Conforming Meter List Application
Contents
1. M O Hab A Conforming Meter List Application Market Operator Mail the completed form including all supporting documents and materials to Independent Electricity Market Operator Station A Box 4474 Toronto ON _M5W 4E5 Attn Metering Technical Group Courier the completed form including all supporting documents and materials to Independent Electricity Market Operator 655 Bay Street Suite 410 Toronto ON_M5G 2K4 Attn Metering Technical Group All information submitted in this process will be used by the JMO solely in support of its obligations under the Electricity Act 1998 the Ontario Energy Board Act 1998 the Market Rules and associated policies standards and procedures and its licence All submitted information will be assigned the appropriate confidentiality level upon receipt Terms and acronyms used in this Form that are italicized have the meanings ascribed thereto in Chapter 11 of the Market Rules If mailing your package please allow 5 business days for delivery to the JMO Questions regarding the application form should be directed at email meter group theIMO com or the JMO Help Centre number 905 403 6900 1 888 448 7777 The Independent Electricity Market Operator IMO requires all revenue meters to conform to the standards in the Wholesale Revenue Metering Standard Hardware The IMO publishes a list of conforming meters on its web site www theIMO com called the Conform2. VARs received by the IMO grid 4 5 V per phase if applicable eptional for alternate but 5 6 7 required for main main meter 6 I per phase if applieable optional for alternate but 8 9 10 required fermain_meter C 2 MV 90 PARAMETERS 1 Indicate the value or setting for each of the MV 90 parameters below 2 Provide export MV 90 Master File on disk with this application form 1 Intervals hour e TIM Name and Number Baud rate opema o 7 Password to synchronize time peme o Page Gof 11 PublicIMO FORM 1179 v 2 1IMMO FORM H79v 2 HMO FORM H79 REV 04 12REV 04 12REV 02 93 i a 9 Unit of measure for each channel Meter Multiplier for each channel 1 1 0 1 2 Number of Dials for each channel 3 Start Meter Reading for each channel 1 1 14 Encoder Type for each channel 10 Pulse Multiplier for each channel IMO FORM 1179 v 2 1 FMO FORM H79 y 2 IMO FORM H79 20 Public REV 04 12REV 04 12REV 02 93 C 3 DIAL UP CONFIGURATIONS Provide a description with diagrams attach additional pages if necessary of dial up configurations supported for multiple meter connections i e master slave multi drop line router If these descriptions and diagrams are already available in the meter s technical or user manual provide page references below Description Reference Manual pg no Page 8 of 11 PublicIMO FORM 1179 v
3. powers meter electronics then disconnect one of A or C phases If C phase powers meter electronics disconnect one of A or B phases Does not matter which phase is disconnected if meter supplied at auxiliary power terminals 8 Substitute B or C for A if B or C powers meter electronics Page 10 of 11 PublicIMO FORM 1179 v 2 1MMO FORM H79v 2 HMO FORM H79 REV 04 12REV 04 12REV 02 93 Part Task Applicant IMO in Part 10 Note results 12 Communicate Set up master and slave meters for remote Interrogate slave meter channels with slave interrogation and registers meter PART E ATTACHMENTS LIST FOR ATTACHED DOCUMENTS DISKS OR CDs PART F CERTIFICATION By signing below you confirm that all information provided in this application is correct and is signed by an officer of your organization usually the Primary Contact with signing authority for agreements and contracts Name Please Print Signature IMO FORM 1179 v 2 1 FMO FORM H79 y2IMO FORM H79 4 2 0 REV 04 12REV 04 12REV 02 93 Public
