8 Gallon Wall Mount Vacuum Item # 412485
Contents
1. Total length of cord in feet 120V Ampere Rating More Not More AWG Than Than 18 16 12 Not recommended during unlatching always unplug power cord and remove the entire vac unit from wall bracket to empty tank or service filter Set unit on floor lift off tank cover refer to unpacking and setup After service place tank cover on tank securely and reinstall unit into hanging bracket The tool holder not standard with all models can be mounted on the wall in close proximity to the vacuum Figure 7 Secure with mounting hardware provided INSTALLING FOAM SLEEVE AND REUSABLE DRY FILTER Not standard with all models A WARN NG ALWAYS DISCONNECT THE PLUG FROM THE WALL OUTLET BEFORE REMOVING THE TANK COVER When using the reusable dry filter to pick up dust and dry material you must install foam sleeve and reusable dry filter to ensure proper filtration If the vacuum has been used to pick up liquids the foam sleeve must be cleaned and dried before installing for dry pick up With tank cover in an upside down position slide foam sleeve down over lid cage pulling until foam sleeve completely covers lid cage Figure 8 Center the reusable dry filter on lid cage Figure 9 slide mounting ring down over filter until ring is positioned against the ribs of the lid cage Figure 10 The reusable dry filter should always be in position over the foam sleeve for dry pick up To remove the filter for cleaning remove mountin2. A water wash is not always required depending on the condition of the foam sleeve 4 Gently wring out excess water blot foam sleeve with a clean towel and allow to dry The foam sleeve is now ready to to be reinstalled on the lid cage NOTE WET PICK UP ACCESSORIES SHOULD BE WASHED PERIODICALLY ESPECIALLY AFTER PICKING UP WET STICKY KITCHEN ACCIDENTS THIS CAN BE ACCOMPLISHED WITH A WARM SOLUTION OF SOAP AND WATER EMPTYING LIQUID WASTES FROM THE TANK Your Shop Vac Wet Dry vacuum may be emptied of liquid waste by removing the tank cover To empty stop the motor and remove the plug from the wall receptacle Remove the tank cover and deposit the liquid waste contents in a suitable drain After the tank is empty return the cover to its original position To continue use plug the cord into the wall receptacle and start the motor AUTOMATIC SUCTION SHUT OFF The vacuum is equipped with an automatic suction shut off that operates when picking up liquids As the level of the liquid rises in the tank an internal float rises until it seats itself against a seal at the intake of the motor shutting off suction When this happens the motor will develop a higher than normal pitch noise and the suction is drastically reduced If this occurs turn unit off immediately Failure to turn unit off after float rises and shuts off suction will result in extensive damage to the motor To continue use empty the liquid waste from the tank as
3. outlined in the previous paragraph NOTE IF ACCIDENTALLY TIPPED OVER THE VACUUM COULD LOSE SUCTION IF THIS OCCURS PLACE VAC IN UPRIGHT POSITION AND TURN SWITCH OFF THIS WILL ALLOW THE FLOAT TO RETURN TO ITS NORMAL POSITION AND YOU WILL BE ABLE TO CONTINUE OPERATION LUBRICATION No lubrication is necessary as the motor is equipped with lifetime lubricated bearings STORAGE Before storing your vacuum cleaner the tank should be emptied and cleaned The power cord can be wound around the housing of the unit for convenience Accessories may be stored in the tool holder not standard on all models so they can be readily available The vacuum should be stored indoors TROUBLESHOOTING Trouble Possible Cause Remedy Suction weakens or Clogged filter Brush dirt from filter If condition continues cleaner runs hot change filter Air leak Check all fittings for tight fit nozzles hose etc Check that tank cover is sealed properly Check nozzle hose etc for obstructions and remove if present Obstruction in hose or nozzle Misting in the Saturated filter exhaust air Replace saturated filter with a dry filter Position foam sleeve on the outside of groove around lid cage Foam sleeve incorrectly positioned A WARNING IF ANY OF THE MOTOR HOUSING PARTS SHOULD BECOME DETACHED OR BROKEN EXPOSING THE MOTOR OR ANY OTHER ELECTRICAL COMPONENTS OPERATION SHOULD BE DISCONTINUED IMMEDIATELY TO AVOID PERSONAL
