Z30 LED CONTROLLER User Manual rel 2.1 Eng
Contents
1. 000 255 Proportional colour dig Z30 LED Controller DMX CHANNEL Parameter RED 4 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL Parameter GREEN 4 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL Parameter BLUE 4 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL Parameter RED 5 DMX range Mode Option Function Value 000 255 gt Proportional colour DMX CHANNEL Parameter GREEN 5 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL Parameter BLUE 5 DMX range Mode Option Function Value 000 255 Proportional colour aa Z30 LED Controller DMS CHANNEL Parameter RED 6 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL Parameter GREEN 6 DMX range Mode Option Function Value 000 255 Proportional colour DM CHANNEL Parameter BLUE 6 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL Parameter RED 7 DMX range Mode Option Function Value 000255 gt Proportional colour DMX CHANNEL Parameter GREEN 7 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL Parameter BLUE 7 DMX range Mode Option Function Value 000 255 Proportional colour Z30 LED Controller DMS2. Made in Italy The Lighting Company p www dts lighting it E Z30 LED Controller Le informazioni contenute in questo documento sono state attentamente redatte e controllate Tuttavia non assunta alcuna responsabilit per eventuali inesattezze Tutti diritti sono riservati e questo documento non puo essere copiato fotocopiato riprodotto per intero o in parte senza previo consenso scritto della D T S DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche funzionali o di design a ciascun proprio prodotto D T S non assume alcuna responsabilit sull uso o sull applicazione dei prodotti o dei circuiti descritti The information contained in this publication has been carefully prepared and checked However no responsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied or reproduced in part or completely without prior written consent from D T S D T S reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice D T S assumes no responsibility for the use or application of the products or circuits described herein Les informations contenues dans le pr sent manuel ont t r dig es et contr l es avec le plus grand soin Nous d clinons toutefois toute responsabilit en cas d ventuelles inexactitudes Tous droits r serv s Ce document ne peut tre copi photocopi
3. ou reproduit dans sa totalit ou partiellement sans le consentement pr alable de D T S D T S se r serve le droit d apporter toutes modifications et am liorations esth tiques fonctionnelles ou de design sans pr avis a chacun de ses produits D T S d cline toute responsabilit sur l utilisation ou sur l application des produits ou des circuits d crits Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y controladas Con todo no se asume ninguna responsabilidad por eventuales inexactitudes Todos los derechos han sido reservados y este documento no puede ser copiado fotocopiado o reproducido total o parcialmente sin previa autorizaci nescrita de D T S D T S se reserva el derecho a aportar sin previo aviso cambios y modificaciones de car cter est tico funcional o de dise o a cada producto suyo D T S no se asume responsabilidad de ning n tipo sobre la utilizaci n o sobre la aplicaci n de los productos o de los circuitos descritos Z30 LED Controller DESCRIPTION Overview Z30 is a power supply DMX LED controller designed to control the following D T S LED products FOCUS LED projectors MR16 LED lamps DIVE 3 FULL COLOUR DIVE 9 RGB DIVE 6 FULL COLOUR 2 Output needed DIVE 18 RGB 2 Output needed System Z30 is fitted with 10 outputs of 3 channels each max power of each output is 18W max power of each channel is 6W 6W RED 6W GREEN 6W BLUE Each output can supply and