4. 2 1MMO FORM H79v 2 HMO FORM H79 REV 04 12REV 04 12REV 02 93 C 4 POWER SOURCE CONFIGURATIONS If submitting an alternate meter in this application or a main meter which can be installed as an alternate describe how the meter meets the Self Power requirement specified in Section 5 4 of the Wholesale Revenue Metering Standard Hardware If these descriptions and diagrams are already available in the meter s technical or user manual provide page references below Reference Manual pg no 1 2 3 IMO FORM 1179 v 2 1 EIMO FORM H79 4 2 IMO FORM H79 42 0 Public REV 04 12REV 04 12REV 02 93 PART D FORMAT OF THE DYNAMIC BENCH TEST This part provides a sample format for the Dynamic Bench Test which the JMO conducts in conjunction with the applicant after this application and all supporting documents have been received and deemed satisfactory by the JMO Applicants should refer to the JMO procedure Conformance Monitoring Conforming Meter List for more information on the Dynamic Bench Test Applicants must indicate a preferred testing time for the Dynamic Bench Test in Part A of this application Part Task Applicant IMO 1 Set up load Install a 3 element meter on the test bench Interrogate meter channels and Connect telephone line to the meter registers Apply 120 volts 2 5 Amps at 0 5 Power Factor Run meter at load for minimum
5. AIN AND ALTERNATE METER REQUIREMENTS CONTINUED Main Meter Yes No Comments 1 Measurement Canada Approval Number provide number 2 Firmware Version Number provide number 3 ANSI C12 20 0 2 Specification submit test results 4 o Cine ee 2 i a E detest ae ee 45 4 Channel Wh DEL amp REC and VARh DEL amp REC Interval Data 56 Encoded Cumulative Registers all Watts amp VARS 67 Ih per Phase Channel 78 V h per Phase Channel 89 5 Minute Interval Channels 940 35 Days of Data Storage 104 35 Days of Battery Back up 112 100 Event Log 123 Two Passwords minimum 134 Minimum 7 Alphanumeric Char for Device ID 145 Time Clock Resettable by MV 90 156 Compatible with UTS MV 90 Software 167 Maintain Eastern Standard Time 178 Modem 9600 BAUD external modem acceptable 189 ANSI Optical Port OoOjJOOO0OOO0000 0 0 0 010 0 O0 0oiopoooopooodo jO 0 0 0 010 a A Optional Distributed Network Protocol DNP 3 0 compatibility E C B Does the Meter support Multi drop or Master Slave configuration If Yes complete Part C 3 L CI 2 DELivered and RECeived fromthe MO controlled eridinthe case of puretoads i h e S Test results require a signature of a professional engineer An in house engineer is acceptable DELivered and RECeived from the IMO controlled grid in th
6. No Mailing Address E mail Address Secondary Contact Name Position Telephone No Fax No E mail Address Meter Manufacturer Model Serial Number of Meter Requesting Main Meter Conformance _ Requesting Alternate Meter Conformance _ Please note that a main meter automatically qualifies as an alternate meter Suitable for Generator Loads L Suitable for Pure Consumption Loads E Please note that a generator load meter automatically qualifies as a pure consumption load meter Dynamic Bench Test Procedure Please provide the preferred week to perform the Dynamic Bench test Allow at least two weeks to process this request 3 I request the week of Page Jof 11 PublicIMO FORM 1179 v 2 1MMO FORM H79v 2 HMO FORM H79 REV 04 12REV 04 12REV 02 93 PART B MAIN AND ALTERNATE METER REQUIREMENTS Use Part B of the application to verify that the meter meets each JMO requirement listed for main or alternate meters Check Yes if the meter does meet the requirement or No if the meter does not meet the requirement If No is selected explain why in the Comments column Applicants should review both checklists to confirm that the appropriate meter category Main or Alternate has been selected for this application IMO FORM 1179 v 2 1 FMO FORM H79 y 2 IMO FORM H79 20 Public REV 04 12REV 04 12REV 02 93 PART B M
7. andard Time O O 158 Modem 2400 BAUD external modem T T acceptable 169 ANSI Optical Port OoOlo A Optional Distributed Network Protocol DNP o T 3 0 compatibility B Does the Meter support Multi drop or Master Slave configuration O O If Yes complete Part C 3 4 Test results require a signature of a professional engineer An in house engineer is acceptable DELivered and RECeived from the IMO controlled grid in the case of generators or parallel transformers DNP compatibility is not an IMO requirement for revenue metering but an optional feature If the meter does have DNP compatibility the IMO will request a sample meter for SCADA testing at a later date IMO FORM 1179 v 2 1 FMO FORM H79 y 2 IMO FORM H179 20 Public REV 04 12REV 04 12REV 02 93 PART C Part C 1 Channel Assignment describes the JMO meter channel assignments All revenue meters operating in the IMO administered markets are recommended to adhere to these channel guidelines Applicants must complete Part C 2 MV 90 Parameters to allow the JMO to communicate with the meter during the Dynamic Bench Test with the MV 90 application Complete parts C 3 and C 4 if applicable C 1 CHANNEL ASSIGNMENT GUIDELINES Interval Data Normal Channel 1 Watts delivered by the IMO grid 1 2 VARs delivered by the IMO grid 2 3 Watts received by the IMO grid fappleablee tor4 3 channels 4
