165 5 Weighing System User Manual I View Excavator English 5 12 STM295 PRINT MENU Print Menu for printer STM295 e From the main operating screen press 3 to access the PRINT menu PRINT Total truck Options End of the day Ticket N Show Totals o o SE Total truck Print the total load of the actual truck Options Menu of the additional information that can be enabled disabled in the ticket options page End of the day Print summary Menu Ticket N Sequential number of the printer ticket automatically increased at every total truck print to confirm gt Press W to enter the setting es or NE to set value Press J gt Press direct to return to 1 Shows Totals Totals Menu 000282 IVWESC uso EN 00 TRI 66 5 Weighing System User Manual I View Excavator English 5 12 1 Total truck Print Ticket Printing of the total load of the actual truck PRINT Total truck Options End of the day a Ticket N to k p J
18. achine to load trucks dumpers Using the system for other reasons work environment it s maybe possible to reach the system computation max values shown limits UU Please note that the shown into the numbers below it s the decimal separator sign Totalload Partialload Bucket n Target Load Display Totals max value x each material shown 999990 999990 1 999 1 999990 999999 0 01 999 99 999999 1 999990 999999 0 01 999 99 999 99 0 01 999 99 999 99 9 digits with parameter Fixed UM ON refer to the Calibration Manual 6 digits default If six digits are few it s possible to set more digits through a parameter that allows the use of nine digits this is the limit Then if the Fixed UM is disenabled OFF there are limits while if the Fixed UM is enabled ON there are another limits refer to the Calibration Manual The limits of values with nine digits and Fixed Unit ON are the following Totallo ad Partial lo ad Bucket n Target Load Display Totals max value x each material shown 200000000 200000000 1 999 1 200000000 200000000 200000000 200000000 1 999 1 200000000 200000000 0 01 999 99 200000000 999990 999990 1 999 1 999990 200000000 200000 00 200000 00 1 999 0 01 200000 00 200000 00 200000 00 200000 00 1 999 0 01 200000 00 200000 00 000282 IVWESC uso EN 00 TRI 172 5 Weighing System User Manual View Excavator English 9 digits with parameter Fixed UM OFF
19. anual I View Excavator English Manual Profile Create a profile inserting manually the profile coordinates junction points values PROFILE 1 Point Depth Bre slope PROFILE 1 Set Profile Use existing Create or Editor Delete Automatic Manual 7 o o o o o o o o o o o o o o o o o Point Profile point under editing From 1 start to 10 Depth Reach Set depth and reach values referred to the starting point First point 1 start has usually 0 depth and 0 reach other points are referred to this In case some values is set in point 0 there will be an offset of the starting point respect to the physical point where REF 0 will be done with the bucket to reference the machine to the profile Slope The Slope value is the value automatically calculated that refers to the slope segment to be done between the actual selected point and the previous gt Select function with and gt Use to set value and e to enter the setting P to confirm gt Press 9 to end the profile The graphical summary of the profile will be shown 000282 IVWESC uso EN 00 TRI 29 4 Digging System User Manual I View Excavator English 4 6 5 Graphical Summary At the end of a profile setting manual or automatic mode it s shown a summary graph Bucket actual position Graphic Bars Target Point lt Zoom number and reach 0 0 1 Depth em ep R 0 00 Y 0 00 Slop
20. cally deleted at the print end e OFF The totals database will stay in memory and incremented in case of new loads up to the use of the function Materials Total from the DELETE menu ER to set Confirm with key e Press to enter the setting and use 9 e press to return to the previous page 000282 IVWESC uso EN 00 TRI 69 5 Weighing System User Manual I View Excavator English 5 12 3 Show Totals Totals Summary Menu PRINT SHOW TOTALS MATERIALS 1 999 rota au eiei NOI EE Options 999 End of the day EI 999 999 Ticket N Project Header 1 999 Header 2 999 Show Totals eee ee eee O O The complete list of the selected item with is total load is shown gt Use 0 d scroll pages gt Press to singularly zero the total of each material and confirm with To zeroing all the totals summary use Materials Total in the Delete menu gt Press Aa to return to the first page gt Press to go back to the operating screen or exit a function 000282 IVWESC uso EN 00 TRI 170 5 Weighing System User Manual I View Excavator English 5 13 MULTI PRODUCT AND MULTI TRUCK FUNCTION Last bucket gt Total of the actually selected material that has been loaded on the truck Total load of the truck includes all the materials loaded The Multi Product function enables the possibility to load up to 10 different products on the sam
21. ce zero e Red LED ON when the bucket is higher than the reference zero e Green LED ON when the bucket is on grade e Red LED ON when the bucket is lower than the reference zero 4 1 1 Buttons Key Description Shift to the Weighing System if enabled Short press Option Menu Long press Setup Menu diagnostic and calibration functions MAAN Zero the Rotation Sensor Angle Reference Set the Depth Offset Height Target VEE I RER RR RER AR H RR RRE RSR RR RER RR RRE RSR RRE RSR RR RRE RSR RRE RSR RR RRE RSR RR RSR RR RR RER RR RR RER RRE RSR RRE R RSR RRE RER RR RR RER RR RR RER RR RR RER RR RRE RSR RRE RSR RR RR RSR RR RR RSR RR RR RSR RR RR RSR RR RR RSR RR RR RSR RR RR RSR RR RR RSR RR RR RSR RR RR RSR RR RR RSR RR RR RSR RR RR RSR 8 e Switch Off the Alarm Clock buzzer when active MAAN Zero the Depth Reach and Laser References aRRRRRRRRRRRRRR RR ly Set the Reach Offset Reach Target CLIL LL LL LE LL LL LL NENNE NNN LL LLC LL LL LL NNN NENNE NNN NNN NNN NNN NENNE NENNE NNN NENNE NENNE NENNE NENNE NENNE NENNE 000282 IVWESC uso EN 00 TRI 113 4 Digging System User Manual I View Excavator English 4 1 2 Bucket Icons The bucket icons lateral view from left side and frontal view from the cabin side are real time indications to know how much the bucket is rotated The horizontal line reflects the ground drawn in blue eventually with the relative slope The li
