OPS883-H User`s Manual VA1
Contents
1. DRAM Install Step 1 Loosen the screws on the real of chassis as illustrated J 16 Hardware Installation OPS883 User s Manual Step 3 Place the memory module into the socket and press it firmly The socket latches are levered upwards and clipped on to the edges of the DIMM d 2 5 HDD SSD Instllation The OPS883 series provides one 2 5 SATA HDD tray to install 2 5 HDD When please refer to the following instructions and illustration Step 1 Loosen the screws per illustrated Step 2 Please refer to the below photo to connect the target 2 5 HDD SSD with HDD s bracket Hardware Installation 17 OPS883 User s Manual Step 3 Then plug HDD drive in to HDD connector Mini PCle Module Installation The OPS883 series provides one Mini card slot for user to install mini cards please refer to the following instructions and illustration Step 1 Loosen the screws per illustrated 18 Hardware Installation OPS883 User s Manual Step 2 Then open the cover carefully SEN E Step 3 You can find the position of Mini PCIe slot and please insert it then fasten screw of Mini PCle module by yourself Soe Hardware Installation 19 OPS883 User s Manual SIM Card amp Antenna Cable Installation Step 1 Install SIM Card module Place the SIM Card module into the socket and press it firmly down until it is fully located Step 2 The following photos2. dd AXIOMTEK OPS883 Series Intel Open Pluggable Specification Box User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information Axiomtek Co Ltd assumes no responsibility for any infringements of patents or any third party s rights and any liability arising from such use Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of any information in this document Axiomtek does not make any commitment to update the information in this manual Axiomtek reserves the right to change or revise this document and or product at any time without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Axiomtek Co Ltd Copyright 2015 Axiomtek Co Ltd All Rights Reserved November 2015 Version A1 Printed in Taiwan Safety Approvals CE Marking E FCC Class A FCC Compliance This equipment has been tested in compliance with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are mean to provide reasonable protection against harmful interference in a residential installation If not installed and used in accordance with proper instructions this equipment might generate or radiate radio frequency
3. Inc SST is a trademark of Silicon Storage Technology Inc UMC is a trademark of United Microelectronics Corporation Other brand names and trademarks are the properties and registered brands of their respective owners Table of Contents Met UE fostrets de sars Ndi nde se SR en S SNR GR Rd il Safety AD DOV EE iii Sare ly TE d EE iv CHAPTER 1 INTRODUCTION WEE 1 1 1 General DESCIHP Ul OM WE 1 1 2 System Specifications sssssssssssssrsssssnnssnnsnnn nnn nns nn ARR ARR RAR RR A RR RARE Ra 2 Lk Mait CPU BOGICO eege 2 122 WO SY SUSI E 2 1 3 Mechanical ASSCMD TE 4 o1 DiMenSiONS zuppa a eeuseseaaneelt 4 t32 JEGEN 5 1 3 3 Mechanical Specifications siscicccccesicccscecedsscweoscdetevcecesswesiccccaeesiacewesielidececdorexeseen 6 134 Reference eege ge eege deen ee ENEE dee ege 11 1 4 PACKAGE EIS EE 12 CHAPTER 2 HARDWARE INSTALLATION 13 2 1 CPU Storage DRAM Wireless amp 3G module Installations 13 2 2 Pluggble Module Method ssccssseceseceeseceneeeseeeeseeeseeeeseseasenenes 21 CHAPTER 3 CONNEC TORS vassoio ar sissi eldens 23 3 1 CONN EC de 23 3 1 1 JAE TX25 Connector CNI gege 25 512 OPUFAN CNJ nn tet ee ea ete ar 26 31 3 SIM Card SIOt CNA E 26 3 1 4 HME GD Eet 27 3 1 5 Power 8 Reset Button CNG ssss ss ss ssssss rssarsnssnnnannnnrnnn nnA RAR AREAN ARR A RAR 27 3 1 6 Audio MIC IN Connector SCN2 s
4. ssssssssssssssssssssssnsasrnnnnnnrnnnnn r nnan AA ARR ARR 28 3 1 7 AudioLine Out Connector SCN3 ssss s sssssssssnssrsrnnrrennnnnnn nn nn nn nn nn 28 3 1 8 Battery 2 PIN BAT1 c cccsssscecessssecesesesseceseeseseseseesesesessseseserarseseseraeeesesaees 28 3 1 9 Mini Card Slot SCHT 29 S110 SSW En d re DE 30 3 1 11 SATA amp SATA Power Connector SATA1 ccccccssssseeesseeesseeeseeensseeeseoenes 31 3 1 12 RJ45 1217LM LAN 32 3 1 13 USB 3 0 Port SUSB1 sssssusssssssessssnsnsornensnenrnen sne rna rann rann rann rn rn 2 rn 222 20 32 2 114 USB Eort e Ee 33 3 1 15 COM Port COM 33 CHAPTER A AMI BIOS SETUP UTILITY bsbosssssssorssoosssorssorsssorssorrssernsernrsnrrserrsnrrrn 35 4 1 SL T UNO EE 35 4 2 INAVIGAtION KeySonic tice demens sn tien neta dees t rn L den tnak 35 4 3 OU lg IMGT sissen pe 36 4 4 POV ANCE Wd E UR 37 4 5 RID SET dE EE 47 4 6 B OOU MENU oss cots ee Ee 53 4 7 Se CUNY lead 54 4 8 DAVE Q EX MENU aia 55 APPENDIX A REFERENCE DOCUMENTS 3isssssossssoosssoorsssoressorsrsosrssesrsnssrsrnssrnrssrs 57 APPENDIX B WATCHDOG TIMER eege 59 APPENDIX C IAMT EELER ee 60 vi OPS883 User s Manual CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the OPS883 series Chapter 1 includes the following sections General Description Specification Michanical Assembly Package List 1 1 General Description Intel Open Plug
