Link Gate A FXO Manual V1.0
Contents
1. Link Gate A FXO Link Gate A FXO PBX PSTN PWE Manual V1 0 Linkcom France l 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved Index l BOSC IEOU SS eee A ee ee ee eee eee 3 2 Possibilities of unit INSTAIATIONS cccscsscscsccccccccscscsccccccccscscsccccscccscscscecsscscscecscecescscces 3 2 1 basic connection All calls are terminated Over GSM cccccscscccscscccscscscscscscscscscscscscscecs 3 2 2 Installation between PBX phone and PSTN IING cccssccssccsseccssccesccnsceesccescecescessceesceesces 4 2 3 MODY EXTENSION ne na en EE rer te ar err Trt 5 24 CUB AC EE cw EEE AE EEEE EA 6 3 MoO ee 7 Sols Qualy oF GSM Signal ae NEEE EER 8 3 2 C Nnechon OF CTO IA acest a eee san sde de eee eee sn 8 NCI cacti A 8 3 4 The most often problems during Blue Gate compact installation 8 35 LS EE 9 COM OA te dea cece sacoceneseeeesecesatdeceesetaeereeeteccssteussececeesacucas 10 4 1 Notes to each parameters ssseseesesessoesecreseseoscsoecscseseseososcseseecosososesescoserosesosesessosososeseseesosoeee 10 BZ TADIS 0 No Cole den MUN LS N A EA ai 12 4 3 Tones on lines of GSM unit sseseeseesessessossossessessessessessessesoescesoescesoesossoesossoesoesoesossoesoesoesoesoesoee 13 AA LED SIONO La Le E E 14 5 Technical DOME ae dan ous a aan ee 15 Linkcom France 2 11 rue du S2. After calling to Link Gate A FXO you get busy tone The SIM card requires PIN which is not preprogrammed or has been preprogrammed wrongly e The yellow LED blinks every two When pick up you hear a busy tone Link Gate A FXO is not log into GSM network bad signal e The yellow LED flashes depending on GSM signal strength When pick up the green LED doesn t turn on and there is no tone Analogue line is interrupted or there is a big resistance in current loop for example cable is too long between PBX and Link Gate A FXO e The yellow LED flashes depending on GSM signal strength and the green Led is on The PBX hold the line open By calling the gateway you can remove this issue In other cases check PBX manual e The Link Gate A FXO works but calls are disturbed by interference Incorrect position of antenna to telephone line Change antenna position Note Default you make by parameter 99 in programming mode see programming table at page 15 All LEDs flashing as well as tone types are mentioned in tables at the end of this manual 3 5 USB The Gate is equipped with a USB port for direct control of GSM module Siemens TC35i or MC35 or MC39 for GPRS via virtual COM port You will be able fo use ordinary GSM modem for data transmission internet connection or for SMS messages When unit is working as GSM modem then is busy for voice connection When you pick up the line you will hear busy tone The unit is monitoring d
3. case of PSTN line disconnection or failure all calls are automaticaly forwarded to GSM Back up security e When you pre program directions to GSM 9 memories of Ito 4 digits prefixes then allowed directions are routed via GSM the remaining via PSTN line when is connected e When you activate wait for dial to CallBack into PSTN line it can be use during callback either dialing into connected PBX phone or getting access to PSTN line eventually Used speed dial for PSTN line e The Mobility Extension is intended to transfer calls from PSTN line to GSM mobile phone When forwarded call from PSTN line to your mobile is rejected you can activate the SMS feature which informs you about the missed call by SMS Linkcom France A 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved E BS 2 3 Mobility Extension oo m HE Using the Mobility Extension feature allows you to do not miss any incoming calls even if you are out of office When an incoming call from PSTN line connected to a PBX phone starts ringing and is not picked up 3 rings the unit dial automatically a pre programmed number for example your mobile phone Your mobile phone will ring then simultaneously with PBX phone behavior is like parallel line and whoever picks up first will get the call When you reject the call on your mobile phone the unit will send you an SMS with the number of missed ca
4. 2140 CLAMART Copyright 2010 Linkcom All right reserved By pressing the yellow button release the SIM card holder Insert the SIM card and release the SIM card holder Before inserting the SIM card we recommend checking different mobile phone SIM cards settings logging with or without PIN etc and set logging without PIN When you want logging with PIN you have to pre programmed this PIN and set logging with PIN see table of programming Without this setting the Gate wont work DO NOT FORGET ANTENNA CONNECTION To select the place of installation please take into account the following aspects 1 distance from PBX possibility of GSM interferences with other PBX lines as well as length of line from Gate to PBX max 200m 2 main 230 V for power supply of Gate Quality of GSM signal depends on the installation place of GSM Gate Antenna 3 1 Quality of GSM signal The sound quality depends on the BTS setting where you are connected to the Gate To find the best place to mount the antenna you can use either mobile or LED flashing on the unit eventually setting SW in your PC connected via USB port See Manual to set software The suitable signal power is a 3 scale mobile graduation To check and find best position from GSM signal point of view you can use also GG SET configuration SW 3 2 Connection of antenna When you connect magnetic antenna mount it on a big iron subject This subject makes counterweight a
