Home

MINI-PTZ-12X Manual

1. Space MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETTING CLOCK SETTING COMM SETTING BACK EXIT INITIAL INFO S N 4JKAA7824000058 FIRMWARE V2 50 PROTOCOL ACTORY DOME ADDRESS 001 COMM 2800 N 8 1 BACK EXIT 4 SYSTEM SETTINGS INITIAL DISPLAY INFORMATION 1 The system enters into the main menu by calling 95 presets or by calling 9 preset twice within 3 seconds 2 Tilt up down joystick to select SYSTEM SETTING and then select OPEN to enter submenu 3 Tilt joystick up down to the INITIAL INFO menu option press OPEN to display initial information shown in the picture to the left Initial information includes S N serial number of the dome the name of manufacturer soft edition camera address and communication parameter System settings may change the numerical value of initial information 11 4 SYSTEM SETTINGS DISPLAY SETUP 1 The system enters into the main menu by calling 95 preset or by calling SYSTEM SETTING 9 preset twice within 3 seconds CAMERA SETTING FUNCTION SETTING 2 lilt joystick up down to select SYSTEM SETTING then press OPEN to enter WINDOW BLANKING submenu EXIT 3 Tilt joystick up down to select DISPLAY SETUP then press OPEN to enter Display Setup menu To set display setup content please see below e DOME LABEL
2. dome label display setting e PRESET LABEL preset label or scan label display setting ZOOM LABEL magnification display setting ZONE LABEL zone label display setting SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DIRECTION LABEL direction label display setting DISPLAY SETUP e TEMPERATURE LABEL temperature label display setting C ENT TIME LABEL time label display setting PASSWORD SETTING DATE LABEL date label display setting CLOCK SETTING COMM SETTING NE BACK 4 Taking Display dome label as an example to explain the operation process tilt BX joystick up down to move cursor to the DOME LABEL OFF option then select OPEN there is a sign 1 besides the DOME LABEL option the cursor will be flashing on and off beside OFF as the picture on the left shows 5 By tilting the joystick up down set the switch to either ON OFF When it is set to ON it displays dome label then press OPEN and the cursor will jump DOME LABEL OFF back to the DOME LABEL option When label setup is finished move the PRESET LABEL OFF ZOOM LABEL OFF ZONE LABEL OFF DIRECTION LABEL OFF TEMPERATURE LABEL OFF TIME LABEL OFF Through the information on the screen the user can see current dome s inside ET LABEL OFF temperature magnification display zone etc When all the labels are displayed EXIT the dome displays the following image below in the image 305 is the pan angel 45 is the tilt angle DI
3. PRESETS PRESET NUMBER 05 SEI PRESET SHOW PRESET CLEAR PRESET EDIT PRESET LABEL BACK EXIT EDIT PRESET LABEL LABEL PRESET 05 BACK EXIT 26 PRESET SETTING 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds Click each command to enter preset menu ACC OPRELENOABERP sel Boe Mieke cvs al preset SET PRESET SHOW PRESET CLEAR PRESET EDIT PRESET LABEL Define and call preset function which can be set via the keyboard operation Input preset number at first then click the Save reset call preset key 2 Define the current preset number move the cursor to PRESET NUMBER press OPEN to choose the preset number the range is 01 128 as the left picture shows Choose number 5 as the current preset the following operations aim at the current preset Define current preset move the cursor to SET PRESET then press OPEN by operating joystick to adjust magnification you can choose a good objective image Press OPEN to save If the image is close up use the digital zoom to adjust image When setting the preset the image will jump to maximum optical zoom amount OPERATION KNACKS The preset function of the dome stores current pan tilt angle zoom and other position parameters into the memory When necessary the dome recalls these parameters and adjusts camera to that position Display current preset move th
4. Replace power supply No action no power up The dome DIP switch setting is incorrect Refer to original switch setting reset the switch Self testing and video image are Check Rs485 connection confirm normal but the 5430 that the cable is connected securely dome is Please consult appendix Rs485 Bus acknowledge Video line has a faulty connection Test and correct faulty connection Video image is not steady ae Replace the power adapter It is better to ONION ES locate the switch and power adapter near the dome Video image is not steady and the Power consumption is not enough Replace the power uncontrollable Rs485 connection is malfunctioning motor is malfunction The Control line has a bad connection Power running off the E line is either too high or too 2 Increase Distributor power output OW The movement of 1 Install a 1200 resistance to the dome the dome is not smooth enough CLEANING THE CLEAR DOWN COVER To obtain consistently clear video footage user should clean the down cover periodically 1 Please use caution when cleaning Hold the down cover ring to avoid directly touching the acrylic down cover Direct contact with down cover will leave sweat residue that can corrode the outer coating and could also leave scratch marks 2 Use a soft dry cloth or a substitute to clean the inner and outer surfaces 3 For hand contamination of the acrylic cover plea
5. complete the fifth step again valid if itis set to OFF that means the setting password is invalid If the user has forgotten their password and cannot enter into the main menu the user can use the super password The PTZ s password will be changed to the initial one atthis point the User needs to reset the password The PTZ s initial password is 000000 Super password is 892226 16 MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETTING CLOCK SETTING COMM SETTING BACK EXIT CLOCK SETTING 15 11 41 07 08 27 4 SYSTEM SETTINGS DATE AND CLOCK SETTING The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 second Move the cursor to SYSTEM SETTING by moving the joystick up and down Press OPEN to enter into the next menu Move the cursor to CLOCK SETTING by moving the joystick up and down Press OPEN to bring up the clock settings you could set the following TIME e DATE As an example Move the cursor to TIME then press OPEN Please move the cursor to the first number the three numbers are hour minute and second It also means year month an the date under the DATE Set the Hour by tilting the joystick up down Set the MINUTE and SECOND by turning the joystick right and left Press OPEN to sav
6. operation LE Built in digital camera High sensitivity high resolution and integrated digital processing Auto focus Auto lris Auto brightness control Auto white balance IR cut filter Auto back light compensation Auto slow shutter Built in high resolution colour camera with pre focus lens Pre focus lens 6mm 8mm 12mm Optional Auto brightness controlling Auto white balance Auto back light compensation Auto iris Auto focus Integrated multi protocol decoder Figure design all the data is stored in the inside of camera pan tilt When the power is turned off the storage data cannot be lost Built in decoder and multi protocol includes PELCO D PELCO P SAMSUNG PANASONIC and other mainstream protocols The protocols can be automatically recognised by the dome and it can choose corresponding protocol to communicate with host Manual setup not needed 128 presets can be stored Supports auto tour but only can only transfer 1 80 presets and 1 tour can store up to 32 presets 4 pattern tour 4 scan Built in direction indicator Built in temperature indicator Built in clock setting e RS485 bus controlling in series and dome ID 1 255 optional Built in Pan Tilt 6 e and carbon alloy structure high intensity good heat dissipation Precise stepping motor rotates smoothly reacts sensitivity and orientates accurately Exquisite mechanical drive