5. O 2F 07 3 WDT Device Enable O 2E 2B O 2F 00 O 2E 30 O 2F 01 4 Activate WDT O 2E FO O 2F 80 5 Set base timer O 2E F6 O 2F 0A gt Set Reset Time Ex A 10 Sec 6 Set timer unit O 2E F5 O 2F 71 1 Sec 9 Minute 7 Disable WDT O 2E 30 O 2F 00 Watchdog Timer 59 Appendix C IAMT Settings The Intel Active Management Technology Intel IAMT has decreased a major barrier to IT efficiency that uses built in platform capabilities and popular third party management and security applications to allow IT a better discovering healing and protection their networked computing assets In order to utilize Intel iAMT you must enter the ME BIOS lt Ctrl P gt during system startup change the ME BIOS password and then select Intel iAMT as the manageability feature C 1 Entering MEBx 1 Goto BIOS to enable iAMT function see section 4 4 2 Exit from BIOS after starting iAMT and press lt Ctrl P gt to enter MEBx Setting Ki It is better to press lt Ctrl Ps before the screen popping out Note C 2 Set and Change Password 1 You will be asked to set a password when first log in The default password is admin Intel R Management Engine BIOS Extension v9 0 0 0024 Intel R ME v9 0 1 1333 copyright c 2003 12 Intel Corporation Al Rights Reserved MAIN MENU MEBx Login gt Intel tk ni ME General Settings gt Intel R AMT Configuration MEBx Exit Intel R ME Passw
6. Setup options if your computer is experiencing system configuration problems Select Restore Defaults from the save amp Exit menu and press lt Enter gt Save as User Defaults Select this option to save system configuration changes done so far as User Defaults Select Save as User Defaults from the Save amp Exit menu and press lt Enter gt Restore User Defaults It automatically sets all Setup options to a complete set of User Defaults when you select this option Select Restore User Defaults from the Save amp Exit menu and press lt Enter gt AMI BIOS Setup Utility OPS883 User s Manual APPENDIX A REFERENCE DOCUMENTS Document No Location Digital Signage Open Pluggable Specification 324427 JAE TX24 TX25 connector product brief SS 4T JAE plug connector details and drawing EN com en product_en cfm code E roduct number JAE receptacle connector details and drawing Reference Documents 57 OPS883 User s Manual This page is intentionally left blank 58 Reference Documents OPS883 User s Manual APPENDIX B WATCHDOG TIMER Watchdog Timer Setting After the system stops working for a while it can be auto reset by the Watchdog Timer The integrated Watchdog Timer can be set up in the system reset mode by program Using the Watchdog Function Start 1 Enable configuration Following is example to enable configuration by using debug O 2E 87 O 2E 87 2 Select Logic device O 2E 07
7. and press lt Enter gt Select Yes to discard changes and exit BIOS Setup gt Save Changes and Reset When you have completed the system configuration changes select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect Select Save Changes and Reset from the Save amp Exit menu and press lt Enter gt Select Yes to save changes and reset AMI BIOS Setup Utility 55 OPS883 User s Manual 56 Discard Changes and Reset Select this option to quit Setup without making any permanent changes to the system configuration and reboot the computer Select Discard Changes and Reset from the Save amp Exit menu and press lt Enter gt Select Yes to discard changes and reset Save Changes When you have completed the system configuration changes select this option to save changes Select Save Changes from the Save amp Exit menu and press lt Enter gt Select Yes to save changes Discard Changes Select this option to quit Setup without making any permanent changes to the system configuration Select Discard Changes from the Save amp Exit menu and press lt Enter gt Select Yes to discard changes Restore Defaults It automatically sets all Setup options to a complete set of default settings when you select this option The Optimal settings are designed for maximum system performance but may not work best for all computer applications In particular do not use the Optimal
8. energy and cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following methods Increase the separation between the equipment and receiver B Connect the equipment to another outlet of a circuit that does not connect with the receiver C Consult the dealer or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with the emission limits Safety Precautions Before getting started please read the following important safety precautions 1 10 The OPS883 series does not come equipped with an operating system An operating system must be loaded first before installing any software into the computer Be sure to ground yourself to prevent static charge when installing the internal components Use a grounding wrist strap and place all electronic components in any static shielded devices Most electronic components are sensitive to static electrical charge Disconnect the power cord from the OPS888 series before any installation Be sure both the system and external devices turned OFF already Make sure the OPS883 series set to ground properly The brightness of the fla