5. are other features which either provide your permanent availability Mobility extension or reduce your phone costs when you are abroad outgoing incoming roaming savings 2 Possibilities of unit installations 2 1 basic connection All calls are terminated over GSM GSM a eu Linkcom France 3 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved EO Foe Y e The unit simulates an ordinary PSTN line with CLIP and call billing When call is established or ended it switches line polarity e Call barring by programming up to 9 permitted 1 to 4 digits prefixes All remaining prefixes are prohibited busy tone e After setting wait for dial to CallBack on a PSTN line when dial O during call back you will transfer the call immediately to connected analog phone or PBX see description of CallBack feature e The Mobility Extension feature works the same way like an ordinary GSM mobile phone call forwarding when you don t accept the call When Phone or PBX connected to the unit is ringing after certain time 3 rings the call is automatically forwarded to preprogrammed GSM mobile number 2 2 Installation between PBX phone and PSTN line Land line calls are terminated via PSTN line and GSM calls via GSM network All incoming calls are routing to connected PBX analog phone wu sa et e In basic setting all outgoing calls are routed to PSTN line In
6. ata transmission by modem The data transmission can not be permanent therefore the unit stays in data mode 10 seconds after finishing data transmission Then it goes back to Voice mode calling The same is when you are calling over unit It is busy for data transmission An optional SW allows the unit for sending and receiving SMS messages is SMS mail It is working Under Outlook Outlook Expres Opera etc And you can work with SMS as with normal e mails see manual for SMS mail It works in batches and allows programming communication interval 1 fo 99 minutes to Link Gate A FXO for sending and receiving SMS Due this we avoid situation that unit is permanently blocked by data mode for voice communication Further functionality of USB is monitoring Link Gate A FXO operation It is also possible to record incoming calls including time and CLIP signal strength etc CAUTION USB is galvanically connected with PSTN and PBX When you use PSTN and USB then is necessary to use galvanically isolated PC for example notebook and power supply in class Il Linkcom France 9 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved 4 Configuration It is possible to access the program mode from a phone connected to the gateway Press the or keys by default then enter the PIN code you will hear the programming tone see table of programming Progress of programming Dial a 2 digit number of t
7. ffecting the power of the radiated signal 3 3 Start 1 Insert SIM card 2 Make sure the cables are correctly connected a phone or trunk line from PBX to the unit b PSTN line or PBX extension to the unit 3 Connect device to power supply 220V a The blue LED power supply lights up within 10 seconds b After couple of seconds a yellow LED will irregularly blink The Gateway is connected to GSM network c The CPU awaits communication with the GSM module see LED table d After 45 seconds the yellow LED starts flashing depending on the GSM reception signal see LED table e When the green LED PBX turns off the Link Gate A FXO Is ready for operation 4 When connected analogue phone is picked up the green LED must turn on and a dial tone will be heard the system is ready to use 3 4 The most often problems during Blue Gate compact installation e None of the LEDs are working Problem with power supply Check connection to main 220V as well as connection of adapter to Link Gate A FXO Linkcom France 8 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved En Q e The LED power supply lights When pick up the earpiece a green LED turns on and you get a busy tone A Yellow LED starts flashing regularly GSM module doesn t communicate with CPU Check that the Link GATE a FXO is not connected to the PC and GGset on USB e The yellow LED flashes regularly PIN unreadable
8. he programming feature dial the parameter number 1 to 4 digits Wait for a tone of confirming request 3 short tones Confirm the feature by pressing Wait for confirming tone Follow by programming tone again Finish programming by hanging up the phone ae oe a Example programming of new permitted fix numbers 02 to memory 09 e Press default is In phone you hear a waiting tone Dial password default 0000 e Waiting tone changes to programming tone Dial 1902 Wait for tone of confirming request 3 short tones e Confirm the feature by dialing Wait for confirming tone one long tone Finish programming mode by hanging up the phone Warning After dialing the parameter number you have to wait for 3 short tones and then dial Wait for long tone that confirms the operation 4 1 Notes to each parameters 11 19 when you program some prefixes the Link Gate A FXO allows outgoing calls starting by those prefixes only The others will get busy tone When memories will be empty the calling won t be restricted default Memory of prefixes can content 1 to 4 digits only Rewriting of memory by storing new fix numbers old fix numbers are erased e Erasing of memory Memory you will erase by storing an empty parameter You dial only the number of the memory which you want to erase and confirm it 22 A very important feature is the character setting Default is but can be change to 24 Analogue p