7. reduce the heat This is to prolong the life time of the dome by insuring that it continues to work within a reliable temperature environment range 4 SYSTEM SETTINGS BASIC OPERATION Current carrying to dome and self testing The dome conducts a self testing routine in which it firstly rotates slowly until it meets the pan origin default setting then it will start moving to the tilt origin setting and then the lens will be pulled from far to near and near to far When self testing is finished the relevant system information is displayed onto the screen as shown below S N of the dome 2 24 Soft edition vier AU Protocol i JB The information will not disappear until you stop to operate the system If you set power up action the dome will automatically activate pan and tilt motions after self testing How do use this function We will explain in provide a detailed introduction in the following passages Calling up the main menu The system enters into the main menu by 95 presets or twice the transfer 9 presets within 3 seconds All new menu settings must enter into the main menu first To enter the main menu you must enter the password When trying to enter the main menu for the first time you will need to enter the main super password 892226 This will allow you to create and set your own custom password The factory setting password is 000000 Menu and keyboard opera
8. support pan 360 continuously and tilts 0 90 and may rotate180 with auto flip Rotates slowly as 1 s pan speed meaning image doesn t jitter OSD menu Al the menu option are displayed in English Video OSD menu It is direct and simple to revise the dome information and parameters via the keyboard and menu display You can set park action power up action or arrive an appointed action Internal temperature test e When the temperature exceeds the upper limit the screen will display alarm information According to the real time temperature an inbuilt fan will keep the temperature stable 3 FEATURE INFORMATION This section predominantly describes the main functions and general principles of the integrated speed dome and does not refer to the integral operation methods AUTO RUN MOTION Focus speed proportion pan When adjusting manually for focussing on far distances the dome responds at a high speed so that touching rocker slightly may make picture move rapidly thus causing the picture to become blurred The dome automatically adjusts the pan and tilt rotation according to when you are zooming in or out which makes it convenient to operate manually and to track an object in the field of view In the menu you may change system parameter setting for proportion pan to ON so you can may run this function Auto flip If user holds the joystick in the down position the camera pans 180 degrees then the camera t
9. when AE mode is brightness SHUTTER N A priority this function can be set IRIS N A BRIGHT N A WB MODE AUTO OPERATION KNACKS R GAIN N A Quality of the Image relates to the exposure amount i e how B GAIN N A much light the CCD receives to produce a legible image Exposure ENTER CAMERA MENU amount is relative to the length of light let in to the camera BACK depending on shutter speed and the strength area of light up EXIT to the size of iris ADVANCE SETTING The camera can automatically calculate a suitable exposure amount according to brightness of scenery and CCD sensitivity In the situation that the exposure amount is certain SHUTTER shutter priority fixes the shutter speed and the camera will auto decide how much iris to use IRIS iris priority adjusts the size of the iris and automatically adjusts the shutter speed BRIGHT brightness priority is the point that the camera TTL checks 24 the light directly and controls the brightness of image MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT CAMERA SETTING ZOOM SPEED HIGH DIGITAL ZOOM ON BLC MODE OFF SLOW SHUTTER X2 IR CUT FILTER ADVANCE SETTING BACK EXIT ADVANCE SETTING AE MODE AUTO SHUTTER N A IRIS N A BRIGHT N A WB MODE AUTO R GAIN N A B GAIN N A ENTER CAMERA MENU BACK EXIT ADVANCE SETTING AE MODE AUTO SHUTTER N A IRIS N A BRIGHT N A WB MODE AUTO R GAIN N A B GAIN N A E
10. 1 ADVANCE SETTING CLEAR SCAN COMM 4800 N 8 1 RUN SCAN BACK AE MODE AUTO EDIT SCAN LABEL SHUTTER N A EXIT BACK IRIS N A EXIT BRIG N A DISPLAY SETUP PATTERNS a WB MODE AUTO IUE DOME LABEL R GAIN N A PATTERN NUMBER 1 PRESET LABEL B GAIN N A PROGRAM PATTERN ZONE LABEL ENTER CAMERA MENU RUN PATTERN ZOOM LABEL BACK CLEAR PATTERN DIRECTION LABEL TEMPERATURE LABEL Back n c TIME LABEL EXIT DATE LABEL BACK EXIT TOUR PO S TM 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 LABEL AUTO SCAN BACK EXIT LABEL PATTERN 1 BACK EXIT AUTO FLIP PROPORTION PAN PARK TIME PARK ACTION POWER UP ACTION FAN ENABLED TEMP C F HEAD UP BACK EXIT ZONES EDIT ZONE LABEL ZONES NUMBER CLEAR PASSWORD SETTING SET LEFT LIMIT CLEAR ALL ZONES OLD PASSWORD t ttt PLI ane CLEAR ALL PRESETS NEW PASSWORD EDIT ZONE LABEL CLEAR ALL PATTERNS CONF PASSWORD BACK CLEARGBER TOUT ENABLE PASSWORD OFF Su EXIT EXIT TIME RUNNING TIME CHANNEL CLOCK SETTING START TIME END TIME Ted I 201 07 08 27 LABEL ZONE 1 BACK EXIT CLEAR ALL WINDOWS FACTORY DEFAULTS RESTART BACK EXIT RUNNING COMM SETTING S N 4JKAA7824000058 CONF 4JKAA7824000058 SITE ID 001 33 COMM SPEED 4800BPS BACK EXIT 8 APPENDIX TROUBLE SHOOTING Trouble Possible causes Solution Power supply is damaged or there is not enough power being supplied
11. AL ZOOM If you do not want to activate this setting tilt the joystick so that it is set to OFF BLC MODE OFF SLOW SHUTTER X2 4 Press OPEN to save CUT FILTER ADVANCE SETTING BACK OPERATION KNACKS EXIT When digital zoom be set as ON the maximum zoom magnification of the dome is digital zoom magnification x optical zoom magnification When the digital zoom is set as OFF the maximum zoom magnification of the dome is only optical zoom magnification 20 5 CAMERA SETTINGS MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT CAMERA SETTING ZOOM SPEED HIGH DIGITAL ZOOM ON BLC MODE OFF SLOW SHUTTER X2 IR CUT FILTER ADVANCE SETTING BACK EXIT BACK LIGHT COMPENSATION 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick move the cursor to CAMERA SETTING to enter submenu 3 Operate joystick move the cursor to BLC MODE and press OPEN There will be a sign 1t in the front of BLC MODE the cursor will jump to the right tilt joystick to open or close back light compensation function Choosing ON activates back light compensation mode choosing OFF deactivates back light compensation mode 4 Press OPEN to save OPERATION KNACKS Strong background rays can cause the back lighted objects to generate shadows The speed dome can auto adjust the iris to match with the changes o
