Home

EM-system-user-manua..

1. 5 This is the LBD indicator to receive signals in channel II When it s bright the digital displaying value is the value of receiving signal in channel II 6 This is the LBD indicator to receive alarm reference value in channel II When it s bright the digital displaying value is the receiving alarm reference value in channel II 7 This is the location LBD indicator in channel II When it s bright the digital displaying value is the location indicating value of channel II This value is the less the better 8 Insignificance 9 This is a four numeral display 10 This is a displaying window 11 This is the LBD indicator to receive alarm of channel I When it s bright channel I receives alarms 12 This is the interference LBD indicator of channel I When it s bright the channel I is closed off and the alarms will be invalid 13 This is the LBD indicator to receive alarm of channel II When it s bright channel II receives alarms 14 This is the interference LBD indicator of channel II When it s bright the channel II is closed off and the alarms will be invalid 15 Select button Press select button the red LBDs in the displaying window will be lighted one by one and the digital display will show the corresponding values with those red LBDs one by one 16 Increase button Press select button to make the receiving alarm reference value LBD indicator be lighted in the displaying window of channel I and the
2. connecting wire receiving wire transmitting wire ogoo0g mid transnuttns receiing2 T60Sving 1 Wansuutting iney online Onine 3 select o increase reduce store Picture 3 http www dragon guard com 5 4 Regulating picture of detecting doors Picture 4 5 Matching board of transmitting antenna 1 a Picture 5 1 Transmitting ports http www dragon guard com F transmitting coil F transmitting coil GND receiving transmitting yellow wire blue wire f receiving transmitting red wire black wire all those above have been connected very well when they were in our factory so it s not necessary for clients to connect them X1 counter signal yellow wire 5v counter power red wire GND counter earth wire those have been connected very well when they were in our factory Those are only used for the counting function 2 Port of light wire has been connected very well when they were in our factory 3 4 Connecting ports of light wires and receiving doors connect any one of the two ports with the light wire port of the receiving antenna matching board Users should connect them correspondingly by themselves 5 Matching board of receiving antenna v v 4 3 Picture 6 1 Receiving ports J receiving coil blue wire J receiving coil black wire GND yellow receiving wire J red receiving wire Ov blue light wire 12v red light
3. them to deposit their bags If they don t want to deposit the bags pay more attention to them if everything is fine and the system alarms when they go out we could not deal with it 3 If the system alarms when the customers are passing the channels you could let them pass again to make sure about the alarms and at the same time you could explain that doing this is good for them with the posters in your market to let the customers receipt this gladly 4 There will always be some misreport and blind spots in the anti systems no matter how advanced they are So we need a new concept to understand their function correctly what we want is a good environment and a minimum loss rate rather than the number of thieves 5 We could reduce the strip loss and improve the environment largely by scientific management http www dragon guard com 13
4. EM DGES Digital Monitoring System Read carefully before using DRAGON GUARD Manual 3 goaa DELENN http www dragon guard com k Instruction of DGES Digital Monitoring System A Using and principle of DGES system This anti thief system is composed mainly by detecting doors and monitor host and EM deactivator reactivator and EM strip check equipment and degaussing board and tags and detachers and EM strips and so on 1 Detecting doors 2 or 3 or more detecting doors compose the single channel or multiple channels at the gate with transmitting and receiving coils inside the doors 2 Monitor host connected with detecting doors by special leads When the commodities with EM strips inside go into the channel the normal electromagnetic shape will change when the host finds that the system will alarm immediately 3 EM deactivator reactivator cashiers should degauss the commodities by EM deactivator reactivator or degaussing board after the payment It is usually put beside the cashier counters for convenient use 4 EM strips there are two kinds of EM strips permanent strips and composite strips You could choose one type according to your requirements Permanent strips could be magnetized or degaussed by EM deactivator reactivator Permanent strips do not have this function 5 EM strip check equipment it is used to checking if there is an EM strip inside the book B Graphic appearance http www
5. com 11 slogans at the entries such as there are anti thief systems in our shop please cooperate with them and at the exits such as please go to the counters for payment 2 How to avoid disputes when found some suspects Many domestic and foreign experiments have proved that anti thief system could stop about 80 90 stealing but workers and administrators should understand that the function of the anti thief system is to alarm thieves psychologically to make them give up stealing rather than a special tool for catching thieves and at the same time the system could improve the shopping atmosphere which is different from the old watching way to offer the best respect to more cultured people so we should have a faith on we would prefer to miss 10 thieves instead of catching a wrong person Under the alarming situation we should think it s misreporting first and let the customers cooperate to walk back and forth again if the system doesn t alarm this time do apologize to the customers and if the system still alarms we should say to the customers like this sir miss have you forgotten some procedures It s ok please do it again If he she has some commodities really without normal checking deal with it according to your tradition Few large metal objects such as porcelain enamels and umbrellas will cause misreporting if they are too close to the doors Few cell phones and cameras and VCD machines could also cause mi
