RouterBOARD 192 Quick Setup Guide and
Contents
1. email telephone or fax RMA must be printed signed and enclosed with the shipment also the RMA number must be written on the package itself Parts sent without following the proper procedure will be treated as those not to be repaired or replaced due to the above mentioned conditions Items proved to be free of defects in our lab will be returned to the customer at the customer s expense Those that do meet the warranty repair requirements will be repaired or replaced and returned to the customer s location at our expense extending the warranty term for the time the items are being shipped to and from our facility and replaced or repaired Manual This manual is provided as is without a warranty of any kind expressed or implied including but not limited to the implied warranty of merchantability and fitness for a particular purpose The manufacturer has made every effort to ensure the accuracy of the contents of this manual however it is possible that it may contain technical inaccuracies typographical or other errors No liability is assumed for any inaccuracy found in this publication nor for direct or indirect incidental consequential or other damages that may result from such an inaccuracy including but not limited to loss of data or profits Please report any inaccuracies found to docs mikrotik com See www routerboard com for more information Contact support mikrotik com for support questions rev B 5 Nov 20072. RouterBOARD 192 Quick Setup Guide and Warranty Information Assembling the Hardware First use of the board MiniPcl MiniPCI EN pa i e Insert the MiniPCI cards RouterBOARD 192 provides two MiniPCI slots e Connect antenna cables to the MiniPCI cards e Install the board in a case and connect other peripherals and cables e Plug in power cable to turn on the board Kowaw GNVN Powering The board accepts powering from either of the two power jacks or from the LAN1 Ethernet port e direct input power jacks J9 310 5 5mm outside and 2mm inside diameter female pin positive plug accept 9 28 V DC overvoltage protection starts at 30V e LAN1 Ethernet port J13 accepts 9 28 V DC input at the board higher voltage needed to compensate for power loss on long cables at least 18V suggested from non standard passive Power over Ethernet injectors no power over datalines The board does not work with IEEE802 3af compliant 48V power injectors CAUTION all three power inputs are always active but only one of them may be used at a time to avoid damage of equipment The maximum output of the power supply available for extension cards is normally 6 7W 2 0A Booting process First RouterBOOT loader is started It displays some useful information on the onboard RS232C asynchronous serial port The serial port is set by default to 115200bit s 8 data bits 1 stop bit no parity Note that the devi
3. ce does not fully implement the hardware RTS CTS flow control so it is suggested to try to disable hardware flow control in the terminal emulation program in case the serial console does not work as expected and if it does not help make a new cable using the pinout given in the User s manual The loader may be configured to boot the system from the onboard NAND and or from network See the respective section of User s manual on how to configure booting sequence and other BIOS parameters DHCP or BOOTP configurable in loader protocols allow the RouterBOARD 192 series board to get an initial IP address and provide the address of a TFTP server to download an ELF boot image from It is especially useful for software installation See the User s manual for more information and protocol details Note that you must connect the RouterBOARD you want to boot and the BOOTP DHCP and TFTP servers to the same broadcast domain i e there must not be any routers between them they must be on the same Ethernet switch Extension Slots and Ports e Nine Ethernet ports supporting automatic cross straight cable correction Auto MDI X so you can use either straight or cross over cables for connecting to other network devices The first Ethernet port marked with the PoE label and detached from the 8 port block accepts 9 28 V DC powering from a passive PoE injector The other eight Ethernet ports placed as a block do not support PoE powering e Two Mi
4. niPCI Type IITA IIIB ports with 3 3V power signaling See www routerboard com for more information Contact support mikrotik com for support questions rev B 5 Nov 2007 e DB9 RS232C asynchronous serial port Operating System Support Currently tested operating system is MikroTik RouterOS starting from version 2 9 38 Copyright and Warranty Information Copyright and Trademarks Copyright 2004 2007 MikroTikls SIA This manual contains information protected by copyright law No part of it may be reproduced or transmitted in any form without prior written permission from the copyright holder RouterBOARD RouterOS RouterBOOT and MikroTik are trademarks of MikroTikls SIA All trademarks and registered trademarks appearing in this manual are the property of their respective holders Hardware MikroTikls SIA warrants all RouterBOARD series equipment for the term of one year from the shipping date to be free of defects in materials and workmanship under normal use and service All parts will be repaired or replaced with similar or functionally equivalent parts by MikroTikls SIA during the warranty term except in case the returned parts have mechanical electrical or other accidental or intended damages caused by improper use or due to wind rain fire or other acts of nature Parts or systems must be shipped pre paid to our facility in Riga Latvia All items must have a Return Material Authorization RMA which you can get by contacting us via
Download Pdf Manuals
Related Search