12. G BACK EXIT EDIT DOME LABEL LABEL SPEED DOME BACK EXIT EDIT DOME LABEL When you are using more than one PTZ dome on your CCTV system in order to identify each dome from one another this camera supports title setting You can set the title following these steps 1 The system enters into the main menu by calling 95 presets or by calling 9 preset twice within 3 seconds 2 Moving the joystick up and down move the cursor to SYSTEM SETTING and pressing OPEN to enter the next menu 3 Moving the joystick up and down move the cursor to EDIT DOME LABEL and select OPEN to enter the label setting menu 4 Moving the joystick up and down move the cursor to LABEL SPEED DOME and select OPEN to edit current label 5 Enter camera label name where the cursor is flashing on and off Move the joystick to select each character After editing select OPEN to save 6 Move the joystick to highlight and select BACK press OPEN to back to the previous menu NOTICE The label can set up to 16 characters for a label name By selecting OPEN continuously to jump each character and use the spacebar to replace the deleted characters When you finish editing one character select OPEN to move on to the next editing character when you have completed editing all of the characters select OPEN ito save Select CLOSE to exit Here are the range of characters you are able to use to create PTZ dome 0 9 A Z lt gt
13. IMIT SET RIGHT LIMIT FUNCTION SETTING RUN SCAN PRESETS e CLEAR SCAN SCAN e EDIT SCAN LABEL PATTERNS TOUR 2 Scan speed setting operate joystick to SCAN SPEED press ZONES OPEN tilt the joystick up down to adjust scan speed then press OPEN TIME RUNNING E ae BACK EXIT 3 Left limit setting operate joystick to SET LEFT LIMIT press OPEN operate joystick to choose objective image press OPEN to save 4 Edit scan label operate joystick move the cursor to EDIT SCAN LABEL press OPEN to enter submenu Edit label move the SCAN NUMBER 01 cursor to LABEL the system will auto set the label as AUTO SCAN SCAN SPEED 50 press OPEN to revise SET LEFT LIMIT SET RIGHT LIMIT NOTICE The label can set up to 16 characters characters and doesn t RUN SCAN need editing Pressing Open continuously to jump over and use the CLEAR SCAN spacebar to replace the deleted characters When you finish editing a character press Open to goto the next character to edit when you have EDIT SCAN LABEL finished editng press Open to save BACK EXIT Press Close to exit Character of label is suitable for choosing as follow 0 9 A Z lt gt and Space 5 Run scan operate joystick to RUN SCAN press OPEN to exit EDIT SCAN LABEL the menu and it will start to run the scan BACK 1 left limit and right limit of scan can t be set the same point EXIT 2 Under scan process speed ma
14. IN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING display zone label as it runs some zone It is a good idea to set a zone label so WINDOW BLANKING EXIT will set label for each zone When setting ZONE LABEL as ON the dome will you know which setting is which 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds FUNCTION SETTING 2 Operate joystick move the cursor to FUNCTION SETTING press OPEN PRESETS to enter submenu SCAN PATTERNS TOUR 3 Operate joystick move the cursor to ZONES press OPEN to ZONES TIME RUNNING enter submenu as the left picture shows BACK EXIT e ZONES NUMBER choose a zone number as current zone there are different choices in the menu e SET LEFT LIMIT set current zone s left limit SET RIGHT LIMIT set current zone s right limit e CLEAR ZONE clear current zone setting ZONES NUMBER SET LEFTEMNIT e EDIT ZONE LABEL edit current zone label as zone number is 1 Zone SET RIGHT LIMIT CLEAR ZONE EDIT ZONE LABEL BACK EXIT Regard the left right limit as the demarcation line and set the middle part as a label will auto change to ZONE 1 zone Various operational ways are the same as other settings in the menu EDIT ZONE LABEL LABELZONE 1 BACK EXIT 30 6 FUNCTION SETTING MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT FUNCTION SETTING PRESETS SCAN
15. ION PAN ON PARK TIME 005 PARK ACTION SCAN POWER UP ACTION AUTO FAN ENABLED 040 TEMP C F CENT HEAD UP OFF BACK EXIT PARK ACTION This setting allows the dome to run an appointed action after it has entered vacancy for a short time 1 240 minutes If default is set as 0 it will not run this action 1 Operate joystick move the cursor to select PARK TIME press OPEN and tilt the joystick up down to set park time the range is 0 240 minute press OPEN to save PARK ACTION runs an action when camera is parked when PARK TIME sets as 0 you cannot set this option 2 Operate joystick move the cursor to PARK ACTION then press OPEN there will be a sign 13 in the front of PARK ACTION move the cursor to right to choose Park Action Shown below are the list of options when you selected the desired option press OPEN to save NONE default no action e PRESET use preset 1 SCAN run scan PAT1 run pattern X e TOUR run tour POWER UP ACTION When the dome startups it will run preset actions once it has completed a self test if nobody intervenes with it the dome will repeatedly run this action continuously if default sets as NONE 1 Operate joystick move the cursor to POWER UP ACTION then press OPEN to jump to the following choice tilt up down joystick to choose Power Up Action then press OPEN to save e NONE none action e AUTO the dome resumes the primary ac
16. N ee a 2 CORRESPONDING ITEM SHEE 2 DETAILS OPRELEVUANTPAETS ae 2 SOE VII TINT 2 WAIL 3 STING TLS 3 2 DOME PERFORMANCE 5 reece 5 SOE CIP ICA 5 PERFORMANCE amp FEATURES 6 3 1 44 7 AUTORUN ene 7 SS ANE CON TRO ee 7 MONITOR NVC cc eee 8 4 SYSTEM SETTINGS 9 OPERATI ON see 9 EDIT DOME 10 ZINITIAEDISPEAS INFORMATION 11 SEN ET 0 ee ere E eee ee ee 12 SXSTEMATIOMOTIONOONTBOD diede 13 AUTO FI 13 SSPEEDPBOBORTIONBAN ee 13 NM ege 14 UP AC TION 14 eFANSTABPUPTENMPERATUPRE ee 14 SHEADUPMODNTING eee 14 BiG A 15 PASSWORD SETTINGS EE eE 16 DAE 17 Ge MUP DOME eRe ers 18 S CAMERA SETTING S E 19 ZOON PE ED eee r
17. NTER CAMERA MENU BACK EXIT 5 CAMERA SETTINGS WHITE BALANCE MODE System supports AUTO indoor mode INDOOR outdoor mode OUTDOOR auto track mode ATW single mode OPW OP mode manual mode MANUAL and different kinds of white balance modes Detail setup is as follows 1 The system enters into the main menu by calling 95 presets or by calling 9 presets twice within 3 seconds click each command enter into advanced setting menu according to the order in left picture 2 Operate joystick move the cursor to WB MODE to choose white balance mode then press OPEN to save Auto mode AUTO is the default mode of speed dome which auto reverts to real colour after the white balance sensor checks the environment for the camera When choosing manual mode MANUAL adjust the numerical value of R GAIN and B GAIN e R_GAIN the range is 1 225 the higher the numerical value the more warm red tone is added e B GAIN the range is 1 225 the higher the numerical value the more cold green tone is added CAMERA MENU SETTING 1 Operate joystick move the cursor to ENTER CAMERA MENU press OPEN to enter into camera menu setting When the camera displays N A it means that there is no such fuction 25 6 FUNCTION SETTING MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT FUNCTION SETTING PRESETS SCAN PATTERNS TOUR ZONES TIME RUNNING BACK EXIT
