LCTSD318 LCTSD326 LCTSD336
Contents
1. After to have finish the connection and adjustment necessary close the access door of the connection board and hook up the speed dome block of in the place of house Note before to proced logn out the security Pay attention to the direction of the quick courcins Control the lever of hook and unhook are correctly insert For end the installation i twill be now hook up sufficient the see through dome and fix the closing screw CP I Note Put the dome with the prescribed centre in to fixing e correspondence h 0 Ih I 4 www hrcctv com m User Manual Ler y FI LCTSD318 326 336 3 Menu Configuration To understand the potentiality of LCTSD camera high speed dome system see the followed illustration Video wiring note come true with usual coaxial cable or twisted cable and the BUS RS485 for the Speed Dome management At the RS485 BUS fin place too recorder DVR and on the BUS is possible to put on LCTspeed dome HR DVR HR keyboard HRKB001 and HRKB001NET By these devices is possible to manage and setup the Speed Dome Doppino Twistato Rs 485 Cavo Segnale Video Analogico INTERNET 3 1 Menu Operation Use the console Joystick or the HR DVR directional key up and down to move in item of menu Use right Joystick or the HR DVR directional right key to select vary it2. LCTSD326 LCTSD336 LCTO804 ver 1 0 www hrcctv com User Manual 1 gr LCTSD318 326 336 mU BO NORME GENERALI DI SICUREZZA General safety recommendations Sicurezza delle persone Safety warnings devono essere lette e seguite prima che il LIT prodotto sia messo in funzione E Precauzioni particolari Rispettare tassativamente l ordine delle istruzioni di installazione e collegamento descritte nel manuale Verificare le indicazioni riportate sulla targa di identificazione esse devono corrispondere alla vostra rete elettrica di alimentazione ed al consumo elettrico Conservate le istruzioni per una consulta futura Read and follow the instructions Read the installation instructions before connecting the system to its power source Follow these guidelines to ensure general safety In order to prevent injury burns or electrical shock to yourself and others follow the connection instruction plan carefully Leggere e seguire le istruzioni Tutte le istruzioni per la sicurezza e per l operativit Sicurezza del prodotto Product Safety Non posizionare in prossimit di liquidi oppure in un ambiente ad umidit eccessiva Non lasciare penetrare del liquido o corpi estranei all interno dell apparecchiatura Non ostruire le griglie di aerazione Non sottoporre all esposizione dei raggi solari oppure in prossimit di fonti di calore Do not use the product in a wet location Never push a foreign object through an o
3. Prot m Mur AI Fi EE ANA Pe 4 L se t 13 S 1 a 2 7 x a amp 3 v T z e gt y a y 5 EA s ri wes da A 1 l vin E ERA d a PIA 7 E ri 1 DE mM n x 7 g The DIP SWITCH have two functions Use for setup the switch value Baud Rate and Protocol and use for unit address Put out the camera before switches adjustment then put on Next table show the switch position and function The switch 7 and 8 of DIP Swicth 1 SW1 be useful to setup speed of the BUS that has be common at all RS485 connect devices SW 1 Baud Rate DIP 7 8 Switch position parameter choice Ea pata Dit Stop bit 9600 19200 The factory start up is 4800 EN 4800 EN Dag 8 a www hrcctv com User Manual 1 CIE LCTSD318 326 336 The protocol of communication that need to use is assigned by DIP Swicthes 1 2 3 4 5 6 SW 1 Protocol DIP 1 6 Switch Position Protocol Switch Position Pelco PD Default Pelco PDC i The factory start up is Pelco PD Second the next table that consent to obtain 254 different address 1 at 254 all switches of the second DIP Switch assign the address of the camera Each camera on the bus need to assign a different address that is put in to the keyboard SW 2 Do reference at appendix A for the complete address list For stave off accidental push down to the Speed Dome lock on the block on the security hook
