User Manual ICY4002IC ICY Connect
Contents
1. Adapter plug Display Adapter www icy connect nl _ Installation Placing antenna Screw the supplied antenna on top of the ICY Connect and turn it clockwise to tighten the antenna until it fits hand tight 8 LCY B V Preparation Placing adapter plug Insert the adapter plug into the ICY Connect Then connect the adapter to the outlet The ICY Connect is now ready for use At start up you see successively Software version This takes a few seconds E5 means your ICY Connect is out of range see page 12 E4 means your ICY Connect is in range but is not yet activated gt A number with 2 digits means that your SIM card is activated see page 11 This is the PIN code you need to install a main number see page 14 www icy connect nl 9 Attatch to the wall You can attach the ICY Connect to the wall if you have found a place with good range see also page 12 and near a power outlet Open the flaps on the front of the ICY Connect so that the screw holes are visible Use the given screws and plugs for mounting Screw holes for mounting on the wall 10 LCY B V Subscription choice and registration ICY Connect only works with the installed SIMcard You need a subscription before you can use ICY Connect As soon as you have done this you will rec2. can set the reply mode to off Setting the reply mode can only be done with the main number www icy connect nl Programming Setting reply mode Reply on Reply turned on You receive a confirmation text message after changes in settings Reply off Reply turned off You do not receive confirmation text messages after changes in settings LCY B V Programming Linking Thermostat With the ICY Connect you can control a Timer Thermostat Expert ICY1845IN Expert or Clever Thermostat PRO ICY3815TT PRO For correct thermostat installation see the supplied manual Once the thermostat is connected it will be recognized by the ICY Connect Add thermostat A thermostat can only be added from the main number You will need 1 Product code ICY1845 or ICY3815 2 4 digit address code that can be found on the back of the thermostat with the Timer Thermostat Expert or next to the battery on the inside Clever Thermostat PRO 3 Achosenname This name is used later to control the thermostat in your text message It cannot exceed 6 characters and cannot have spaces A thermostat in the living room can be called liver for example www icy connect nl 2 Add thermostat Add product code adress code Chosen name added The thermostat is chosen name successfully added and has the chosen name e g e g Add ICY3815 1234 liver liver added
3. your ICY 1 Chosen name 1 Connect The chosen names of the devices 2 Chosen name 2 are displayed with subsequent numbers 3 Chosen name 3 etc Retreive list of activated detectors Alert Type detector chosen name List with activated detectors Type of Type detector chosen name detector e g Frost alert This name e g is allocated by the device itself The Frost alert garage Power alert Chosen name is the name that you have electb assigned No code will be shown on The ICY Connect display 26 LCY B V Use Text Message operator commands When the telephones and devices are added you are ready to use the ICY Connect From the set telephone numbers you can operate the devices Below is a description of the commands Set thermostat With the ICY Connect you can set the temperature from all connected thermostats The temperature can only be set in whole degrees Set temperature Temp chosen name Temp chosen name set The termostat is gewenste temperatuur wanted temperature succesfully set on the chosen temperature In e g Temp liver 23 e g Temp liver set 23 this example 23 C a ae en You text message You receive text message Display ICY Connect optional T When you set the temperature via the ICY Connect you set it to mode Fixed Temperature Clever Thermostat PRO or Warm Welcome Timer The
4. Addition thermostat failed Thermostaat verwijderen You text message You receive text message Display ICY Connect optional Delete Thermostat Del Chosen name Chosen name deleted The thermostat is successfully deleted e g Del liver liver deleted Delete thermostat failed ZZ LCY B V Linking Devices Not only can you switch the thermostat on and off but with ICY Connect you can also switch on and off electrical appliances via text message Such a device must therefore be connected to an ICY Power Switch These are available at the store where you bought the ICY Connect For every device that you want to switch you will need a Power Switch Both Power Switches and thermostats can only be controlled via text message if they can be identified by ICY Connect To identify devices they should first be added This means that the device e g a lamp in the living room must be given a name that you will later use in a text message to turn it on or off Add device A device can only be added from the main number You will need 1 The product code e g ICY3512 2 The 4 digit address code that can be found on this product 3 A chosen name This name cannot exceed 6 characters and cannot have spaces A lamp in the bedroom for example can be named lampbe www icy connect nl Programming 23 Add device You text message You receiv
