user manual for gsm quad-band audio transmitter pixel full fw v1.9 or
Contents
1. HOURS 20 gt 9 WHEN THE MESSAGE IS DECODED THE UNIT WILL SHUTDOWN IMMDIATELY IF IT IS DISCONNECTED FROM THE POWER THE NEXT TIME IT WILL RECONNECTED IT SEEMS IT DOESN T WORK OR IT IS BURNED ALSO THE LED WILL NOT WORK SO DONT CONFUSE A SLEEPING UNIT WITH A BURNED OR DON T WORKING UNIT WAIT THAT THE SLEEPING TIME WILL END LEAVING THE UNIT CONNECTED TO THE POWER LEDO LED1 TIMEOUT RECALL IF THE CALL END ABNORMALLY THE UNIT WILL WAIT THIS TIME BEFORE TRY AGAIN TO RECALL THE TARGET NUMBER xx 00 gt 99 MINUTES xx 01 DEFAULT THE LED IS ALWAYS OFF THE LED 15 IN NORMAL WORKING CONDITION WITH VARIOUS DIAGNOSTIC LAPMS DEFAULT DISABLE ALL THE RECALL FUNCTIONALITY WITHOUT DISABLE THE PROGRAMMED NUMBERS VOICE COMMANDS HHTVXX H V OLX HHVOXX VOICE TIMEOUT AFTER ACTIVATION EVENT IS ENDED MOVMENT AND OR AUDIO NOISE xx 01 gt 98 MINUTES xx 05 DEFAULT MICROPHONE SENSIVITY X 0 gt 6 MINIMUM GAIN AT 12db 0 GAIN AT 8dB 1 GAIN AT 4dB DEFAULT 2 GAIN AT 088 3 x 4 GAIN AT 4dB x 5 GAIN AT 8dB MAXIMUM GAIN AT 12dB 6 ENABLE THE SHOCK SENSOR AND SET THE MOTION SENSIVITY x 0 gt 9 FUNCTION DISABLE DEFAULT 0 LOW SENSIVITY ALONG AND DURABLE MOVMENT IS NECESSARY 1 TO TRIGGER THE UNIT HIGH SENSIVITY ALITTLE MOVMENT IS ENOUGH TRIGGER 9 THE UNIT IT S POSS2. SPECIFIC SMS COMMAND ARE SHOWN THE DEFAULT VALUES D1 REQUEST THE STATUS OF THE INFORMATION DESCRIBED AT THE PAG 4 OF THIS MANUAL KIND OF UNIT NAME VERSION FW 1 WNMov NON PROG NStop NON PROG NVoce NON PROG NEntr NON PROG HNCell NON PROG 02 REQUEST THE STATUS THE INFORMATION DESCRIBED THE 6 OF THIS MANUAL KIND OF UNIT NAME VERSION FW D2 0 VOX 0 RAN TV 05 TR 01 TAV 00 D3 REQUEST THE STATUS OF THE INFORMATION DESCRIBED AT THE PAG 5 6 7 OF THIS MANUAL KIND OF UNIT NAME VERSION FW 3 HLED 1 HVOL 2 DSP 1 ECHO 0 0 0 CONN_V 0 SIGN xx BATTERY 3 5V IMEI 01234567890123 04 REQUEST THE STATUS OF THE MAIN CELL ID KIND OF UNIT NAME VERSION FW 4 MAIN CELL MCC xxx MNC x LAC xxxxx CID xxxxx SIGN xx BER xx 05 REQUEST OF CELL ID FROM ALL REGISTRERED NETWORK COMPANY WARNING THIS COMMAND MAY TAKE UP TO 5 MINUTES TO EXECUTED DURING THIS TIME THE PIXEL WILL BE NOT REGISTRERED AND WILL BE BUSY AT LEAST 9 CELL ID WILL BE LOGGED DA REQUEST ALL THE PREVOIUS STATUS MODE LISTED AT THE SAME TIME EXCEPT THE D5 COMMAND GENERAL NOTE USE THE D1 COMMAND FOR KNOW THE TYPE OF PIXEL UNIT PIXEL FULL PIXEL LIGHT THESE ARE TWO TYPICALLY OPERATIVE MODE OF PIXEL A PIXEL FULL V1 9 D1 PIXEL FULL 2 MICROPHONE FIRMWARE VER 1 9 A
3. WITH SPECIFIC DELAY WE PROVIDE SPECIFIC LOCALIZATION SOFTWARE WITH AN EXTENSION THAT READ THIS INFORMATION AND USING PUBBLIC CELL ID DATABASE LOCALIZE THE PIXEL UNIT TO DO SO IS NECESSARY PROVIDE AN INTERNET CONNECTION AND A GSM MODEM CONNECTED TO THE PERSONAL COMPUTER THAT RUN THE APPLICATION ALL THE CELL ID DATA AND THE LOCALIZATION INFORMATION WILL BE STORED INA SPECIFIC SQL DATABASE AND MAY BE REVIEWED LATER TO ANALIZE THE ROUTE DONE FROM THE UNIT PLEASE ASK US FOR THE FULL IMPLEMENTATION OF THI EXTENSION AND FOR THE SOFTWARE PREREQUISITIES TO ENABLE THIS FUNCTIONALITY YOU WILL USE THE FOLLWING COMMANDS NCxxx SET THE CELL ID TRACKING NUMBER FOT THE OUTGOING SMS THIS NUMBER CORRESPONDS