22. e Reach Graphic Bars Green bar Profile start Red bar Profile End Target Point Progressive point number and reach R value referred to the target point Depth Reach Slope Depth and reach values are referred to the starting point The slope in is referred to the slope section that has to be dig to reach the actual selected point gt Press or to return to the main working page gt From working screen it s possible to recall the profile summary graph with lt gt 000282 IVWESC uso EN 00 TRI I 30 I 4 Digging System User Manual I View Excavator English 4 6 6 Work with a profile It s possible to move the excavator along the longitudinal axle of the profile in case the mechanical reach of the machine is not enough or for operative comfort Press ZX to see the Set Reference icon L Put the bucket on a profile point and press to store the reach The Keep Reference icon r now show Move now the excavator and put the bucket on the previous stored point Vv VV V WV Press to complete the procedure and continue to work The profile icon is show again a It s possible to jump out from the procedure at any moment pressing gt 000282 IVWESC uso EN 00 TRI 131 I 4 Digging System User Manual I View Excavator English 4 7 MEMORY FUNCTION The memory function provides a way to move the excavator when you are not using a laser as a reference eg
23. e Height Character EE Double Width and Height Character Time and Date Material Code Operator Code Ticket Number Total Load truck ufo as Truck Code XYZabcde Truck Name number plate each character is a name line up to 8 lines Project Code hinn Project Name each character is a name line up to 8 lines 000282 IVWESC uso EN 00 TRI 1 68 5 Weighing System User Manual I View Excavator English 5 12 2 End of the day At the end of a truck load when the Delete Total function is used the total load shown on the display is added in a dedicated memory that creates the history summary of the loaded material called totals end of the day summary Is recorded all the material loaded separated by Materials Enable disable the totals to print PRINT END OF THE DAY Total truck Print Summary Options 4 Materials ON Ticket N 1 Delete after the printing OFF Show Totals Print Summary Entering the page End of the day is possible to start immediately the print pressing again over Print Summary and will be printed the total of every item Eventually it s possible to choose what has to be printed OFF ON Note this printing can t be customized so be careful about the paper size quantity of data Print Materials Enable disable the totals to print separated by materials ON OFF Delete after the printing e ON The totals database will be automati
24. e depth height zeroing reference is done with the laser beam acquisition 000282 IVWESC uso EN 00 TRI 117 I 4 Digging System User Manual I View Excavator English 4 3 2 Reach Offset Setting Set the Reach Target the horizontal distance from the acquired reference value A From the operating screen Press p to enter the setting its value R will start to flash Use O to set value or 9 to fast zero it Press 9 to confirm From now on the reach target is the reference zero value acquire plus minus the set offset value 000282 IVWESC uso EN 00 TRI 118 4 Digging System User Manual I View Excavator English 4 4 LASER FUNCTION 4 4 1 Laser Setting p White BAR speed OK Red BAR speed out of range lt LASER FUNCTION Laser Speed Bar nl LS Laser not in use disabled Confirming this option the corrections taken by using the laser are not considered and enabling again a laser mode means that the laser acquisition has to be done again Laser in use enabled With a laser transmitter it s possible to refer the machine to the laser beam and work at a fixed height to the laser level itself instead to transport a quote from different landmark Set Laser Function From the operating screen e Press di to enter the Laser function e Press again GA to set the desired Laser mode disabled relative absolute The icon of the selected function will start to flash e
25. e that the excavator has been moved a new laser acquisition has to be done The REF 0 procedure is no more needed the reference in use distance from laser to target height still the acquired on the first laser caught and you will continue to work at the same distance from the laser Absolute Reference Laser Differently from Relative Laser instead to reach with the bucket the target height and do a REF 0 it s possible to manually set a depth value and the target height zero depth will be at that distance from the laser beam e Set the depth offset from laser beam to the final ground depth If the laser is 5 meters higher set 5 00 meters e Set the Absolute Laser mode e Proceed as with Relative Laser Just after the first acquisition the REF 0 procedure is no more needed and the system is ready to dig OK message on the screen the depth zero value will be at the desired height 000282 IVWESC uso EN 00 TRI 20 4 Digging System User Manual I View Excavator English 4 5 SLOPE FUNCTION ll an Y AXLE SLOPE X AXLE SLOPE SLOPE FUNCTION gt Ia Y Axle standard Longitudinal Slope Transversal Slope Positive Positive slope slope 4 5 1 Set Slope function Slopes Settings e Longitudinal standard and transversal slopes disabled e Slopes manual settings e Slopes automatic settings gt Press A to enter the Slope function gt Press again Wa to set the Slope mode gt Press to co
26. e truck The operator can load on the same truck different materials See this example 1 Select as usual the first material to load GRAVEL and start to fill the truck 2 After one or more buckets the operator is free to select another material SAND and start to load this material 3 When the quantity of the second material is enough the operator can select a third material to load or return to the first GRAVEL in this example continuing from the previous value of load reached If you have used the Multi Product function during the load of a truck you can see in the printer ticket the total truck load as usual and the single load of each material The system memorizes these data at the end of the truck load as usual delete total keeping the correct load for every material The Multi Truck function is always enabled and is completely transparent by the operator Changing the truck selected during a load Total Load gt 0 system freezes in memory actual load and it starts again to load from 0 Then you can finish the second truck usually with print total and delete total and load again previous truck selecting it s code previous values are restored on the display NOTE using Multi Product and Multi Truck all the partial values are lost switching off the system during a load 000282 IVWESC uso EN 00 TRI 171 I 5 Weighing System User Manual I View Excavator English 5 14 MEASURE UNITS The system is designed to use a m