9. exit the setup without saving your changes The lt Enter gt key allows you to display or change the setup option listed for a particular setup item The lt Enter gt key can also allow you to display the setup sub screens The lt Esc gt key allows you to discard any changes you have made and exit the Setup Press the AMI BIOS Setup Utility 35 OPS883 User s Manual 4 3 Main Menu When you first enter the Setup Utility you will enter the Main setup screen You can always return to the Main setup screen by selecting the Main tab There are two Main Setup options They are described in this section The Main BIOS Setup screen is shown below e BIOS Information Aptio Setup Utility Copyright C 2012 American Megatrends Inc Advanced Chipset Boot Security Save amp Exit System Language English Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt System Date Time Use this option to change the system date and time Highlight System Date or System Time using the lt Arrow gt keys Enter new values through the keyboard Press the lt Tab gt key or the lt Enter gt keys to move between fields The date must be entered in MM DD YY format The time is entered in HH MM SS format 36 AMI BIOS Setup Utility OPS883 User s Manual 4 4 Advanced Menu The Advanced menu also allows users to set configuration of the CPU and other system devices You can select any of the items in the left frame
10. show you how to connect antenna cable by yourself SS Kips x Maa ZE e EK AN WS D 20 Hardware Installation OPS883 User s Manual 2 2 Pluggble Module Method LY Y NOTE Please contact Axiomtek for the available option display Step 1 Pluggable the box into display Caution When plugging OPS883 series module into an OPS display make sure the module s heat sink is facing outside of the display Axiomtek is not responsible for any damage caused by wrong installation Step 2 Fasten the screws as illustrated HDMI d d Hardware Installation 21 OPS883 User s Manual This page is intentionally left blank 22 Hardware Installation OPS883 User s Manual CHAPTER 3 CONNECTORS This chapter provides users with detailed description how to set up basic system configuration through the AMIBIOS8 BIOS setup utility 3 1 Connectors Connectors connect this board with other parts of the system Loose or improper connection might cause problems Make sure all connectors are properly connected Here is a Summary table shows you all connectors on the board Connector JAE TX25 Connector POWER amp RESET BUTTON Audio MIC IN Connector Audio LINE OUT Connector Mini Card Slot Battery 2 PIN ATX Auto Power On Clear CMOS PCle Signal Switch Reserve SLP_S3 Docking Support SATA amp SATA Power Connector 5V Only RJ45 1217LM U
11. to set up basic system configuration through the AMIBIOS8 BIOS setup utility 4 1 Starting To enter the setup screens follow the steps below gt Turn on the computer and press the lt Del gt key immediately gt After you press the lt Del gt key the main BIOS setup menu displays You can access the other setup screens from the main BIOS setup menu such as the Chipset and Power menus 4 2 Navigation Keys The BIOS setup utility uses a key based navigation system called hot keys Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process These keys include lt F1 gt lt F2 gt lt Enter gt lt ESC gt lt Arrow gt keys and so on DCH SS NOTE Some of navigation keys differ from one screen to another lt Left Right The Left lt Arrow gt keys allow you to select a setup screen AW Up Down The Up and Down lt Arrow gt keys allow you to select a setup screen or Sub screen a The Plus and Minus lt Arrow gt keys allow you to change the field value Plus Minus i of a particular setup item The lt Tab gt key allows you to select setup fields The lt F1 gt key allows you to display the General Help screen The lt F2 gt key allows you to Load Previous Values The lt F3 gt key allows you to Load Optimized Defaults The lt F4 gt key allows you to save any changes you have made and exit Setup Press the lt F4 gt key to save your changes lt Esc gt key to
12. 00000000000000000 0000000000000000000000000000000000000000000 ro 0O0000000000000 ODOoOoOoOooooOooooOo OO oo 0000000000000000000000000000000000000000000 0o0o000000000000000000000000000000000000000000 0000000000000000000000000000000000000000000 0000000000000000000000000000000000000000000 000000000000000 AAAAAAAAA 0o0o00000000000000 ee ee E EEN RE E A Mb ooooo0o0o00000000 000000000000000 The digital signage OPS883 series prototype is based on a 32 display panel with the functional blocks illustrated It is mainly a 3 board partitioning design consisting of the pluggable module docking board and the panel control board 11 Introduction OPS883 User s Manual 1 4 Package List When you receive the OPS883 series the bundled package should contain the following items e OPS883 System x 1 e CDx1 e THERMAL GREASE Syringe 1G e M2x5screw x 2 e M4x6screw x2 If you cannot find the package or any items are missing please contact Axiomtek distributors immediately 12 Introduction OPS883 User s Manual CHAPTER 2 HARDWARE INSTALLATION The OPS883 series is convenient for your various hardware configurations such as Storage Memory Module The chapter 2 will show you how to install the hardware It includes CPU HDD DRAM Wireless amp 3G module Installation Pluggable Module Method 2 1 CPU Storage DRAM Wireless amp 3G module Installations The