6. dragon guard com 2 1 Host back panel picture and function introduction fe zZ OFF online 3 online 2 AC 220V online 1 transmitting receiving 1 receiving 2 Picture 1 1 220V AC outlet with spare fuses inside 2 Power switch Make it be ON host works make it be OFF host stops working 3 4 5 Online interfaces 6 Input interface of transmitting antenna Three chip air plug or five chip air plug 7 Input interface 1 of receiving antenna Four chip air plug 8 Input interface 2 of receiving antenna Four chip air plug 2 Host front panel picture and function introduction 9 1 21 5 6 12 1 15 a O Lo PCHA OH I select paglia os eet E se Q increase reduce store re ane 87 B 14 16 17 Picture 2 1 This is the LBD indicator to receive signals in channel http www dragon guard com I When it s bright the digital displaying 18 value is the value of receiving signal in channel 2 This is the LBD indicator to receive alarm reference value in channel I When it s bright the digital displaying value is the receiving alarm reference value in channel I 3 This is the location LBD indicator in channel I When it s bright the digital displaying value is the location indicating value of channel I This value is the less the better 4 Insignificance
7. e followed steps when the equipments cannot work normally If they still cannot work normally please contact us Common Faults Reasons and eliminations Continuous misreporting 1 Are there some EM strips or books and other objects that have strips inside around the detecting doors 2 There are large metals and umbrellas and metal cups and metal bowls and other metal objects next to them closely 3 The system signal value is a little higher The normal value should be less than 0020 Regulate detecting doors to let the signal value go back to normal 4 Setting reference is a little lower which should be 20 30 more than signal value 5 There are beams or wires beside the detecting doors or at the bottom of them 6 Detecting doors are next to the computer monitors closely Do not alarm 1 Setting reference value is too high 2 Interference indicator was light and the signal value was negative regulate the detecting doors 3 Connecting wires was broken host signal value showed no change 4 EM strips was not magnetized enough or they were broken 5 Detecting doors are next to the computer monitors closely Host does not work 1 Power outlets contact badly 2 The fuse is broken change a new one G Advices for administrators 1 Paste some notifications at the observable places For example paste some http www dragon guard
8. he signal value of receiving 2 When there are some strips passing the detecting channel 2 this signal value will change that means channel 2 works very well Press select button then to let the second red indicator be lightened in the right of the display window then the panel will show the reference value of channel II that need setting The setting way is the same with then channel 7 Hole an EM strip Let the strip be parallel with the ground and be vertical with the passing direction When the strip is passing the channel the alarm indicator on the receiving 1 will give a light sound alarm At the same time the 11 red light picture 2 on the right of the host panel will give a light sound alarm the signal value then must be higher than the setting reference value When the strip is passing the channel 2 the alarm light on receiving 2 will give a light sound alarm which is different from the channel I for easy distinguishing and at the same time the red light 13 picture 3 on the right of the host panel will light 8 Note the location of the detecting door by pencil and prepare for expansion screws Set the detecting doors on the screws Do not fix the screws and redo the 6 7 steps Tighten the screws after normal working The system setting and regulation is finished http www dragon guard com 9 D Main technical parameters Channel width single channel 700mm 1000mm double channel 1400mm 2000mm Detecting height 160 mm P
9. lready on 6 Left right or forwards backwards lightly move the two receiving doors respectively according to the regulating way in picture 4 to let the two green lights 11 13 be extinguished respectively showed in picture 2 Press select button to let the first red indicator be lightened at the left I of the panel displaying window then the display in the panel is the signal value of receiving 1 When the EM strips are passing the detecting channel 1 if the signal value changes that means the channel 1 works http www dragon guard com 8 very well Press select button then to let the second red indicator in the left of the displaying window to be lightened the displaying number in the panel is the reference value that need setting and the value will be increased if you press the increase button and the value will be reduced if you press the reduce button Press the two buttons continually to achieve the reference value the system needs we advise you to set the value 30 higher than the static value which showed when there is no EM strips or other objects passing the detecting channels Press store button to store the certain reference value Attention the users should press the store button after every regulation or the system will memorize last value The data will no be lost if the power is cut off Press select button to let the first red indicator be lightened in the right of panel display window then the display number in the panel is t