4. 8 1 ok 180 Tilt VBS 1 0Vp p sync negative Y C output IP66 10 50 C 95 UR 24VAC nominal 18 30VAC 10VA min 90VA max heating up Italian English French Spanish 3 1 Kg 325mm H x 220mm 9 x 290mm P Sony FCB EX480CP 1 4 type EXview HAD CCD Approx 440 000 pixels 18x Zoom f 4 1mm wide to 73 8 mm tele F1 4 to F3 0 12x 216x with optical zoom 48 wide end to 2 8 tele end 35mm wide end to 800mm tele end 0 7 lx typical 50 IRE Sony FCB EX980P 1 4 type EXview HAD CCD Approx 440 000 pixels 26x Zoom f 3 5 wide to 91 0 mm tele F1 6 to F3 8 12x 312x with optical zoom 55 wide end to 2 3 tele end 320mm wide end to 1500mm tele end 1 0 lx typical 50 IRE Sony FCB EX1000P 1 4 type EXview HAD CCD Approx 440 000 pixels 36x optical zoom f 3 4 mm wide to 122 4 mm tele F1 6 to F4 5 12x 432x with optical zoom 57 8 wide end to 1 7 tele end 1 5 m at tele end 1 60s mode 1 4 lux typical F1 6 50 IRE 1 4 s mode 0 1 lux typical F1 6 50 IR o Www hrcctv com pas User Manual a Ge LCTSD318 326 336 1 2 Side identification A x pi TE 7 NE MESS pz eon Wil a amp TET EET ERT 4 AU et y PU yp ep of the cen ej bd g e OEE iat dl Fd Ws lef le lle Lo Tara
5. EU m Was Y a arar PA PM TM M UM mI 4 q de Mot i Bracket of wall to fix Threaded inside attack Drip Inside custody Security hook Fan Heating up plate Hook up lever and quick shell out 9 Hook tack on of security 10 Speed Dome block off 11 Objective 12 camera module 13 Transparent cover 14 Connection card 15 Inside shell blot out ON U www hrcctv com User Manual 1 LCTSD318 326 336 CHA 2 Installation 2 1 Preparations Precautions e Qualified and experienced person can carry out the installation In many countries and areas licensed people is required e Before the installation and connection put off the camera e Do not putin the camera near to the air vent of the air conditioner e To wall montage lay up for LCTST300M bracket e Installation surface e Precaution disassemble can only be carried out by qualified people e For fixing to wall make the necessary article of tool shop ad es plug anchorage screw etc 2 2 Bracket assembling Used screw darts or apt to similar to fix the bracket on the surface of installation 1 Use bracket to marke the mounting position on wall fig 1 2 Fix bracket on the wall and put cables through the wall inside the bracket fig 2 85mm 85mm Aa WLU ww t n Fig 1 Fig 2 2 3 Connection All series LCTSD Speed Dome camera have got one cable for video signal which end female BNC connector terminal
6. Fig 4 3 connect cables Connect these cables into the relative connector relative wl TUBI US 07 10 08 I Ty ms Y n r E ont cneasa 0 44410004 E a 5 Ja AM fa Ex p pe p SADA FERRRERA eve sbe 063 te 7 mww Ww e 14 C15 T3073 AAA AA A Video signal BNC female connector B RS485 A and RS485 B terminal box Open the screw of clamps put in the cables and close Attention to the polarity electric wires RS485 A RX and RS485 B RX in the connection with the control device control keyboard DVR www hrcctv com User Manual pan LCTSD318 326 336 Tal D IN OUT alarm clamps 8 in put with 1 common of reference the in put must to pilot at clean contacts 1 output alarm to relay Common NC e NO max 30V 1A 2 4 Switches adjustment For access to the 2 DIP SWITCHES reverse the block of Speed dome pag 5 do E Y 2 E ba LE A 4 be x gt e f n hy NIS X ta T ty 1 Nr p ARN CS pores r 1M VI Po sr P Pek v UC C T ba sts ix Y D LAD a i rr STA z 1 T NL ei rune fo gt sa 1 8 address vga 5 PRA ing i44 8 Tal E 5678 t 1 a Mir 243 b veto As UN WIr Ew EIA te A Ln S ode S A lt ua 7 te ak gs wi Se PROS peer e N 1 1 th 66 ig Chi A r 4 7 gt IER 44 ES