8. e case of generators or parallel transformers DNP compatibility is not an JMO requirement for revenue metering but an optional feature If the meter does have DNP compatibility the IMO will request a sample meter for SCADA testing at a later date Page 4of 11 PublicIMO FORM 1179 v 2 1IMMO FORM H79v 2 HMO FORM H79 REV 04 12REV 04 12REV 02 93 PART B MAIN AND ALTERNATE METER REQUIREMENTS CONTINUED Alternate Meter Yes No Comments Bolded words indicate that requirement differs from main meter requirement Do not complete this page if Main Meter checklist opposite has been used 1 Measurement Canada Approval Number Oo o provide number Firmware Version Number provide number O O 3 ANSI C12 20 0 5 Specification submit test T T results Chame ah Se te SS ioe shige ea tat HIE 54 4 Channel Wh DEL amp REC and VARh DEL amp T T REC Interval Data 56 Encoded Cumulative Registers all Watts amp T T VARS 7 OptienaH h perPhase Channel EIE Optional V hper Phase Channel BEIE 69 5 Minute Interval Channels O O 719 10 Days of Data Storage O O 844 10 Days of Battery Back up O O 942 Alarm Flags O O 103 Two Passwords minimum O O 114 Minimum 7 Alphanumeric Char for Device ID O O 125 Time Clock Resettable by MV 90 O O 136 Compatible with UTS MV 90 Software O O 147 Maintain Eastern St
9. ing Meter List This list is accessible to all participants in the marketplace Applicants should review the JMO procedure Conformance Monitoring Conforming Meter List before completing this application form This procedure can be downloaded from the JMO web site Applicants are required to complete Parts A B C and F of this form Use Part A to complete general information about your organization and the meter being submitted for conformance acceptance Use Part B to identify if specific features of the meter meet IMO standards Use Part C to provide information required by the IMO to communicate with the meter and to provide information about dial up and power source configurations Part C also contains channel assignment guidelines for the meter which the Applicant is required to follow IMO FORM 1179 v 2 1 FMO FORM H79 2 IMO FORM H179 20 Public REV 04 12REV 04 12REV 02 93 Part D is for reference only and describes the format of the Dynamic Bench Test This test is conducted after this application and all supporting documents have been reviewed and accepted by the JMO at a test site chosen by the applicant Applicants are required to submit one form per manufacturer meter and model Please include with the application any user guides or technical specification documents available for the meter PART A APPLICANT INFORMATION Organization Name Primary Contact Name Position Telephone No Fax
10. of 31 minutes 2 Remove one Disconnect one of B phase voltage or Interrogate meter channels and potential C phase voltage for 10 minutes registers 3 Remove all Disconnect A phase voltage and Interrogate meter channels and potentials remaining voltage phase for 10 minutes registers 4 Reconnect all Reconnect A B and C phase Interrogate meter channels and potentials voltages registers 5 Remove one Disconnect one of A or B or C Interrogate meter channels and current phase currents for 10 minutes registers 6 Remove all Disconnect remaining two phase currents Interrogate meter channels and currents for 10 minutes registers 7 Reconnect all Reconnect A B and C phase Interrogate meter channels and currents currents registers 8 Reverse all Reverse A B and C phase currents Interrogate meter channels and currents for 10 minutes registers 9 Remove one Disconnect one of A or B or C Interrogate meter channels and current phase currents for 10 minutes registers 10 Reset time Set up meter to be effectively Attempt to reset time using each Measurement Canada sealed Supply password Note results read only read plus synchronize time and read plus write passwords 11 Password Access meter with valid_and Security Ainvalid versions of each passwords 7 Assumes A phase powers meter electronics If B phase
Download Pdf Manuals
Related Search