18. PATTERNS TOUR ZONES TIME RUNNING BACK EXIT TIME RUNNING TIME CHANNEL START TIME 00 00 END TIME 00 00 RUNNING NONE TIME RUNNING SETTING 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick move the cursor to FUNCTION SETTING press OPEN to call the submenu 3 Operate joystick move the cursor to TIME RUNNING Tilt the joystick up and down to set the time channel This system can set up to 4 time channels Press OPEN then choose is the current time channel the following operations is only for current time channel 4 Set the start and end time move the cursor to START TIME by tilting the joystick up and down to set the start time Press OPEN to save Move the cursor to END TIME by tilting the joystick up and down to set the end time press OPEN to save 5 Motion setting operate joystick move the cursor to RUNNING press OPEN there will be a sign a to displaying in front of RUNNING move the cursor to the right tilt the joystick up and down to choose the motion in the corresponding time channel then press OPEN to save The following items can now be selected 31 7 PRIVACY ZONE MASKING MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT The Privacy masking function can place pieces of regional shielding over areas on the video image that you do not want to b
19. QUIS 12X OPTICAL ZOOM PTZ DOME CAMERA USER S MANUAL ENHANCE YOUR DVR WITH OUR WIDE RANGE OF QVIS CAMERAS OUR PRODUCTS ARE FULLY TESTED TO WORK TOGETHER DONT SETTLE FOR LESS ALL OUR PRODUCTS CARRY QUIS Welcome Thank you for purchasing the Mini 12X PTZ dome This user s manual is designed to be a reference tool for the installation and operation of your system Here you can find information about the corresponding camera s features and functions as well as a detailed installation method Before installation and operation please read the following safeguards and warnings carefully QVIS IMPORTANT SAFEGUARDS AND WARNINGS 1 ELECTRICAL SAFETY All installation and operations here should conform to your local electrical safety codes We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modification or attempted repair 2 TRANSPORTATION SECURITY 41 heavy stress violent vibration or contact with water is allowed during transportation storage and installation Please use the original packing material or the material of the same quality when you ship it back to the manufacturer INSTALLATION Do not apply power to the product before completing installation Do not put object s on the product ENVIRONMENT This product should be installed in a cool dry
20. SPLAY SETUP cursor to the EXIT option exit to the previous menu The display information on the screen will change with the dome rotation Preset labe Zone label 4 Direction label 15 11 41 Time label 01x 07 08 27 lt Date label 12 Zoom magnification label MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETTING CLOCK SETTING COMM SETTING BACK EXIT MOTION AUTO FLIP ON PROPORTION PAN ON PARK TIME 005 PARK ACTION SCAN POWER UP ACTION AUTO FAN ENABLED 040 TEMP C F CENT HEAD UP OFF BACK EXIT 4 SYSTEM SETTINGS SYSTEMATIC MOTION CONTROL Systematic motion controlling can allow you to control a series of movement of the dome and plays an important role in controlling the image of the dome 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Tilt the joystick up down to select SYSTEM SETTING option then press OPEN to enter submenu 3 Tilt the joystick up down to select MOTION press OPEN to enter systematic motion controlling menu as shown on the picture to the left AUTO FLIP Operate joystick move the cursor to AUTO FLIP then press OPEN to enter Auto Flip setting tilt up down joystick to select option Choose ON to open Auto Flip or choose OFF t
21. URS DISPLAY SETUP e CLEAR ALL WINDOWS MOTION e FACTORY DEFAULTS restores the Factory default Please CLEAR be cautious to use this function as it will clear all modified PASSWORD SETTING setup parameters CLOCK SETTING COMM SETTING e RESTART Restarts dome BACK EXIT 4 Using Set Clear Zone as an example to explain the process Tilt up down joystick to select CLEAR ALL ZONES then press OPEN to clear all zones Once you selected the Clear All commands in the controlling menu modified setup parameters cannot be restored so please be careful and make sure it is ok to select one of these options CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEAR ALL TOURS CLEAR ALL WINDOWS FACTORY DEFAULTS RESTART BACK EXIT Lo 4 SYSTEM SETTINGS PASSWORD SETTING MAIN MENU Password setting option is a built in function of the high speed dome By setting SYSTEM SETTING CAMERA SETTING a password 6 character long it is useful to protect the dome settings from unauthorised access If you do know the password you can t enter the setting FUNCTION SETTING menu The initial password of the dome is 000000 WINDOW BLANKING EXIT 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Tilt the joystick up and down to move the cursor to the SYSTEM SETTING press OPEN to call the submenu 3 Tilt the joystick up and down and move the
22. arameters of current pan tilt When necessary the dome can use these preset parameters to move the camera s targeted direction in a certain pattern User can use these presets easily and promptly by using a keyboard interface The dome can support up to 128 presets Tour The built in function of the speed dome It can appoint settings in advance and arrange presets in a desired order By inserting presets into tour dwell to make the camera tour between these presets Tour order can be programmed each time you arun tour you can set the park time The tour section on the camera can store up to 32 presets e Scan User can easily preset right and left pan limits by using the control menu You can also set the pan speed through this menu as well Pattern The built in function within the speed dome the dome can record assigned movement tracking that are no less than 180 seconds long When running a pattern the dome moves repeatedly according to the recorded programmed tracks A dome can set up to 4 pattern tours Lens position display You can view the position that the speed dome finishes in after completing a self testing procedure by using the lens position display The pan range is between 0 360 and the tilt range is between 0 90 Constant temperature Function The Inner temperature sensor checks the temperature inside of the dome When the dome works at a high temperature the dome will automatically start up the in built fan to
23. ble RS485 control cable As shown in picture 12 above Picture 10 4 Thread the water proof output cable of mini dome through the wall bracket and insert the three screws from the cover board and mini dome into the aperture on the base board then turn 15 degrees clockwise Be sure that central position of the two ear holes of base board and cover board are matched and then lock it tightly using the additional M3 5 screw 2 DOME PERFORMANCE DOME PARAMETERS Power supply DC12V Baudrate RS485 Cosumption Communication Protocol pele D Peleo P Samsung Operation temperature 10 C to 50 C Tilt 90 with auto flip Environmental humidity 0 95 no condensation mae e Limitless variable speed controlling Material CAMERA SPECIFICATIONS Magnification 100times 10 times optical X 10 times digital Video Output Multiple Video Output 1 0Vp p Environmental Temperature 10 C to 450 C Environmental Humidity 0 90 no condensation 2 DOME PERFORMANCE DOME PERFORMANCE AND FEATURES This PTZ camera product has the latest technological features with high resolution colour camera and variable speed pan tilt and multifunction decoder It can reduce the connection and installation process between systematic parts and also can improve the stability and reliability of the system Meanwhile it is easy to install and repair and it has the following advantages contemporary shape smooth rotation low noise and simple