5. ICY Connect User manual and installation guide ICY4002IC A l LCY B V Introduction eee 5 Warranty ionikoa ernn no E EEEE EAA anid deb tu sssnsd nike 5 Overview ICY Connection aiee eee E E E E E TERS 7 PQ PA ACh ON aerosani ale ren on p inane teure 8 Installations ee ee A 8 Placingantennass ssnsarvaarsansersanrat bevamerennekenderandesds vernederd anna 8 Placing adapter PlUQ ccsecccsecce neces neces cece eeeeeeeeeaeeeeaeeeeaeeese ness essen es 9 Attach to the Wall wives een ee 10 Subscription choice and registration nnnnnnnenenenenneneneneneeneneneneen 11 Network guall check oaie reni EEEE EEA A 12 Programming nenna Ee eda ea 13 The structure of a text message nnee venen 13 Text messages YOU send sussen eonsensenneensenneensennvenvenneenvennenneenen 13 Text messages you To e Esera an n E E Ene EESE EET Siia 13 Linking telephones isasi E R A A 14 Set main number s asss nane arans secaestsestessosndadmesedasssaaenenesncans 15 Change mainnumber s nannten 16 Addsecondarynumberssaamsinssssssumoersnare sert merdsenrttinwinssnsaerskeardne ies 17 Delete secondary number sus ven sennvenvenneenvensennvenvenneenvenneenvenn 18 Setting reply MOSS ses mzsnetententeenteent dear lade a estat 19 Linking Thermostatic oia teeter aiaiai eir aie an oa aea Aaaa 21 Add thermostats orrs seven semens EE EEE E E ie 21 Delete ithermostat une nE EEEE ENERET EEEE REAREA 22 LINKING Devices ienr basesces ci
6. e lamp in the bedroom o aa zZ www icy connect nl Use 29 Activate deactivate detectors You can choose if you want to receive a text message if there is a fault Therefore you need to activate or deactivate the connected detectors This is only possible from the main number Activate deactivate detectors You text message You receive text message Display ICY Connect optional Alert chosen name on Alert chosen name activated The detector is succesfully activated e g Alert garage off e g Alert garage activated Alert chosen name off Alert chosen name deactivated The detector is succesfully deactivated H e g Alert garage off e g Alert garage deactivated a Failure to Activate deactivate If an alarm goes off ICY Connect sends a text message every half hour max 5 times a day depending on whether the fault has been solved or not After those 5 text messages the ICY Connect stops sending messages about that particular problem After 1 day this process is repeated if the problem persists or if the detector sends another fault message 30 LCY B V www icy connect nl 3 Codes on the display Meaning o O code LCY B V Technical Ini E Secondary number is being deleted Reply mode is being set Device is being switched on Tempera
7. e text message Display ICY Connect optional Add product code adress Chosen name added The device has been code chosen name successfully added and is named chosen e g e g name Add ICY3512 1234 lampbe lampbe added WERNE GE Be Delete device A device can only be deleted from the main number Delete device Del chosen name Chosen name deleted The device is successfully deleted e g DEL lampsbe N ae u a i 24 LCY B V Programming You can connect different reporting systems which are equipped with ICY Net to the ICY Connect You can add these in the same way as the other devices see page 23 Possible reporting systems include ICY Smoke heat detectors ICY Frost detectors ICY Power failure detectors ICY Pressure detectors ICY Door Window contacts Visit the website for more information www icy connect nl www icy connect nl 25 Retrieve set data At any given time you can ask for the set data by using the main number This way you can find out which telephones or devices have been added Retrieve programmed telephones 1 Main number The first number number 1 is the main 2 Secondary number 1 number The other numbers are the set 3 Secondary number 2 secondary numbers You text message Show phone etc Retreive set devices Show config sw 1 0 Sw stands for software version of