13. 55 255 255 0 255 255 2355 0 lt Enter gt Complete Entry Esc Discard Changes 4 Go back to Intel iAMT Configuration then select Activate Network Access and press lt Enter gt Intel R Management Engine BIOS Extension v9 0 0 0024 Intel R ME v9 0 1 1333 Copyright c 2003 12 Intel Corporation All Rights Reserved INTEL R AMT CONFIGURATION Manageability Feature Selection lt Enabled gt SOL IDER KVM user Consent Password Policy z nytimer Network Setup Activate Network Access Unconfigure Network Access Remote Setup And Configurati Power contral Activates the current network settings and opens the ME network interface Continue CYAN lt Move Highlight Enter Select Entry 5 Exit from MEBx after completing the iAMT settings 64 Watchdog Timer OPS883 User s Manual CA iAMT Web Console 1 From a web browser please type http IP ADDRESS 16992 which connects to iAMT Web Example http 10 1 40 214 16992 g gt hd http 10 1 40 214 16992 logon htm iM 9 gt x lt Pi we abe nee Active Management Technology Ei amp R m GIRO Intel Active Management Technology Log On Log on to Intel Active Management Technology on this computer Log On Q SH 100 2 To log on you will be required to type in username and password for access to the Web USER admin default value PASS MEBx password Watchdog Timer 65 OPS883
14. 68 CH a 2 KD Le H an mm on am x While plugging the OPS module please make sure the heat sink side of OPS module toward the outside Axiomtek will be out of reasonability if there is any damage occurred due to it 4 Introduction OPS883 User s Manual 1 3 2 I O outlet The following figures show you the locations of the OPS888 series I O outlets No Connector No Connector oa os Le ingicator 2 Antennaopening o Audio tineout ps ses o otemt pa Ehomt Lmn luesen s mmo ua e Some geg 13 Antenna opening z eset ft 25 SATA HDD tray Introduction 9 OPS883 User s Manual 1 3 3 Mechanical Specifications OPS883 series is docked in the reference display panel The OPS883 Pluggable Module docked at a display panel system In this reference design the module is docked and undocked in the vertical direction Y AY NOTE Please contact Axiomtek for available option display panel 6 Introduction Exploded View of the Pluggable Module OPS883 User s Manual The Guide Rail Mechanism for the OPS883 series Module You can use the rails alongside of OPS883 series Module to dock and undock the plug connector at the back of the module to connect with docking board There are two lock pins on each side of the rail and they serve as the locking mechanism to attach the lock holes on the series module Geer del oa sa sa 8 FRONT VIEW BACK VI
15. EW Introduction Lock Hole Plug connector Lock Pin OPS883 User s Manual Location of Lock Hole on the Pluggable Module Lock Hole Lock Pin FRONT VIEW BACK VIEW The drawing is base on Intel Open Pluggable Specification 8 Introduction OPS883 User s Manual Dimensions of the Guide Rail 116 Introduction J OPS883 User s Manual Location of JAE TX25 Plug Connector Please refer to the following drawing for location of the JAE TX25 plug connecior Pin 1 of the connector is located at 114 8 mm from the edge of the module and 106 9 mm from the inner side of the front panel For mating tolerance of TX25 plug connector and TX24 receptacle connecior please refer to the JAE specification PCB Location SEA SECTION AA AA Vent Holes at the Pluggable Module Back Panel On the OPS883 series module it is recommended by Intel that some vent holes be opened at the back so that hot air can escape more easily from the module that the FAR in on both sides of the module back panel should be greater than 0 25 D Galle area 20 2 26mm FAR gt 0 25 10 Introduction OPS883 User s Manual Reference Design 1 3 4 Display Panel Rear View Internal GC900000000 00 00 0 0 tr T TT TU o00000000000000 0000000000000000000000000000000000000000000 0o000000000000000000000000000000000000000000 00000000000000000000000000
16. Manual 4 7 Security Menu The Security menu allows users to change the security settings for the system Aptio Setup Utility Copyright C 2012 American Megatrends Inc Main Advanced Chipset Boot Save amp Exit Administrator Password Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt Administrator Password This item indicates whether an administrator password has been set If the Administrator password is set BIOS will ask and wait for administrator password entered gt User Password This item indicates whether a user password has been set If the password is set BIOS will ask and wait for User password entered 54 AMI BIOS Setup Utility OPS883 User s Manual 48 Save amp Exit Menu The Save amp Exit menu allows users to load your system configuration with optimal or failsafe default values Aptio Setup Utility Copyright C 2012 American Megatrends Inc Main Advanced Chipset Boot Security Save Changes and Exit Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt Save Changes and Exit When you have completed the system configuration changes select Save Changes and Exit from the Save amp Exit menu and press lt Enter gt Select Yes to save changes and exit BIOS Setup gt Discard Changes and Exit This option provide quit Setup without making any permanent changes to the system configurationSelect Discard Changes and Exit from the Save amp Exit menu