24. cursor to PASSWORD SETTING press OPEN to call System motion controlling menu as the left picture shows SYSTEM SETTING EDIT DOME LABEL INITIAL INFO ty DISPLAY SETUP 4 Input old password Operate joystick move the cursor to OLD PASSWORD MOTION ME CLEAR press OPEN there will be a sign displaying in the front of OLD PASSWORD PASSWORD SETTING The cursor jumps to the first character on the right tilt the joystick up and down CLOCK SETTING COMM SETTING BACK and right to input the other characters press OPEN to save EXIT to set the first password Its option rage is between 0 9 Move the joystick left 5 Input new password Operate joystick move i cursor to NEW PASSWORD press OPEN there will be a sign to displaying in the front of NEW PASSWORD The cursor will jump to the first character on the right using the above instructions the user can ordinally input the password by tilting the joystick up down press OPEN to over PASSWORD SETTING OLD PASSWORD 6 Confirm the new password Input the user s password again using the NEW PASSWORD CONF PASSWORD ENABLE PASSWORD OFF BACK EXIT 7 Start password or not operate joystick move cursor to ENABLE PASSWORD Press OPEN moving joystick up and down switch setup value between ON OFF When set to ON that means the setting password is instructions above If you fail to modify the password correctly you will need to
25. e 4 SYSTEM SETTINGS MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETTING CLOCK SETTING COMM SETTING BACK EXIT COMM SETTING 18 S N 4 7824000058 CONF 4JKAA7824000058 SITE ID 001 COMM SPEED 4800BPS PROTOCOL BACK EXIT VIDO B02 SETUP DOME PARAMETER 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 second Moving joystick up and down to move the cursor to SYSTEM SETTING press OPEN to enter into the next menu Moving joystick up and down move the cursor to COMM SETTING and pressing OPEN to enter into Dome parameter setup menu S N Show Series NO of the dome ex work CONF Use to edit the series NO of the dome so that itis the same as S N series Number SITE ID You can set up the ID Number of the dome address scope 001 255 COMM SPEED Baud rate setup The user can choose 4 different kinds of Baud rate 2400 BPS 4800 BPS 9600 BPS 19200 BPS PROTOCOL Set protocol the user can choose between 16 kinds of protocol PELCO FACTORY DYNACOLOR ISD HUNDA VIDO B02 LILIN KALATEL DIAMOND SAMSUNG PANASONIC SANTACHI VICON MOLYNX VCL SAE A 1 You cannot continue to edit COMM SETTINGS when the above two series Number are not the same 2 After setting up the parameters t
26. e captured during recorded monitoring For example it can shield a window of a bedroom ATM of a bank dome can set up to 24 privacy windows It can be set 24 masking window at mostin 360 surveillance range when the dome rotates down in the level 20 can t set masking window 1 The system enters into the main menu by calling 95 preset or by calling WINDOW BLANKING 9 preset twice within 3 seconds WINDOW NUMBER 01 2 Operate joystick to WINDOW BLANKING press OPEN to enter menu Window EDIT WINDOW blanking ENABLE WINDOW OFF CLEAR WINDOW BACK WINDOW NUMBER choose window number as current privacy window other choices in the menu just aims at current privacy window E EDIT WINDOW edits current window e ENABLE WINDOW permit prohibit current privacy window there two choices ON permits current privacy window OFF prohibits current privacy window e CLEAR WINDOW clear current privacy window after clearing it the window will auto change to the OFF setting 3 Program current privacy window Firstly choose window number then do the following operations a Operate joystick move the cursor to EDIT WINDOW press OPEN to move the image that needs a privacy window to display on the screen b Press OPEN there will be a square displaying on the centre of the screen operate joystick and move the square to the central place that you need to Privacy zone mask
27. e cursor to SHOW PRESET press OPEN the screen will display the current preset Clear current preset move the cursor to CLEAR PRESET press OPEN the current preset will be cleared Edit current preset label move the cursor to EDIT PRESET LABEL press OPEN to enter into editing preset submenu system auto sets label as PRESET XX press OPEN to revise label 1 When running a program display clear preset or edit label you should choose a preset number first to continuously jump over and use the spacebar to replace the deleted characters When you finish to editing a character press Open to go to the next editing character when you finish editing the last character press Open to save Press Close to exit 2 The label may set up to 16 characters which do not need to editing Press Open Characters that are suitable for choose for the label are as follow 0 9 A Zi space 6 FUNCTION SETTING SCAN MAIN MENU Scan has two preset points The camera repeatedly scans between the two points at a stable speed with the same magnification and pan A dome can only carry out a four scan tour SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds click the menu to enter Scan menu as shown in the picture on the left SCAN NUMBER SCAN SPEED SET LEFT L
28. f the varying rays and also auto revise the main lightness to make the pictures more legible This function relates to the camera dome model s built in parameters when wanting to use the black light compensation function When this function is activated the auto adjust is the main operation When the back light compensation When back light compensation is is switched off the background light switched on the image lighting will cause the closest object in view levels will appear more balanced to havealot more shadow 21 5 CAMERA SETTINGS SLOW SHUTTER CONTROL MAIN MENU SYSTEM SETTING CAMERA SETTING 1 The system enters into the main menu by calling 95 preset or by calling FUNCTION SETTING 9 preset twice within 3 seconds WINDOW BLANKING ESL 2 Operate joystick move the cursor to CAMERA SETTING to enter submenu 3 Operate joystick move the cursor Rid SHUTTER setting and press OPEN You will then see the icon in the front of SLOW SHUTTER Move the cursor to the right and make your choice by tilting the joystick up down You can choose from either X2 X4 X6 X8 X10 X12 X14 X16 X24 X32 X64 X128 CAMERA SETTING depending on the light levels and how much you want to be captured by the ZOOM SPEED HIGH camera DIGITAL ZOOM BLC MODE OFF 4 Press OPEN to save SLOW SHUTTER X2 IR CUT FILTER ADVANCE SETTING OPERATION KNACKS BACK EXIT When the dome is being used at night or in a dark env
29. gnification and tilt direction won t change if the speed magnification and tilt direction of the two limits are inconsistent run scan is base on left limit 2 6 FUNCTION SETTING MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT FUNCTION SETTING PRESETS SCAN PATTERNS TOUR ZONES TIME RUNNING BACK EXIT PATTERNS PATTERN NUMBER PROGRAM PATTERN RUN PATTERN CLEAR PATTERN EDIT PATTERN LABEL BACK EXIT EDIT PATTERN LABEL LABELPATTERN 1 BACK EXIT 28 PATTERN Pattern is an built in function of the camera the speed dome can record tracks have to be over 180 seconds long Consists of a series of pan tilt and lens controlling commands You can set the dome up to do up to 4 pattern tours 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick move the cursor to FUNCTION SETTING press OPEN to enter submenu 3 Operate joystick to select PATTERN press OPEN to enter menu Pattern PATTERN NUMBER chooses current pattern number as the current pattern PROGRAM PATTERN define the track of the current pattern RUN PATTERN run current pattern CLEAR PATTERN clear current pattern EDIT PATTERN LABEL edit current pattern label 4 Choose pattern number move the cursor to PATTERN NUMBER press OPEN choose a pattern to be the current pattern the f
