Home

MODEL # : FIM

1. Q h y WHYNTER FREESTANDING ICE MAKER MODEL FIM 450HS Instruction Manual Congratulations on your new WHYNTER product To ensure proper operation please read this Instruction Manual carefully before using this product Keep this manual in a safe place for future reference TABLE OF CONTENTS E PARTS AND FEATURES 3 SAFETY PRECAUTIONS 4 REQUIREMENTS 5 OPERATION 6 USING THE CONTROL PANEL 6 INSTALLING THE WATER LINE 7 DRAINING THE UNIT 8 LEVELING THE ICE MAKER 8 CLEANING AND MAINTENANCE 9 SPECIFICATIONS 10 TROUBLESHOOTING 11 12 WARRANTY INFORMATION 13 FEATURES With the Whynter FIM 450HS Ice Maker you can produce up to 44 Ibs of ice per day while buffering up to 7 7 los of ice making this ice maker the perfect solution for convenient and fresh ice This efficient direct plumbing ice maker allows you a constant supply of bullet shaped ice at a much higher rate relative to manual fill ice makers When entertaining guests or just for daily use never again have to wait or rush to the store to purchase overpriced ice Attractive and compact this full stainless steel exterior ice maker is a great highlight to any space and fits easily were needed the most In case of water shortage or ice full in cabinet the indicator on the operation board will light on accordingly and the ice maker will stop operation automatically The ice storage cabinet is PU foamed so it is insulated well and
2. will automatically start making more ice 10 TROUBLESHOOTING Many common ice maker problems are easily resolved Try the troubleshooting suggestions below to see if the problems can be resolved before having to contact the service department Problem Possible Cause Probable Correction The machine won t operate e The icemaker is unplugged e The fuse is blown e The icemaker power switch is OFF e The ice storage bin is full of ice Plug the ice maker in Replace fuse Turn the ice maker power switch to ICE ON Take away some ice cubes make the ice full probe is free of ice The water doesn t feed in after the ice maker starts e The water supply tap is turn off e The water supply pipe is not proper connected e Water press is too low or too high Turn on the water supply tap Reconnect the water supply pipe Adjust water pressure Machine makes ice but bin does not fill up with ice e The condenser may be dirty e The air flow to the ice maker may be obstructed e The ambient temperature and water temperature are high or it is near with some heat source Check the installation and make sure there is at least 4 of clearance on each side and back Run the unit for longer period of time Clean the condenser Water is leaking out the unit e A few water droplets are on the door e The water supply connection is leaking Under some conditions humidity may co
3. it could prevent the ice from melting Including a plastic ice scoop water hose and drain hose this ice maker is great for making sure you get the ice you need The adjustable leveling leg at the bottom of the ice maker allows you to place the unit in any environment without it being uneven Ideal for any household this ice maker will be sure to be the hit of the party with your guests PARTS Power Switch lce Maker Door Air Outlet Display Panel lce Level Sensor lce Storage Container lce Scoop Bottom Floor Feet Power Cord 10 Water Inlet Valve memme 225 I 11 Drain Outlet Naa 12 Water Hose TTT li 13 Drain Tube 8 GE 14 Copper Water Inlet Adaptor OONDARWDND TO REDUCE THE RISK OF FIRE ELECTRICAL A WARNING Y SHOCK OR INJURY WHEN USING YOUR ICE MAKER FOLLOW THESE BASIC PRECAUTIONS READ ALL INSTRUCTIONS BEFORE USING THE ICE MAKER WARNING RISK OF DANGER TO SMALL CHILDREN AND SMALL ANIMALS ENTRAPMENT AND SUFFOCATION DANGER IF NOT PROPERLY SECURED DISPOSED OR ABANDONED APPLIANCES ARE STILL DANGEROUS BEFORE YOU DISPOSE OF YOUR ICE MAKER REMOVE THE DOOR TO PREVENT CHILDREN FROM CLIMBING INTO THE UNIT NEVER ALLOW CHILDREN TO OPERATE PLAY WITH OR CRAWL INTO THE APPLIANCE NEVER CLEAN ICE MAKER PARTS WITH FLAMMABLE FLUIDS THE FUMES CAN CREATE A FIRE HAZARD DO NOT STORE OR USE GASOLINE OR ANY OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER AP
4. the water inlet valve on the back of the ice maker 3 Connect the drainage tube on water outlet valve 4 Lightly tighten the compression fitting around the water line with an adjustable wrench or similar tool Draining the unit This unit operates in a gravity drain system which clears excess water from the ice maker to ensure a continuous supply of ice A water drain hose is provided with this unit Firmly attach the drain hose to the drain outlet Please note that the outlet of drain hose should be lower than ice maker so the water can flow out easily Normal Sounds Your new ice maker may make sounds that are not familiar to you Most of the new sounds are normal Hard surfaces like the floor walls can make the sounds seem louder than they actually are The following describes the kinds of sounds that might be new to you and what may be making them The ice case motor will make a whirling noise when the ice case and shovel are moving Rattling noises may be produced from the flow of the refrigerant The compressor may make a pulsating or high pitched sound The compressor may also produce a low tone humming sound Water that is being pumped into the ice case will make trickling dripping or splashing sounds e As each cycle ends you may hear a gurgling sound due to the refrigerant flowing e You may hear fan noise and air being forced over the condenser by the condenser fan e During the harvest cycle you may hear the sound of ice cu