9. hones are not able to send which is very used in GSM In this case is possible to use combination 00 to send it to mobile phone Parameter 24 allows to activate or deactivate this function A This parameter allows you to look for the best antenna position After activation tones will automatically start to sound and you can scan the strength level of the GSM 31 This feature identifies connection of Link Gate A FXO to external line This is needed for some types of PBX ex Siemens Hicom 32 35 The GSM phones requested command to connection on inserted number The unit will send a command immediately after pressing or after timeout programmed by parameter 32 You can also Linkcom France 10 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved EO Foe Y program number of digits parameter 35 In this case you can dial shorter number Character and timeout are still valid 52 You can program phone numbers of up to 20 digits Calls will be transfer to this number in case of no response on the analogue phone Mobility extension 54 It is possible to program a phone number of up to 20 digits where are periodically 30 days by default adjustable sent SMS messages with unit status IMEI IMSI signal strength BTS number 61 64 4 speed dial memories 20 digit phone numbers They are used when CallBack feature is activated It is Useful to identify more often called n
10. is off No communication on the line Not lighting PSTN port is ON HOOK an light PSTN port is off hook Linkcom France 14 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved KE pis 5 Technical parametres Type Operating position Operating conditions Dimensions mm Part of power supply Supply voltage Power input Protection Safety group Analogue telephopne lines telephone interface telephone conector Impedance Dial Start and end of connection Signalization CLIP PBX Supply conduction Current loop Resistance of subscribers conduction Ringing Billing PSTN DC resistance in ON HOOk Line current Ringing detection GSM mobile network provider USB Linkcom France 11 rue du Soleil Levant 92140 CLAMART Link Gate A FXO various temperature 5 C 40 C humidity 10 80 at 30 C 110 x68 x 27 mm 230 V 10 adapter max 15 VA thermal fuse in adapter CSN EN 60950 group 2 2 wires RJ 11 600 Q 20 tone DTMF t gt 30 ms Polarity reversal 425 Hz 20Hz FSK Bell BT DTMF symetrical 24V max 38 mA max 500 Q 55 Ve 50 Hz 12 16 kHz min 1 MQ 10 65 mA min 20Vrms 25 50 Hz compatible for GSM 900 and GSM 1800 according SIM card 3V and 1 8 V version 1 1 virtual COM 15 Copyright 2010 Linkcom All right reserved
11. ll when it has a CLIP When an incoming call to a GSM unit the call is processed as call forwarding during unavailability of your mobile phone Connected PBX phone starts ringing After 3 rings the call is automatically forwarded to a pre programmed GSM number Linkcom France 5 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved E ASA 2 4 CallBack Callback feature allows you to make a phone call charged to GSM unit account when you are abroad e GSM mobile numbers using this service are saved phone book on the SIM card of the unit e You make a call fo the unit e When unit identifies CLIP the calling number on the saved list it rejects the call and activates the callback feature e When you pick up this call you will hear a CallBack tone see List of tones You have then following options Dial O get access to PSTN line 1 to 4 speed dial memories any other PBX phone or you can wait for pre programmed time to be automatically connected to PBX phone This Callback feature allows you to reduce rapidly your phone costs when you are abroad and make a phone call charged to unit s bill Linkcom France 6 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved Y 3 Installation Yellow button Phone or trunk line from PBX PSIN line extension of PBX Linkcom France 7 11 rue du Soleil Levant 9
12. mber of 1 speed dial memory of Callback n n n Mox 20 digits number of 2 speed dial memory of Call back n n n Mox 20 digits number of 3 speed dial memory of Callback 4 dnin Jn Jn Mox 20 digits number of 4 speed dial memory of Callback _L LL L n n 3 me n O OFF ese UL n E n n n n i nn n Max 20 digits number for mobility extension RER n n n n Linkcom France 092 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved Xx 00 No charging pulses Xx 12 12kHz charging pulses Xx 16 16kHz charging pulses Yy 00 1 pulse only at the moment of connection Yy OT to 99 seconds Pulses each OT up 99 seconds CLIP is switch OFF FSK CLIP Bell FSK CLIP BT DTMF CLIP Eee Hoi ou sll N O Roaming n 0 prohibited n permitted Sending of SMS with CLIP of called party when you reject the call from mobility extension feature 4 In Call progress tone n 0 OFF n 1 ON n 0 restricted n permitted 718 jn Waiting for dial to PSTN line for CallBack el Defour setting Dial tone up setting Mini Gate is ready to accept dial Busy tone short tone repeated Called part is busy doesnt exist not permitted etc Ringing tone long tone and pause repeated Called part is ringing Waiting tone short tone repated with quick cadence Mini Gate waiting for password insert Program