30. he setting is effective once you have restarted the dome 9 CAMERA SETTINGS ZQOM SPEND SYSTEM SETTING CAMERA SETTING FUNCTION SETTING 1 The system enters into the main menu by calling 95 preset or by calling 9 WINDOW BLANKING preset twice within 3 seconds EMT 2 Tilt the joystick up down to CAMERA SETTING press OPEN to enter submenu 3 Operate joystick mov Xhe cursor to ZOOM SPEED press OPEN and a sign will appear in front of ZOOM SPEED Move the cursor to right and CAMERA SETTING tilt up down joystick to choose HIGH LOW ZOOM SPEED HIGH DIGITAL ZOOM ON BLC MODE OFF 4 Press OPEN to save press CLOSE to cancel SLOW SHUTTER X2 IR WT FILTER ADVANCE SETTING BACK EXIT 19 5 CAMERA SETTINGS MAIN MENU DIGITAL ZOOM CONTROL SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING 1 The system enters into the main menu by calling 95 preset or by calling 9 preset EXIT twice within 3 seconds 2 Tilt the joystick up down to CAMERA SETTING press OPEN to enter camera setting 3 Operate joystick move the cursor to DIGITAL ZOOM press OPEN to enter digital zoom setting Tilt the joystick up down to choose ON to allow digital zoom CAMERA SETTING to be used When this setting is activated you can then magnify into the video image more closely and be able to inspect the visual information in a larger frame ZOOM SPEED HIGH DIGIT
31. ilts up to 90 degrees You can directly watch the rear view to see that it moves in a portrait 180 degrees In the menu you may set the system parameter setting AUTO FLIP as ON thus you may run this function Park action You can use the menu to set Park time and Park action user may set auto call preset or run tour pattern and scan his is after pointing a few minutes if the dome doesn t run any motions Power up action You can use the menu to set the Power up action after the dome powers up or restarts user may set auto resume motions before power up and auto call preset or run tour pattern and scan CAMERA CONTROL Magnification control The user can adjust the zoom to focus the image on objects close up or far away by using the keyboard controller You can use the Wide Tele function to obtain a panoramic image or the close up view that you need The speed dome supports digital zoom and optical zoom Focus control System defaults Auto focus To get a legible image when the lens changes the camera will auto adjust focus according to the centre of the image user can also manually focus by operating keyboard FAR NEAR function to get desired image When operating the keyboard joystick camera resumes to auto focus The camera cannot auto focus when in the following statuses Target is not at the centre of the image Observing the target close up or far away at the same time can not be clear at the same ti
32. ing conceal c Press OPEN operate joystick to adjust the size of privacy zone move the joystick up and the height will increase move the joystick down and the height will reduced move the joystick to the right and width will increase move the A joystick to left and the width in reduced d Press OPEN to save the current privacy zone setting and the window will auto change to ON at the same time m AA 32 8 APPENDIX DOME MENU INDEX SYSTEM SETTINGij CAMERA SETTING FUNCTION WINDOW BLANKINGj EXIT SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION PRESETS SCAN PATTERNS TOUR ZOOM SPEED HIGH DIGITAL ZOOM ON BLC NODE OFF SLOW SHUTTER X2 IR FILTER ADVANCE SETTING BACK EXIT WINDOW NUMBER 01 EDIT WINDOW ENABLE WINDOW OFF CLEAR WINDOW BACK EXIT ZONES TIME RUNNING BACK CLEAR PASSWORD SETTING CLOCK SETTING COMM SETTING BACK PRESETS EDIT PRESET LABEL PRESET NUMBER EDIT DOME LABEL 0 EDITDOMELABEL IR CUT FILTER SET PRESET LABEL PRESET 01 LABEL SPEED DOME 1 00 SHOW PRESET BACK CLEAR PRESET EXIT BACK IR CUT FILTER AUTO EDIT PRESETLABELj EH IR CUT ON TIME N A M IR CUT OFF TIME N A EXIT BACK INITIAL INFO EXIT SCAN S N 4JKAA7824000058 SCAN NUMBER EDIT SCAN LABEL FIRMWARE V2 50 SCAN SPEED SET LEFT LIMIT PROTOCOL FACTORY SET RIGHT LIMIT DOME ADDRESS 00
33. ironment the image on the screen may be too dark Setting a slow shutter speed will allow more light to be taken into the camera which helps to make the picture more legible 22 5 CAMERA SETTINGS MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT CAMERA SETTING ZOOM SPEED HIGH DIGITAL ZOOM ON BLC MODE OFF SLOW SHUTTER X2 IR CUT FILTER ADVANCE SETTING BACK EXIT IR CUT FILTER IRCUTFILTER AUTO IRCUTONTIME N A IR CUT OFF TIME N A BACK EXIT IR CUT FILTER 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick move the cursor to CAMERA SETTING to enter submenu 3 Operate joystick move the cursor to IR CUT FILTER press OPEN there will be a sign in front of IR CUT FILTER When the cursor jumps to the right move joystick to IR cut filter and a number of choices will be made available as shown below AUTO Default e AUTO IR cut filter mode This means the dome automatically transfers according to sensitivity TIME Set black color time for example can set color image for daylight times and set black for the night It is valid to set the time under Time mode but this will cause other modes to be invalid e COLOR set as color mode BLACK set as black and white mode 4 Press OPEN to save OPERATION KNACKS IR cut filter function uses color in da
34. me Target object s light source is too bright such as spotlight or headlight Target is moving too fast Target area is solid wall Target is too dark or vague Target image is too small 3 FEATURE INFORMATION Iris control System defaults using Auto Iris Camera can rapidly adjust size of Iris automatically when environmental light levels variates this ensures that the video image User can adjust Iris by using the controller keyboard open close function to get required brightness that you need User also can resume auto Iris by joystick operation When controlling the Iris manually the dome locks current position you manually controlled when operating joystick the dome resume auto Iris Auto back light compensation Camera sub area can carry out auto back light compensation Under a strong light background camera will auto compensate light for the darker object and adjust daylight to the bright background In order to avoid making the image mess by the background is too high in luminance and the object is unable to recognize because of darkness thus gain legible image Auto white balance Camera can automatically adjust white balance in accordance with the alteration of background lightness to depict the true colour of the scene Monitor function Set and call preset The preset function which is stored in the dome s memory includes the horizontal angle slope angle camera lens focus position and p