7. 0 Auto running Automated SOU usais ais iia 16 3 9 Privacy mask Privacy Aree setup cccccccccccsccccccccccssccccccccsssssccccssessesscccssseseseeees 18 32410 Alarm Alarm SECU eca O O DS 19 4 APRENDI a 21 www hrcctv com MEN User Manual 1 e LCTSD318 326 336 1 Introduction 1 1 Technical specific Specifics Preset Tour Cruise Pattern Horizontal Movimento OSD password Proportional Pan Tilt Day night S N Ratio Electronics shutter White bilance Gain AE control Back Light Compensation Privacy Zone Input output Alarm Autorunnig Auto Flip Video Output Security grade Environmental temperature Power Uptake Language Weight Size With Wall brachet LCTST300M LCTSD318 camera Module Image Sensor Pixels Lens Digital Zoom Vision horizontal Min functioning distance Min Lighting LCTSD326 camera Module Image Sensor Pixels Lens Digital Zoom Vision horizontale Min functioning distance Min Lighting LCTSD336 camera Module Image Sensor Pixels Lens Digital Zooml Vision horizzontale Min functioning distance Min Lighting Details 220 4 max 27 Preset 4 4 360 speed 300 sec Ok Ok Auto Color Night select gt 50dB 1 1 1 10 000 sec 22 steps Auto ATW Inside Outside One Push Manual Auto Manual 3dB 28dB 2dB steps Auto Manual Priority Mode Bright EV compensation Back light compensation On Off 8
8. AS eee st a O 3234 aaa Meee on on pon on on Ne on o __ ON ON ON e gt NIN oo ON SO Sana CI aaa mal aa moo on alal ala la e wl nl o ON qa 32487 7 1 Meee ON tN ON on ONE ON ON ON 2311 ON ON on ON ON ON on aa ON ON ON ON ON ON meee ON on ON on ON ON ON EMEN ON ON ON ON ON ON ON www hrcctv com 0002 oe css TAS ufum aci AL eee coa RN 5 gr User Manual Us B LCTSD318 326 336 Technical specifications can be modified without any preliminary notice This manual may not be reproduced in whole or in part except brief quotations in articles or magazines without the written permission of HR EUROPE www hrcctv com User Manual Ler y FI LCTSD318 326 336 Go HR EUROPE s r l ROMA sede legale e amministrativa Via Giulianello 1 7 00178 Roma ITALIA Tel 39 06 7612912 Fax 39 06 7612601 TORINO sede operativa Via G B Feroggio 10 10151 Torino ITALIA Tel 39 011 453 53 23 Fax 39 011 453 70 49 SHANGHAI ufficio di rappresentanza Minhang Residence Room 506 N 50 Jinzhu Road 200336 Shanghai CHINA Tel Fax 86 21 62086781 e mail infoshangaiehrcctv com e mail infoehrcctv com web www hrcctv com Codice Fiscale e Partita IVA 06397551000 Iscrizione R E A 966880 9 ag 24 tt www hrcctv com
9. ON ON ON ON ON 1133 ON ON ON ON 114 ON N ON ON BEKES ON ON ON ON ON ON ON ON ON E NOVO EC 0 E BA www hrcctv com 29 2 I A 1 i RESTI ERE a User Manual e LCTSD318 326 336 a e eee ON pon yoo on pon pp 0N Meee o on Op 0 qa on X on EENE OSSO ue MM 9 AA 1 Emi CL a Taal Tama ar ON o on on NN ON on oN ON MERA ON on on on ON on ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON 184 ON ON ON ON 7 ON pon o ON ON ON ON ON 1 ON on ENT o ON ON ON ON 1 ON ON on oN ON ON ON ON ON ON IS Ow ON on on on ON ON MES ON on ICA EREMO 019 LL 1 9 8L oo 1 1 111 911 8129 9 96 IU it 7296 a aa NEN ON ON ON oN on EMEN ON JJ ON ON 9 M 22 EM Tw a alm ml alm al Tala on on fF oN ff ON fT ON A _L mini lei MOT oi aa aa oo ON ON on on ON on MEME ON ON ON ON __ ON ON 221 eo on oN 9 0 0 AAA E 1 9 17 ar 1 8 55 O IS IS a qa aol u
10. Run Back Zone Park Time Park Action Back Select lt Zone gt to enter sub menu and control 6 zone at personal name and passage speed lt Zone Number gt Select zone name lt Name gt Put desired zone name lt Left limit gt In here move the camera to the desired left limit lt Right limit gt In here move the camera to the desired right limit lt Remove gt Select to delete the current Zone lt Speed gt Set the current scanning speed Range value is 1 255 lt Run gt To start scanning the current zone Park Time This function let the system automatically run on assigned function after a specific period