27. er beam acquisition 000282 IVWESC uso EN 00 TRI 115 I 4 Digging System User Manual I View Excavator English 4 2 2 Depth Offset Setting Set the Height Target the vertical distance from the acquired reference value A From the operating screen ei I to enter the setting depth value will start to flash gt Press gt Use CS to set value or o to fast zero it gt Press O to confirm From now on the target height is the reference zero value acquire plus minus the set offset value 000282 IVWESC uso EN 00 TRI I 16 I 4 Digging System User Manual I View Excavator English 4 3 REACH FUNCTION Remember that the values are referred to the bucket blame centre 4 3 1 Reach Reference Zeroing Bucket on grade Zero reach Set the Reach Reference 0 From the operating screen Position the bucket on the ground in a desired reference point A Keep pressed o to zero the reach value From now on the display will show the reach zero respect to the reference point acquired The reach closer to the cabin is negative going away positive Bucket too close Negative reach A Bucket on the reach Bucket too far zero reference Positive reach Every time the machine will be moved it s necessary to take again the reference zero point Note If the laser function is enabled the system does not zero the height on pressing the depth key because it is in wait for laser beam condition and th
28. f the bucket if the sensor isn t mounted completely parallel with the Y axis of the machine CALIBRATION Digging Mounting Compens Bucket Bucket Y Axle Calibration Set Y to 45 45 deg 90 90 deg Bucket Axles actual angles gt Press to go back to the operating screen e Put the bucket perfectly horizontal zero degree X using laser or a reference instrument and try to have chassis horizontal too e Move Y Bucket longitudinally in out The X angle must be always 0 for every Y angle If not to compensate the installation move the Y axis to e Select the proper calibration and press to perform the compensation 000282 IVWESC uso EN 00 TRI 82 6 Calibration Mode User Manual I View Excavator English 6 1 3 None Grab Setting CALIBRATION Digging Length gt Press S to go back to the operating screen 000282 IVWESC uso EN 00 TRI 83 6 Calibration Mode User Manual I View Excavator English 6 2 LASER SPEED COMPENSATION This procedure improves the laser accuracy especially compensating the laser acquisition delays due rising speed Before to start the calibration set the depth distance between the laser beam level and the reference point on the ground example 4 00 if the reference point if 4 meters below the laser CompL Low speed Compensation Laser Speed Indicator Low speed e Press Ga to enter in the laser selection mode Si
29. iew Excavator English 4 11 3 Alarm Clock When the alarm occurs the buzzer will irregularly sound and the time indication in the working screen will became red 1st Alarm Clock is used to sound at a specified time 2nd 0 Alarm Clock sound always at the same time like start and end of the day CLOCK SETTI OFF Hour alan Minutes mm Day DD OPTIONS Brightness 100 Graphics Clock Settings Month MM Key Beep OFF Remote Beep OFF Touch Point Ci Machine N 1 CLOCK SETTI f Hour Minutes CLOCK SETTI Hour Minutes About CLOCK SETTI CLOCK SETT OFF ON Enable disable ON OFF the desired alarm clock Hour Minutes Day Month Y ear Alarm Clock Settings Change the alarm clock time over the proper line lt gt to select function and W to enter the setting e Use I to set the desired value and press confirm 9 press to exit e Press to disable the alarm 000282 IVWESC uso EN 00 TRI 141 4 Digging System User Manual View Excavator English Weighing System The system is based on the measurement of the pressure of the lifting cylinder in the rising phase by means of the pressure transducer and the calculation of the up speed with an inclinometer 5 1 MAIN OPERATING SCREEN In the working screen is possible to check the truck load and all the active functions MAX LOAD Da mmm mio Weighing Database Ce Ai Ref Descriptio
30. ing 000282 IVWESC uso EN 00 TRI I 24 4 Digging System User Manual I View Excavator English 46 PROFILE FUNCTION A profile is the sequence of more different slopes along the same axle Y Differently from the single slope it s possible to cross all the slopes without additional setting during the work PROFILE FUNCTION ACTIVE gt This icon shows that a profile is in use A single slope set before is no more considered when this icon is shown Info box In this box PROFILE is shown the following profile conjunction point that has to be reached closer to the cabin and the reach distance to it R 000282 IVWESC uso EN 00 TRI 25 4 Digging System User Manual I View Excavator English 4 6 1 Set Profile function Select in this page the profile that has to be edited or used It s possible to keep saved up to 4 different profiles e From the operating screen keep pressed EZ to enter in the Profile Selection page PROFILE selection Disabled Press amp hold P rofi le 1 Profile 2 Profile 3 Profile 4 Profile 1 Disabled No profile in use and return to the main working page Profile 1 4 Enter the selected Profile Menu PROFILE PROFILE IR gt Selected Profile Selection Use existing Active the profile Disabled Create or Editor Create or change the profile Profile 2 Profile 3 Profile 4 Delete Delete the profile NN I IE e e eE 8 to se
31. is function allowed to select the bucket calibration to use The calibration of each bucket can be done by the system installer or directly by the user following the instruction at the end of this manual 0 0L O O0O0R me 0 00 Y 0 00 X V J E i ay BUCKET e Press Gk to enter the function e Select the desired bucket with Or D e Press to confirm and exit from the setting NOTE if the control box is used on 2 different excavators machine 1 and machine 2 the 9 buckets are shared between the 2 machines 000282 IVWESC uso EN 00 TRI Ei 4 Digging System User Manual I View Excavator English 4 11 OPTIONS MENU x I e From the operating screen press to enter the Options Menu OPTIONS Brightness Graphics Clock Settings Alarm Clock Key Beep Remote Beep Touch Point Machine N Brightness Display brightness settable from 0 to 100 Graphics Menu to set the display item colours Key Beep OFF no sound when a control box button is pressed ON sound when a control box button is pressed Remote Beep Touch Point Machine N System can store up to 2 calibrations same control box on 2 different machines Select here the machine in use Clock Settings Time and date setting menu Alarm Clock Alarm clock setting menu to select function and W to enter the setting or menu to set function and to confirm 000282 IVWESC uso EN 00 TRI 38 4 Digging System User Man