AT THE SIM INSIDE IN THE MODEM CONNECTED TO THE PC NO THE PC WILL BE ALREADY INSTALLED OUR SOFTWARE FOR TRACKING THE UNIT THE UNIT SENDS THE CONTINUOUS LOCALIZATION CELL ID SMS MESSAGES IF CONFIGURED WITH DELAY OF MINUTES INDICATED IN THIS SETTING XX 00 FUNCTIONS DISABLE DEFAULT XX 01 gt 99 MINUTES 05 REQUEST OF CELL ID FROM ALL THE AVAIABLE NETWORK COMPANY WARNING THIS COMMAND MAY TAKE UP TO 5 MINUTES TO EXECUTED DURING THIS TIME THE PIXEL WILL BE NOT REGISTRERED AND WILL BE BUSY AT LEAST 9 CELL ID WILL BE LOGGED e REMOTE DEBUG MESSAGES WITH THIS COMMANDS YOU CAN GET THE STATUS OF THE UNIT THROUGH SMS MESSAGES THE DEBUG MESSAGES ARE SENT BACK TO THE PHONE NUMBER THAT ASK FOR THEM WITH THE
4. independently selectable microphones at the same time pseudo stereo or with dynamic mic option Two different solutions 7 26 Vdc external stabilized trough an high efficiently switching power regulator 3 6 direct for hi lion battery direct connection in sleep and at maximum audio level transmission 3 6 Vdc 13mA sleep 140 max 12 Vdc 35mA sleep 75 max Two selectable microphones both or independently flexible patch Power supply with red and black cable Microphones cables with anti tear steel core and double shielding Operating status led Variable shock sensor sensivity and vox threshold level 20 gr approximately 31x 31 x 6 mm
5. ATED WITH THE SPECIFIC FUNCTION SET THE NUMBER WITH THE INTERNATIONAL PREFIX EX 39 33 44 NExxx SET THE INCOMING NUMBER IF SET THE UNIT WILL ACCEPT ONLY CALL FROM THE PROGRAMMED NUMBER NVxxx SET THE VOICE OUTGOING NUMBER THE UNIT WILL CALL THIS NUMBER IF APHYSICAL MOTION IS MEASURED OR IF ENABLED IF THE VOX LEVEL IS REACHED NMxxx SET THE START VEHICLE NUMBER FOR THE SMS ALARM NSxxx SET THE STOP VEHICLE NUMBER FOR THE SMS ALARM H NCxxx SET THE CELL ID TRACKING NUMBER FOR THE OUTGOING SMS Ex xxx PHONE NUMBER 441231234567 HHNV 441231234567 SET THE VOICE NUMBER TO DISABLE A SPECIFIC FUNCTION YOU WILL SEND 5 ZEROS AS NUMBER TO THE SPECIFIC NUMBER COMMAND YOU WANT DISABLE EX NV00000 FOR DISABLE THE VOICE NUMBER IMPORTANT NOTE REMEMBER ALWAYS TO SEND AN ASTERISK AT THE END OF THE NUMBER GENERAL FUNCTIONS H RESET BONX CLEAR AND DELETE ALL THE USER PROGRAMMED FUNCTION AND SET THE UNIT IN TO THE FACTORY RESET STATE THE UNIT WILL ALSO DO AN HARDWARE AND SOFTWARE RESET THE UNIT WILL DO AN HARDWARE AND SOFTWARE RESET WITHOUT LOOSING THE USER PROGRAMMED FUNCTION THE UNIT WILL GO IN TO THE SLEEP MODE FOR THE TIME LISTED IN THE FOLLOWING TABLE 1 lt 15 MINUTES 2 gt 30 MINUTES gt 60 MINUTES 4 gt 90 MINUTES 5 lt 2 HOURS HOURS 4 gt 6 x 7 gt 8 HOURS HOURS 16 gt 8
6. IBLE TO BE USED TOGETHER WITH THE VOXx FUNCTION ENABLE THE VOX SENSOR AND SET THE VOX LEVEL x 0 gt 9 FUNCTION DISABLE DEFAULT 0 LOW SENSIVITY AN HIGH AND DURABLE NOISE IS NECESSARY 1 TO TRIGGER THE UNIT HIGH SENSIVITY VOX IS ENOUGHT A LITTLE NOISE TO TIGGER 9 THE UNIT IT S POSSIBLE TO BE USED TOGETHER WITH THE MOVx FUNCTION 5 HERAV MICROPHONE SELECTION x 0 gt 4 x 0 ENABLE MIC1 MIC2 AT THE SAME TIME DEFAULT x 1 ENABLE MIC1 x 2 ENABLE MIC2 x 3 DYNAMIC1 ENABLE MIC1 IF THE CAR IS STOPPED AND AUTOMATICALLY ENABLE MIC2 IF IT S MOVING x 4 DYNAMIC2 ENABLE MIC2 IF THE IS STOPPED AND AUTOMATICALLYENABLE MIC1 IF IT S