of idle time Select time between 1 and 255s to arm function Select OFF to disable this function Park Action Park action refers to the function that system will automatically run when park time is up The function liable to be constituted from the call preset run tour cruise or pattern setup 3 9 Privacy mask Area privacy setup System Mask Number Lens Mask Setup Camera Remove Mask Pan Tilt Remove All Auto Running pes Privacy Mask Alarm Exit www hrcctv com pas User Manual tap LCTSD318 326 336 Privacy Mask Select lt Privacy Mask gt to enter sub menu and control 8 masking zones lt Mask Number gt Select mask zone number lt Mask setup gt Set the position and size of the masking zone Before to mask make sure with camera just be position to the
11. anually controlled Point D Off Select this option camera do not make any automated control that is necessary operator intervention jag 14 i www hrcctv com 1 pas User Manual uns B LCTSD318 326 336 D Autofocus Time In this menu is possible disarm arm Off If on is up select seconds lt 0 255 gt In here the dome can be manually controlled this function consent to restore auto focus automated After user time Autoiris Time In this menu is possible disarm arm lt Off gt if on is up seconds lt 0 255 gt In here the dome can be manual IRIS this function consent to restore auto IRIS automated after user time ALC Select value between 0 and 31 for electronics shutter standard opening to define The parameter is programmed if IRIS manual control is up Default value 23X NOTE Keep the default value is strongly recommended Day Night Arm lt Auto gt or disarm lt Off gt the Day Night function lt Auto gt The Dome changes automatically color to black from white second environment lightness lt Off gt The Dome always as a color camera Use this option in light environment 3 6 CAMERA Camera Setup System Sensibility Lens Freeze Mode Camera White Balance Pan Tilt BLC Mode Auto Running Back Privacy Mask Alarm Back Sensibility In This menu is possible to change setup time of the shutter to get the light that has to pass on the CCD sensor time is most high to open mo
12. behind input password so that new password can be input If old password is not correct cursor goes back to front of input password Confirm PW gt Confirm new password PW protection On Off Arm or Disarm the password request to access system and save Preset Note Default password of the system is 123456 E Default In this menu is possible to restore factory default settings of Speed Dome Password Arm the password protection and input user password Password asiaa Setup Restore default and remove the configurations Setup Back System reboot Select lt system reboot gt the dome reboot immediately to make autotest cycle 3 5 Lens setup Zoom Speed System Digital Zoom Lens Joystick AF AT Camera AutoFocus Time Pan Tilt Autolris Time Auto Running ALC Privacy Mask Day Night Alarm Back Exit Zoom Speed Set the zoom speed level to high or low Digital Zoom Arm lt On gt or disarm lt Off gt digital zoom Joystick AF AI Select function wanted between lt AF Al gt lt Iris lt Focus and Off lt AF Al gt Select this option camera can put automatically mode auto focus and electronics shutter lt Iris gt Select this option camera can put on mode automatically only electronics shutter but focus can also be manually controlled Point E Focus Select this option camera can put on mode automatically only focus up but electronics shutter can also be m