32. ish 5 11 STP6 PRINT MENU Print Menu for printer STP6 e From the main operating screen press a to access the PRINT menu PRINT Total truck Options End of the day Ticket N Header 1 Header 2 Show Totals Total truck Print the total load of the actual truck Options Menu of the additional information that can be enabled disabled in the ticket options page End of the day Print summary Menu Ticket N Sequential number of the printer ticket automatically increased at every total truck print 22 to set value Press to confirm gt Press W to enter the setting VP H gt Press gel to return to 1 Header 1 Header 2 First and second header of the ticket Shows Totals Totals Menu 000282 IVWESC uso EN 00 TRI 60 5 Weighing System User Manual I View Excavator 5 11 1 Total truck Print Ticket English Printing of the total load of the actual truck The ticket has various additional information that can be enabled disabled in the ticket OPTIONS menu PRINT Total truck Options End of the day Ticket N Header 1 Header 2 Show Totals e From the Print Menu press HERDER 1 EI OG TE 12 13 Ticket N 4 HEADER 3 Materla Sand El lent 1 Carlos Truck AAI EG Project Continental Dporatgr 1 Frank Bucket N J Tatal 3 27 ton to print the ticket Press amp hold GO Down
33. key function Materials Total from the DELETE menu e Press to enter the setting and use I e be to return to the previous page 000282 IVWESC uso EN 00 TRI 163 5 Weighing System User Manual I View Excavator English 5 11 4 Header1 2 It s possible to customize the ticket header PRINT Header 1 NecDEFGHII KLM NOPQRSTUVWXYZ abcdefghijklm Total truck Options End of the day nopqrstuvwxyz Ticket N an 0123456789 lt gt Header 1 Header 2 A Show Totals dadap Si Si Si Si Si SE Header 1 2 In the ticket header 1 it s possible to set 8 lines of 16 characters that will be printed at the beginning of the ticket In the ticket header 2 it s possible to set 8 lines of 16 characters that will be printed below the date and time e To seta name select in the text matrix the desired character using the arrows and press to add it to the text in creation It s possible to use the special character lt and gt to move the cursor in the text and change correct a character J e Press to confirm value and return to the previous page 000282 IVWESC uso EN 00 TRI 64 5 Weighing System User Manual I View Excavator English 5 11 5 Show Totals Totals Summary Menu PRINT SHOW TOTALS MATERIALS 1 999 rota au eein NI EE Options 999 End of the day EI 999 l 999 Ticket N Project Header 1 999 Header 2 999 Show Totals Gebees
34. lect function and press e to confirm gt Use BA d gt Press to go back to the previous screen 000282 IVWESC uso EN 00 TRI 26 4 Digging System User Manual I View Excavator English 4 6 2 Use Profile Activate the selected profile and return to the main working page PROFILE 1 use existing Create or Editor Delete 4 6 3 Delete Profile Zeroing the selected profile PROFILE PROFILE Use existing Use existing Create or Editor Create or Editor pelete Enter confirm Home exit gt Press again when requested to confirm d gt Press to go back to the previous screen 000282 IVWESC uso EN 00 TRI 27 4 Digging System User Manual I View Excavator English Automatic Profile Create a profile putting the bucket on the conjunction points between the various slopes sections to acquire the coordinates max 10 points PROFILE Set Profile EO Manual Use existing Create or Editor Delete Take Point Take Point Acquire Acquire 10 Take Point End Di e With the bucket steadily positioned on a conjunction point press to acquire The point number increases It s now possible to move to next point e Press on End command after that the last point of the profile has been taken to finish the acquisition The graphical summary of the profile will be shown 000282 IVWESC uso EN 00 TRI 28 4 Digging System User M
35. m pivot L to bucket blame M e Measure with accuracy the bucket length and set the value e Measure the angle and set the value Offset Angle correction value difference from set and read value Press to adjust X AXLE Length Width of the bucket measured straight from corner to corner A B e Measure with accuracy the bucket length and set the value 000282 IVWESC uso EN 00 TRI 176 6 Calibration Mode User Manual I View Excavator English 6 1 2 Bucket 1 Bucket Type Selection Select the bucket type to calibrate Bucket InQut Bucket Setting 1 1 Only Inout Loic sch Tilt Bucket Setting 1 2 Use CM or to select the used bucket type and confirm with N key 1 1 InQut Bucket Setting s for each boom it s necessary to set length and angle of the bucket CALIBRATION Digging only Inout Bucket S1de AXLE Y Length 0 000 Angle Y 90 0 Offset 90 0 Actual 90 0 InOut Bucket Page gt Press to go back to the operating screen Side Bucket side where the sensor is installed e Right R e Left L 000282 IVWESC uso EN 00 TRI 77 I 6 Calibration Mode User Manual View Excavator English Y AXLE Length Length of the bucket measured straight from pivot L to bucket blame M e Measure with accuracy the bucket length and set the value Angle Y Bucket angle x10 between axle from pivot L to bucket blame M and the horizontal reference
36. must ensure that all users understand these directions and adhere to them Prohibited uses e Using the system without instruction e Using outside the stated limits e Opening of the equipment by using tools screwdrivers etc e Carrying out modification or conversion of the product e Use of accessories from other manufacturers without the express approval of COBO Divisione 3B6 e Inadequate safeguards at the surveying site e g when measuring on roads power lines WARNING The chance of injury malfunctions and damage to the equipment if not used as specified The owner has to inform the user of the hazards in use protective and counter measures to take 1 2 Areas of Responsibility WARNING The person responsible for the instrument must ensure that the equipment is used in accordance with the instructions This person is also accountable for the deployment of personnel and for their training and for the safety of the equipment when in use The Person in charge of the instrument has the following duties e To understand the safety instructions on the product and the instructions in the User Manual e Tobe familiar with local safety regulations relating to accident prevention e To inform COBO Divisione 3B6 immediately if the equipment becomes unsafe 1 3 Checks the user must perform To ensure continuous and safe operations of the system the following checks must be performed regularly by the user Before to start to work with