MOVING ENABLE DSP PARAMETER NOISE REDUCTION OPTION x 0 gt 3 FUNCTION DISABLED DEFAULT 0 1 ENABLE THE SELF ADAPTIVE NOISE REDUCTION MODE 2 ENABLE THE NOISE WILL BE REDUCED OF 6dB ENABLE THE NOISE WILL BE REDUCED 12dB 3 ENABLE ECHO REDUCTION PARAMETER x 0 gt 7 x 0 FUNCTION DISABLED DEFAULT x 1 FUNCTION ENABLE WITH SOFT REDUCTION ECHO x 7 FUNCTION ENABLE WITH HARD REDUCTION ECHO IMMEDIATELY START ONE VOICE RECALL ON THE PRE PROGRAMMED VOICE NUMBER ENABLE THE VOICE RECALL ON MOTION VOX EVENT THIS FUNCTION MUST BE ENABLED FOR USE THE MOV VOX TRIGGER OPTION TRACKING CELL ID SMS COMMANDS THIS FUNCTION WILL ENBLE THE CONTINUOS SEND OF CELL ID SMS
7. PIXEL LIGHT V1 9 D1 PIXEL LIGHT 1 MICROPHONE FIRMWARE VER 1 9 WITH THE REMOTE COMMAND D3 YOU CAN SEE THE V x VALUE CONN V 0 MEANS THAT THERE IS VOICE CALL IN PROGRESS V 1 MEANS THAT THERE IS A VOICE CALL IN PROGRESS WITH THE REMOTE COMMAND D3 YOU CAN SEE THE SIGN VALUE WHERE GSM SIGNAL LEVEL xx 05 NOT GOOD SIGNAL MIN VALUE xx 30 VERY GOOD SIGNAL MAX VALUE FOR THE USE OF PIXEL UNIT IN CAR ARE RECOMMENDED THE FOLLOWING SETTING COMMANDS ECHO 1 VOL2 1 ATTENTION FOR THE USE OF PIXEL UNIT IN HOUSE OR OFFICE ARE RECOMMENDED THE FOLLOWING SETTING COMMANDS HHECHO 1 VOL6 DSP0 OR 1 WITH THE D5 DEBUG MESSAGE YOU CAN SEE ALL THE OTHER SECONDARY CELL THAT THE PIXEL IS LISTENING OF ALL THE OPERATOR AVAILABLE TECHINICAL SPECIFICATIONS GSM SECTION GSM BAND RF POWER SIM SMS AUDIO SECTION VOX FUNCTION DSP OPTION MICROPHONE SELECTION SECTION TRANSMITTER POWER SUPPLY CONSUMPTION MICROPHONES GSM ANTENNA CONNECTIONS OPERATING STATES SENSORS PARAMETERS WEIGHT DIMENSIONS Quad Band GSM 850 900 1800 1900 MHz 2W Class 4 8508900 MHz 1W Class 1 1800 amp 1900 MHz Sensibility GSM GPRS lt 106 dBm slide SIM card reader Text Switchable VOX with several levels Different noise reduction levels adaptive or fixed value reduction Two
8. USER MANUAL FOR GSM QUAD BAND AUDIO TRANSMITTER PIXEL FULL FW V1 9 OR GREATER Release Data June 2012 Version 1 3 This technical manual introduces the users at the correct use of audio GSM transmitter PIXEL FULL V 1 9 First of all check this simple four steps before insert the SIM in to PIXEL FULL Using standard mobile phone Disable the PIN request on the SIM that you want use Upon request the unit can be programmed in advance with pin code Remove the conference call call transfer and any other answering service prepaid SIM check the credit it multi numbering SIM voice data and fax use always the voice number as target for sending the SMS Send the SMS command following the instructions below all the command MUST be sent with uppercase characters Wait about 20 seconds between one SMS and each other giving the network the right time to deliver the message and the time to the PIXEL unit to decode respond and delete At the same time PIXEL will do series of led flashes to indicate that the message has been received interpreted and cancelled INDEX NUMBER SETUP VOICE SMS GENERAL FUNCTIONS VOICE COMMANDS TRACKING CELL ID SMS COMMANDS REMOTE DEBUG MESSAGES GENERAL NOTE TECHINICAL SPECIFICATIONS pag 4 pag 5 pag 6 pag 8 pag 9 pag 10 pag 11 NUMBER SETUP VOICE SMS THIS COMMAND SET THE PHONE NUMBERS CORREL
Download Pdf Manuals
Related Search