4. 50 60 HZ Power Consumption Range 20 200 W Power Factor Pf 0 95 electronic PFC controller Efficiency 90 typical Output Power Output Range 10 outputs of 3 channels each Max power of each output is 18W 6W per channel Max power of each channel is 6W 6W Red 6W Green 6W Blue Output Current 350 mA 100 per channel 0 4 5W per channel 420 500 mA 100 per channel in BOOST Mode 0 6W per channel Output Voltage Vout 12V Max Load per output 3 x MR16 RGB LED lamps 1 x MR16 Full Color LED lamps 3 x FOCUS RGB LED projectors 1 x FOCUS Full Color LED projectors 1 x DIVE 3 FULL COLOUR 1 x DIVE 9 RGB DIVE 6 FULL COLOUR and DIVE 18 RGB need 2 x LEDs output to be properly driven Min Load output per group 1 x MR16 RGB LED lamp Control Input Control Signal DMX 512 Dimming System Constant Current PWM Address Range DMX 512 channels addressable by display 2 Z30 LED Controller IMPORTANT SAFETY INFORMATION Fire prevention Never locate the fixture on any flammable surface Minimum distance from flammable materials 10 cm Replace any blown or damaged fuses only with those of identical value Prevention from electric shock High voltage is present inside the unit Unplug the unit prior to performing any operation which involves touching the inside of the unit This equipment must be grounded do not connect to non grounded supplies The use of a thermal magnetic circuit breaker is recommended f
5. Z30 LED CONTROLLER 03 LA 077 V2 DIODOS RJ12 LED input male cable connector on board Focus Helios MR16 led lamps 123456 6 poles plug in screw connector M12 3CH LED output Female panel connector on board Z30 LED CONTROLLER 03 LA 073 V2 M12 3CH LED input Male cable connector mountable on request on FOCUS RGB LED projectors FOCUS Full Color LED projectors DIVE 3 6 FULL COLOUR DIVE 9 18 RGB LEDS CONNECTOR PINOUT Rj12 Pin 1 RED Pin 2 RED Pin 3 GREEN Pin 4 GREEN Pin 5 BLUE Pin 6 BLUE LEDS CONNECTOR PINOUT 6 poles plug in screw connector Pin 1 RED Pin 2 RED Pin 3 GREEN Pin 4 GREEN Pin 5 BLUE Pin 6 BLUE LEDS CONNECTOR PINOUT M12 3CH Pin 1 RED Pin 2 RED Pin 3 GREEN Pin 4 GREEN Pin 5 BLUE Pin 6 BLUE Pin 7 NOT CONNECTED Pin 8 NOT CONNECTED eu Z30 LED Controller LED UNITS WIRING CONNECTION 03 LA 072 V2 RJ12 OUTPUT J L SIT sim 6 pin Female RJ12 LEDs OUT 4 LEDs OUT 3 D T S T BOX CODE 03 LA 001 IMPORTANT The maximum number of MR16 FOCUS RGB LED lamps connectable to each 230 LEDs output is 3 pcs Never plug the cable coming from the Power suppl o 3 into OUT 1 or OUT 2 ofthe T BOX when other MR16 lamps are connected because a wrong connection
6. ce can seriously damage the lamps NEVER CONNECT NOR DISCONNECT A MR16 UNIT WHEN THE POWER SUPPLY IS TURNED ON MR16 RGB e The Maximum distance between the Z30 and the last AT 6 pin Male RJ12 MR16 unit in the line should not exceed 100 meters LS ANS Modular Plug aa Z30 LED Controller LED UNITS WIRING CONNECTION 03 LA 072 V2 RJ12 OUTPUT J L SIT sim m em ee o a tio SO DT A IO a AA me oui pen TE ii 6 pin Female RJ12 Zet ate toot IMPORTANT The maximum number of MR16 FOCUS FULL COLOUR LED lamps DIVE 3 FULL COLOUR DIVE 9 RGB connectable to each Z30 LEDs output is 1 pcs NEVER CONNECT NOR DISCONNECT A NEW UNIT WHEN THE POWER SUPPLY IS TURNED ON The Maximum distance between the Z30 DIVE 3 FULL COLOUR R and the LEDs unit in the line should not exceed 100 meters DIVE 9 RGB R DIVE9 RGB lt a Z30 LED Controller LED UNITS WIRING CONNECTION 03 LA 072 V2 RJ12 OUTPUT J L SIT y DA LACE ATA E CPUS RILIR 5 ap a PA LUR Ge CS u eS A ea eum oque Dmt CEP a ro oe e whe eee ee Geen es ae Gas meme m lt 1 a ema NI EA A PA A PT sim 6 pin Female RJ12 E ESSAS 2 X LED s output 2 XLED s output DIVE6 FULL COLOUR R y DIVE1S RGBR 2 X LED s output 2 X LED s output DIVE6 FULL COLOUR DIVE18 RGB IMPORTANT DIVE6 FULL COLOUR and DIVE18 RGB unit are provided with 2 separeted LED s input lines DIVE6 FULL COLOUR a
7. contrast Flip visual ON level Screen saver FLIP VISUAL Reverses display s reading depending on the mounting position on the ground or suspended BACKGROUND COLOR Background NORMAL Default Background REVERSE ENTER BACKGROUND COLOUR CONTRAST LEVEL To select the colour of the display 0 100 default 100 ENTER background CONTRAST LEVEL Display contrast SCREEN SAVER This menu allow to activate the screen saver SCREEN SAVER Screen saver TYPE default disabled Screen saver TIME default 10 sec ENTER Mode setting Menu Up Down ENTER Up Down DMX MODE To select DMX mode Full Type 8 bit 30 DMX ch Full Type 16 bit 60 DMX ch Z1 Type 8 bit 9 DMX ch Z1 Type 