13. box to connect power PTZ and auxiliary alarms Be needed 3 types of wiring for structure set up of Speed Dome e Power 24V to alternate current e Video signal the camera makes one commun composite video signal Use the RG59 coaxial cable for distance 120 m while for higher distances use video balun to transport the video signal up the UTP cable LCT202T LCT202R LCT302T LCT302R e PTZ The LCTSD series camera use one RS485 serial BUS connection with twisted cable Use only twisted cable RS485 Bus can stringently to 1200 m of length and she connected to falls device The section of the cable depends of the connection length one section of 0 5 mmg is sufficient for a short distance while to use section higher of 1 mmq or 2 5 mmq is necessary link up long distance max 1200 m use screen cable in the wiring execution Go to connect the camera and console in cascade that is entering and exting from the RS485A and RS485B do not invert the cable A B during the equipment connection on the first and last device is necessary to connect the resistance for the correct functioning of the RS485 the resistance value to use is 1200hm proceed 1 open the access door of connection inside of the custody fig 3 2 screw the custody to the bracket to conduct cables through the hole on top of the housing fig 4 a PO uL OX Www hrcctv com pas User Manual a Cow BN LCTSD318 326 336 85mm Me uw Fig 3
14. cover zone Up on in menu is not possible to move the dome lt Mask Remove gt Remove current mask lt All Remove gt Remove all mask zone 3 10 Alarm Alarm setup Alarm In 1 Alarm In 2 Alarm In 3 Alarm In 4 Alarm In 5 Alarm In 6 System Lens Camera Pan Tilt Auto Running Privacy Mask Alarmi Alarm In 7 Alarm In 8 Exit 1 Arm Disarm Interval lt s gt Back Back www hrcctv com User Manual pan LCTSD318 326 336 uns B Alarm Select Alarm to enter sub menu and control input and output alarm Alarm In 1 8 For each input alarm is possible associate preset or select 1 to the 4 tour cruise or pattern setup Output 1 gt ON OFF Select arm disarm output relay Arm Disarm Arm or disarm the alarm system Interval Set the time after which the alarm will be reset During setup this time output relay stays up o Www hircctv com User Manual LCTSD318 326 336 4 APPENDIX DIP SWITCH AND ADDRESS SETTING CHART 79 ON ON ON ON ON 80 ON ON magi ON TE tae oO O E ON Ee eee ee eee eee 1 1 1 ea ei ON TE NT MS ON O_O O o on 0 1001 on ON n on on py Oo ov on Oss nl on 9 1 MEA on on on Q0 o oso ON on ON ON ON ON ON 109 ON ON ON __ ON ON 110 ON ON ON ON
15. djustment 4 Tours lt Tour Number gt Set tour number lt Interval gt Select standard dwell time of preset status lt Edit gt Selected this in the sub menu is possible select preset order looked and its length of time lt Test gt The current tour test lt Run gt To run the current manual tour Cruise Preset Tour Cruise Pattern Cruise Number Left Position Right Position Speed Run Zone Back Park Time Park Action Back Select lt Cruise gt to enter sub menu and control 4 Cruise lt Cruise Number gt Set Cruise number lt Left Position gt In here move the camera to the desired limit of left position lt Right position gt In here move the camera to the desired limit of right position lt Speed gt Set the scanning speed Range value is 1 255 lt Run gt To run the current manual Cruise www hrcctv com User Manual Ler LCTSD318 326 336 mm 8 D Pattern Preset Tour Cruise Pattern Pattern Numbe Record Test Run Zone Back Park Time Park Time Back Select lt Pattern gt to enter sub menu and control Pattern lt Pattern Number gt Select Pattern record number lt Record gt Here move the camera to desired positions to recording really passage lt Test gt The current pattern test lt Run gt torun the current manual Pattern E Zone Preset Tour Cruise Pattern Zona Number Name Left limit Right limit Remove Speed