35. ng the 3 x M4 bolts Like picture 4 Picture 1 CEILING MOUNT 1 Dimensions of product as shown below Picture 4 Picture 2 1 INSTALLATION 3 Insert three screws in the mini dome into the apertures on the base board please refer to 1 WAL L MO U NT then turn 15 degrees in clockwise please refer to 2 l Dimension of product shown the picture below Picture 5 Picture 8 4 Use 3 additional M3 5 screws tightly fix camera into ceiling INSTALLING CAMERA 1 Get the products out from the packaging As shown in picture 8 below Picture 6 5 Connect the power cable video cable and RS485 control cable See picture below Power port Picture 8 Picture 7 1 INSTALLATION 2 Make the wall bracket match the model on installation wall and draw the central position of the drill hole As picture 2 2 2 75200 100 00 Picture 11 Picture 9 5 Please make the wall bracket aims at the M8 screw so that the output cable will be locked into the hole of motherboard bracket and use the M8 screw to lock ill four i j e noes oie MG the wall bracket tightly As seen in picture 11 above expanding metal screw with the lashed electric drill on the installation surface and be sure that the installation hole is approximately 75mm in depth Expand M8 metal screw As shown in picture 10 Picture 12 6 Connect the power cable video ca
36. o TOUR DWELL and press OPEN There will be a in front of TOUR DWELL move the cursor to right tilt up down to set park time within the range of 000 255 s 5 Set tour move the cursor to tour dwell 00 00 00 00 and press OPEN The first dwell operation is activated tilt up down joystick to choose a preset number press OPEN and the cursor will jump to the next dwell Press CLOSE and the cursor jumps to the former dwell After finishing the last dwell line press CLOSE to save Press CLOSE to exit If the presets are set on the second line move the cursor to the second line press OPEN to edit continuously When the numerical value is 00 the following presets are invalid A tour can set up to 32 presets 6 Run tour Operate joystick move the cursor to jRUN press jOPENjto exit the menu it starts to run tour PO Preset Number optional scope 00 80 S Movement speed of the dome user can choose between 0 8 the dome run fastest when 8 is chosen slowest when 1 is chosen the dome at is at rest when 0 is chosen TM Stay time setup optional scope 00 60 second Remark the system will leap over the preset automatically when the stay time of one item is setup on 0 The dome will not run the tour of the latter preset when preset or movement speed setup is 0 29 6 FUNCTION SETTING ZONE SETTING A dome may be set up to 8 zones the regional scene can t be overlapped User MA
37. o switch off Auto Flip Press OPEN to save A OPERATION KNACKS When opening the auto flip function hold the joystick in the down position the camera will rotate pan 180 degrees After the camera rotates it will tilt up by 90 degrees You may directly watch the rear view and all processes in a portrait 180 degrees directional path SPEED PROPORTION PAN Operate joystick move the cursor to PROPORTIONAL PAN press OPEN to enter Proportion Pan setting tilt the joystick up down to select option When selecting ON the Proportion Pan will open if selecting OFF this will close Proportion press OPEN to save OPERATION KNACKS When manually adjusting the far focus setup the dome responds at a high speed so if you touch the rocker slightly it may make picture move rapidly thus making it difficult to view image To allow for the sensitivity in adjusting the far focus setup the dome will automatically adjust pan and tilt rotation according how you zoom in or out which make it more convenient to operate manually 13 4 SYSTEM SETTINGS 14 MOTION AUTO FLIP ON PROPORTION PAN ON PARK TIME 005 PARK ACTION SCAN POWER UP ACTION AUTO FAN ENABLED 040 TEMP C F CENT HEAD UP OFF BACK EXIT MOTION AUTO FLIP ON PROPORTION PAN ON PARK TIME 005 PARK ACTION SCAN POWER UP ACTION AUTO FAN ENABLED 040 TEMP C F CENT HEAD UP OFF BACK EXIT MOTION AUTO FLIP ON PROPORT
38. ollowing camera operations perform the current pattern 5 Define current pattern tour move the cursor to PROGRAM PATTERN press OPEN to set pattern track move the image around randomly and then draw the focus The dome cannot perform a tour that is under 180 seconds long You can set the park time magnification and focus to be recorded Press OPEN to save 6 Run pattern Operate joystick to RUN PATTERN and press OPEN to run The dome will continuously and repeatedly record the specific track When carrying out program run clear pattern or editing the label you should choose a pattern number first 6 FUNCTION SETTING MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT FUNCTION SETTING PRESE 5 SCAN PATTERNS TOUR ZONES TIME RUNNING BACK EXIT TOUR Tour is the built in function in the speed dome it will arrange the presets into the queue of auto tour and can set how long it will park at preset Operate auto tour is a process of incessantly transfer each preset One tour can store 24 presets at most 1 The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds 2 Operate joystick move the cursor to FUNCTION SETTING press OPEN enter submenu 3 Operate joystick move the cursor to TOUR then press OPEN to enter menu Tour 4 Set the park time of the preset Operate joystick move the cursor t
39. place away from direct sunlight inflammable explosive substances and etc Please keep it away from environments that contain electromagnetic radiation or objects that produce it Please keep sound ventilation around the device at all times Do not allow the water and other liquid to penetrate into the device if casing has been compromised This series product complies with the IP66 standard specified in the Degrees of Protection Provided by Enclosure Please make sure the CCD CMOS component is away from the radiation of the laser beam device Otherwise it may result in CCD CMOS optical component damage DAILY MAINTENANCE Do not touch CCD CMOS component You can use the blower to clean the dust on the surface of the device You can use the dry cloth with some alcohol or mild detergent to clear if necessary Do not use volatility solvent such as the benzene or thinner or detergent with strong abradability It may result in lens damage or it may adversely affect the device performance If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device 6 ABOUT ACCESSORIES Always use all the accessories recommended by manufacturer Before installation please open the package and check that all the components are included in the package Contact your local retailer ASAP if something is missing in your package CONTENTS INSTALLATIO
40. s 19 DIGITAL ZOOM se canstinepetececarisceneteag cer deer sees 20 ATION cc see cee 21 SILI TEC ON TR seca eis deep eee 22 a a 23 ADVANGED REER ERSE 24 24 BALANOE 25 OMERA MENU 25 G FUNCTION SETTIN 26 PRESET SETTING sei ener nee 26 Eo nm 27 PA TTE crc 28 TOU eee E eee a cee eee ee ese ee 29 ZONE SEI PIN ce 30 TIME FUNN 31 7 PRIVACY ZONE MASKING reinen 32 33 DOME MENO IOE 33 JTROUBLCESPIOCOTING ec E E A E 34 CLEANING THE CLEAR DOWN COVER eo enirn entren retener nen 34 s R485 BUS BASIC KNOWLE atte 35 1 INSTALLATION CORRESPONDING ITEM SHEET 1 Get the products out from the packages As Picture 3 le E Indoor and N outdoor DETAILS OF RELEVANT PARTS 1 1 wall bracket ar 2 base board 3 power cable 4 speed dome MG 5 transparent cover 3 Picture 3 4 5 2 Drill holes and fix base board on the ceiling floor by usi