17. ND RVD4 3 3VAUX GND PERST PERNO 3 3VAUX PERPO GND GND 1 5V GND SMB_CLK PETNO SMB DATA PETPO GND GND USB D RVD5 USB D 3 3VAUX GND 3 3VAUX LED WANS RVD8 LED WANS RVD9 LED _WPAN RVD10 1 5V RVD11 GND RVD12 3 3VAUX NH1 Drivers Installation 29 OPS883 User s Manual 3 1 10 SSW1 Setting ATX AT Mode Setting Clear CMOS SLP_S3_ Docking SSW1 Pin8 AT or ATX Select SSW1 Pin1 Description Settings OFF Deal Clear CMOS SSW1 Pin2 Description settings Clear CMOS OFF Default PCIe Signal Switch SSW1 Pin3 Description settings OFF Deal MSATA SLP_S3_Docking SSW1 Pin4 Deseription settings SLP_S3 30 O FO LAR le wo IK a Drivers Installation OPS883 User s Manual 3 1 11 SATA amp SATA Power Connector SATA1 GND SATAO_TX SATAO_TX GND SATAO_RX SATAO_RX GND S1 S7 P1 P15 IO UDITO CH 8 Drivers Installation 31 OPS883 User s Manual 3 1 12 RJ45 1217LM LAN1 The RJ 45 connector LAN1 is for Ethernet To connect the board to 100 Base T or 1000 Base T hub just plug one end of the cable into LAN1 and connect the other end phone jack to a 100 Base T hub or 1000 Base T hub e
18. OPS883 series model offers a convenient drive bay module for users to install CPU Storage DRAM wireless amp 3G modules Please follow the steps CPU Installation Step 1 Turn off the system Loosen the screws as illustrated zazsotva KC VAN au Sara 3 G Hardware Installation 13 OPS883 User s Manual Step 3 Refer to the following photo to loosen the screws and pillars in advance wy NOTE Please pull out power cable of system fan while installation Step 4 Then turn over the chassis as per illustrated Ed NOTE Please be aware of the CPU FAN Cable while installing the CPU you do not need to pull out the cable to avoid cable damage 14 Hardware Installation OPS883 User s Manual Step 5 Remove the CPU waring mylar and then pull out the desktop CPU socket pole pg PEPEE art Ger eae Pee eee 2 See RR peat pg en VAS gege Dt Deeg i a teenie PEN ELSE ASN ew WANS AAR AAA AA AAA ses van AAA RAR tn de ted tea aan SAA bd tented ttn tnt n PAR Lettre dames ae a IKEA E TIRARA Dm 4 s ws Insert the CPU into the slot Please follow the indication on CPU as mark and slot to ensure the proper insertion of the CPU Step 6 Step 7 Please make sure CPU has inserted into the socket and the latch is closed 15 Hardware Installation OPS883 User s Manual Step 8 Press pole of the CPU socket firmly as per illustrated
19. Primary IGFX Boot Display Select the video device which will be activated during POST It has no effect if external graphics presents VGA modes will be supported only on primary display AMI BIOS Setup Utility 51 OPS883 User s Manual e Memory Information Memory configuration parameters Aptio Setup Utility Copyright C 2012 American Megatrends Inc Not Present Max TOLUD Dynamic Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt Max TOLUD This item allows you to set Maximum Value of TOLUD 52 AMI BIOS Setup Utility OPS883 User s Manual 4 6 Boot Menu The Boot menu allows users to change boot options of the system You can select any of the items in the left frame of the screen to go to the sub menus e Setup Prompt Timeout e Boot up Num Lock State e Quiet Boot e Boot Option Priorities Aptio Setup Utility Copyright C 2012 American Megatrends Inc Main Advanced Chipset Boot Security Save 8 Exit Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt Setup Prompt Timeout Set the number of seconds to wait for Setup activation key gt Boot up Mum Lock State Use this item to select the power on state for the Mum Lock The default setting is on gt Quiet Boot Use this item to enable or disable the Quite Boot state The default setting is disabling gt Boot Option Priorities Sets the system boot order AMI BIOS Setup Utility 53 OPS883 User s
20. SB3 0 Port 1 USB2 0 Port 2 USB2 0 Port 3 Power LED Drivers Installation 23 OPS883 User s Manual Board Layout CPU Socket Top side un C m o kel V Bottom side 24 Drivers Installation 3 1 1 JAE TX25 Connector CN1 Connector JAE TX25 CN1 is for JAE interface support DDP_3N DDP_3P OPS883 User s Manual DDP_2P GND GND DDP_ON DDP_AUXN DDP_AUXP DDP_HPD TMDS_CLK TMDS_CLK GND TMDSO GND TMDS1 GND TMDS2 TMDS2 DVI_DDC_DATA DVI_DDC_CLK DVI HPD 12V 19V 12V 19V 12V 19V 12V 19V 12V 19V 12V 19V 12V 19V 12V 19V RSVD RSVD RSVD RSVD RSVD RSVD RSVD RSVD SLP_S3 SYS_FAN UART_RXD UART_TXD GND StdA_SSRX StdA_SSRX GND StdA_SSTX StdA_SSTX GND USB_PN2 USB _PP2 GND USB_PN1 USB PPt GND USB_PNO USB_PPO GND AZ_LINEOUT_L AZ_LINEOUT_R NC PB DET PS ONS PWR STATUS GND GND 109340 20 SZXL ua aperdarag pr Drivers Installation GND d MaA dl 25 OPS883 User s Manual 3 1 2 CPU FAN CN2 CN2 provides power input and FAN control signal and you can connect CPU FAN through this connector 3 1 3 SIM Card Slot CN4 This slot supports inserting SIM Card In order to work properly the SIM Car
