NX-1815E NetworX Voice Keypad with 16 zone LEDs User Manual
Contents
1. Enter your Master pin code 3 2 Selects communicator test 4 MENU Moves back to system test menu step 3 5 MENU Exits back to main menu 6 MENU Press menu to exit Step How to Perform a battery test 1 MENU 4 Selects main menu Option 4 System Test 2 Enter your Master pin code 3 3 Selects battery test 4 MENU Moves back to system test menu step 3 5 MENU Exits back to main menu 6 MENU Press menu to exit Step How to Perform a zone walk test 1 MENU 4 Selects main menu Option 4 System Test 2 Enter your Master pin code 3 4 Selects zone walk test Activate all detection devices by walking within the field of view of 4 R motion sensors and opening and closing all protected windows and doors 5 STATUS Press status to review tested zones 6 MENU Moves back to system test menu step 3 7 MENU Exits back to main menu 8 MENU Press menu to exit NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 15 User Configuration Menu 5 Menu 5 User Configuration 1 User PIN 2 User Partition 3 User Authority The user configuration menu is where user authority levels PIN codes and partitions are assigned to users of your security system User PIN This is the code used to arm and disarm partitions within your security system They are generally four digits in length but can be configured by your service provider to be six2. Press menu to exit How to Configure set up partition control for a specific user Step Example Configure control of partition 2 for user 4 1 MENU 5 Selects main menu Option 5 User configuration 2 Enter your Master pin code 3 2 Selects to configure user partition 4 4 ENTER Selects user 4 Selects partition 2 5 2 Note Pressing enter will announce the partitions available for this user and the zone lights will indicate selected partitions 6 MENU Moves back to user configuration step 3 7 MENU Exits back to main menu 8 MENU Press menu to exit How to Configure Authority levels for a specific user Step Example Change user 6 to a master code 1 MENU 5 Selects main menu Option 5 User configuration 2 7 7 Enter your Master pin code 3 3 Selects to configure user authority 4 6 ENTER Selects user 6 5 4 Selects option 4 master code authority see Table 1 below Note Zone lights will indicate selected authority options 6 MENU Moves back to user configuration step 3 7 MENU Exits back to main menu 8 MENU Press menu to exit Table 1 User Authority Options 1 2 3 4 Reserved Arm Only Arm only after close window Master code authority Arm disarm code Allowed to bypass zones User code will send open close reports oOo N DO O Must be off NX 1815E NetworX Voice Keypad wi
3. Outputs Where external devices are configured These devices can be controlled from your security system Perimeter The outer edge of the protected partition i e doors and windows Quick Arm An option that allows you to turn on ARM the security system by touching the AWAY Self Monitored A security system that is programmed to send alarm signals to a private phone number Not all features are available with a self monitored system Stay Mode To turn your security system on when you are staying in the premises this will automatically bypass pre programmed zones and arm others Mainly utilized for arming just the perimeter of the premises Service The installation maintenance company servicing your security system Provider User Code A four 4 or six 6 digit pin code that is used by a user to arm or disarm the security system Also can be used as a function code for certain features Note A system may have either four 4 digit pin codes or six 6 digit pin codes but not a mixture of both Zone Location on your security system where a detection device is connected 6 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual The NX 1815E Partition Zone lights Control keys gt Numeric touchpad Microphone Legend Vital visual information for you to review 2 Press the corresponding number on the keypad AWAY Press the corresponding key on the keypad Press the corresponding number on
4. NX 1815E Networx Voice Keypad with 16 zone LEDs User Manual P N 230248 REV C ISS 18JUL14 Copyright Trademarks and patents Manufacturer FCC compliance NFPA 72 EU compliance EU directives a Contact information Customer support 2014 UTC Fire amp Security Americas Corporation Inc All rights reserved This document may not be copied in whole or in part or otherwise reproduced without prior written consent from UTC Fire amp Security Americas Corporation Inc except where specifically permitted under US and international copyright law The NX 1815E name and logo are trademarks of UTC Fire amp Security Americas Corporation Inc Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products Placed on the market by UTC Fire amp Security Americas Corporation Inc 3211 Progress Drive Lincolnton NC 28092 USA Authorized EU manufacturing representative UTC Fire amp Security B V Kelvinstraat 7 6003 DH Weert Netherlands This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accor