5. IMPLIED WARRANTIES SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE Please retain the original proof of purchase in order to obtain warranty services Warranty begins from the original date of purchase To obtain service or information contact Whynter via email at service whynter com or call 866 WHYNTER Product contents and specifications may change without notice Copyright 2014 Whynter LLC www Whynter com 13
6. PLIANCE THE FUMES CAN CREATE A FIRE HAZARD SAFETY PRECAUTIONS Read all of the instructions before using this appliance When using this appliance always exercise basic safety precautions including the following Do not use if the power supply cord is damaged If damaged it must be replaced by qualified technician electrician Ensure the ice maker is unplugged before cleaning or if not in use To clean the ice maker use only mild detergents or glass cleaning products Never use harsh chemicals or solvents Do not use this ice maker with an extension cord or power strip Please ensure that the appliance is plugged directly into the electrical outlet Close the ice maker door immediately after opening Avoid placing the ice maker near external heat sources or direct sunlight Make sure the ice maker is placed on a flat level and solid surface Make sure that the surface on which the ice maker is placed is strong enough to hold the ice maker once it is fully loaded with ice The ice maker is an electrical appliance To avoid serious injury from electrical shock do not operate the ice maker with wet hands while standing on a wet surface or while standing in water Do not expose this appliance to rain or excessive moisture Do not turn the ice maker upside down on its side or 45 or more off level Never pull the power cord to disconnect the unit from an outlet Grasp the plug directly and pull it from the outlet This ice m
7. ad all safety precautions listed at the beginning of this manual It is recommended that a separate circuit serving only your ice maker be provided Use receptacles that cannot be turned off by a switch or pull chain The ice maker is equipped with a power supply cord having a 3 prong grounding plug To minimize possible shock hazard the cord must be plugged into a mating 3 pronged and grounding type wall receptacle providing 110 120V 60Hz grounded in accordance with the National Electrical Code and local codes and ordinances If a mating wall receptacle is not available it is the personal responsibility of the customer to have a properly grounded 3 prong wall receptacle installed by a certified electrician OPERATION A WARNING A Discard the first batch of ice produced by the freestanding ice maker Direct sunlight may cause the ice full infrared sensor to malfunction If the unit continues to produce ice even though the basket is full you may need to move the unit away from the sunlight Before using your ice maker it is strongly recommended to clean it thoroughly Read and follow the Cleaning and Maintenance section of the manual before proceeding Follow the steps below to start using your ice maker 1 Open the door and remove any packaging tape that may be holding down the ice case ice shovel and ice scoop Remove the ice scoop 2 Clean the ice storage container 3 Connect the direct water line into the water inlet assemb
8. aker is designed for non commercial use only When use for the first time or when restart after long period of unused the ice made for the first two times is not edible Do not plug this ice maker into the power socket before setup is completed The cord should be secured behind the unit and should not be left exposed or dangling Do not move this ice maker without securing the door Performance may vary based on operational and ambient conditions WARNING A Do not remove any safety warning or product information labels from your ice maker Before you begin Preparing the Ice Maker for use before you plug the ice maker in to a power supply be sure to let it stand upright for at least 24 hours to allow the compressor s oils to settle Unpacking the Ice Maker Carefully remove the packaging materials Remove any shipping tape and glue from your ice maker before using Do not use sharp instruments rubbing alcohol flammable fluids or abrasive cleaners to remove tape or glue These products can damage the surface of your icemaker Check to make sure the ice scoop and hoses are included If any parts are missing please contact our customer service Put the ice maker on a level and flat surface away from direct sunlight and other sources of heat such as a stove furnace radiator etc The appliance must be positioned so that the power plug is accessible REQUIREMENTS Installation Requirements The ice maker has been designed f
9. aker problems are easily resolved Try the troubleshooting suggestions below to see if the problems can be resolved before having to contact the service department Problem Possible Cause Probable Correction Unit is overfilling e Water pressure is too high e Ensure water pressure is a minimum Water overflow 14 7 psi and a maximum of 55 psi e Defective Water Sensor e Inspect water sensor Contact Whynter Service Department for details e Drain line elevated e Ensure gravity drain line is directed downward e Normal water removal e 0 5L of unused water is discarded and drained with each cycle 12 ONE YEAR LIMITED WARRANTY This WHYNTER Ice maker is warranted to the original owner within the 48 continental states for one year from the date of purchase against defects in material and workmanship under normal use and service Should your ice maker prove defective within one year from the date of purchase return the defective part or unit freight prepaid within two months of purchase after two months to one year customer will be responsible for freight cost to Whynter s service department along with an explanation of the claim to Whynter LLC Please package the ice maker carefully in its original packaging material to avoid damage in transit Please retain the original box and packaging material Under this warranty Whynter will repair or replace any parts found defective This warranty is not transferable After th