21. USB device under legacy OS such DOS when choosing AUTO the system will automatically detect any USB device is plugged into the computer and enable USB legacy mode During a USB device plugged and disable USB legacy mode the USB device will not available in legacy O S 44 AMI BIOS Setup Utility OPS883 User s Manual e F81801 Super IO Configuration Set parameters of Serial Port 1 COM1 Serial Port 2 COM2 Aptio Setup Utility Copyright C 2012 American Megatrends Inc gt Serial Port 1 Configuration Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt Serial Port Enable or Disable serial port gt Device Settings Display the serial port resource AMI BIOS Setup Utility 45 OPS883 User s Manual e PC Health Status This screen shows the Hardware Health Configuration and enable or disable smart fan Aptio Setup Utility Copyright C 2012 American Megatrends Inc Smart Fan Function Enabled Smart Fan Function DIET lo Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc 46 AMI BIOS Setup Utility OPS883 User s Manual 4 5 Chipset Menu The Chipset menu allows users to change the advanced chipset settings You can select any of the items in the left frame of the screen to go to the sub menus e PCH IO Configuration e System Agent SA Configuration Aptio Setup Utility Copyright C 2012 American Megatrends Inc Fr PCH IO Configuration Versio
22. User s Manual 3 Enter the iIAMT Web BEI EJ intel Standard Manageability Computer System Status System Status Copyright 2003 2012 Intel Corporation All Rights Reserved Intel Standard Manageability firmware version 9 0 3 bulid 1347 Remote Control 5 When you have finished using the iAMT Web console close the Web browser 66 Watchdog Timer OPS883 User s Manual This page is intentionally left blank Watchdog Timer 67
23. ch Tx Data transmission positive Tx Data transmission negative Rx Data reception positive RJ 1 For 1000 base T Only RJ 1 For 1000 base T Only Rx Data reception negative RJ 1 For 1000 base T Only RJ 1 For 1000 base T Only Active LED Speed LED D gt Io IN IO SJOA IA W Pp 3 1 13 USB 3 0 Port SUSB1 USB3_POWER USB DO USB DO GND USB3_SSRX0 USB3_SSRX0 GND USB3_ SSTX0 USB3_ SSTX0 32 Drivers Installation OPS883 User s Manual 3 1 14 USB 2 0 Port SUSB2 3 USB_POWER USB DO f Ni ol SI USB DO GND 3 1 15 COM Port COM2 The COM Port connector is a standard DB 9 connector The pin assignment of RS 232 is listed on the following table Pin soa 8 DSR Data set ready RTS Request to send 8 crs cieartosend 9 RI Ring indicator Power LED The Power LED lights up when the system is powered ON HDD Activity LED This connection is linked to hard drive activity LED on the control panel LED flashes when HDD is being accessed Drivers Installation 33 OPS883 User s Manual This page is intentionally left blank 34 Drivers Installation OPS883 User s Manual CHAPTER 4 AMI BIOS SETUP UTILITY This chapter provides users with detailed description how
24. d must be used together with 3G module It s mainly used in 3G wireless network application 26 Drivers Installation OPS883 User s Manual 3 1 4 HDMI Connector CN5 The HDMI High Definition Multimedia Interface is a compact digital interface which is capable of transmitting high definition video and high resolution audio over a single cable HDMI r GND OUT DATA2 SSES CH 5 HDMI 4 HDMI TETTETETT OUT DATA2 OUT DATA1 HDMI s jen Ir OUT DATA1 7 HDMI GND OUT DATAO HDMI HDMI OUT Clock OUT DATAO o Tan 12 Oe 3 1 5 Power amp Reset Button CN6 CNG is the reset switch that reboots your computer instead of turning OFF the power switch It is a better way to reboot your system for a longer life of the system s power supply Power Button Drivers Installation 21 OPS883 User s Manual 3 1 6 Audio MIC IN Connector SCN2 Tee See Lessel Eh LINE_OUT_L LINE_OUT_R LINE OUT DETECT GND 28 Drivers Installation 3 1 9 Mini Card Slot SCN1 This is a PCI Express Mini Card connector which supports PCI Express x1 link USB 2 0 link and 3G LTE wireless network application OPS883 User s Manual SCN1 also supports SATA signal for mSATA device users can adjust it to SATA mode through BIOS configuration WAKE 3 3VAUX RVD1 GND RVD2 1 5V CLKREQ RVD19 GND RVD18 REFCLK RVD16 REFCLK RVD15 GND RVD14 RVD3 G
25. e CPU LGA1150 socket type A generation Intel Core i5 i3 Celeron Processor e System Chipset m Intel Q87 PCH e BIOS American Megatrends Inc UEFI Unified Extensible Firmware Interface BIOS e System Memory One socket 204 pin DDR3 1333 1600MHz SO DIMM maximun up to 8GB e Wireless Module Optional x Optional IEEE802 11 b g n Bluetooth 2 0 1 2 2 I O System e Standard I O One HDMI with 4K solution Two USB ports 2 0 m One USB ports 3 0 m One RS 232 COM2 m One Power on Off button One Reset button Ethernet m 10 100 1000Mbps Ethernet with Intel 1217 Audio m Line out Mic in e Expansion m One Full size PCI Express Mini card USB PCle signals supported e Storage mum One 2 5 SATA HDD tray m One mSATA option through Mini PCIe by SSW1 selection e Net Weight m 0 9Kg 1 99 Ib without cooler 2 Introduction OPS883 User s Manual e Dimension Main Body Size m 200 mm W x 119 mm D x 30 mm H e Operation Temperature m OC to 45C with airflow 1 2 m s Sy FY NOTE All specifications and images are subject to change without notice Introduction 3 OPS883 User s Manual 1 3 Mechanical Assembly 1 3 1 Dimensions This diagram shows you dimensions and outlines of the OPS888 series The overall dimension of the module including the mounting frame is 200mm x 119mm x 30mm and it shows the location of the screw holes of front panel as well as the security lock 00 3909066