16 bit 12 DMX ch for Chase and Cue recording Z1 Full 8 bit 9x10 90 DMX ch Z1 Full 16 bit 12x10 120 DMX ch Z1 Short Full 8 bit 5x10 50 DMX ch Z1 Short Full 16 bit 8x10 80 DMX ch Custom map control 1CH Full mode Z30 LED Controller DMX MODE MAP Full type 8 bit 30 DMX ch default RGB 3ch each output 1 Red 2 Green 3 Blue ENTER Full type 16 bit 60 DMX ch mode RGB 2ch each colour 6ch each output 1 Red 8 bit 2 Red 16 bit 3 Green 8 bit 4 Green 16 bit 5 Blue 8 bit 6 Blue 16 bit Z1 type 8 bit 9 DMX ch mode with all the outputs automatically set on DMX starting channel 1 1 Shutter 2 Dimmer 3 Red 4 Green 5 Blue 6 White control 7 CTC 8 Macro 9 Function Z1 type 16 bit 12 D
8. control an independent set up of D T S LED products at the same time like one of the following max 3 x MR16 RGB LED lamps max 1x MR16 Full Color LED lamps max 3 x FOCUS RGB LED projectors max 1x FOCUS Full Color LED projectors max 1x DIVE 3 FULL COLOUR max 1x DIVE 9 RGB DIVE 6 FULL COLOUR and DIVE 18 RGB need 2 x LEDs output to be properly driven Interface Z30 is fitted with a LED interface that lets you enter all functions of the internal menu DMX Z30 LED CONTROLLER can be used in 10 DMX mode 120 ch 90 ch 80 ch 60 ch 50 ch 30 ch 12 ch 9 ch 1ch full or CUSTOM channels mode Operating system update Z30 internal operating system can be updated via computer through the dedicated D T S RED BOX interface Control Z30 can be controlled by any DMX console Construction Z30 is housed in a sturdy metal case that offers high resistance to knocks and mechanical stress Z30 is rack mountable The protection rating against external agents is IP20 Z30 LED Controller Connections DMX IN OUT 2 XLR 5 pole by Neutrik and 2 XLR 3 pole by Neutrik LEDs connector output Three models available RJ12 female connector 03 LA 072 V2 6 poles plug in screw connector 03 LA 077 V2 M12 3CH CONNECTOR 03 LA 073 V2 The Maximum distance between the Z30 and the last LED unit in the line should not exeed 100 meters MAIN ELECTRICAL CHARACTERISTICS Input Voltage Range Vin 90 260 Vac Frequency
9. CHANNEL Parameter RED 8 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL Parameter GREEN 8 DMX range Mode Option Function Value 000 255 Proportional colour DM CHANNEL Parameter BLUE 8 DMX range Mode Option Function Value 000 255 oo Proportional colour DMS CHANNEL Parameter RED 9 DMX range Mode Option Function Value 000255 gt Proportional colour DM CHANNEL Parameter GREEN 9 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL Parameter BLUE 9 DMX range Mode Option Function Value 000 255 Proportional colour dis Z30 LED Controller DMX range Mode Option Function Value 000 255 Proportional colour Parameter GREEN 10 DMX range Mode Option Function Value 000 255 Proportional colour DMX range Mode Option Function Value 000 255 Proportional colour a Z30 LED Controller DMX PROTOCOL 9 CHANNELS MODE SHUTTER DIMMER RED GREEN BLUE WHITE Pre programmed whites at different color temperatures CTC COLOURS MACRO FUNCTIONS OON A URWN ir Parameter SHUTTER DMX range Mode Option Function Value a Black out 10 19 Open 20 29 4 Black out 30 119 Strobe at variable speed from slow to fast 3400ms 20ms 120 149 Pulse open at variable speed from slow to fast 43s 100ms 150 179 Po Pulse clo
10. D s output each NOTE NOTE NOTE The information contained in this publication has been carefully prepared and checked However no responsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied or reproduced in part or completely without prior written consent from D T S D T S reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice D T S assumes no responsibility for the use or application of the products or circuits described herein MADE IN ITALY The Lighting Company ISO 9001 2008 D T S quality system is certified to the ISO 9001 2008 standard D T S products are designed and manufactured at the D T S plants in italy 05171154 D T S Illuminazione s r l Via Fagnano Selve 10 12 14 47843 Misano Adriatico RN Italy Tel 39 0541 611131 Fax 39 0541 611111 info dts lighting it www dts lighting it