10. bes falling into the ice basket e If the ice maker is run without water the water pump will make a screeching noise Note Do not run the unit without water Leveling the Ice Maker It is important for the icemaker to be leveled in order to work properly It can be raised or lowered by turning the four feet on the bottom of the machine We recommend using a carpenter s level to check the machine 1 Place a carpenter s level on top of the product to see if the ice maker is level from front to back and side to side 2 Adjust the height of the feet as follows e Turn the leveling feet to the right to lower that side of the ice maker e Turn the leveling feet to the left to raise that side of the ice maker CLEANING AND MAINTENANCE The ice maker must be thoroughly cleaned if it has been left unused for a long time DO NOT turn the ice machine upside down to dry This will cause the oils from the compressor to shift which can result in the machine breaking or becoming inoperable Periodic cleaning and proper maintenance will ensure efficiency top performance and long life Never use a solvent based cleaning agent These cleaners may transmit taste to the ice cubes or damage and discolor the interior ALWAYS unplug the unit before cleaning the exterior and interior Before using your ice maker you are strongly recommended to clean it thoroughly This pr
11. ds When the batch of ice has been fully formed the ice maker stops the freeze cycle and begins the harvest cycle A valve opens diverting hot refrigerant gas into the evaporator rods The gas heats the rods causing the ice cube bullets to slide off the evaporator The hinged ice case will move out of the way for the formed ice cubes to drop onto the slide and be deposited into the ice bin The ice case will then resume its horizontal position and be filled with water for the next batch of ice to be made The ice maker will then produce ice until ice reaches the ice full sensor Once enough of the ice has melted the ice maker will automatically start making more ice The ice maker is insulated but not refrigerated Harvested ice will slowly melt and drain through the gravity drain The ice maker will automatically begin making more ice Installing the Water Line The direct water line can be installed into the ice maker for a continuous flow of water preventing you from refilling a water tank every time you need more ice The ice maker is designed with a direct water line for continuous operation The internal ice tray does not require manual filling NOTE All the required or customized hardware is not provided for installation so it is necessary to hire a professional licensed plumber to complete the installation 1 Connect the water line to your water source and be sure to tighten the connection to avoid leaking 2 Hand screw the water line into
12. e expiration of the warranty the cost of labor and parts will be the responsibility of the original owner of the unit THIS WARRANTY DOES NOT COVER e Acts of God such as fire flood hurricanes earthquakes and tornadoes e Damage accidental or otherwise to the ice maker while in the possession of a consumer not caused by a defect in material or workmanship e Damage caused by consumer misuse tampering or failure to follow the care and special handling provisions in the instructions e Damage to the finish of the case or other appearance parts caused by wear e Damage caused by repairs or alterations to the product by anyone other than authorized by the manufacturer e Freight and Insurance cost for the warranty service DISCLAIMER OF IMPLIED WARRANTIES LIMITATION OF REMEDIES CUSTOMER S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN CLAIMS BASED ON IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW BUT NOT LESS THAN ONE YEAR WHYNTER SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE QUENTIAL DAMAGES OR LIMITATIONS ON THE DURATION OF
13. ly 4 Close the door lid 5 Plug the ice maker s power plug in to a grounded outlet 6 Press the On Off power switch on the Control Panel 7 Ice will be created and fill the ice storage container Notes If the water pump is unable to detect or pump water the unit will stop automatically and the Water Low indicator will be lit Make sure that the water line has the correct amount of pressure water pressure must be a minimum 14 7psi and a maximum of 55psi and restart the unit by pressing the On Off button twice The ice maker will continue making ice until the ice basket is full When the ice basket is full Ice Full indicator will be lit USING THE CONTROL PANEL Power Switch Indicator Lights Switch Function POWER Turns the unit on or off Indicator Function RUN Ice Production is in process ICE FULL Indicates ice basket is full WATER LOW Indicates low water level in water in the reservoir How the Freestanding Ice Maker Produces Ice After the unit is powered on the ice maker begins with rotating the ice case into a horizontal water fill position under the evaporator rods The water pump is engaged and fills the ice case with water Water overflows for a few seconds before the compressor turns on The compressor then pumps refrigerant and the fan will turn on automatically after the condenser heats up The unit will be producing bullet shaped ice around the stainless steel evaporator ro