16. em or go in sub menu Use the console Joystick or the DVR HR directional key up and down for vary parameter Use left Joystick or the HR DVR directional left key to give the OK at programming e Select the back item or exit for return to the past menu or exit to the OSD Recall 95 preset or call consecutive 2 times preset 1 with in 5 second the OSD menu it may be activated Preset recall it may be at keyboard or HR DVR 288 10 www hrcctv com pas User Manual tp l LCTSD318 326 336 3 2 Boot up Screen When the Speed dome power on the device wants a few seconds for boot up information will display on screen and will conduct self testing Will show on the screen until booting success Protocol display the protocol in use set up by DIP Switch 1 Protocol Pelco PD e Com display the parameter of communication set up by DIP Switch 1 Com 4800 N e address display the Speed Dome address assigned set up by DIP Switch 2 address 001 e Model display the model in use of the three available LCTSD318 LCTSD326 Model LCTSD318 LCTSD336 Version 1 01 e Version firmware version Booting up www hrcctv com User Manual 1 e LCTSD318 326 336 oo iw BH System setup pag 13 e Site Info Dome ID Name broadcast address e Display Setup Screen display e Boot up Screen Display boot up information Boot up screen On Off P prey P Password Default e Password Change password System Reboot e Default Restore fac
17. lazione inadeguata This warranty is valid for 2 years from the date of purchase obtained only against presentation of the original invoice cash ticket issued to the customer by the retailer Warranty repair service is excluded if damage or defects have been caused by Improper use incorrect storage dropping or shocks corrosion dirt water handing or operation of the product as referred to in the users manuals www hrcctv com 1 e User Manual Cree LCTSD318 326 336 SUMMARY 1 OCU CUNO aia 4 1 1 Technical SPECIES aa 4 La ee P 4 Fabr m E Y 4 Tuis M o II O 4 PRE TET T TT Tm 5 MSAA O sacra sn cosines RU me 6 FN PI CBT a ON n Dom 6 2 2 1136165 assembling on 6 253 COMMCCUION S 2 00922999999299990 90092999 8999942 0099 90 0000098094 1099 09900909990 9009 9090 0 9 900 9099 40 09992 0098 6 2 4 Switch 3011511111 8 3 Menu CONT GUAM ON usc corn atodos 10 3 1 Menu Opera Oscars UT 10 3 4 DOODUD SCI Be Ln 11 3 3 Mend explana lOM RO 12 54 13 3 9 bens ODUCS S E rra aia 14 3 6 CAMERA Camera SOLUD assim pidio 15 ENTE FEV LT EA uro fr I 16 3
18. n Off To display the preset name Cruise Name On lt Nome Cruise gt On Off To display the Cruise name Pattern Name On lt Pattern Name gt On Off Arm or disarm the Pattern name up to display Zoom Off lt Zoom gt On Off To display the zoom Orientation Off lt Orientation gt On Off To display the rotation degree Alarm Name Off lt Alarm Name gt On Off To display current Zone Name Mask On lt Zone Name Mask gt On Off To display the zone name mask crossing by camera Back Preset Name On C Boot up Screen Here is possible to display starting the Dome information Protocol Pelco PD Protocol Display protocol in use fil to DIP Switch 1 Comm 4800 N 8 1 Comm Display the communication parameter fil to DIP Switch 1 Address 001 address Display assigning address of Speed Dome fil to DIP Switch 2 Model LCTSD318 Model Display the model in use of three available LCTSD318 LCTSD326 LCTSD336 Version 1 01 lt Version gt firmware version Call the Preset 1 to back Call Preset 1 to back www hrcctv com User Manual Ler y n LCTSD318 326 336 Go D Password In this menu is possible to bump up the security level if the password is enable Input PW gt For input the password the next sub menu display Old PW eee purer We COn P Wo PW Protection On Back Back Before to change input the old password lf old password is correct cursor goes back