5. 9 Selects main menu Option 9 Basic system configuration 2 Selects partition entry time 3 Selects partition exit time 7 Enter your Master user pin code 1 Select the partition number you wish to adjust ENTER Enter the new entry exit time in seconds 1 255 seconds MENU Moves back to step 4 partition selection MENU Moves back to basic system configuration menu selection step 2 MENU Exits back to main menu MENU Press menu to exit How to Adjust keypad LED intensity Step Example Set keypad led intensity 1 MENU 9 Selects main menu Option 9 Basic system configuration 2 4 Selects keypad LED intensity 3 Enter your Master user pin code 1 Display run mode led intensity 2 Display idle mode led intensity 4 3 Backlight run mode led intensity 4 Backlight idle mode led intensity 5 Logo On Off 5 Select LED intensity from 1 8 6 MENU Moves back to step 4 Run mode Idle mode selection 7 MENU Moves back to basic system configuration menu selection step 2 8 MENU Exits back to main menu 9 MENU Press menu to exit 22 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual Display run mode Controls the light intensity of the away stay status fire power icons and all zones numbers during the run mode Display idle mode Controls the light intensity of the away stay status fire power icons and all
6. MENU 8 Selects main menu Option 8 Voice message recording 2 Enter your master PIN code 4 Zone name 3 5 Partition name 6 Output name 4 ENTER Select which Zone Partition or Output number is tobe configured 5 ENTER Select library word 1 ENTER Select library word 2 ENTER Select library word 3 ENTER Select library word 4 ENTER Select library word 5 ENTER Select library word 6 ENTER Select library word 7 ENTER Select library word 8 Note Press away to reset names back to default 6 MENU Moves back to Zone Partition and Output number selection step 4 7 MENU Moves back to voice message recording menu step 3 8 MENU Moves back to main menu 9 MENU Exits main menu 20 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual Basic System Configuration Menu 9 Menu 9 Basic system configuration 1 Time and date Partition entry time Partition exit time Keypad light intensity Voice options Reserved Reset detector in alarm Call back Call answer O OoOo N OF a FB ODN Volume level Use this menu to e Adjust set the time and date to match your location e Change entry and exit times to suit your requirements e Adjust volume levels e Adjust backlight levels e Select different voice options e Reset detectors that have latched in alarm Note Some detection devices such as smoke de
7. on the NX 1815E whilst your security provider is on site Keep in mind the level of security you will obtain with this system relates specifically with two major factors e The quantity quality and placement of security devices attached to this security system e The knowledge you have of the security system and how that knowledge is utilized in a weekly test of the complete system This product is to be installed by qualified SERVICE PERSONNEL only The equipment should only be operated with an approved power adapter with insulated live pins Caution Risk of explosion if battery is replaced by an incorrect type Dispose of batteries according to the instructions Contact your service provider for replacement batteries NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual Glossary of terms Authority Level Arm Partition Away Mode Central Station Chime Mode Chime Group Communicator Duress Code Disarm Exit delay Entry delay Forced Arming The level of access assigned to a users pin code To turn your security system On A group of zones within the security system configured with individual control Users of the security system are assigned partitions that they are allowed to control To turn your security system on when you are leaving the premises Location where alarm signals are sent during an alarm report An operational mode that will emit a beep at the keypad when specific zones are ac
8. the keypad followed by the Enter ENTER i ENTER Press the corresponding number sequence on the keypad followed by the Enter key R Exit the premises or walk test the motion sensors NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 7 Indicators Icons and Lights Green System is ready STATUS Yellow System message present Red Flashing One or more zones are in alarm condition Red Steady System trouble message present To hear system messages press the status key Ns Green Partition is disarmed AWAY Off Partition is not ready to arm check zones Red Partition is armed in the AWAY mode AN Green Partition is disarmed and is ready to stay arm STAY off Partition is not ready to stay arm check zones Yellow Partition is armed in the STAY mode D Green OK FIRE Red Fire condition present 0 On Mains power is connected POWER Off Mains power is disconnected MENU Access main menu and when prompted allows users to exit sub menus ENTER Enters selected option use when prompted Partition Off Zone is OK LEDs f 1 16 Yellow flashing Zone is activated open Yellow steady Zone is bypassed isolated Away Arming Away arming is used when you are leaving and you want the premises protected in your absence If your service provider has enabled the forced arming feature you will be able to arm your security system with pre programmed zones not secure This featu