13. ming short tone with quick cadence i Programming mode of Mini Gate Confirmation inquiry 3 short tones Inquiry to confirm inserted parametr Confirmation tone long tone Parametr was saved correcily CallBack tone 1 tone Inquiry to dial dialling in code or dial number of soeed dial Minute tone short tone with 1 minute period Minute beep to inform about GSM c all Call progress tone short tones with different frequency Searching of called part Linkcom France 13 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved vy PS 4 4 LED signalling Permanent light lights up 3 sec after connection of main power GSM modul is powered Permanent light PBX port is OFF HOOK Do not light PBX port is ON HOOK Flashing in rhytm of busy tone Programming mode or PC communication Flashing in 2 sec interval SIM is not readable wrong PIN SIM is not inserted etc Short lights off in period 2 sec GSM modul is not communication with unit CPU 1 5 light flash in period 4 sec stand by mode unit registrated into GSM network number of flashes signal strength 5 max Short light flashing in period 2 sec Unit is not registrated in GSM network The spped flashing with different time period GSM communication is running GSM network registration data communication etc Unregular flashing Voice Communication on the line Permanent light or light
14. ojo fnn fn fn Password nnnn to programming mode access Jo o ojo nfn n fn Memory x for permitted fix number 1 to 4 digits TT TT EEE i alas phn tp fm Pt aP fon Co OOD 211 Jn Reversal polarity n 1 ON ni EE Acknowledge character setting yy n 0 n Type of dial tone n n 0 permanent tone n 1 dial tone up table of tones n 2 dial tone of public lines operator n 3 quiet Turning on combination for dialling to mobile phone n 0 combination turn off n 1 sending to mobile after 00 dialling Signalization to the call short tone each minute n 0 tone is turn off n tone is turn on Restriction of call duration n 0 without restriction n call duration restricted at 10 minutes n PIN n 0 start without PIN n 1 start with PIN 2 n Callback n 0 OFF n 1 ON Ringing after inicialization nn decimal of sec 00 to 99 it is 9 9 sec 00 Not ringing during inicialization njn Waiting for last number nn sec 01 to 15 after finishing of dial by acknowledge character is sending immediately S A Waiting nn sec for dial after pick up 00 to 99 it is 9 9 sec 00 waiting is not limited Number of dialed numeral after its is dial send immediatelly lenght of telephone number nn 00 function none active nn 01 19 number of numeral telephone number n pot CCC EE n n n GSM number for sending controisMS TT n n n Mox 20 digits nu
15. oleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved ea PV 1 Basic features Link Gate A FXO A is dual band GSM Gateway based on the Siemens GSM module TC35i eventually MCS55 equipped with a lot of adjustable features increasing service quality It has been designed for both 900 MHz and 1800 MHz GSM networks e Installing the LinkGate A FXO to your PSTN line will reduce your phone bills GSM calls are routed to GSM network and land line calls are routed to PSTN line e Polarity swap of telephone line allows exact detection of start and end of call e CLIP support all ordinary protocols e CLIP is very important for using other services CallBack Mobility Extension etc e When Identification of PSTN line fails it allows to switch automatically to GSM line back up e Call billing allows exact control of call duration due tax pulses 12 16 kHz 1 pulse when outgoing call is picked Up e Each minute during your call a beep will allow identifying a GSM call e Integrated USB port allows you to easily set it up with PC software as well as sending and receiving SMS messages via SMS mail sw or data transmission Thanks to the Link Gate A FXO features you can satisfy a wide group of customers Adding allowed numbers to the Link Gate A FXO memory you can restrict unwanted calls public numbers You can also program the Link Gate A FXO to provide incoming calls only The CallBack and Mobility Extension
16. umbers They are activated by dial 1 2 3 4 77 Blocking of SMS sending to number preprogrammed in parameter 52 This SMS with phone number of calling party is send in case that phone call through mobility extension feature wasn t picked up 78 After timeout without dialing any code to access PSTN line 0 or speed dial 1 to 4 the call is automatically forwarded to PBX phone port which starts ringing 79 The unit detects the current on PSTN line 100ms after pick up This feature provide automatic routing to GSM network in case of PSTN line failure When the current starts slowly on PSTN line less then 100ms the detection cant work and PSTN line is evaluated as failed When you don t want use this feature please do not use the PSTN line detection Caution When you use GSM only without PSTN connection the PSTN line detection must be activated Notes e Programming is only by tone dial DTMF Don t forget set even external line at PBX e Changes are valid after hanging up only finishing of programming mode e After entering the programming numbers if is important to wait for the confirmation tone 3 short beeps if numbers are entered to early the programming wont e Switch to programming mode is possible even on busy tone Linkcom France 1 11 rue du Soleil Levant 92140 CLAMART Copyright 2010 Linkcom All right reserved ut a no ae FET 4 2 Table of programming Dial number _ Feature Defauit
Download Pdf Manuals
Related Search