37. n 3 1 Clock hh mm ss ee a eee FE FETE FFF EE C a A 7 Weighing Database displayed in sequence max load project operator material client truck Fem 000282 IVWESC uso EN 00 TRI 42 5 Weighing System User Manual I View Excavator English Ref Description LEDs Bar Weighing Instructions e Red LED ON move down the bucket e Green LED ON bucket on grade e Red LED ON move up the bucket Max Load Indication e RedLEDs ON actual load gt to the max load set e Green LED ON actual load lt to the max load set SETTINGS Ref Description Auto Book WI 3 A Auto Book function active GP A Auto Bock function disable Max Load Max load function non active A Te ax Load set AS lt P Max Load reached EeeeKEEEKEKEEENEKeNT GueEKEEEKEEKEEEKEEEEEKEEEEEKEEEEKEEEEKEEEKEEEEEKEKEKEKEEEKEKEEEKEKEEEKEKEEEKEKEK ENEE TTT ATA TOT TTT TANO OTTONE ENEE ENEE ATTI TO OOO 3 Tare set No Tare set Count Down Count down function active Count down function active Fon 000282 IVWESC uso EN 00 TRI 43 5 Weighing System User Manual I View Excavator English Ref Description Buzzer Function 2 b Buzzer disabled li 6 Buzzer enabled WEIGHING DATABASE Database Area with selected item number Key i a Se Materials Menu Enter the Materials Database Description Shift to the Digging System if enabled Sh
38. ne below the lateral bucket view reflects the Y slope the line below the frontal bucket view the X slope When the depth value is zero the bucket blame are on the ground line system refers indication to the centre of the blame Please note that the bucket draw is an indication and doesn t reflect the real excavator bucket shape so it s not an indication to work with the bucket bottom or with a blame corner if a X slope is in use 000282 IVWESC uso EN 00 TRI 114 4 Digging System User Manual I View Excavator English 4 2 DEPTH FUNCTION Remember that the values are referred to the bucket blame centre 4 2 1 Height Reference Zeroing Bucket on grade Zero depth Set the Height Reference 0 From the operating screen gt Position the bucket on the ground in a desired reference point A gt Press o to zero the depth value From now on the display will show the depth zero respect to the reference point acquired The depth below the reference point is negative above positive Bucket on grade Bucket too low Bucket too high Zero Depth Negative depth Positive depth no tilt indications Every time the machine will be moved it s necessary to take again the reference zero point Note If the laser function is enabled the system does not zero the height on pressing the depth key because it is in wait for laser beam condition and the depth height zeroing reference is done with the las
39. nfirm 000282 IVWESC uso EN 00 TRI 121 4 Digging System User Manual I View Excavator English 4 5 2 Y Axle slope setting Longitudinal Slope disabled No slope in use Disable slope when you work on a flat surface 0 If a value has been previously set is not considered 0 00 slope in use A saved value will be available again when the slope mode will be recalled again Longitudinal Slope Manual Setting gt Press VA to enable the manual mode Deg gt While the icon flashes use Q to set value or to fast zero it The slope is positive when higher in front of the excavator i Longitudinal Slope Automatic Setting If a piece of slope is already available you can automatically acquire is value and use it to continue to dig gt Press A to select the proper icon The SET 1 message will display into the infobox gt Press 0 to acquire the point bucket positioned on the far away point The SET 2 message will display into the infobox gt Press to acquire the second point closer to the cabin gt Press to calculate the slope The icon will stop to flash 000282 IVWESC uso EN 00 TRI EI 4 Digging System User Manual I View Excavator English 4 5 3 X Axle slope settings Icons are with a X symbol for identification The slope X is positive when higher on the left side of the excavator reference operator seated in the cabin All the functions works as for the Y
40. ng 000282 IVWESC uso EN 00 TRI 52 5 Weighing System User Manual I View Excavator English 5 6 MATERIALS MENU System can store up to 200 different materials each with a name up to 16 characters long e From the main operating screen press WK to access the menu MATERIALS MATERIALS e oe me WEE CAE WN gt Press gt to go back to the operating screen or exit a function gt Press Aa to return to the first material page Settings gt Press to set the material to weigh and return to the operative screen m gt Press T to set the material density gt L Press VA to set the material name Delete Material gt Press ZX to delete the selected material data deletion gt Press to confirm 000282 IVWESC uso EN 00 TRI 153 5 Weighing System User Manual I View Excavator English 5 6 1 Set names zZ ATERIALS Materia 1 NecDEFGHII KLM NOPQRSTUVWXYZ abcdefghijklm nopgrstuvwxyz 0123456789 gt Name set elle Be se Be WEE BWN gt Use to select value and he iat gt Press S to confirm value and return to the previous page 5 6 2 Set density ATERIALS specific Gravity to enter it ES Kg m3 0 Enter save Home exit e oe mo WEE BWN gt Use to set value available only in Kg m3 gt Press O to confirm value S CH S gt Press to go back to the previous screen 000282 IVWESC uso EN 00 TRI 54 5