14. ndense on the door Consider moving the unit or just be more careful when you open the door Tighten fitting See Installing the water line Cubes are partially formed are white at e Not enough water in the water bin Check if the water supply pressure is correct Check water supply filter may be restricted Ve BONEN e Check for a water leak at the water trough Noise duri e The feet are not leveled and e Level and lock the feet See Leveling oie QUIN locked the Ice Maker operation e Certain sounds are normal See Normal Sounds section The icemaker stops suddenly while making ice e The electricity is off e The room temperature is out of the stated range Reconnect the power supply line Cut off the electricity and let the ice maker stop working until the temperature returns within the stated range The body of the ice maker is electrified e The ground line isn t in the socket Use the correct plug and outlet Scale builds up quickly inside the machine e The calcium level in the water is too high Use a water softening apparatus installed in front of the water inlet valve The ice storage bin is filled with water e The gravity drain is directed in an upward direction The gravity drain must be directed in a downward direction The unit is overfilling the ice making tray Contact Whynter 11 TROUBLESHOOTING Many common ice m
15. ocess should clean the unit of any impurities that may have been left behind during the manufacturing process 1 Unplug the water line from the ice maker 2 Clean the interior with a diluted cleaning solution warm water and a soft cloth DO NOT use any caustic or abrasive solutions Do not clean your ice maker with flammable fluids 3 The outside of the ice maker should be cleaned regularly with a mild detergent and warm water 4 Dry the interior and exterior with a soft cloth If the ice has a strange or plastic taste If the ice has an unappealing taste or the unit develops a musty odor try cleaning the water line of the ice maker with a mild white vinegar solution or lemon juice and then soak the line in hot water After that run a few cycles with plain water to eliminate all traces of the vinegar or lemon juice Throw out the first two ice batches after cleaning If you find the bad taste remains after this procedure use a solution of 2 tablespoons of baking soda and hot water to soak the water line Leave overnight to absorb any remaining odors tastes Drain the solution rinse the line with water and dry the line thoroughly Routine maintenance 1 Add a mild cleaning solution mixture to the ice storage container Use a 10 1 ratio of water to either white vinegar or lemon juice 2 Scrub the interior of the ice maker including evaporator rods with the solution 3 Remove the water line from the ice maker Use the solution
16. or free standing installation which will allow you to install the unit in almost any place you desire Please make sure to follow the instructions for clearance water and electrical requirements Clearance and Environment Requirements e Choose a well ventilated area with temperatures above 50 F and below 90 F Operation outside these temperatures may result in lowered production or may cause other adverse effects e This unit MUST be installed in an area protected from the elements e g wind rain water spray or drips The icemaker should not be located next to ovens grills or other high heat sources e The unit should be located on a firm and level surface that is able to support the ice maker s total weight with water e This is a freestanding appliance all ventilation is located at the back and rear sides Please note that without proper clearance and circulated airflow around the vents the unit may not operate properly Built in application is not recommended Water Requirements e Only use potable water or water suitable for drinking e The temperature of the water should be between 51 F and 90 F e Change the water in the water reservoir every 24 hours to ensure a reasonable hygiene level Note The add water light uses an electronic sensor that may not detect purified filtered reverse osmosis or distilled water You may need to add a pinch of salt to the water to increase the mineral content Electrical Requirements Re
17. to clean the water line as well 3 Drain the solution from the ice maker Wipe down ice maker interior and water line with hot water 4 Run the ice maker to make a few batches of ice Discard the ice 7 Your ice maker is now clean and should provide clean ice If the ice maker will not be used for an extended period of time you should unplug the unit from power drain the water from the reservoir and dry the interior with a clean soft cloth Note Do not touch the power plug when your hands are wet Note Never unplug the unit by pulling on the plug SPECIFICATIONS Description of product Freestanding Ice Maker Voltage Frequency AC 115V 60Hz Ice Making Ice Harvest rated current 1 2A 3 5A Color Stainless Steel Ice Storage capacity 7 7 Ibs Ice making capability 44 lbs day Refrigerant R134a Dimensions Width x Depth x Height 14 7 8 x 18 13 16 x 23 3 16 Weight 60 Ibs Note Technical data and performance information provided for reference only Specifications are subject to change Check the rating label on the ice maker for the most accurate information The actual quantity of ice produced in a 24hour period will vary with room and water conditions Notes on ice storage The ice maker will automatically shut off when the ice bin is full The ice bin compartment is insulated but not refrigerated and the ice in the bin will slowly Once enough of the ice has melted the ice maker

MODEL # : FIM

Contents

Download Pdf Manuals

Related Search

Related Contents