9. and are not cleared when the security system is armed and disarmed How to Control chime mode Step Example Turning On Off Chime Mode 1 MENU 2 Selects main menu Option 2 Chime Mode 2 0 Toggles chime mode On Off 3 MENU Exits back to main menu 4 MENU Press menu to exit How to Add a zone to the chime group Step Example Adding zone 4 chime group 1 MENU 2 Selects main menu Option 2 Chime Mode 2 4 ENTER Selects zone 4 3 0 Set Unset chime to this zone and adds it to the chime group 4 MENU Exits back to main menu 5 MENU Press menu to exit System Event History Menu 3 Menu 3 System Event History 1 Last alarm memory 2 Event history The Event History menu is used to listen to the last 185 events that occurred in your security system These events are held within your security systems memory and include events such as arming disarming system faults and alarmed zones All events are time date stamped so ensure your clock is set correctly in menu 9 Alarm memory is a quick recall of the last zone s that caused your security system to go into alarm condition 12 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual How to View alarm memory Step Example To review the zone zones that caused the last alarm condition 1 MENU 3 Selects main menu Option 3 Event History 2 Enter your Master pin code 3 1 To
10. ar 151 Yard 38 Bedroom 76 Guest 114 Reception 152 Zone 153 Gym NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 25 Programmed Phone Number Terier earan AENEA ATA E EAREN NTE T aAa Programmed Phone Number 2 assesrisesrsssrerrenraereineirarnennereerrisrarrereereensreeneenn E Stay Zone 24 Hour Zone Programmed Phone Number 3 cceeeeeee ee ee eens eee ee ee ee eens ease ease ee eeeeeeeaeaes Zone List 1 2 3 4 5 6 7 8 9 Dy wo gt on D A oo N N oO N NS N w 24 Service provide iaai aea i a a e eei Phonic iaeaea aE aaa EEY Monitoring station issiria inorri aeiaai PHONC 2 4 c2petinctidatrecededcottmatdeeadeeatan SYSISM iY PCa siestsincsy nlectacihen en actienbuechantenarhedawbuites wa stenavougs Date of installation 26 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual
11. atus Annunciation Turning this feature On will make your NX 181xx annunciate the partition condition when arming and disarming your system Turning this feature Off disables this feature Table 2 Voice Options 1 Full menu annunciation 3 Partition status annunciation 2 Time annunciation 4 Reserved NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 23 How to Reset latching detectors that are in alarm Step Example Reset smoke detectors shock sensors and latching glass break detectors 1 MENU 9 Selects main menu Option 9 Basic system configuration 2 7 Selects to reset detector in alarm and resets sensor 3 MENU Moves back to basic system configuration menu selection step 2 4 MENU Exits back to main menu 5 MENU Press menu to exit How to Adjust the volume level Step Example Adjust the volume level 1 MENU 9 Selects main menu Option 9 Basic system configuration 2 0 Selects volume level 3 Enter your master PIN code 4 Select required volume level from 1 8 5 MENU Moves back to basic system configuration menu step 2 6 MENU Exits back to main menu 7 MENU Press menu to exit 24 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual Word Library 1 One 39 Boat 77 Gun 115 Remote 2 Two 40 Cabinet 78 Hall 116 Roof 3 Th
12. commended that a communication test be carried out to verify connectivity Additional equipment is required for Divert and SMS messaging ask your service provider for further details Output Control Menu 7 Your security system can be configured to control up to 16 outputs These outputs can be used for a variety of applications such as external lighting control electric shutter control or even garage door control As additional equipment is required to enable these features please contact your service provider for further details How to Control outputs Step Example Control connected outputs 1 MENU 7 Selects main menu Option 7 Output Control 2 5 ENTER Select which output is to be controlled from 1 to 16 for example select output 5 3 Press 1 to turn output on touch 2 to turn output off 4 MENU Moves back to output selection NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 19 5 MENU Exits back to main menu 6 MENU Press menu to exit Voice Message Recording Menu 8 Menu 8 Voice message recording 4 Zone name configuration 5 Partition name configuration 6 Output name configuration Menu 8 allows you to build your own custom names for zones partitions and outputs using words from the word library table Up to eight words may be strung together to build a more detailed name Step Example Configure a zone name partition name or output name 1