8. eive a telephone number You can choose from various text message packages Each package gives a certain number of text messages per month that ICY Connect can send to you This pertains to text messages that can be sent to you for example when retrieving the temperature in your home or when setting the thermostat For explanation of the various text messaging packages and arranging a subscription go to www icy connect nl There you will find more information about this procedure Make sure that your ICY Connect is switched on within 2 days of registering your subscription The SIMcard can only be activated by us if the ICY Connect is on Activation takes 2 to 7 working days Then you are given a telephone number for your ICY Connect As long as the SlMcard is not activated you will see Elon the display www icy connect nl Preparation Network quality check After receiving notification that your ICY Connect is activated you can see what the quality of your network is This shows up on the diaplay using 4 arrows TT UI I no range poor range reasonably good range full range good range If you have poor or no range then the ICY Connect has been mounted on the wrong place Try to find another location where you have good range coverage Do the same if after starting ES shows on the display If you choose a different location you have to wait at least 5 minutes to see whether the range is better at
9. er you have to delete the old number After that add a new main number as described on page 15 The main number can be deleted from the main number itself or from a secondary number This is in relation to possible loss of the telephone with the main number The main number can only be changed by using the PINcode from ICY Connect Delete main number Phone phone number del pincode Phone deleted Telephone number is successfully e g phone 31612345678 del 12 deleted Telephone number failed to delete EE EL correct eg ees If you do not remember the code you can send a text message to ICY Connect without the PINcode as shown here If your reply mode see page 19 is on you will recieve a text message stating Use Code After ICY Connect has processed the text message the i 16 LCY B V Programming PINcode is shown for 30 seconds on the ICY Connect display If the reply mode is on off you will still be able to read the code from the display but you will not receive a text message Request PINcode You text message You receive text message Display ICY Connect optional Phone phone number del Use code Read the code that shows on E the ICY Connect display g Add secondary number Four telephone numbers can be set as a secondary number This can only be done from the main number Add secondary number You text message You receive text
10. ese numbers have to begin with 316 or 06 Main Number There is one telephone number that can be set as the main number The telephone with this number is used to program and to receive error or malfunction messages In addition you can use this phone to operate devices Secondary telephone numbers can only be added by using this telephone Secondary numbers Up to four telephone numbers can be added as secondary numbers From these four numbers you can only operate ICY Connect ATTENTION We recommend to program at least one secondary number in case you loose your telephone with the main number LCY B V gt Programming Set main number When the subscription is activated without a main number being programmed the ICY Connect display will give a 2 digit PINcode for example JE Write down this code somewhere e g on page 35 of this manual and save it properly This PINcode is required if you at a later time want to change the main number The main number can be set by text messaging the word phone and the Pincode to ICY Connect s telephone number You do this from the telephone that you want to use as your main phone You do not have to text message the telephone number of your own telephone Set main number Phone pincode Phone added Telephone number is successfully added e g Phone 12 www icy connect nl 15 Change main number In order to add a new main numb
11. inisee ian EE KAE a PAORS EEI 23 AAG device AENEA OEE A AA AANE 23 Delete d vites nibere erinan einen 24 www icy connect nl Link aestsctors annet Baker inkl 25 Retrieve set data ee een 26 Text message operator commands nennen ennen Setting thermostat ussen seonsaenerenrsrers ern Temperature retrieval Switch devices Activate deactivate alarms enen on onevereneenenenenenen evene vernenenenen Technical information cccccccesccsssesccessesecesccsesssecsesssecssseseesrees 32 Codes onthe displays spe aneen a ea ea Ea ea ET EKS 32 Table with personal settings nnen ennen 34 LCY B V Introduction Congratulations on your purchase of the ICY Connect Thanks to ICY Connect you can use a simple text message to turn on and off your heating and other appliances in and around your home Wherever you are The ICY Connect is designed for applications in and around homes and vacation houses and can be used in combination with ICY wireless devices Error messages and faults can be quickly transmitted via text message There is a 2 year warranty after purchace of the ICY Connect This warranty is void if the covering housing is removed For further provisions relating to the warranty please check the general terms on our website www icy connect nl 5 a 7 CY BY Overview ICY Connect In doelen Antenna Clips from screw holes for wall mounting