11. MODE SETUP Automatic LEDs output settings without needing of an external DMX controller 3 different selectable options with Dimmer level Master level output 0 255 selectable by user Master Chase Rainbow game or Chase with 15 programmable scenes with Speed time and Wait time selectable by user Master Cue 7 selectable Cues with fixed colours Master White RGB 4 selectable Whites with different colour temperature CHASE RECORDER Chase with 15 user programmable scenes External DMX controller needed 730 is automatically forced to 12 DMX receiving channels when entering inside the CHASE RECORDER For the programming of Chase by using a DMX controller besides the 9 channels necessary to control the unit Z1 type 8 bit mode a further 5 DMX channels are needed So that in CHASE RECORDER mode the unit will need 12 channels to be correctly programmed The five new DMX channels are DMX CH 11 Scene number select Let you select the Scene to be programmed viewed 1 15 DMX ch 12 Scene status Edit Show Last Let you Edit the scenes View the previously programmed scenes or Set the last scene of the chase DMX ch 13 Scene speed 0 240 seconds Let you set the Scene speed time independend speed time for each scene of the Chase DMX ch 14 Scene wait 0 240 seconds Let you set the Scene Wait time independend Wait time for each scene of the Chase DMX ch 15 Store Let you store the programmed scene
12. MX ch mode with Dimmer and RGB channels with 16 bit control and all outputs automatically set on DMX starting address 1 1 Shutter 2 Dimmer 3 Red 8 bit 4 Red 16 bit 5 Green 8 bit 6 Green 16 bit 7 Blue 8 bit 8 Blue 16 bit 9 White control 10 CTC 11 Macros 12 Special Function Z1 full 8 bit 9x10 90 DMX ch mode same as Z1 type 8 bit 9 ch but each output with independent DMX control Output 1 DMX 1 Output 2 DMX 10 Output 3 DMX 19 Z1 full 16 bit 12x10 120 DMX ch mode same as Z1 type 16 bit 12ch but each output with independent DMX control Output 1 DMX 1 Output 2 DMX 13 Output 3 DMX 25 Z1 short full 8 bit 5x10 50 DMX ch mode with Dimmer Shutter and RGB 8 bit channels and each output with independent DMX control Output 1 DMX 1 Output 2 DMX 6 Output 3 DMX 11 Z1 short full 16 bit 8x10 80 DMX ch mode with RGB 16 bit each colour and each output with independent DMX control Output 1 DMX 1 Output 2 DMX 9 Output 3 DMX 17 1 Dimmer 2 Shutter 3 Red 8 bit 4 Red 16 bit 5 Green 8 bit 6 Green 16 bit 7 Blue 8 bit 8 Blue 16 bit Custom map DMX mode channels configuration selectable by user under Custom mode setup menu 1CH Full 1 DMX ch mode CUSTOM MODE SETUP DMX mode channels configuration selectable by user This menu let you set Shutter Dimmer Red Green Blue Ctc Macro and Function to the desired DMX channels Custom map control MASTER
13. T 2 DIVE3 FULL COLOUR DIVE9 RGB R IMPORTANT The maximum number of MR16 FOCUS FULL COLOUR LED lamps DIVE 3 FULL COLOUR DIVE 9 RGB connectable to each 230 LEDs output is 1 pcs NEVER CONNECT NOR DISCONNECT A NEW UNIT WHEN THE POWER SUPPLY IS TURNED ON The Maximum distance between the Z30 and the LEDs unit in the line should not exceed 100 meters so Z30 LED Controller LED UNITS WIRING CONNECTION 03 LA 073 V2 M12 3CH OUTPUT Pint M123CH LED output f f Pot 7B ta yE ROC Female panel connector E E p p Tm IMPORTANT The maximum number of MR16 FOCUS FULL COLOUR LED lamps DIVE 3 FULL COLOUR DIVE 9 RGB connectable to each Z30 LEDs output is 1 pcs NEVER CONNECT NOR DISCONNECT A NEW UNIT WHEN THE POWER aa SUPPLY IS TURNED ON The Maximum distance between the Z30 and the LEDs unit in the line should not exceed 100 meters DIVE18 RGB DIVE 3 FULL COLOUR R 2 X LED s output DIVE 9 RGB R 3 M12 3CH LED input Pin 1 RED 4 gt Male cable connector Pin 2 RED mountable on request Pin 3 GREEN 5 8 on board Pin 4 GREEN Pin 5 BLUE FOCUS RGB LED ectors mete ese Pin 6 BLUE pi 4 FOCUS Full Color LED projectors 7 FIN DIVE3 6 FULL COLOUR DIVE 9 18 RGB Pin 7 NOT CONNECTED Pin 8 NOT CONNECTED DIVE 6 FULL COLOUR and DIVE 18 RGB unit are provided with 2 separeted LED s input lines DIVE 6 FULL COLOUR and DIVE 18 RGB unit need 2 x Z30 LE