4. 3 Replace tank cover and apply pressure with thumb to each latch until it snaps tightly in place Make sure all lid latches are clamped securely 4 Insert machine hose end with locking nut into inlet of tank and tighten Do not over tighten 5 Attach the extension wands to the accessory end of the hose Twist slightly to tighten the connection Figure 1 6 Attach one of the cleaning accessories depending on your cleaning requirements to the extension wands Twist slightly to tighten the connection Figure 1 7 Plug the cord into the wall outlet Your cleaner is ready for use ON 0 OFF NOTE MANY MORE USEFUL TOOLS ARE AVAILABLE AT YOUR LOCAL DEALER OR SHOP VAC WEBSITE SIDE TANK HANDLE ASSEMBLY Not standard with all models 2 Attach side handles to tank with screws provided Figure 2 MOUNTING INSTRUCTIONS Select mounting location at a wall stud and or provide a minimum 8 wide x 12 high x 3 4 thick surface which is strong enough to hold the weight of the vacuum unit with a full tank of debris A WARNING INADEQUATE MOUNTING COULD ALLOW THE UNIT TO FALL CAUSING INJURY AND OR DAMAGE TO THE UNIT Secure hanging bracket to mounting surface with 2 screws provided or other suitable fas tener NOTE The screws provided are adequate ONLY for mounting into wood Be sure to use the proper suitable fasteners for mounting vac to a surface other than wood Be sure bracket is level Figure
5. INJURY OR FURTHER DAMAGE TO THE VACUUM REPAIRS SHOULD BE MADE BEFORE REUSING THE VACUUM THREE YEAR HOME USE WARRANTY Your Shop Vac vacuum cleaner is warranted for normal household use in accordance with the User Manual against original defects in material and workmanship for a period of three years from date of purchase Should this product be used for commercial or rental use a 90 day limited warranty will apply Shop Vac Corporation warrants placing this vacuum cleaner in correct operating condition by repair or parts replacement during the warranty period without charge This warranty does not cover accessories Use of non recommended filters and or accessories may void the manufacturer s warranty Shop Vac assumes no responsibility for damage or faulty performance caused by misuse careless handling and where repairs or modifications have been made Do not attempt to service your vacuum beyond that described in the User Manual Proof of purchase date is required The warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province This warranty is void outside of the United States and Canada Mounting ring falling off Customers in the United States for product service contact Shop Vac Corporation Customer Service at 570 326 3557 or go to www shopvac com support Visit www shopvac com for your vacuum s parts list schematic
6. 3 2 Install vac by aligning ledge on back of tank to engage as the vac unit is lowered into the hanging bracket Figure 4 3 Instructions for installing and removing hose A Insert hose into inlet and tighten locking ring by turning clockwise Figure 5 B Unscrew locking ring by turning counter clockwise and remove from inlet Figure 6 4 Attach one of the cleaning accessories to the accessory end of the hose 5 Plug the cord into the wall outlet Your cleaner is ready for use ON 0 OFF To avoid possible injury or damage by dislodging unit from hanging bracket or dropping tank _h the plug illustrated in sketch A A temporary adaptor that looks like the adaptor illustrated in sketches B and C may be used to connect this plug to a 2 pole receptacle as shown in sketch B if a properly grounded outlet is not available The temporary adaptor should be used only until a properly grounded out let sketch A can be installed by a qualified electrician The green colored rigid ear lug or the like extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover Whenever the adaptor is used it must be held in place by a metal screw NOTE IN CANADA THE USE OF A TEMPORARY ADAPTOR IS NOT PERMITTED BY THE CANADIAN ELECTRICAL CODE ai Y ADAPTER fa METAL SCREW 11 TAB FOR GROUNDING SCREW GROUNDING GROUNDED PIN OUTLET BOX A B C EXTENSION CORDS