41. se use neutral detergent Any cleanser for high grade furniture is applicable 34 8 APPENDIX Rs485 BUS BASIC KNOWLEDGE CHARACTERISTICS OF A Rs485 BUS As specified by the Rs485 standard Rs485 Bus is a half duplexed data transmission cable witha characteristic impedance of 120 The maximum load capacity is 32 unit loads including main controller and controller equipment TRANSMISSION DISTANCE OF A Rs485 BUS When user selects the 0 56mm 24AWG twisted pair wires as data transmission cable the maximum theoretical transmitting distances are as follows 2400BPS 1800m 4800BPS 1200m If user selects thinner cables or installs the dome in an environment with a strong electromagnetic interference or connects lots of equipment to the Rs485Bus the maximum transmitting distance will decrease increase the maximum transmitting distance do the contrary CONNECTION AND TERMINATION RESISTOR The Rs485Bus standards require a daisy chain connection between the equipment There must be termination resistors with 120 asthe Picture 2 Please refer to Picture 1 for simple connection D should not exceed 7m RS mi e 1 2 3 4 32 Picture 1 Picture 2 THE CONNECTION OF THE 120 TERMINATION RESISTOR The termination resistor is already on the protocol PCB There are two kinds of connection as shown in Picture 3 This is the factory default connection The jumper cap of swi
42. tchboard is seated on pin 2 amp 3 and the termination resistor 120 is not connected When connecting the 120 termination resistor the user should pull out the protocol PCB and plug the jumper into Pins 1 amp 2 Install the PCB back and the termination resistor should now be connected as show the Picture 3 Connection of1200 setting Factory default setting On means insert the jumper cap Picture 3 35 8 APPENDIX PROBLEMS IN PRACTICAL CONNECTIONS In certain circumstances the factory recommends In some circumstances the user can adopt a star configuration in practical connection The termination resistors must be connected to the equipment 1 and 15 in Picture 4 As the star configuration is not in conformity with the requirements of Rs485 standards problems such as signal reflections lower anti interference performance will arise when the cables are long in the connection The liability of control signals decreases with the phenomena that the dome does not Rs485Distributor respond just responds at intervals to the controller or does continuous operation without stopping the using a Rs485 distributor The distributor can change the star configuration connection to the connection mode stipulated in the Rs485 standards The new connection maintains reliable data transmission Refer to Picture 5 Picture 5 6 Main controller 32h Picture 4 Rs485 BUS TROUBLE SHOOTING A The address and baud rate set
43. ting of dome Cannot control are not in the same as those of the controller A Change the address and baud rate of controller or dome dome self B The and connection of Rs485 Bus is B Adjust the and connection of Rs485 testing incorrect C Make sure the connections are fully seated mechanism C Bad connection D Change Rs485 Bus wires D There is a short circuit in the Rs485 Bus A Poor contact between the Rs485 Bus and the connectors A Secure the connection B One wire of Rs485 bus is broken B Replace Rs485 bus wires C The dome is too far away from controller C Add termination resistors to the system D There are too many domes connected in the D Install Rs485 distributor The dome can be controlled but the operation is not smooth system 36 QS For more information about our analogue Cameras and other available products like DVRs amp accessories please visit our website www adata co uk Alternatively scan this QR code with your Smart phone to be directed instantly to our website
44. tion Keyboard operation OPEN use this to increase Iris opening or when using the setup menu it will allow you to enter into the next menu or setting orit allows you to save settings after finishing setup Close use this to reduce Iris opening or close to cancel FAR Focus to far NEAR Focus to near TELE Increase magnification WIDE Reduce magnification Joystick up When using a menu system this allows you to choose the former menu option or when setting up the camera image it will tiltthe camera up Joystick down when using the menu system it allows you to choose the next menu option when setting up the camera image it will tilt the camera down Joystick left when using the menu system itis equalto the Close function when setting up the camera image it will pan camera left Joystick right when using the menu system itis equal to the Open function when setting up the camera image it will pan camera right 4 SYSTEM SETTINGS Menu and keyboard operation continued Press TELE and WIDE at the same time it means 3D joystick rotates joystick cap Menu operation Back EXITS On 10 Back to the former menu Exit to menu Open some setting Close some setting MAIN MENU SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETTING CLOCK SETTING COMM SETTIN
45. tion and direction before power up e PRESET use preset 1 e SCAN run scan PAT1 run pattern X e TOUR run tour FAN START UP TEMPERATURE The temperature of the dome will rise when the environmental temperature rises as well The fan will automatically start when the temperature reaches a certain level This is to ensure longevity of the dome s lifespan Operate joystick move the cursor to FAN ENABLED then press OPEN the cursor will skip to the last option The user can press OPEN to save the selected choice The default setting temperature of the fan startup is 40 C The user also can enter a new value into the fan startup setting The picture on the left shows the temperature range ranging from 0 60 C The TEMP option can switch temperature between fahrenheit and centigrade HEAD UP MOUNTING SETTING means Head mounting OFF means Head up mounting 4 SYSTEM SETTINGS MAIN MENU SYSTEM SETTING CLEAR CAMERA SETTING FUNCTION SETTING 1 The system enters into the main menu by calling 95 preset or by WINDOW BLANKING calling 9 preset twice within 3 seconds EXIT 2 Tilt up down joystick to select SYSTEM SETTING then press OPEN to enter submenu 3 Tilt up down joystick to select CLEAR press OPEN to enter submenu as left picture shows CLEAR ALL ZONES SYSTEM SETTING e CLEAR ALL PRESETS paff LABEL CLEAR ALL PATTERNS INITIAL INFO e CLEAR ALL TO
46. y and uses black and white at night This function not only guarantees the quality of image but also saves reduces the amount to data to be stored 23 5 CAMERA SETTINGS ADVANCED SETTING MAIN MENU SYSTEM SETTING 1 The system enters into the main menu by calling 95 preset or by calling CAMERA SETTING 9 preset twice within 3 seconds FUNCTION SETTING WINDOW BLANKING 2 Operate joystick move the cursor to CAMERA SETTING to enter EXIT Submenu 3 Operate joystick move the cursor to ADVANCE SETTING and press OPEN to enter submenu as picture to the left shows AE MODE 1 Operate joystick move the cursor to AE MODE press OPEN then tilt the joystick up down to choose AE mode the modes you can choose from ZOOM SPEED HIGH are shown below DIGITAL ZOOM ON BLC MODE OFF AUTO default setting auto Iris mode SLOW SHUTTER X2 BRIGHT brightness priority mode MANE SETTING IRIS iris priority mode BACK SHUTTER shutter priority mode EXIT CAMERA SETTING 2 Choose Iris priority mode IRIS and press OPEN to save 3 Move joystick to the sub choices of AE mode IRIS F1 4 press OPEN to choose adequate Iris press OPEN to save SHUTTER 1 50 this means shutter speed when AE mode is shutter priority this function can be set IRIS F1 4 this means the size of iris when AE mode is iris priority this function can be set AE MODE AUTO BRIGHT F2 0 ODB this means brightness

MINI-PTZ-12X Manual

Contents

Download Pdf Manuals

Related Search

Related Contents