14. abled default Infrared enabled NOTE Internal hardware interface not yet implemented External infrared remote sensor needed D T S Code 03 LA 016 EMERGENCY SETUP Mode selection ON OFF default OFF Macro selection White COLD NATURAL WARM FULL DMX Macro DMX Program Save regolation Dimmer level 0 255 default 255 HARDWARE TEST Hardware test OFF default Hardware test ON LED MIN SETUP external DMX controller needed MIN level RED default 0 MIN level GREEN default 0 MIn level BLUE default 0 ENTER ENTER LED MAX SETUP External DMX controller needed MAX level RED default 255 MAX level GREEN default 255 MAX level BLUE default 255 ENTER MR16 FULL COLOUR MR16 limit OFF Default MR16 limit ON OUTPUT FILTER Output filter OFF Output filter ON Default OUTPUT DELAY No output delay Short delay default Long delay ENTER ENTER ENTER LED BOOST Led BOOST disabled 350mA Default Led BOOST MIN 420 mA Led BOOST MAX 500 mA ENTER 18 730 LED Controller Menu Up Down Measure ENTER Up Down e ks Lifetime voltage level temperature LIFETIME ENTER LIFETIME Unit lifetime This menu show the total UNIT LIFE LED Lifetime TIME reset not possible and the RGB life TIME reset possible VOLTAGE LEVEL I VOLTAGE LEVEL Internal voltage measure Internal voltage measure TEMPERATURE Internnal External temperature TEMPERATURE I measur
15. ale panel connector Pin 3 GREEN 3 Pin 4 GREEN 2 4 Pin 5 BLUE Pin 6 BLUE 8 Pin 7 NOT CONNECTED Pin 8 NOT CONNECTED Mains 90 260 Vac 50 60 Hz Powercon female panel connector M12 LED input Male cable connector For application where IP65 rating is not necessary Z30 LEDs cabling connection can be done with a standard UTP TIA EIA 568 B2 category 5E cable The maximum distance between power supply and the last unit on the line should not exceed 100 meters For IP65 rating application D T S reccomed the use of a IP65 68 cable as the 4X2XAWG24 multipolar black outdoor cable D T S Code 0509C062 The maximum distance between power supply and the last unit on the line should not exceed 100 meters 2 Z30 LED Controller DMX SIGNAL CONNECTION The unit operates using a digital DMX 512 signal Connection between the controller and the unit or between units must be carried out using a two pair screened g 0 5 mm cable and a CANNON XLR 3 5 pins connector Ensure that the conductors do not touch each other Do not connect the cable ground to the XLR chassis The plug housing must be isolated Connect the mixer signal to the DMX IN of the Z30 plug and connect it to the next unit by connecting the DMX OUT plug on the first Z30 to the DMX IN plug of the second one This way all the projectors are cascade connected vo ro gt j aw RIL2 PJ456 wae wes AAC DO LEA or ueta
16. ating INFRARED MODE it will be possible to navigate trought the unit functions by using the D T S infrared remote control D T S Code 0514L008 Internal hardware interface not yet implemented EMERGENCY SETUP Emergency operating mode By setting Emergency mode it will be possible to select one of the 5 preprogrammed WHITE cues that will then ran if DMX signal is missing or not available Dimmer level also selectable by user Usefull for Emergency EXIT ilumination on public areas I I LED Setup Menu Up Down ENTER Up Down Hardware test LED min setup LED max setup MR16 full colour Output filter output delay Led BOOST HARDWARE TEST Complete hardware test LED MIN SETUP This menu allow to select the minimum levels for Red Green Blue external DMX controller needed LED MAX SETUP This menu allow to select the maximum levels for Red Green Blue external DMX controller needed MR16 FULL COLOUR Preprogrammed RGB values for MR16 full colour led lamp OUTPUT FILTER Output filter OFF Output fileter ON default OUTPUT DELAY This menu allow to select the value of the delay in milliseconds for RGB and Dimmer channels reaction to DMX or Program variation No output delay 25 ms delay Short output delay 80 ms delay Long output delay 250 ms delay LED BOOST Led BOOST 350mA Led BOOST Min 420 mA Led BOOST Max 500 mA 15 Z30 LED Controller INFRARED MODE Infrared dis