26. escription of the selected item appears on the right side of the screen Aptio Setup Utility Copyright C 2012 American Megatrends Inc SATA Controller s Enabled SATA Controller s Enabled Disabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt Serial ATA Controller S Use this item to enable or disable the integrated SATA controllers Default Enabled gt Serial ATA Port 1 Enable or Disable SATA Port 42 AMI BIOS Setup Utility OPS883 User s Manual e PCH FW Configuration You can use this screen to confirm ME Firmware version Aptio Setup Utility Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc e AMT Configuration Enable Disable Intel R Active Management Technology BIOS extension Aptio Setup Utility Copyright C 2012 American Megatrends Inc Intel AMT Disabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc AMI BIOS Setup Utility 43 OPS883 User s Manual e USB Configuration You can use this screen to select options for the USB Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen Aptio Setup Utility Copyright C 2012 American Megatrends Inc Legacy USB Support Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt Legacy USB Support This is for supporting
27. gable Specification OPS Compliance OPS883 series is based on the 4 generation Intel Core processor on board with Intel Q87 Express Chipset platform and it also future products The Pluggable Module is dedicated to provide an interchangeable solution to the digital signage media players with compatible connector This document provides the module form factor connector specification reference thermal solution and boundary conditions in order to ensure the functionally of the module in all compatible display panel system OPS883 series meets Intel Open Pluggable Specification for design and development simplifying system upgrade maintenance for manufacturers and developers that supports Intel 4 Generation Core series family which stand for high flexible and user friendly digital signage applications Easy maintenance OPS883 series offers a best solution for digital signage market Compliant with Intel OPS architecture digital signage players are capable of deploying interchangeable systems faster and easing upgrading maintenance while lowering costs for development and implementation Additionally having the ability to simply slot in and out the unique pluggable engine box makes daily hassle easier and faster for users OPS883 series has pluggable engine box design you can change storage DRAM and update configurations more easily Introduction 1 OPS883 User s Manual 1 2 System Specifications 1 2 1 Main CPU Board
28. n 2 15 1236 Copyright C 2012 American Megatrends Inc AMI BIOS Setup Utility 47 OPS883 User s Manual e PCH IO Configuration PCH Azalia Configuration settings Aptio Setup Utility Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc 48 AMI BIOS Setup Utility OPS883 User s Manual e PCH Azalia Configuration Contorl Detection of the Azalia device Aptio Setup Utility Copyright C 2012 American Megatrends Inc Enabled Azalia Disabled enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt Azalia Enable or disable Azalia device AMI BIOS Setup Utility 49 OPS883 User s Manual e System Agent SA Configuration To adjust graphics and memory detail configurations Aptio Setup Utility Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt Graphics Configuration Configure graphics settings gt Memory Information Memory configuration parameters 50 AMI BIOS Setup Utility OPS883 User s Manual e Graphics Configuration Select the Video Device which will be activated druing POST This has no effect if external grpahis present Aptio Setup Utility Copyright C 2012 American Megatrends Inc Primary IGFX Boot Display Auto Primary IGFX Boot Display AUTO Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt
29. of the screen to go to the sub menus gt ACPI Settings S5 RTC Wake Settings Trusted Computing CPU Configuration SATA Configuration PCH FW Configuration AMT Configuration USB Configuration F81801 Super IO Configuration F81801 H W Monitor VV VV VV VV WV For items marked with b please press lt Enter gt for more options Aptio Setup Utility Copyright C 2011 American Megatrends Inc WETT Chipset Boot Security Save amp Exit ACPI Settings Version 2 14 1219 Copyright C 2011 American Megatrends Inc AMI BIOS Setup Utility 37 OPS883 User s Manual e ACPI Settings You can use this screen to select options for the ACPI Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen Aptio Setup Utility Copyright C 2012 American Megatrends Inc ACPI Sleep State S3 only Suspend to ACPI Sleep State 53 Only Suspend to RAM Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt ACPI Sleep State Allow you to select the Advanced Configuration and Power Interface ACPI state to be used for system suspend Here are the options for your selection S3 Suspend to RAM 38 AMI BIOS Setup Utility OPS883 User s Manual e S5RTC Wake Settings Enable or disable system wake on alarm event When enabled System will wake on the hr min sec specified Aptio Setup Utility Copyright C 2012 American Mega