19. pening inside the product Slots and openings are provided for ventilation and should never be covered Do not place under direct sunlight or heat sources INFORMAZIONI SULL AMBIENTE ENVIRONMENT INFORMATION Note per lo smaltimento del prodotto i valide per la Comunit Europea Questo prodotto e stato progettato e XI assemblato con materiali e componenti De di alta qualita che possono essere riciclati e riutilizzati Non smaltire il prodotto come rifiuto solido urbano ma EE smaltirlo negli appositi centri di raccolta E possibile smaltire il prodotto direttamente dal distributore dietro l acquisto di uno nuovo equivalente a quello da smaltire Abbandonando il prodotto nell ambiente si potrebbero creare gravi danni all ambiente stesso Nel caso il prodotto contenga delle batterie e necessario rimuoverle prima di procedere allo smaltimento Queste ultime debbono essere smaltite separatamente in altri contenitori in quanto contenenti sostanze altamente tossiche Il simbolo rappresentato in figura rappresenta il bidone dei rifiuti urbani ed tassativamente vietato riporre l apparecchio in questi contenitori L immissione sul mercato dopo il 1 luglio 2006 di prodotti non conformi al DLgs 151 del 25 07 05 Direttiva RoHS RAEE amministrativamente sanzionato Disposal of waste products for European Union This products was designed to minimize their impact on the environment by reducing or eliminating hazardou
20. re elevated show to light so CCD charget the image always come out of more brightness Time of show will be smaller and image come out of more darkness Select one of the next option x1 x2 x4 x8 x15 x30 x60 Default x80 x90 x 100 X125 x180 x250 x350 x500 x725 x1000 x1500 x2000 x3000 x4000 x6000 x 10000 Freeze Mode Arm On or disarm Off Freeze function for image freeze White Balance Select modality between the next option Auto Select this option automatically carry out Inside Use this option for inside application lt Outside gt Use this option for outside application ATW Auto Tracking White Function automated of middle white balance WB R 000 WB B 000 Back OPW Do not use Manual Select Manual the video displays sub menu to adjust color red and blue manually www hrcctv com User Manual Ler Ga LCTSD318 326 336 Go BLC Mode Select this option to access in sub menu and arm lt On gt or disarm lt Off gt the function BLC Mode On Back 3 7 PAN TILT setup Auto Stop Time Speed Amplify Proportional P T Set North System Lens Camera Pan Tilt Back Auto Running Privacy Mask Alarm Back FEE Auto Stop Time The function and select some particular protocol Dome will not stop moving even there is no operation on joystick In this menu is possible arm disarm the seconds that dome will stop moving without receiving any commands Note Do no
21. s materials and designing for recyclables This product should be handed over to a designated collection point e g on an authorized one for one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment Improper handling of this kind of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances This symbol indicates that this product has not to be disposed of with your household waste according to the WEEE Directive For more information about where you can drop off your waste equipment for recycling please contact your local city waste authority or your household waste disposal service GARANZIA Warranty Questa garanzia ha validit di 2 anni a partire dalla data di acquisto assicurata solo dietro presentazione della fattura o scontrino rilasciati al cliente dal rivenditore L assistenza gratuita non e prevista per i guasti causati da Uso improprio 061 prodotto immagazzinamento inadeguato cadute o urti usura sporcizia acqua sabbia manomissione da personale non autorizzato del prodotto rispetto a quanto previsto nei manuali d uso inclusi Riparazioni modifiche o pulizia effettuate da centri assistenza non autorizzati da HR EUROPE Danni o incidenti le cui cause non possono essere attribuite alla HR EUROPE comprendenti e non limitati a fulmini eventi naturali alimentazione e venti