17. cial function let you test all the LEDs output lines in order to check for possible problems on LEDs cabling connections Press Enter to confirm and Exit from TEST TEST CABLE MODE Press ENTER to confirm and EXIT from NE TEST a Z30 LED Controller DEFAULT SETTING To restore Factory settings UPLOAD FIRMWARE Upload the firmware via DMX ENTER This menu allow to upgrade the unit s software by computer gt IF Global setting Menu Up Down DEFAULT SETTING To restore Factory settings ENTER Up Down ENTER UPLOAD FIRMWARE Upload the firmware by DMX This menu allow to upgrade the unit s software by computer DOWNLOAD FIRMWARE This menu allow to save unit s programs into computer FORCE CABLE TEST This special function let you test all the LEDs output lines in order to check for possible problems on LEDs cabling connections once selected the Z8 Should be tuned OFF and ON again to run the TEST ENTER DOWNLOAD FIRMWARE This menu allow to save unit s programs into computer a FORCE CABLE TEST This special function let you test all the LEDs output lines in order to check for possible problems on LEDs cabling connections once selected the Z30 should be tuned OFF and ON again to launch the TEST ABOUT SS ABOUT E Rad code pcb revision Master pcb code pcb revision SW version I I Display Setting ES FLIP VISUAL Menu Up Down ENTER Up Down Flip visual OFF Default ENTER Flip Visual Background colour
18. e Internal External temperature measure DMX PROTOCOL Z30 RGB 30 CHANNELS MODE 60 CHANNELS MODE Default 1 RED 1 2 GREEN 1 3 BLUE 1 4 RED 2 5 GREEN 2 6 BLUE 2 7 RED 3 8 GREED 3 9 BLUE 3 10 RED 4 11 GREEN 4 12 BLUE 4 13 RED 5 14 GREEN 5 15 BLUE 5 17 RED GREED BLUE RED GREEN BLUE RED GREEN BLUE RED GREED BLUE RED OUUOAOOAONNN AO A 10 GREEN 10 BLUE 10 Z30 LED Controller DMX CHANNEL Parameter RED 1 DMX range Value 000 255 DMX CHANNEL Parameter GREEN DMX range Value 000 255 DMX CHANNEL Parameter BLUE 1 DMX range Value 000 255 Move range O O Move range OO SS OS Move range ae Proportional colour Proportional colour Proportional colour Proportional colour Proportional colour Proportional colour 8 Z30 LED Controller DMX CHANNEL ES Parameter RED 2 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL Parameter GREEN 2 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL ES Parameter BLUE 2 DMX range Mode Option Function Value 000 255 Proportional colour DMX CHANNEL Parameter RED 3 DMX range Mode Option Function Value 000255 gt Proportional colour cs ec DMX range Mode Option Function Value 000 255 Proportional colour DM CHANNEL ES Parameter BLUE 3 DMX range Mode Option Function Value
19. enu and set the following addresses on the mixer Projector 1 A001 Projector 2 A010 If you want to select the next projector just add 9 Projector 3 A019 Ed A projector 6 A046 Selelcting the DMX address 1 Press the UP DOWN key until you reach the required DMX address The numbers on the display will start flashing but the new DMX address hasn t yet been set 2 Press ENTER to confirm your selection The numbers on the display will stop flashing and the projector is now controlled by the new DMX address TIPS if you keep pushed the UP or DOWN keys the channels are calculated more quickly and you get a faster selection as 730 LED Controller DISPLAY FUNCTIONS Z30 LED CONTROLLER 03 LA 072 V2 3CH RJ12 OUTPUT 03 LA 073 V2 3CH M12 OUTPUT 03 LA 077 V2 PLUG IN OUTPUT MENU UP ENTER DOWN DISPLAY FUNCTIONS The Z30 display panel shows all the available functions Using these functions it is possible to change some of the parameters and add some functions Changing the D T S setting can vary the functions of the unit so that it does not respond to the DMX 512 signal used to control it Carefully follow the instructions below before carrying out any variations or selections NOTE the symbol gt shows which key has to be pushed to obtain the desired function Z30 Software version 3 30 TEST CABLE IN PROGRESS At the first Start Up 230 is forced in TEST CABLE MODE 20 Max LEDs power output This spe
