USER MANUAL - Kramer Electronics Japan Homepage
Contents
1. o 3 L KRAMER KRAMER N Destination United States KRAMER Figure 1 RC 2 Front Panel for Europe and the United States 2 KRAMER SIMPLE CREATIVE TECHNOLOGY Your RC 2 Figure 2 and Table 1 define the RC 2 rear panel Figure 2 RC 2 Rear Panel Table 1 Features and Functions of the RC 2 Feature Function 1 RC 2 Front Panel Front panel including 2 control buttons 2 PROGRAM ENABLE Switch For technical support use only 3 GND PIN Connects to the Ground 12V PIN Connects to the connector for powering the unit 4 RS 232 Terminal Block Connect to the RS 232 connector on the A V equipment or a PC Connector or other Serial Controller see section 4 1 Installing the Configuration Software 4 1 The RS 232 PINOUT The RS 232 9 pin D sub port PINOUT is defined in Figure 3 and Table 2 RS 232 PINOUT Figure 3 RS 232 PINOUT Connection Table 2 RS 232 PINOUT Connection Connect this PIN on the To this PIN on the Terminal Block Connector 9 pin D sub Connector Tx PIN 2 Rx PIN 3 GND PIN 5 5 Installing the Configuration Software To install the RC SV configuration software refer the RC SV Configuration guide 6 Configuring the RC 2 To configure the RC 2 buttons 1 Connect the power to the RC 2 and connect the RS 232 terminal block connector on the RC 2 unit to the 9 pin2. ast Description Cma3 ls RS 232 cma ls RS 232 Pa RC command Port Description Cmd1 RS 232 v Vendor Device Revision Driver command 3M H10 SA M Aspect Ratio 16 9 v Button Label Behavior Toggle 1 2 3 4 v Toggle States 4 Figure 5 Setting the Macro Sequences 7 Technical Specifications Table 3 defines the technical specifications Table 3 Technical Specifications of the RC 2 Wall Plate RS 232 Controller PORTS 1 RS 232 on a terminal block connector POWER SOURCE 12V DC 500mA adapter 40mA DIMENSIONS 1 gang Europe and the USA WEIGHT 0 3kg 0 67lbs approx ACCESSORIES RC SV configuration software OPTIONS RS 232 9 pin D sub port to 3 pin terminal block connector cable C D9F 3PM 0 6 1 Specifications are subject to change without notice KRAMER SIMPLE CREATIVE TECHNOLOGY LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by
3. D sub COM port on your PC as defined in section 4 1 2 Open the Configuration program The main RC SV Configuration window appears see Figure 4 1 Download up to date Kramer user manuals and guides from the Internet at this URL http www kramerelectronics com KRAMER SIMPLE CREATIVE TECHNOLOGY Configuring the RC 2 M Kramer RC SY Configuration tion Device Help Device Button Macro Ne E Description Delay Port i ls RS 232 Maste TRC EAE ls RS 232 Slave Keypad New f Duplicate a RC command Pot Desetnion Cm R5 232 Vendor i Revision Driver command 3M J vila Aspect Ratio 169 Delay after command Button lighting a seconds L mitiseconds Button Label Behavior Activate on Press K E OON Wm OFF m NoChange Figure 4 RC SV Configuration Window 3 Follow the instructions in the RC SV Configuration guide to configure the RC 2 buttons Technical Specifications 6 1 Setting the Macro Sequences The RC 2 configuration software RC SV Configuration software lets you assign up to four macro sequences each containing up to four commands to each button by setting the behavior drop down box in the button area to Toggle 1 2 3 4 and the toggle state to 4 In the Button Macro area press a toggle step 1 2 3 and 4 to write its Macro see Figure 5 Slave Keypad Button Macro
4. Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removalor installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal orinstallations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must t
5. may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION amp Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment Use the supplied DC power supply to feed power to the machine Please use recommended interconnection cables to connect the machine to other components FCC and CE approved using STP cable for twisted pair products For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution 9001 o 2 ge ia Institute of Quality amp Control Kramer Electronics Ltd Web site www kramerelectronics com E mail info kram
6. Kramer Electronics Ltd USER MANUAL Model RC 2 Wall Plate RS 232 Controller Contents Contents Introduction Getting Started Overview Your RC 2 The RS 232 PINOUT Installing the Configuration Software Configuring the RC 2 1 Setting the Macro Sequences Technical Specifications Figures Figure 1 RC 2 Front Panel for Europe and the United States Figure 2 RC 2 Rear Panel Figure 3 RS 232 PINOUT Connection Figure 4 RC SV Configuration Window Figure 5 Setting the Macro Sequences Tables Table 1 Features and Functions of the RC 2 Table 2 RS 232 PINOUT Connection Table 3 Technical Specifications of the RC 2 Wall Plate RS 232 Controller A oh A AN FSF DAUAN Bw Introduction 2 3 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Congratulations on purchasing your Kramer RC 2 Wall Plate RS 232 Controller The package includes the following items e RC 2 Wall Plate RS 232 Controller e This user manual e RC SV Configuration Software Getting Started
7. We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables Overview The RC 2 is a 1 Gang 2 button controller with an RS 232 port and two backlit and label capable buttons It sends an RS 232 command with the push of a button to a device such as a projector display or switcher via serial control protocols Each button can be assigned with up to four macro sequences containing up to four commands each 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 Download up to date Kramer user manuals from the Internet at http www kramerelectronics com 3 The complete list of Kramer cables is on our Web site at http www kramerelectronics com Your RC 2 4 Your RC 2 The RC 2 is available in three versions see Figure 1 one for Belgium and Germany one for England and Europe except Belgium and Germany and one for the United States Destination Belgium and Germany Destination England and Europe
8. ake or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This
9. erel com P N 2900 000417 REV 2
Download Pdf Manuals
Related Search