22. set e Tour Setup Remove and test 4 Tour e Cruise Select speed and restrict 4 Cruise e Pattern Record Test and bootup 4 Pattern e Zona Zone name identification and passage speed e Park time 1 255 Off e Park action Preset Pattern 1 4 Cruise 1 4 Tour 1 4 Aree privacy setup pag 18 e Mask Number 1 8 e Mask Setup Select zone to mask e Remove Mask Remove current mask e Remove All Remove all mask Alarm setup pag 19 e Alarm Input 1 8 Preset Pattern 1 4 Cruise 1 4 Tour 1 4 e Alarm1 Output e Arm Disarm Arm Disarm e Interval lt s gt 1 255 www hrcctv com 1 pas User Manual B LCTSD318 326 336 3 4 System Setup System Site Info Lens Display Setup Camera Boot up Screen Pan Tilt Password Auto Running Default Privacy Mask System Reboot Alarm Back Exit Site Info The menu permits to use have Dome information Address 001 lt address gt The parameter is not changeable and display that address is be assigned to the Name Dome 1 Speed Dome by DIP Switch pag 8 Broadcast ID 255 lt Name gt Assigning name to a dome helps user to remember which dome it is Back lt Broadcast ID gt Each other want to assigne software address to the Speed Dome Setup here the desired value Display Setup Here is possible to select information need to display in over printing Dome Name Off lt Dome Name gt On Off To display the camera name lt Preset Name gt O
23. t put in the function with protocol Pelco PD 5 Speed Amplify The speed of Dome is mush lower with some protocols control In this menu is possible set speed amplify to accelerate domes Select one parameter between x1 and x32 Note Do not put in the function with protocol Pelco PD Proportional P T Arm On and disarm Off function for proportional movement while zooming in If is up this function decreases pan and tilt movement while zooming in D Set North Be better to set geographic north 3 8 Auto running setup System Lens Camera Pan Tilt Preset Tour Cruise Pattern Zone Auto Running Privacy Mask Lesina Alarm Park Action Back Back 0000 288 16 www hrcctv com User Manual 1 or LCTSD318 326 336 Preset Preset No Name Current Setup Test gt Preset Tour Cruise Pattern Next Test Remove current Back Zone Park Time Park Time Back Select lt Preset gt to enter sub menu and control Preset lt Preset Number gt Select preset number to be make on or adjustment lt Name gt Put preset name to show lt Current Setup gt Save Preset lt Test gt The current preset test lt Next Test gt The next preset test lt Remove current gt Select to delete the current preset Tour Preset Tour Cruise Pattern Zone Park Time Park Action Back Tour No Interval Edit Test Run Back Select lt Tour gt To enter sub menu and make on or a
24. tory default settings Language e System Reboot Reboot Dome system Back e Language select the language 3 3 Menu explanation Site Info Display setup The main menu is subdivide in 7 sub menu Zoom Speed Digital Zoom Joystick AF AI Lens setup pag 14 e Zoom Speed high low e Digital Zoom On Off r e Joystick AF Al AF AI Iris Focus Off di AFtime Autofocus 0 255 Off Day Night e Al timeAutolris 0 255 Off y e ALC 0 31 Lens Back Ni e Day Night Auto Off Camera Pan Tilt Sensibility Auto Running Freeze Mode Privacy Mask White Balance Alarm BLC Mode Exit Back Camera setup pag 15 e Sensibility x1 x10000 e Freeze Mode On Off e White Balance Auto inside outside OPW ATW manual e BLC Mode Level On Off Auto Stop Time Speed Amplify Proportional P T Set Nord Note Back Pan Tilt setup pag 16 e Auto Stop Time 1 255 Off e Speed Amplify 1 32 Off e Proportional P T On Off e Set Nord Set Nord e OSD menu will close automatically after 1 Preset Auto running setup pag 15 minute without any operation pag 12 Tour Cruise Pattern Zone Park Time Park Action Back Mask Number 2026 Remove Mask Remove All Mask Back Alarm In 1 Alarm In 2 Alarm In 3 Alarm In 4 Alarm In 5 Alarm In 6 Alarm In 7 Alarm In 8 Exit 1 Arm Disarm Interval lt s gt Back e Preset Save Remove Rename Pre
Download Pdf Manuals
Related Search