41. o enter the setting and use NW NNO to set ON OFF or values I e Press fo return to the previous page 000282 IVWESC uso EN 00 TRI 162 5 Weighing System User Manual I View Excavator English 5 11 3 End of the day At the end of a truck load when the Delete Total function is used the total load shown on the display is added in a dedicated memory that creates the history summary of the loaded material called totals end of the day summary Is recorded all the material loaded separated by Materials Clients Trucks and Projects PRINT END OF THE DAY Total truck Print Summary Options End of the day Ticket N 1 Header 1 Header 2 Print Materials Clients Trucks Projects Show Totals Print Names ECH Print Summary Delete after the printing Pressing will be printed the total of every item Eventually it s possible to choose what has to be printed Print OFF ON Print Materials Clients Trucks Projects Enable disable the totals to print e ON Total to print e OFF Total not to print Print Names Enable disable the printing of the eventually materials clients trucks and projects names e ON Print names e OFF Not print names Delete after the printing e ON The totals database will be automatically deleted at the print end e OFF The totals database will stay in memory and incremented in case of new loads up to the use of the ST to set Confirm with W
42. ompared to a certified weigh bridge for example it s possible to tune the accuracy using the correction function and adjust it with a variation The correction must be the same as the found error MENU System Setup Diagnostic J Press amp hold Correction e From the main operating screen Digging or Weighing keep pressed Will be displayed the Setup amp Diagnostic menu System Setup Refer to the Installation and Calibration Manual Correction Speed Compensation Setting This correction value is directly applied to the measured load In the speed compensation is limited from 70 to 130 If a limit is reached usually something in the calibration is not good like reference speed different from calibration or too slow e Press to enter the setting and use O Q to set Confirm with key e Press n to return to the previous page Example If the system weights 5 less than the real weight the value of correction must be increased of 5 percentage points If the system weights 5 more than the real weight the value of correction must be decreased of 5 percentage points 000282 IVWESC uso EN 00 TRI I 86 6 Calibration Mode User Manual I View Excavator D Alarms During the normal work if the control box doesn t receive a sensor the alarm page will appear Please note that if the problem is a broken cable all the sensor after the failure in the line will be in alarm I
43. or English Offset Angle correction value difference from set and read value e Press ENTER to adjust 2 Tilt Setting page CALIBRATION Digging Tilt Bucket Length value to set Angle value to set Length 0 000 L ad Angle h y Angle value adjusted Offset 0 0 Actual 0 0 Length Length of the bucket measured straight from the pin A to the tip of the tooth blade B Pin A is the tilt bucket transversal inclination centre of rotation e Measure accurately the length of the bucket currently installed and set the value Angle Angle of the projection A B as described for InOut Bucket calibration Angle Y e Measure the angle and set the value Offset Angle correction value difference from set and read value e Press ENTER to adjust 000282 IVWESC uso EN 00 TRI 80 6 Calibration Mode User Manual I View Excavator 3 Pivot Setting page CALIBRATION Digging Tilt Pivot Angle Offset Actual Angle Angle of the bucket lateral inclination pivot e Measure the angle and set the value If A is higher than B then the angle is positive same convention as booms Offset Angle correction value difference from set and read value e Press ENTER to adjust 000282 IVWESC uso EN 00 TRI 1811 English 6 Calibration Mode User Manual View Excavator English 4 Mounting Compensation page This optional calibration is needed to correct the X angle o
44. ort press Enter Option Menu Long press Enter Setup Menu diagnostic and calibration functions Ee z LL LL NNN NENNE NENNE NNN NNN NNN NNN NNN NENNE NNN NENNE NNN NNN NENNE NNN NNN NENNE NENNE NNN NENNE 000282 IVWESC uso EN 00 TRI 44 5 Weighing System User Manual I View Excavator English Description Short press Enter Printer page Long press Print ticket Enter the Weighing Angle Setting Switch Off the Alarm Clock buzzer when active LELLO LL LOL LL LLC NENNE NENNE NNN NENNE NNN NENNE NNN NNN NENNE NENNE With the digging system enabled together with the weighing system pressing down key will appear the depth indication instead of the truck icon truck load graph bar 000282 IVWESC uso EN 00 TRI 45 5 Weighing System User Manual I View Excavator English 5 2 WEIGHING PROCEDURE During the weighing phase it s necessary to gt Keep the machine ona levelled ground gt Dont move the machine gt The bucket should be completely closed when you start the weigh or at the correct angle position if bucket angle check has been enabled and can t be manually moved during the weighing phase Don t move the dipper stick On a 3 booms machine the middle boom boom 2 has to be completely open Don t stop the movement dynamic weighing VV V Y Keep a constant speed Weighing Instructions Tag Weight EE eegen A J O Ze Partial Load gt Total
45. otal truck gt Press to cancel the total load before start a new truck loading Partial x 2 TRUCK FILL RESIDUE MATERIAL When the last bucket load did not empty completely to find out the effective total quantity unloaded weigh the material which has remained in the bucket and use this function This function will remove twice the last value weighed from the total so that you can find out the total value of material which has really been put into the truck gt Use NW to select the function and press e to enter Materials Totals To delete the totals in the memory example material summary totals gt Use 3 to enter gt Press to confirm the deletion 9 gt Press to go back to the previous screen Once confirmed the screen goes back to the operating screen to select the function and press 000282 IVWESC uso EN 00 TRI 150 5 Weighing System User Manual I View Excavator English 5 9 OPTIONS MENU e From the main operating screen press to access the menu OPTIONS Brightness 100 Graphics Key Beep OFF Walt Beep ON Clock Settings Alarm Clock Auto Book Countdown Mach ne N NO to select functions and KI to access the setting NS to enable disable functions and W to confirm 9 gt Press to go back to the operating screen Brightness Graphics Key Beep Clock Settings Machine N This functions are described in the Digging Mode Options Menu