20. le as the 4X2XAWG24 multipolar black outdoor cable D T S Code 0509C062 The maximum distance between power supply and the last unit on the line should not exceed 100 meters 4 Z30 LED Controller INPUT OUTPUT CONNECTIONS 03 LA 077 V2 PLUG IN OUTPUT Mains Switch Displays Mains 90 260 Vac 50 60 Hz Powercon female panel connector 22111111 ee ae TERE _ 1 o 2 A DMMXIN OMA OUT 3 DATA 10 x LEDs output E 6 poles plug in screw connector Pin 2 RED Pin 1 RED Pin 3 GREEN Pin 4 GREEN RE DSTSSS 6 poles plug in screw connector For application where IP65 rating is not necessary Z30 LEDs cabling connection can be done with a standard UTP TIA EIA 568 B2 category 5E cable The maximum distance between power supply and the last unit on the line should not exceed 100 meters For IP65 rating application D T S reccomed the use of a IP65 68 cable as the 4X2XAWG24 multipolar black outdoor cable D T S Code 0509C062 The maximum distance between power supply and the last unit on the line should not exceed 100 meters 8 INPUT OUTPUT CONNECTIONS 03 LA 073 V2 M12 3CH OUTPUT Z30 LED Controller Mains Switch Displays 10 x LEDs output M12 3CH Female panel connector Pin 1 RED M12 LED output Pin 2 RED Fem
21. n Value degrees IF CHANNEL 6 White WHITE CTC Dmx range value 206 255 0 255 43 color temp Correction Macros 0 2000 K 128 5500 K 255 7200 K IF CHANNEL 6 White NO FUNCTION Dmx range value 0 43 0 255 Smooth RGB linear Hue correction Z3O LED Controller DMX DMX CHANNEL 8 Parameter COLOUR MACROS Move DMX range range Mode Option Function Value SS ra 014 14 No Function Function aT TT 3044 Macro2 IE CI Macro IET Mtr 7589 Mr A Macro6 MAA Mater 120134 Macro8 135 149 Macro9 150 164 MacrodO 165 179 Macro 180 194 Macro dt 195 209 Macro 3 210 2235 Macro 226 239 Maro 240255 Macro O DMX CHANNEL 9 Parameter FUNCTIONS Recall Create and Store the Custom white Move DMA range range Mode Option Function Value degrees 079 0 O Custom White Recall Enable CH 6 for Custom white Recall 80 160 MO Custom White Create Enable CH 6 for Custom white Creation 161 255 N Custom White Store Store the Custom White created WIRING DIAGRAMS Z30 is available in three version with different LED output connectors 26 Z30 LED Controller RJ12 female connectors 03 LA 072 V2 6 poles plug in screw connectors 03 LA 077 v2 and M12 3CH connector 03 LA 073 V2 RJ12 Female panel connector on board Z30 LED CONTROLLER 03 LA 072 V2 Jd SIE Lp 6 pin Female RJ12 6 poles plug in screw connector on board
22. n cam ms aut coo INTE SSS ee s tf i prio a il Standard Yah 1 GND DMX 512 JEA zaa AL rre controller 3 E g mma JE qa E g mma Standard Day 1 GND DMX 512 Ja SS Lo dm controller ES If the display showing the DMX address flashes then one of the following errors has occurred DMX signal not present DMX reception problem For Installations where long distance DMX cable connections are needed we suggest to use a DMX terminator The DMX terminator is a male XLR 3 5 pins connector with a 120 ohm resistor Between pin 2 and 3 The DMX terminator must be plugged into the last unit DMX out panel connector of the DMX line PLACE A 120 OHM RESISTOR BETWEEN PIN 2 AND 3 OF A MALE XRL CONNECTOR AND PLUG IT INTO THE DMX OUT PANEL CONNECTOR OF THE LAST UNIT CONNECTED TO THE DMX LINE PIN 3 PIN 2 dE Z30 LED Controller DMX ADDRESS Z30 LED CONTROLLER can be used in 10 DMX mode 120 ch 90 ch 80 ch 60 ch 50 ch 30 ch 12 ch 9 ch ich full or CUSTOM channels mode If you want to use the Z30 in 30 channels mode select the 30 CH mode from the MODE menu and set the following addresses on the mixer Projector 1 AQO1 Projector 2 A031 If you want to select the next projector just add 30 Projector 3 A061 as A projector 6 A151 If you want to use the Z30 in 9 channels mode select the Z1 type map mode from the MODE m
23. nd DIVE18 RGB unit need 2 x Z30 LED s output each NEVER CONNECT NOR DISCONNECT A NEW UNIT WHEN THE POWER SUPPLY IS TURNED ON The Maximum distance between the Z30 and the LEDs unit in the line should not exceed 100 meters 2 Z30 LED Controller LED UNITS WIRING CONNECTION 03 LA 077 V2 PLUG IN OUTPUT THA MM i i i Lao e gg Il Y E Ll Ug J3 Um J a E ST ER matas li cl a ll o VM AO EE R R G G B B T 2 EE een LEDS OUT 3 1 PIN 6 N O IN IMPORTANT The maximum number of MR16 FOCUS RGB LED lamps connectable to each 230 LEDs output is 3 pcs NEVER CONNECT NOR DISCONNECT A MR16 UNIT WHEN THE POWER SUPPLY IS TURNED ON The Maximum distance between the Z30 and the last MR16 unit in the line should not exceed 100 meters MR16 RGB ai Z30 LED Controller LED UNITS WIRING CONNECTION 03 LA 077 V2 PLUG IN OUTPUT mms raz mas ms mas Pae mar mas n e gt L L I L L I E E LEDs OUT 10 VOY do A URL Aa a LEDs OUT 4 HEHE co LEDS OUT 3 a 1 P IN 6 LEDS OUTPUT 1 LEDS OUTPU