13. ctivating As this test sounds all the audible devices connected to your security system it is advisable to notify neighbours and other persons within the premises prior to activating this test Communicator Test The Communicator is located within your security system The communicator if enabled is the device that communicates with a central station who analyse all the incoming alarm signals and engage the appropriate responses services dependant on the type of alarm signals received Alternatively the communicator can be enabled to call an alternate phone number like a mobile phone this is sometimes called self monitoring or domestic dialling When testing your communicator no sirens will sound and a test message will be sent to the central station for confirmation of the test If self monitored the person answering the number programmed in your security system will hear a siren sound when they answer the phone Contact the central station and any person whose phone numbers are programmed in the system prior to activating this the communicator test The communicator test is only available if your security system has been setup to dial a central station or enabled for domestic dialling Battery Test The backup battery is housed within your security systems main control box and provides power when mains power has been interrupted Prolonged operation using only the backup battery will result in total system failure so the condition of
14. d collection point For more information see www recyclethis info www utcfireandsecurity com or www interlogix com www interlogix com customer support or www utcfssecurityproducts eu Content Important information 4 Limitation of liability 4 Advisory messages 4 Warranty 4 Introduction 5 Glossary of terms 6 The NX 1815E 7 Legend 7 Indicators Icons and Lights 8 Away Arming 8 Stay Arming 9 Disarming 9 Emergency Activation Keys 10 Understanding the Main Menu 11 Controlling Zone Bypasses Menu 1 11 Control The Zone Chime Menu 2 12 System Event History Menu 3 12 System Test Menu 4 13 User Configuration Menu 5 16 Phone Number Configuration Menu 6 18 Output Control Menu 7 19 Voice Message Recording Menu 8 20 Basic System Configuration Menu 9 21 Word Library 25 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual Important information Limitation of liability To the maximum extent permitted by applicable law in no event will UTCFS be liable for any lost profits or business opportunities loss of use business interruption loss of data or any other indirect special incidental or consequential damages under any theory of liability whether based in contract tort negligence product liability or otherwise Because some jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damages the preceding limitation may not apply to y
15. dance with the instruction manual may cause harmful interference to radio communications You are cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Check local ordinances this device is not listed by an approved test lab to meet NFPA 72 and therefore may not be sold or installed for use with a fire system in some localities CE UTC Fire amp Security hereby declares that this device is in compliance with the applicable requirements and provisions of one or more of the Directives 1999 5 EC 2014 30 EU and 2014 35 EU For more information see www utcfireandsecurity com or www interlogix com 2002 96 EC WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designate
16. digits in length if this level of security is required User Partition Assigning different partitions to users s which sections partitions of the security system a user may access to User Authority Authorization levels determine the options available to user user authorization is where you would alter and increase a users authority to become a Master Code Users with Master PINs can create delete and modify other user codes with equal or less authority than themselves How to Configure set up a new pin code for a specific user Step Example Configure pin code 2580 for user 4 1 MENU 5 Selects main menu Option 5 User configuration 2 Enter your Master pin code 3 1 Selects to configure user pin 4 4 ENTER Selects user 4 5 aa Sets user 4 pin code as 2580 6 MENU Moves back to user configuration step 3 7 MENU Exits back to main menu 8 MENU Press menu to exit How to Delete a pin code from a specific user Step Example Delete the pin code that is configured for user 4 1 MENU 5 Selects main menu Option 5 User configuration 2 Enter your Master pin code 3 1 Selects to configure user pin 4 4 ENTER Selects user 4 5 0 ENTER To disable user 16 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 6 7 8 MENU MENU MENU Moves back to user configuration step 3 Exits back to main menu
