Stretch FireWire
Contents
1. M4 200 201 Tip This installation advisory is highlighted to avoid power conflicts between self powered devices and controllers and unnecessarily applied external power 1 2 System Requirements for Setup Installation Important Please use the installation procedure below Improper or no operation may result if the start up sequence is not correctly followed Step 1 Carefully unpack the contents of the shipping group and Ensure no host or peripheral equipment is powered up Step 2 The M4 200 Firewire repeater boxes are identical Identify one as upstream or host and downstream or peripheral Step 3 Prepare a duplex LC patch cord fiber optic cable Multi Mode Glass Optical Fiber with 62 5 125 um or 50 0 125 um core Attach the two LC connector fiber cables first with no power applied to any system component as follows Tx Upstream to Rx Downstream Rx Upstream to Tx Downstream Power i a Status C Tx Rx Figure 2 End View of M4 200 Repeater Step 4 Connect the upstream box to the host computer using a copper Firewire cable by plugging into the host computer Firewire card and the upstream box Firewire port either one Connect the downstream box to the peripheral equipment in a similar manner Step 5 If there are non Opticis external power supplies to be attached do so now e g block power supplies for laptop Firewire PC cards downstream appliances etc Do NOT attach the Opticis power supplie2. or 1pcs x Bilingual port 9pin to Bilingual port 9pin for S800 O AC DC power adaptor One 1 unit O User s Manual O Duplex LC Multi Mode Optical Fiber Cable Optional can be provided by the user or by the reseller S 5 PC aca Ey Be Figure 1 Firewire repeater system with optional fiber cables 1 1 Welcome Product Description System Requirements for Setup O Hardware requirements m You have to have a 1394 a b controller having a DS bilingual port in your PC or Mac systems m No special requirements memory size CPU speed and chipsets if you ve already properly installed your 1394 controllers m Step by step connection of Multiple M4 201s is strongly recommended prior to install all M4 201 boxes in a time O Software requirements No special restrictions if you ve already properly installed your 1394 controller in your OS m Precaution Before using Opticis M4 200 201 you have to confirm to install proper device drivers which the device manufacture supplies designed for your operating system If not Opticis M4 200 201 might not work O AC DC Power Adapter Technical Advisory When IEEE 1394 Firewire devices or controllers are self powered the Power LED is illuminated and the shipping group s external DC power adapter is not required Use only if the Power LED is off when the entire system is powered up The power adaptor in the shipping group can supply to 1394 device up to 12V 1A 12W through
3. TICIS www opticis com P Stretch FireWire User s Manual M4 200 amp 201 cE Doc No OEB D130903 M4 Rev1 1 Manual Contents Manual Contents Welcome Product Description System Requirements for Setup Installation Troubleshooting Maintenance Technical Support Product Specifications Warranty Information Regulatory Statements Pictorials Figure 1 Firewire repeater system with optional fiber cables Figure 2 End View of M4 200 Repeater Figure 3 Side View of M4 200 Repeater Figure 4 End View of M4 201 Repeater Figure 5 Side View of M4 201 Repeater 1 0 Manual Contents meek kk OMNRDWM O0 Welcome Congratulations on your purchase of the Stretch Firewire M4 200 201 Optical FireWire Repeater System This manual contains information that will assist you in installing and operating the product Product Description Shipping Group M4 200 Oo M4 200 Optical Firewire Repeater Two 2 units O 0 7 meter 1394b copper cables Two 2 units 2pcs x Bilingual port 9pin to DS port 6pin for S400 or 2pcs x Bilingual port 9pin to Bilingual port 9pin for S800 O AC DC power adapter One 1 unit O User s Manual O Duplex LC Multi Mode Optical Fiber Cable Optional can be provided by the user or by the reseller M4 201 O M4 201 Optical Firewire Repeater One 1 unit O 0 7 meter 1394b copper cable One 1 unit 1pcs x Bilingual port 9pin to DS port 6pin for S400
4. of the next one You have to repeat Step 13 to 18 as many as you have The M4 201 giving connection of a 1394 device is capable of two way fiber connection in forward and backward directions which eventually makes a daisy chain with each repeater of M4 200 at both ends Do NOT plug in external power to the box if the PWR LED is on after the M4 200 201 repeater is connected to a live host or powered peripheral 1 5 Installation continued Troubleshooting The Power LEDs are not illuminated Ensure that all AC and DC plugs and jacks used by external power supplies both Opticis and others are firmly connected Ensure that power bars are live No controller or driver for the peripheral device exists in the Operating System OS device manager Reset the system Disconnect and reconnect 1394 b copper cables or DC power adapters Check if the two fibers are properly connected The Tx in one repeater goes to the Rx in the other and vice versa Remove the fiber cables and use a Firewire copper cable to connect the upstream and downstream boxes by plugging in to the unused bilingual ports The OS device manager shows the Firewire connection but the Firewire peripheral does not work properly Ensure that the correct software device driver is loaded on the processor platform Direct connect the peripheral to the processor s Firewire port to confirm operation Software drivers are usually available from the Internet Maintenance No
5. rage temperature 30 C to 60 C mM Humidity 5 to 95 AC DC Power Adapter O Power Input AC 100 240V 50 60Hz 0 1A O Power Output 12 V 1 0A SMPS DC power Adapter O Cord DC Jack Core is 12 V and outer is GND 1 7 Product Specifications Warranty Information 1 One Year Warranty Opticis warrants this optical Firewire repeater to be free from defects in workmanship and materials under normal use and service for a period of one 1 year from the date of purchase from Opticis or its authorized resellers lf a product does not work as warranted during the applicable warranty period Opticis shall at its option and expense repair the defective product or part deliver to customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the defective product All products that are replaced will become the property of Opticis Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day warranty or the reminder of the initial warranty period whichever is longer Opticis shall not be responsible for any software firmware information or memory data of customer contained in stored on or integrated with any products returned to Opticis for repair under warranty or not Warranty Limitation and Exclusion Opticis shall have no further obligation under the foregoing limited warranty if the product has been damaged due to abu
6. receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult a service representative for help Properly shielded and grounded cables and connectors must be used in order to comply with FCC emission limits Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Optical Safety Statement The Opticis M4 200 201 repeater uses an 850nm Multi Mode Vertical Cavity Surface Emitting Laser diode transmitter that has been designed to meet Class 1 eye safety 1 9 Regulatory Statements 2013 Opticis Co Ltd All Rights Reserved Revision 1 1 3 Sep 2013 Opticis Locations Headquarters Opticis Co Ltd 16Fl Kins Tower 8 Sungnam daero 331 beon gil Bundang gu Seongnam si Gyunggi do 463 844 South Korea Te 82 31 719 8033 Fax 82 31 719 8032 www opticis com For order support please contact your Distributor or Reseller For technical support check with the Opticis web site www opticis com or contact techsupp opticis com
7. s until instructed to do so Bilingual Port Figure 3 Side View of M4 200 Repeater 1 3 Installation Step 6 Power on the host and peripheral equipment At this point there must be no external power supplies plugged into the M4 200 upstream or downstream boxes Step 7 Observe the Power Light Emitting Diode on the side of the boxes If the upstream box LED is illuminated no external power supply is required Likewise if the downstream box LED is illuminated no external power supply is required Step 8 If both Power LEDs are illuminated then the Firewire link is active Proceed with the software bring up on the host system Ignore further steps Step 9 If one or both of the upstream downstream Power LEDs are dark then power down all equipment and plug in one or two Opticis power supplies Step 10 Power on complete system Both upstream downstream LEDs should be illuminated Proceed with host software bring up M4 201 installation Daisy Chain Step 1 Power off M4 200 host and peripheral equipment first Prepare two duplex LC patch cord fiber optic cable Multi Mode Glass Optical Fiber with 62 5 125 um or 50 0 125 um core Attach the four LC connector fiber cables with no power applied to any system component as follows Tx M4 200 to Rx M4 201 Rx M4 200 to Tx M4 201 Figure 4 End View of M4 201 Repeater Step 2 Connect the M4 200 box to the host computer and M4 201 to the peripheral equipment
8. se misuse neglect accident unusual physical or electrical stress unauthorized modifications tampering alterations or service other than by Opticis or its authorized agents causes other than from ordinary use or failure to properly use the Product in the application for which said Product is intended 1 8 Warranty Information FCC Statement This device complies with part 15 of FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction guide may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient or relocate the
9. special maintenance is required for the optical repeater boxes and power supplies If not in use insert the factory provided plug into the Tx Rx fiber port Ensure that the repeaters and power modules are stored or used in a benign environment free from liquid or dirt contamination There are no user serviceable parts Refer all service and repair issues to Opticis Technical Support and Service For commercial or general product support contact your reseller For technical service contact Opticis by email techsupport opticis com or visit our website at www opticis com 1 6 Troubleshooting Maintenance Technical Support Product Specifications M4 200 201 Optical Firewire Repeater O Electrical Specifications m Fully supports provisions of IEEE1394b 2002 M4 200 2 bilingual ports M4 201 1 bilingual port Power supply DC12 16V max 500mA Data rates S100 98 304 Mbps S200 196 608 Mbps S400 393 216 Mbps and S800 983 04 Mbps O Optical Specifications mM IEEE1394b 2002 compliant m Duplex LC type optical port supporting 62 5 um 50 0 um Multi mode Glass of Fiber Laser Class 1 Eye Safety compliant 850nm VCSEL Data rates S100 122 44 Mbps S200 245 76 Mbps S400 491 52 Mbps S800 983 04 Mbps O Mechanical Specifications M4 200 201 Box dimensions 101mm 24mm 91mm W H D Ma4 200 Weight 0 252 Kg M4 201 Weight 0 290 Kg O Environmental Specifications E Operating temperature 0 C to 50 C m Sto
10. using a copper Firewire cable and attach two LC connector fiber cables in between M4 200 and M4 201 boxes 1 4 Installation continued Step 3 If there are non Opticis external power supplies to be attached do so now e g block power supplies for laptop Firewire PC cards downstream appliances etc Do NOT attach the Opticis power supplies until instructed to do so 12VDC Bilingual Port Figure 5 Side View of M4 201 Repeater Step 4 Power up the host and peripheral equipment At this point there must be no external power supplies plugged into the M4 200 or M4 201 boxes Step 5 Observe the Power Light Emitting Diode on the side of the boxes If the M4 200 box LED is illuminated no external power supply is required Likewise if the M4 201 box LED is illuminated no external power supply is required Step 6 If both Power LEDs are illuminated then the Firewire link is active Proceed with the software bring up on the host system Ignore further steps Step 7 If one or both of the M4 200 M4 201 Power LEDs are dark then power down all equipment and plug in one or two Opticis power supplies Step 8 Power up complete system Both M4 200 M4 201 LEDs should be illuminated Proceed with host software bring up Step 9 If you have another M4 201 follow as Step 11 and connect the duplex LC multimode fiber cables to the next M4 201 as Step 12 The fiber connection is accomplished between the OUT of the prior M4 201 and the IN
Download Pdf Manuals
Related Search