10. n press increase button the displaying value in the window will be increased and what is being increased is receiving alarm reference of channel I Press Select button to make the receiving alarm reference value LBD indicator be lighted in the displaying window of channel II and then press increase button the displaying value in the window will be increased and what http www dragon guard com 4 is being increased is receiving alarm reference of channel II 17 Reduce button Press select button to make the receiving alarm reference value LBD indicator be lighted in the displaying window of channel I and then press reduce button the displaying value in the window will be reduced and what is being reduced is receiving alarm reference of channel I Press select button to make the receiving alarm reference value LBD indicator be lighted in the displaying window of channel II and then press reduce button the displaying value in the window will be reduced and what is being reduced is receiving alarm reference of channel II 18 Store button If the receiving alarm reference value has been regulated press this button to store present receiving alarm reference value of channel I and no matter the system is ON or OFF that value would be sustained as long as no contact on increase button or reduce button The channel II is in the same way 3 System connecting picture receiving transmitting receiving 2 light wire light wire receiving
11. ower 220V 10 50Hz Output power lt 13W Working environment 10 c 40 c Continuous working hours not less than 24 hours E Attention 1 There should not be large metal objects or metal guardrails that may damage the magnetic field around the detecting doors in the range of 80cm and the books or other commodities should no be put in the range of 80 cm around the detecting doors 2 Host should be far away from the detecting doors at least 2m Computers should not be next to the detecting doors closely They had better not be on the same axis The detecting doors should be far away from the computers at least 2m 3 Catch hold of the air plugs instead of pulling the wires overexerted for fear that the wires will be broken when removing or installing the wires 4 Do not move the detecting doors with hands usually for fear that the setting location will be influenced 5 Do avoid trampling or heavy pressure on the wires directly for fear wires broken or short circuits 6 Do not turn on and turn off usually for fear host damage 7 Do turn off the power when replace the fuse You had better insert the host plug into a dependent outlet and do not share the outlet with other equipments This outlet should be earthed very well 8 Setting of detecting doors should avoid the large cement pillars and beams and other wires http www dragon guard com 10 F Elimination of faults and interference Eliminate the faults according to th
12. sreporting So pay attention to these situations when the system alarms In rare cases it s hard to find some thieves who can hide commodities so perfect that nobody can find that we have to let them go for fear catching wrong persons In fact this loss can be equalized because we always have a policy that the thieves should pay 10 times the price for the commodities they steal We should believe that though we have some loss thieves obtained some education or alarm through this system and they may not make such mistakes again easily this is a good contribution for society 3 Assign 1 2 administrators for anti system specially We will train them when setting and regulating the system and they will be responsible for repair reporting with us later http www dragon guard com 12 H Using skills of anti thief system Many merchants have found and concluded a series of using experience and skills for anti system with the expansion of its use There are some typical situations for users 1 To judge if there are some misreporting users could follow the next steps 1 Your commodities are not degaussed enough 2 There are some commodities that are in other shops are not degaussed enough 3 There are large porcelain cups or bowls 4 There are iron long umbrellas 5 There are large metal objects on the backpacks 2 If the system alarms when some customers are passing the detecting channels to get in you could ask
13. wire those have been connected very well when they were http www dragon guard com 7 in our factory 2 Receiving interface the users should connect the interface between the receiving 1 and receiving 2 This is only used to double channels system 3 Buzzer interface it has been connected very well when they were in our factory 4 5K potentiometer the alarm sound will be louder if you regulate it clockwise and the alarm sound will be lower if you regulate it counterclockwise 5 Counter interface it s an interface between the transmitting door and the counter it is only used for counting function The user should connect it very well 6 The port of counting wires 5v red counting wire X yellow counting wire GND blue counting wire they are connected very well when they were in our factory C Setting and regulation of system 1 Set the detecting doors in the same direction according to the serial number on the motherboard 2 Connect the leading wires at the bottom of the detecting doors in turns of the way in picture 3 3 The power of the host should be earthed very well and should be at least 2m far away from the detecting doors 4 There should not be large metal things around the detecting doors in the range of 80cm 5 Connect the host with the power and turn on the power the power is at the back panel of the mainframe case as in picture 1 Then the window will display red numbers to show that the power is a

EM-system-user-manua..

Contents

Download Pdf Manuals

Related Search

Related Contents