30. ord 1t Move Highlight Enter Select Entry Esc Exit 60 Watchdog Timer OPS883 User s Manual 2 You will be asked to change the password before setting ME Intel R Management Engine BIOS Extension v9 0 0 0024 Intel R ME v9 0 1 1333 Copyright c 2003 12 Intel Corporation All Rights Reserved MAIN MENU MEBx Login gt Intel R ME General Settings gt Intel R AMT Configuration MEBX Exit Intel R ME Password Intel R ME Password lt Move Highlight Enter Select Entry Esc Exit 3 You must confirm your new password while revising The new password must contain example 11qqQQ default value e Eight characters e One upper case e One lower case e One number e One special symbol suchas gt or gt excepted Underline _ and space are valid characters for password but they won t make higher complexity Watchdog Timer 61 OPS883 User s Manual C 3 iAMT Settings Select Intel iAMT configuration and press lt Enter gt Intel R Management Engine BIOS Extension v9 0 0 0024 Intel R ME v9 0 1 1333 Copyright c 2003 12 Intel Corporation All Rights Reserved MAIN MENU it Move Highlight Enter Select Entry Esc Exit 1 Select Network Setup to configure iAMT Intel R Management Engine BIOS Extension v9 0 0 0024 Intel R ME v9 0 1 1333 Copyright c 2003 12 Intel Corporation All Rights Reserved INTEL RI AMT CONFIGURATION Manageability Fea
31. t panel display will be getting weaker as frequently used However the operating period varies depending on the application environment The flat panel display is not susceptible to shock or vibration When assembling the OPS883 series make sure toinstall it securely Do not leave this equipment in an uncontrolled environment where the storage temperature is below OC or above Abt It may damage the equipment External equipment intended for connection to signal input out or other connectors shall comply with relevant UL IEC standard Do not open the back cover of the system If opening the cover for maintenance is necessary only allow technicians to implement it Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the following precautions Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This will help to discharge any static electricity on your body Please wear a wrist grounding strap if you handling boards and eletronic components Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co Ltd IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation 3 Intel and Atom are registered trademarks of Intel Corporation MS DOS Microsoft C and Quick BASIC are trademarks of Microsoft Corporation VIA is a trademark of VIA Technologies
32. trends Inc Wake system with Fix Time Disabled Wake system with Fix Time Disabled Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc AMI BIOS Setup Utility 39 OPS883 User s Manual e Trusted Computing Enables or disables BIOS support for security device O S will not show Security Device TCG EFI protocol and INT1A interface will not be available TCG EFI protocol and INT1A interface will not be available Aptio Setup Utility Copyright C 2012 American Megatrends Inc TPM State Enabled TPM State Disabled Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc 40 AMI BIOS Setup Utility OPS883 User s Manual e CPU Configuration This screen shows the CPU Configuration and you can change the value of the selected option Aptio Setup Utility Copyright C 2012 American Megatrends Inc Active Processor Cores Version 2 15 1236 Copyright C 2012 American Megatrends Inc gt Active Processor Cores To select number of cores is to enable in each processor package gt Intel Virtualization Technology Allows a hardware platform to run multiple operating systems separately and simultaneously enabling one system to virtually function as several systems AMI BIOS Setup Utility 41 OPS883 User s Manual e SATA Configuration You can use this screen to select options for the SATA Configuration and change the value of the selected option A d
33. ture Selection Enabled gt SOL IDER KVM User Consent Password Policy SA aal Network Setup Activate Network Access Unconfigure Network Access Full Unprovision gt Remote Setup And configuration Power Control lt Move Highlight Enter Select Entry 62 Watchdog Timer OPS883 User s Manual 2 Select TCP IP to get into Network interface and set it to Enabled Get into DHCP Mode and set it to Disabled Intel R Management Engine BIOS Extension v9 0 0 0024 Intel R ME v9 0 1 1333 Copyright c 2003 12 Intel Corporation All Rights Reserved INTEL R ME NETWORK SETUP Intel R ME Network Name Settings CFIP Set it Move Highlight Enter Select Entry Esc Exit Intel R Management Engine BIOS Extension v9 0 0 0024 Intel R ME v9 0 1 1333 Copyright c 2003 12 Intel Corporation All Rights Reserved WIRED LAN IPv4 CONFIGURATION lt Enabled Enable Disable IPV4 DHCP Mode lt Move Highlight Enter Select Entry Esc Exit Watchdog Timer 63 OPS883 User s Manual 3 If DHCP Mode is disabled set the following settings e IP address e Subnet mask Intel R Management Engine BIOS Extension v9 0 0 0024 Intel R ME v9 0 1 1333 Copyright c 2003 12 Intel Corporation All Rights Reserved WIRED LAN IPV4 CONFIGURATION DHCP Mode Disabled IPv4 Address 10 1 40 714 Subnet Mask Address Default Gateway Address RAR Preferred DNS Address 0 0 0 0 Alternate DNS Address Subnet mask e g 2
Download Pdf Manuals
Related Search