17. fering security on the remaining zones bypassing zones lowers your level of security and caution should be exercised All bypassed zones are reset and cleared from memory when your security system is next armed disarmed Your security system must be disarmed turned off before being able to bypass zones After bypassing your selected zones your security system must be armed turned on in either the away or stay mode to secure the remaining zones Note Press status to check bypassed zones or simply arm your security system and all bypassed zones will be announced automatically How to Bypass a single zone Step Example How to bypass zone 5 1 MENU 1 Selects main menu Option 1 To control zone bypass 2 5 ENTER Selects zone 5 Toggles zone 5 from un bypassed to bypassed state or if already 3 0 bypassed from bypassed to un bypassed 4 MENU Exits back to main menu 5 MENU Press menu to exit NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 11 Control The Zone Chime Menu 2 You can setup your NX 1815E so that it will beep when selected zones are tripped or activated this is called chime Chime mode does not trigger any alarms and it is only used as a low level alert such as a customer entry door You can add and delete zones from the chime group offering a very flexible chime mode feature The zones you have selected to be in the chime group are stored in memory
18. level of protection provided by a professional monitoring station Divert phone numbers 1 2 and 3 will be called when an intercom call is initiated from an outdoor intercom entrance station How to Enter phone numbers Step Example Programming in alarm phone number 1 1 MENU 6 Selects main menu Option 6 Phone Number Configuration 2 Enter your Master pin code 3 1 Selects alarm phone number 1 4 Phong Enter the phone number that alarm phone number 1 will dial Number 18 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 5 ENTER Accepts the phone number entered 6 MENU Moves back to Phone number configuration 7 MENU Exits back to main menu 8 MENU Press menu to exit How to Delete phone numbers Step Example Delete alarm phone number 1 1 MENU 6 Selects main menu Option 6 Phone Number Configuration 2 Enter your Master pin code 3 1 Selects alarm phone number 1 4 0 Disables alarm phone number 1 5 ENTER Accepts deletion 6 MENU Moves back to Phone Number Configuration Te MENU Exits back to main menu 8 MENU Press menu to exit Note On the following pages you will find examples for entering and deleting alarm phone number one To enter or delete other phone numbers change only your phone number selection at step 3 Remember to seek permission from the owners of the phone numbers that you enter and it is re
19. ou In any event the total liability of UTCFS shall not exceed the purchase price of the product The foregoing limitation will apply to the maximum extent permitted by applicable law regardless of whether UTCFS has been advised of the possibility of such damages and regardless of whether any remedy fails of its essential purpose Installation in accordance with this manual applicable codes and the instructions of the authority having jurisdiction is mandatory While every precaution has been taken during the preparation of this manual to ensure the accuracy of its contents UTCFS assumes no responsibility for errors or omissions Advisory messages Advisory messages alert you to conditions or practices that can cause unwanted results The advisory messages used in this document are shown and described below WARNING Warning messages advise you of hazards that could result in injury or loss of life They tell you which actions to take or to avoid in order to prevent the injury or loss of life Caution Caution messages advise you of possible equipment damage They tell you which actions to take or to avoid in order to prevent the damage Note Note messages advise you of the possible loss of time or effort They describe how to avoid the loss Notes are also used to point out important information that you should read Warranty UTC Fire amp Security Americas Corporation Inc guarantees this product against defective parts and wo