12. message Display ICY Connect optional Phone phone number add Phone added Telephone number is successfully added Telephone number failed to add The confirmation text message is sent to the added number Should an error occur you will receive a message on the main number www icy connect nl 17 Delete secondary number Secondary numbers can only be deleted by the main number If you have reply mode see page 19 on on you receive a confirmation on the main number Delete secondary number You text message You receive text message Display ICY Connect optional Phone phone number del Phone deleted Telephone number is successfully deleted Telephone number failed to delete 18 LCY B V Setting reply mode You can choose to receive confirmation text messages after each setting change In the tables this is indicated by the word optional after you receive text message You set this by setting the reply mode on on Normally the reply mode is on off You have a set number of text messages per month How many depends on which subscription you have At the end of every message you get to see how many text messages have been sent to you this month If it appears that you need more text messages than your subscription allows you can at any time upgrade your subscription via your account on our website If you do not want to do this you
13. rmostat Expert The device maintains this mode until the thermostat is manually used again Only the Timer www icy connect nl 27 Thermostat deactivates Warm Welcome automatically after 48 hours This is not the case by the Clever Thermostat PRO Temperature retrieval Regardless of the reply mode see page 19 you can always ask for the temperature which is measured at that moment by a connected thermostat Temperature retrieval Temp Chosen name Temp chosen name actual Shows what the current temperature gt set temperature and set temperature is on the termostat e g Temp liver e g Temp liver 20 C gt 23 C Failure of requesting the temperature 28 LCY B V Switching devices Different ICY products can be connected to the ICY Connect This way they can be programmed by text message See our website for more information about these products Below is an explanation of how these devices can be switched Switching devices You text message You receive text message Display ICY Connect optional Switch chosen name on Chosen name switched on Device is successfully activated In this example e g switch lampbe on e g lampbe switched on the lamp in the bedroom Switch Chosen name off gekozen switched off Device is successfully deactivated In this e g switch lampbe off e g lampbe switched off example th
14. this location If there is no room in the house with good range then you need an alternative antenna More information about this can be found on our website LCY B V The structure of a text message Text messages you send To program and operate ICY Connect you have to send text messages with commands to the assigned phone number The commands can be found in the following chapters There is a table provided that tells you what the structure of the text message is Bold text commands for the ICY Connect Italic text numbers codes or names that you must enter The words are not upper case sensitive There always has to be a space between commands names and codes You can send a maximum of 1 message per minute Text messages you receive Text messages you receive from ICY Connect always end with the number of text messages already sent to you in that month For example 12 20 at the end of a message means that you have a subscription for 20 text messages per month and that you have received 12 When your text message credit is used up ICY Connect cannot send you any more messages in that month You can of course still send commands to ICY Connect www icy connect nl Programming Linking Telephones Before you can operate ICY Connect you have to program which telephones may be allowed to use your ICY Connect ICY Connect can only be used and operated by Dutch telephone numbers that you have programmed Th
15. ture is being set www icy connect nl 33 Table with personal settings e g Clever Thermostat PRO e g ICY3815 34 LCY B V Hulptabel met uw instellingen Pincode Chosen name max 6 characters www icy connect nl 25 For technical questions and support service icy connect nl 1 C Y B V 2011 changes reserved Revision 2011 1 36
Download Pdf Manuals
Related Search