46. r Manual I View Excavator English 4 Digging System 4 1 MAIN OPERATING SCREEN mm TIN br e HE d i Wald Functions Area MI 2 Lille NG eg UI i a f bhii A Description Graphical indication the relative depth cm 000282 IVWESC uso EN 00 TRI 111 4 Digging System User Manual I View Excavator English FUNCTIONS AREA Ref SE a Depth function p Longitudinal Transversal Y amp X Slopes disabled DJ p Longitudinal Transversal Y amp X Slopes manual setting DW Longitudinal Transversal Y amp X Slopes automatic setting Profile active IEEE uu NNN NNN NNN D D D WE Buzzer Function buzzer disabled buzzer enabled GevereeeEEEKEEEKEENG deveEeeEKECEEKEEKEEEKEEKEEEKEEEEEEKEEEEKEEENEEKEEEKEEKEEEKEEEKEENEEEKEEKEEEEEKEKEEKEKEKEEKEKEKEKEEEKEKEEEKEKKEEEEKEKEK ENEE ATTO TATO ono EE ek LG Max amp Min Limits Function No limits set KR Maximum Height set v Minimum Depth set v Maximum amp Maximum limits set MAX Maximum Height reached x min Minimum Depth reached LEG Laser Function em Um Laser disabled EJ Relative laser enabled ki Absolute laser enabled 000282 IVWESC uso EN 00 TRI 12 4 Digging System User Manual I View Excavator English Ref Description LEDs Bar e Red LED ON when the bucket is one meter higher than the referen
47. r Manual I View Excavator English 4 8 3 Min Depth Min Depth reached eg Min Depth set min Enable Disable limit e Press VA when the excavator it s at the maximum desired height The Min icon will start to flash EEEE e Press to confirm exit from mix height setting e Toexit without changes press T until the No limits icon will start to flash Press to confirm The icon indicates a max limit set During the work reaching this height the H MIN message will be shown into the infobox and the buzzer will sound 000282 IVWESC uso EN 00 TRI 35 4 Digging System User Manual I View Excavator English 49 BUZZER A Z 0 01 mo TT i f mm HATH d Wl NAA i I i H H UNE du IT OTER Int wm WUT d ORRE IE H AN i 0O 00R Buzzer m SP ae Buzzer nn nti x ra ctl disa b le d Ee WEE dea x Pia en a b le d tal Buzzer Enabled Buzzer steadily sounds when the bucket is on grade and discontinuously sounds away from zero depth by buzzer Disabled Bucket position doesn t affects the buzzer sound disabled e Press WA to enter the function The Buzzer Icon will start to flashes e Press again to select the desired mode e Press to confirm and exit from the setting 000282 IVWESC uso EN 00 TRI 36 4 Digging System User Manual I View Excavator English 4 10 BUCKET FUNCTION Control box can store up to 9 different buckets Th
48. system e Measure the angle and set the value 90 0 Offset Angle correction value difference from set and read value e Press ENTER to adjust X AXLE Length Width of the bucket measured straight from corner to corner A B e Measure with accuracy the bucket length and set the value 000282 IVWESC uso EN 00 TRI 178 6 Calibration Mode User Manual I View Excavator English 1 2 Tilt Bucket Setting BUC ke t CALIBRATION CALIBRATION CALIBRATION TT Digging Digging Digging Bucket Only Inou Side L Tilt Bucket Tilt Pivot AXLE Y Length 0 000 Length 0 000 Angle 0 0 Angle Y 90 0 Angle 0 0 Offset 90 0 f offset 0 0 offset Actual 90 0 Actual 0 0 Actual AXLE X Bucket Setting page Tilt Setting page Pivot Setting page CALIBRATION Digging Mounting Compens Bucket Set Y to 45 deg 90 deg 1 Bucket Setting page CALIBRATION Digging Bucket Side Refer to InOut Bucket Calibration AXLE Y Length 0 000 Angle Y 90 0 Offset 90 0 Actual 90 0 AXLE X Angle value to set AXLE X Length value to set AXLE X Length Bucket length Refer to InOut Bucket calibration Angle X Bucket angle x10 between axle A B and the horizontal reference system e Measure the angle and set the value X 0 for A B X lt 0 negative for A lt B X gt 0 positive for A gt B 000282 IVWESC uso EN 00 TRI 179 6 Calibration Mode User Manual View Excavat
49. t s also possible that if there s a short circuit in the line all the angular sensor will be in alarm English The user can verify the status of the cables connectors and restart the control box to see if the problem persist In this situation the system can t be used and it s only possible to enter in the system menu diagnostic and eventually in the calibration section with the proper password ALARMS Chassis Boom Boom2 BOOM3 Bucket Pression Low C Pression High C Rotation Alarms 1 Chassis Chassisnot found 2 Boom1 Boom 1 not found 3 Boom2 Boom 2 not found 4 Boom3 Boom 3 not found 5 Bucket Bucket not found Pressure Transducer not found 6 Pressure LowC 7 PressureHighC Pressure Transducer not found Rotation too fast for five seconds 8 Rotation 000282 IVWESC uso EN 00 TRI 87 Active on Digging S1 Digging amp Weighing S3 Digging S1 Weighing S2 Digging amp Weighing S3 Digging S1 Weighing S2 Digging amp Weighing S3 Digging S1 Weighing S2 Digging amp Weighing S3 Digging S1 Digging amp Weighing S3 Weighing S2 Digging amp Weighing S3 Weighing S2 Digging amp Weighing S3 Digging S1 Weighing S2 Digging amp Weighing S3 7 Alarms The details contained in this document are only supplied as a way of information They may be changed without notice and must not be intended as binding for C O B O S p A All rights reser
50. the lowest or highest point of the excavator Indication on the display can have also a delay when the excavator is moved fast 4 8 1 Limits off WA i im ight Mi ii e Press to see the icon of the limit to delete Max Height Min Depth will start to flash i I e Press to erase the set value The A or Hi icon off and exits from the setting 000282 IVWESC uso EN 00 TRI I 33 I 4 Digging System User Manual I View Excavator English 4 8 2 Max Height Set Height UR Actual Height ume Vax Height reached gre pp Max setting Max Height It s possible to save a maximum height when the excavator reaches this elevation a warning on the screen is shown It s used the highest pivot of the excavator MAX Set max limit a r _ e Press when the excavator it s at the maximum desired height The Max icon will start to flash In the infobox the actual height value will flashes e Press to confirm max height setting a O e Toexit without changes press until the No limits icon will start to flash M Press to confirm vw The icon indicates a max limit set During the work reaching this height the H MAX message will be shown into the infobox and the buzzer will sound E E E EE n d N A f NN d IN N f A N N Al f LA P Ly fl L ee V VU 000282 IVWESC uso EN 00 TRI 34 4 Digging System Use