20. ould only press these keys in an emergency situation that requires a response by a central station Check with your service provider to find out if your security system has these function keys enabled and clarify what responses if any will be provided upon activation Activating your personal emergency functions Fire 1 3 Press and hold for 2 seconds Medical 4 6 Press and hold for 2 seconds Panic 7 9 Press and hold for 2 seconds 10 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual Understanding the Main Menu Pressing the MENU key access the NX 1815E s main menu here you will find the 10 main features used for customisation and setup of your security system From the moment you press the menu key the NX 1815E s personal voice guide PVG will guide you through your chosen selection Menu 1 Zone bypass 2 Zone chime 3 Event history 4 System test 5 User configuration 6 Phone number configuration 7 Output control 8 Voice message recording 9 Basic system configuration 0 Advanced system configuration Controlling Zone Bypasses Menu 1 The zone bypass menu is used to bypass isolate selected zones in your security system A bypassed zone is not capable of activating an alarm as it is temporarily disabled from your system This option is commonly used to bypass zones that require service or zones that you wish to temporarily add to your stay mode Whilst still of
21. re is ideal for systems that have entry exit doors fitted with door contacts allowing you to arm your system with the door opened and protecting the door after its closed Your NX 1815E will announce all zones that are not secure when armed You may arm your system by entering your 4 or 6 digit user PIN code or if your service provider has enabled the quick arm feature you can simply press the Away key 8 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual Step Howto Arm your system in the Away Mode 1 Close all protected doors and windows ensure everyone has left the premises Ensure the status light is lit green 2 AWAY Press Away OR PH Enter your user pin code 3 A Vacate the premises immediately Stay Arming Stay arming is used when you are staying in the premises and wish to arm certain zones and bypass others IE Arming the perimeter of the premises whilst automatically bypassing all the internal movement sensors If an armed zone is alarmed whilst your security system is in the stay mode it will initiate a warning tone at your NX 1815E and your sirens will sound at the end of this warning Your service provider predetermines this warning time at the time of installation Step Howto Arm your system in the Stay Mode Close all protected doors and windows If motion sensors are included in your Stay mode 1 have everyone move out of those partitions Ensure
22. ree 41 Car park 79 Hallway 117 Room 4 Four 42 Ceiling 80 Heat 118 Rumpus 5 Five 43 Cellar 81 Heating 119 Safe 6 Six 44 Chil s 82 Hold up 120 Security 7 Seven 45 Alert 83 Home 121 Sensor 8 Eight 46 Closet 84 Home theatre 122 Shed 9 Nine 47 Computer 85 Infrared 123 Shock 10 Ten 48 Cool 86 Inside 124 Shop 11 Eleven 49 Curtain 87 Instant 125 Side 12 Twelve 50 Data 88 Interior 126 Skylight 13 Thirteen 51 Den 89 Key switch 127 Sliding 14 Fourteen 52 Detector 90 Keychain 128 Small 15 Fifteen 53 Dining 91 Kitchen 129 Smoke 16 Sixteen 54 Door 92 Large 130 South 17 Seventeen 55 Downstairs 93 Laundry 131 Stairs 18 Eighteen 56 Driveway 94 Lift 132 Storage 19 Nineteen 57 Duress 95 Light 133 Study 20 Twenty 58 East 96 Living 134 Temperature 21 Thirty 59 emergency 97 location 135 tennis 22 Forty 60 Exterior 98 Master 136 Toilet 23 Fifty 61 Family 99 Medicine 137 Training 24 Sixty 62 Fan 100 Meeting 138 TV 25 Seventy 63 Fence 101 Motion 139 Upstairs 26 Eighty 64 Fire 102 Night 140 User 27 Ninety 65 Forced arm 103 North 141 Utility 28 Hundred 66 Foyer 104 Nursery 142 Volt 29 Thousand 67 Freezer 105 Office 143 Veranda 30 Air conditioner 68 Front 106 Output 144 Wall 31 Area 69 Games 107 Outside 145 Warehouse 32 Attic 70 Garage 108 Panic 146 Water 33 Automatic 71 Gas 109 Pantry 147 West 34 Auxiliary 72 Gate 110 Partial 148 Window 35 Back 73 Glass 111 Perimeter 149 Windows 36 Basement 74 Glass break 112 Pool 150 Wireless 37 Bathroom 75 Ground 113 Re
23. reviews last alarm memory 4 MENU Moves back to alarm memory event history selection step 3 5 MENU Exits back to main menu 6 MENU Press menu to exit How to Review event history To review events held within your security system up to 185 events Step Example are stored 1 MENU 3 Selects main menu Option 3 Event History 2 Enter your Master pin code 3 2 To reviews last alarm memory 4 MENU Moves back to alarm memory event history selection step 3 5 MENU Exits back to main menu 6 MENU Press menu to exit System Test Menu 4 Menu 4 System Test 1 Siren Test Communicator Test 2 3 Battery Test 4 Zone Walk Test 0 System Version number Your security system is made up of different components brought together to produce a very powerful yet easy to use security system These components are your sirens communicator back up battery and detection devices All these different components require regular testing and maintenance in order for them to remain in peak operational performance These components can be tested from this menu and should be scheduled for a weekly test Failure to conduct regular testing can result in system failure when most required The four available system tests are NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 13 Siren Test The Sirens are used as audible deterrents in the event of your security system a