7. Thanks for shopping with Improvements a Gallon Wall Mount Vacuum Item 412485 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE AX WARNING 10 REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY Do not leave appliance when plugged in Unplug from outlet when not in use and before servic ing Connect to a properly grounded outlet only See Grounding Instructions Do not expose to rain store indoors Do not allow to be used as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only Manufacturer s recommended attachments Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water contact Shop Vac Corporation for assistance 6 Do Not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated sur faces 7 Do not unplug by pulling on cord To unplug grasp the plug not the cord 8 Do not handle plug or appliance with wet hands 9 Do not put any object into openings Do not use with any openings blocked keep free of dust lint hair and anything that may reduce air flow 10 Keep hair loose clothing fingers and all parts of body awa
8. cuuming small amounts of liquids For proper installation of the cartridge filter refer to Installing the Cartridge Filter For best results when vacuuming large quantities of liquid remove the cartridge filter When vacuuming liquids containing debris it is recommended purchasing a foam sleeve and install over filter cage otherwise a foam sleeve is not required for wet pick up Foam sleeve and additional filters may be purchased by visiting our website at www shopvac com contacting our customer service department or purchasing at your local Shop Vac distributor Misting in exhaust air may occur if the filter becomes saturated during wet pick up If misting occurs remove filter and allow to dry or replace with another dry filter to eliminate the misting and possible dripping of liquid around the lid Turn the unit off immediately upon completing a wet pick up job or when tank is full and ready to be emptied Raise the hose to drain any excess liquid into the tank The interior of the tank should be periodically cleaned The foam sleeve should be cleaned periodically as described in the following steps 1 Always disconnect the plug from the wall receptacle before removing the tank cover Place tank cover in an upside down position Remove foam sleeve by sliding it up and off the lid cage 2 Shake excess dust off foam sleeve with a rapid up and down movement 3 Hold foam sleeve under running water for a minute or two rinsing from the inside
9. dge filter off the lid cage Figures 15 amp 16 To clean the cartridge filter shake or brush off excess dirt or rinse from the inside of the filter with water dry completely approximately 24 hours and re install Figures 17 amp 18 Note If the filter has been used for wet pick up it must be cleaned and dried before using for dry pick up INSTALLING THE DISPOSABLE FILTER BAG 1 Grasp cardboard collar firmly and slide rubber guard onto inlet fitting as firmly as possible Figure 19 2 When securely in place expand and position bag down inside of tank Figure 20 3 Use for DRY PICK UP only 20 wn A WARNING THIS VACUUM CLEANER FILTER BAG SHOULD ONLY BE USED FOR COLLECTING DRY DIRT AND DEBRIS SAW DUST WOOD CHIPS ETC TO AVOID HEALTH HAZARDS FROM VAPORS OR DUST DO NOT USE FILTER TO VACUUM TOXIC CARCINOGENIC OR OTHER HAZARDOUS MATERIALS SUCH AS ASBESTOS PESTICIDES OR OTHER HEALTH ENDANGERING MATERIALS Keep filters clean Efficiency of the vacuum is largely dependent on the filters A clogged filter can Cause overheating and possibly damage the cleaner Check filters periodically and replace as required Replace with manufacturer recommended filter bag WET PICK UP OPERATION Remove ALL dirt and debris found in the tank The vacuum requires only a minimum of conver sion when going from dry to wet pick up Remove all dry use filters from the vacuum A clean cartridge filter may be used for va
10. e on a nominal 120 volt circuit and has a grounded plug that looks like When using the appliance at a distance where an extension cord becomes necessary a 3 conductor grounding cord of adequate size must be used for safety and to prevent loss of power and overheating Use the table below to determine A W G wire size required To determine ampere rating of your vacuum refer to nameplate located on rear of motor cover Before using appliance inspect power cord for loose or exposed wires and damaged insulation Make any needed repairs or replacements before using your appliance Use only three wire outdoor extension cords which have three prong grounding type plugs and three pole receptacles which accept the extension cord s plug When vacuuming liquids be sure the extension cord connection does not come in contact with the liquid NOTE STATIC SHOCKS ARE COMMON IN DRY AREAS OR WHEN THE RELATIVE HUMIDITY OF THE AIR IS LOW THIS IS ONLY TEMPORARY AND DOES NOT AFFECT THE USE OF THE APPLIANCE TO REDUCE THE FREQUENCY OF STATIC SHOCKS IN YOUR HOME THE BEST REMEDY IS TO ADD MOISTURE TO THE AIR WITH A CONSOLE OR INSTALLED HUMIDIFIER UNPACKING AND SET UP 1 Pull lid latches in an outward motion remove tank cover and any accessories that may have been shipped in the tank 2 Before replacing tank cover please refer to Dry Pick Up or Wet Pick Up Operation in this manual to ensure you have the proper filters installed for your cleaning operation