24. or each Z30 Use only AC supplies 90 260V 50 60Hz The unit should never be located in position exposed to rain or in areas of extreme humidity A good air ventilation is essential for proper equipment work Safety The external surface of the unit may exeed 50 C never handle the unit until at least 5 minutes have elapsed since the unit was turned off Never install the unit in an enclosed area lacking sufficient air flow The ambient temperature should not exeed 40 C and should not be lower than 10 C UNIT DIMENSION 432 mm Unit Dimensions LxDxH 480 x 385 x 88 mm Weight 7 5 Kg Packing Dimensions LxDxH 510 x 560 x 160 mm Weight 8 5 Kg E 730 LED Controller INPUT OUTPUT CONNECTIONS 03 LA 072 V2 RJ12 OUTPUT Mains Switch Displays Mains 90 260 Vac 50 60 Hz Powercon female panel connector 10 x LEDs output RJ12 Female panel connector Pin 1 RED Pin 2 RED Pin 3 GREEN mm TIL Pin 4 GREEN Pin 5 BLUE QS ET Pin 6 BLUE 6 1 1 6 6 pin Male Rj12 6 pin Female RJ12 4 WU 6 Modular Plug RJ12 6P6C 6P6C indicates 6 positions 6 cables For application where IP65 rating is not necessary Z30 LEDs cabling connection can be done with a standard UTP TIA EIA 568 B2 category 5E cable The maximum distance between power supply and the last unit on the line should not exceed 100 meters For IP65 rating application D T S reccomed the use of a IP65 68 cab
25. s Channel 12 Scene status should be set to Edit mode or to Set Last mode CUE RECORDER Single step Cue with Red Greed Blue output levels selectable by user Ki 230 LED Controller CUSTOM MODE SETUP SET dmx order DMX mode channels configuration selectable by user Block set wizard let you select the DMX starting address on every single output block 10 output blocks in total Example block 1 DMX 001 block 2 DMX 006 Block 3 DMX 011 Clear block setup DMX starting address reset ENTER MASTER MODE SETUP Leo Master selection Master disable Master Chase Master Cue Master White RGB Chase selection Chase Rainbow Chase Recorded Cue Selection Cue Red Cue Green Cue Blue Cue RED Green Cue Red Blue Cue Green Blue Cue Recorded configuration selectable by user White selection White Cold White Natural White Warm White Full Speed Time Chase speed time 1 240 seconds default 10 sec Wait time Chase wait time 1 240 seconds default 10 sec Dimmer level Master level output 0 255 default 255 CHASE RECORDER Scene setup Scene number Scene status Scene speed Scene wait Restore default Restore Factory settings ENTER CUE RECORDER Cue level Red Red intensity 0 255 default 255 Cue level Green Green intensity 0 255 default 255 Cue level Blue Blue intensity 0 255 default 255 ENTER INFRARED MODE Infrared remote control By activ
26. se at variable speed from slow to fast 43s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full 230 255 240 Open DMX CHANNEL Parameter DIMMER E Move DANDO renge range Mode Option Function Value ma A EE 0 255 Proportional dimmer _ AE Move DAMA range range Mode Option Function Value AA 0 255 Po Proportionalcolour lt a Z30 LED Controller DM CHANNEL ES Parameter GREEN NA Move DADA camge range Mode Option Function Value Se 0 255 o Proportionalcolour DMX CHANNEL Parameter BLUE Do Move DMX range range Mode Option Function Value aS eere 0 255 Proportional colour DMX CHANNEL 6 Parameter WHITE Pre programmed White at diff color temperature DMX range Mode Option Function Value 055 No Function 56 105 80 Full Red Green Blue at Full 106 155 130 White DTS IF CHANNEL 9 FUNCTIONS CUSTOM WHITE RECALL Dmx range value 0 79 156 205 180 Custom White Recall White CTC Channel 7 CTC enabled vee 2 43 color temp Correction Macros 2000 K 7200 K IF CHANNEL 9 FUNCTIONS CUSTOM WHITE CREATE Dmx range value 80 160 156 205 Custom White Create RGB levels selectable by DMX 206 255 White CTC Channel 7 CTC enabled 43 color temp Correction Macros 2000 K 7200 K _DMX CHANNEL 7 Parameter CTC Color temperature correction Move BA ate range Mode Option Functio
Download Pdf Manuals
Related Search