24. rkmanship for twenty four 24 months from the date of purchase If any defect appears during the warranty period contact your service provider UTC Fire amp Security Americas Corporation Inc assumes no liability for consequential or indirect damage and accepts no responsibility for repairing 4 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual damage to the product caused by misuse careless handling or where repairs have been made by others No other guarantee written or verbal is authorized by UTC Fire amp Security Americas Corporation Inc Introduction Your NX 1815E is an intuitive interface for users of your security system It delivers one of the most user friendly experiences for controlling a security system available today Its voice prompts enable even the newest users to immediately utilize the full power of your security system We trust that you will enjoy your NX 1815E and we would like to thank you for choosing a NetworX Security System All users of your security system should read and follow the instructions and precautions in this manual before operating your security system Failure to do so could result in the security system not working as intended This manual should be kept in an accessible location for the life of the security system If you do not understand any part of this manual you should ask your service provider for further clarification Read the entire manual and if possible practice
25. tectors shock sensors and some glass break detectors latch their alarm lights to indicate an alarm condition These types of detectors require resetting use the Reset Detector in Alarm menu to acknowledge and clear these lights Note The Call back and call answer options are service tools for your service provider and are not listed in these instructions but will be announced when you enter this menu option How to Setting the time and date Step Example Seiting the time as 9 30AM and the date as 19 6 2009 1 MENU 9 Selects main menu Option 9 Basic system configuration 2 1 Selects time and date configuration 3 Enter your Master user pin code 4 1 To configure the time 5 9 ENTER Enter the current hours value i e 9 o clock 6 30 ENTER Enter the current minutes value i e 30 minutes NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 21 10 11 12 13 14 1 Selects AM time 2 To configure the date 19 ENTER Enter the current day i e 19th 6 ENTER Enter the current month i e June sixth month 2009 ENTER Enter the current year must be 4 digits i e year 2009 MENU Moves back to basic system configuration menu selection step 2 MENU Exits back to main menu MENU Press menu to exit How to Adjust partition entry or exit times Step Example Adjust entry or exit times 1 OS IN SO a P e DN MENU
26. th 16 zone LEDs User Manual 17 Notes The system must be disarmed before accessing user configuration Do not remove all partitions from a users partition control Use extreme caution when modifying a user with master code authority If you attempt to enter a PIN code that is already being used by another user the following announcement will be heard PIN code has failed followed by three fast beeps simply select another PIN code Keep user PIN information in a safe place do not disclose your PIN to others Contact your service provider to confirm available PIN codes and partitions on your system Phone Number Configuration Menu 6 Menu 6 Phone number configuration 1 Alarm phone number 1 Alarm phone number 2 Alarm phone number 3 Divert phone number 1 Divert phone number 2 oO Oo N OO N Divert phone number 3 Menu 6 Alarm phone numbers will only be available if your system is configured for self monitoring also known as domestic dialling If self monitoring is enabled and a suitable connection to the telephone network is available your security system has the ability to call three different numbers in the event of an alarm condition these are alarm phone numbers 1 2 and 3 A siren tone will be heard by the receiving party and the call can be terminated ended by pressing and holding the star key on the receiving phone Caution should be used when selecting self monitoring as it does not offer the same