11. g ring and filter from lid cage Figure 11 To clean the reusable dry filter shake off excess dirt and dust or depending on the condition of the filter rinse with water Allow the filter to dry completely and re install DO NOT MACHINE WASH OR DRY NOTE ENSURE THAT THE MOUNTING RING IS COMPLETELY SECURE AND IN POSITION BY PRESSING DOWN FIRMLY AROUND THE RING IN SEVERAL PLACES BE SURE THE REUSABLE DRY DISC FILTER COMPLETELY COVERS THE FOAM SLEEVE CHECK TO ENSURE THAT ALL EDGES OF THE REUSABLE DRY FILTER ARE SECURE UNDER THE MOUNTING RING A CAUTION KEEP FILTERS CLEAN INSTALLING THE CARTRIDGE FILTER Not standard with all models The cartridge filter can be used for wet or dry pick up instal iz lation is the same for both When picking up large quantities of liquid please refer to the Wet Pick Up Operation section in this manual Use the cartridge filter in position over the lid cage for most general dry material pick up With the tank cover in an upside down position slide the cartridge filter down over the lid cage pushing until the filter seals against the cover Figure 12 Place filter retainer into the top of the cartridge filter hold the tank cover with one hand turn the handle on the filter retainer clockwise to tighten locking the filter into place Figures 13 amp 14 To remove the filter for cleaning again hold the tank cover and turn the filter retainer counter clockwise to loosen and remove slide the cartri
12. s when operating vacuum 23 STAY ALERT Watch what you are doing and use common sense Do not use vacuum cleaner when you are tired distracted or under the influence of drugs alcohol or medica tion causing diminished control If you have any questions regarding this product IM PROVEM ENTS call 1 800 642 2112 and ask for our product Lena aii specialists Mon Fri 9 00 5 00 EST or e mail Te order call productspecialist improvementscatalog com 1 800 642 21 12 oe See many more products on the Internet West Chester OH 45069 www improvementsCatalog com GROUNDING INSTRUCTIONS GROUNDING METHODS GROUNDED cama This appliance must be grounded If it should malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock This appli ance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances AWARN NG IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONDUCTOR CAN RESULT IN A RISK OF ELECTRIC SHOCK CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE PERSON IF YOU ARE IN DOUBT AS TO WHETHER THE OUTLET IS PROPERLY GROUNDED DO NOT MODIFY THE PLUG PROVIDED WITH THE APPLIANCE IF IT WILL NOT FIT THE OUTLET HAVE A PROPER OUTLET INSTALLED BY A QUALI FIED ELECTRICIAN This appliance is for us
13. y from openings and moving parts 11 Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes ay a wh 12 Do not use without dust bag and or filters in place 13 Turn off all controls before unplugging 14 Use extra care when cleaning on stairs 15 Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present 16 Donot use your cleaner as a sprayer of flammable liquids such as oil base paints lacquers household cleaners etc 17 Do not vacuum toxic carcinogenic combustible or other hazardous materials such as asbestos arsenic barium beryllium lead pesticides or other health endangering materi als Specially designed units are available for these purposes 18 Do not pick up soot cement plaster or drywall dust without cartridge filter and collection filter bag in place These are very fine particles that may pass through the foam and affect the performance of the motor or be exhausted back into the air Additional collection filter bags are available 19 Do not leave the cord lying on the floor once you have finished the cleaning job It can become a tripping hazard 20 Use special care when emptying heavily loaded tanks 21 To avoid spontaneous combustion empty tank after each use 22 The operation of a utility vac can result in foreign objects being blown into eyes which can result in eye damage Always wear safety goggle
Download Pdf Manuals
Related Search