51. the system following checks should be made e Cable integrity and connectors tightening 000282 IVWESC uso EN 00 TRI 17 2 Warnings User Manual View Excavator English e Angle Sensors integrity and tightening 1 4 Hazards in Use All users must follow the safety instructions given by the manufacturer and the directions of the person responsible for the instrument WARNING The absence of instruction or the inadequate imparting of instruction can lead to incorrect or prohibited use and can give rise to accidents with far reaching human material financial and environmental consequences 000282 IVWESC uso EN 00 TRI D 2 Warnings User Manual I View Excavator English 3 Characteristics 3 1 VIEW2 3 1 1 Panel View2 Description LEFT RIGHT ARROWS KEYS Refer to system in use Digging or Weighing Pu i ui ui Wi uu UP DOWN ARROWS KEYS Refer to system in use Digging or Weighing ENTER KEY Refer to system in use Digging or Weighing CLIL LL LL LL LL LL LL LL LL LL NENNE RR LL LL LL LL LL LL LL LL NNN NNN NNN NNN LELE LL LL LL NENNE NNN NNN NNN NNN NENNE NENNE NENNE 000282 IVWESC uso EN 00 TRI 19 3 Characteristics User Manual I View Excavator English View2 3 Description SETTINGS KEYS Refer to system in use Digging or Weighing FUNCTION KEYS Refer to system in use Digging or Weighing 000282 IVWESC uso EN 00 TRI 110 3 Characteristics Use
52. ual I View Excavator English 4 11 1 Graphics Is possible to change the control box display item colours The colour number is shown together with an example box COLOURS Menu Text D Menu Backgr 0 Oper Text 4 Oper Sky 248 Oper Ground 243 Icon Backgr 0 OPTIONS Brightness Graphics Clock Settings Alarm Clock Key Beep Remote Beep Touch Point Machine N About Load Default Load the default settings SAVE It s necessary to press over SAVE to keep the change the next time the system will be powered on PD KH e Use to select item and D to enter the setting The colours palette will be displayed e Inthe colour palette use arrows keys up down left right to select the desired colour and enter key to confirm Dt W i gl Colour selected Selected 000282 IVWESC uso EN 00 TRI 39 4 Digging System User Manual I View Excavator English 4 11 2 Clock Setting Control box clock setting OPTIONS CLOCK SETTING Brightness 100 Hour 10 Graphics Minutes mm Clock settings Seconds sed Alarm Clock Day i i Ned OFF Month MM Remote Beep OFF Vear Touch Point Ci Mach ne N 1 CONFIRM e Use to select function and to enter the setting e Use O to set the desired value and press confirm e Press over CONFIRM to save e Press to exit without changes 000282 IVWESC uso EN 00 TRI I 40 I 4 Digging System User Manual I V
53. uso EN 00 TRI 74 6 Calibration Mode User Manual I View Excavator English 6 1 1 Dog Bone 1 Dog Bone Setting Dog Bone setting must be done before the bucket setting next page Bucket CALIBRATION Digging SeglLength 0 000 Seg2Length 0 000 Seg3Length 0 000 Seg4Length 0 000 SeglAngle Offset p e Press W key to scroll next screen Seg Length Seg2 Length Seg3 Length Seg4 Length 1 2 3 4 referring to the picture e Measure the four segments the bones of the dog bone and set lengths into the proper line Seg1Angle Seg2Angle referring to the picture e Measure the segments1 amp 2 angles the bones of the dog bone and set values into the proper line P A 90 0 Measure the inside angle between the segment axle from pivot to pivot and the system horizontal axle Positive angle above horizontal axle Negative angle under horizontal axle 90 0 Offset Angle correction value difference from set and read value Press 9 to adjust Note Changing the DogBone setting means that the bucket setting must be done again 000282 IVWESC uso EN 00 TRI 175 6 Calibration Mode User Manual I View Excavator English 2 Bucket Setting CALIBRATION Digging AXLE Y Length 0 000 Angle Y 90 0 offset 90 0 Actual 90 0 AXLE X Length 0 000 gt Press p to go back to the operating screen AXLE Y Length Length of the bucket measured straight fro
54. ved Any reproduction adaptation or translation of this material with the exception of those cases allowed within the prescriptions of copyright laws are strictly forbidden unless expressly authorised in writing by C O B O S p A The only guarantees of C 0 B 0 S S p A products or services are those outlined in the actual warranty documents accompanying such products or services Nothing contained in this document shall be considered as an additional guarantee C O B O S p A shall not be responsible for any technical or printing errors or omissions contained in this document C O B O S p A is a trademark registered in Italy Any reference to companies or marks in this document is strictly coincidental its inclusion is only for illustration purposes and excludes any ulterior motives Any names and terms used in this document are the exclusive property of C O B O S p A TER 3B6 OCOROO C 0 B O S p A Divisione 3B6 Headquarters Via Sivo 74 C O B O S p A 28053 Castelletto Sopra Ticino Novara Via Tito Speri 10 ITALY 25024 Leno Brescia Tel 39 0331 9286 1 ITALY Fax 39 0331 972160 Tel 39 030 90451 3b6 3b 6 it Fax 39 030 9045330 www 3b6 it info cobospa it www cobospa it
55. vs 33 402 Macherio 34 EEE TE EEE 35 2 BUZZER Lene 36 4 140 BUCKET FUNG TOM eee 37 AA OO TOS EE 38 dii NN 39 4 11 2 Clock Setting E 40 4 11 3 Alarm Clock RR 41 5 AEE SEL RE 42 5 1 MANOPFERATNGSCREEN lille 42 52 WEIGHING ee RUE 46 52 1 FTP SMN 47 9 2 2 VENN 48 EE ss ON 49 5 4 PARTALL TOTAL DELETION sesescscococsceossevsceupsevsceusseusceussevssoussdvexeussivexeussiveneessiuneusiveneusiv nesen snusen 50 JE UPTON MENU EEE 51 551 Buzzer function Wait BOC sasiccscscincscpexceesesesenesenoeeuenenensnesdeacitnen cpasdenstnesdpendsastnendvendesndnestnandawssacaebes 51 5 5 2 AUOBIOKIUNCIO ee ae ee ee ee 51 5 5 3 Countdown function Lunenmidaneberdtnimejevinebneindeinlrrdnsbenieshesinetneiesteninndevlasientt 52 30 le Ess 2 53 Sol EEE EEE EEE EEE EEE EE EE 54 et Cl EEE oe root 54 000282 IVWESC uso EN 00 TRI H Index Chapters User Manual View Excavator English TE CUSTUMER E li 55 50 TRU H E 56 Ao LO AGN EEE E E E 57 0 02 Scale 57 5 9 PROJECTS MENU NEE 58 5 10 OPERATORS MEN ccnccuncorncdeacscpedenascncectudusssuseeussdusesussdveseussdvsneussdusneussiusasussuneu ssi aeu sine stmeaemeuseilt 59 e HR ERE 60 Se Print WICK GU eege 61 AER Ga EE 62 3 BOTN NEON talee 63 TN a ee ee ee 64 NE 65 ch KACKEN 66 5 121 Total truck Print TICKET EEE 67 9422 ERC 69 23 DION ore EEE E 70 5 13 MULTI PRODUCT AND MULTI TRUCK FUN TONN 71 id MERE Le 72 6 CDEN oo E 74 TELE GERNE NN 74 Dili Re ET 15 EE PU TI 6 1 3 None Grab EEE 83 6 2

User Manual I. View Excavator

Contents

Download Pdf Manuals

Related Search

Related Contents