27. the battery is critical to sustain the power required for the longest period of time It is recommended to change your battery at periodical intervals please refer to your service provider for further information This feature is used to test the condition of your back up battery Zone Walk Test Zone Walk test is used to test the connectivity between your alarm devices IE motion sensors door contacts etc and your security system When in walk test mode your NX 181xx will emit the chime beep each time a zone is activated and chirp the outside siren Partition Lights will also blink red after a detection device in that partition has been activated You must exit Walk Test mode when you are satisfied all the zones function correctly Your communicator will not function during this test System Version number This menu is a service tool for your system provider Step How to Perform a siren test 1 MENU 4 Selects main menu Option 4 System Test 2 Enter your Master pin code 3 1 Selects the siren testing External and internal sirens will sound 14 NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 4 AWAY To stop sirens within 30 seconds 5 MENU Moves back to system test menu step 3 6 MENU Exits back to main menu 7 MENU Press menu to exit Step How to Perform a communicator test 1 MENU 4 Selects main menu Option 4 System Test 2
28. the status light is lit green 2 STAY Press Stay 3 Your security system is now armed in the stay mode Disarming Make your way to the NX 1815E through one of the designated entry exit doors When you are detected entering your NX 1815E will repeat a warning message for the duration of the entry delay until a valid PIN code is entered Your sirens and communicator will activate at the end of the entry delay time if a valid PIN code is not entered Away and Stay modes can be configured with different entry delay times ask your service provider for further details Step Howto Disarm your system from either the Away or Stay Modes Enter the premises through your designated entry door s If your security system has been designed to detect your presence when making your way to the NX 1815E a warning message reminding you to turn off your security system will be announced If your presence is not detected no warning message is announced 2 Enter your user PIN code to disarm from either the away or stay arming modes Your system is now disarmed from either the Away or Stay modes NX 1815E NetworX Voice Keypad with 16 zone LEDs User Manual 9 Emergency Activation Keys Three 3 emergency functions are available via your NX 1815E to provide personal support in areas of Fire Medical and Police duress alarm To activate these functions press and hold the required keys for two seconds You sh
29. tivated All the zones that will activate chime when in chime mode The device that communicates alarm signals generated from your security system to your central station A predetermined user pin code that will arm disarm the security system whilst sending a special code to the central station indicating the user is entering leaving the premises under duress Only applicable on monitored systems To turn your security system Off The time allowed to exit the premises after the security system is armed The time allowed to disarm your security system after the first detection device has been activated An option that allows certain zones not to be secure when arming A security system that is ready to be force armed will flash the corresponding partition light green Generally assigned to detection devices that cover the NX 181xx e g motion sensors front door reed switches allowing the user to arm the security system without the need to wait for those zones to be secure Master Code A four 4 or six 6 digit pin code that is used by a user to arm or disarm the security system Its main feature is the ability to create alter and delete user pin codes Can also be used as a function code for all features NOTE Your security system may have either four 4 digit pin codes or six 6 digit pin codes but not a mixture of both Monitored A security system that is configured to send all alarm signals to a central station
30. zones numbers during the idle mode Backlight run mode Controls the light intensity of the lights located behind the rubber keys during run mode Display idle mode Controls the light intensity of the lights located behind the rubber keys during idle mode Logo Switches On Off the logo located at the top of the keypad Note The keypad lights will switch from run mode to idle mode 60 seconds after the last key press Pressing any key will wake the keypad from idle mode and switch it to run mode How to Activate Deactivate different voice options Step Example How to activate or deactivate individual voice options 1 MENU 9 Selects main menu Option 9 Basic system configuration 2 5 Selects voice options 3 Enter your Master user pin code 4 Select required feature to activate deactivate Refer to Table 2 below 5 MENU Moves back to basic system configuration menu selection step 2 6 MENU Exits back to main menu 7 MENU Press menu to exit Full Menu Annunciation Turning this feature On gives full descriptions to all the options within the main menu Turning this feature Off shortens the descriptions to all options within the main menu This is a feature for experienced users Time Annunciation Turning this feature On will make your NX 181xx annunciate the time and date during exit and entry delays Turning this feature Off disables this feature Partition St
Download Pdf Manuals
Related Search