Instruction Manual
Contents
1. Winco Mig LLC warrants this product to be free of manufacturers defects in maternal and workmanship provided that the product is used according to normal operating conditions and proper maintenance intended by manufacturer This warranty is available only to the onginal retail purchaser is non transferable and commences on the date of retail sale proof of purchase required Limited One Year Complete Product Warranty Winco Mfg LLG warrants the complete product for one 1 year At Winco Mfg LLC sole discretion it may repair or replace any components freight free that are found to be defective during the first year Winco Mra LLC shall not be liable for any Jabor_or any other costs incurred as a result of or in conjunction with a warranty claim Limited Three Year Warranty Winco Mfg LLC warrants the recliner mechanisms electrical components vinyl from cracking or delaminating pressurized gas springs when new for a period of three 3 years At Winco Mfg LLC sole discretion it may repair or replace components on to be defective Winco Mfg LLC shall not be liable for any labor Limited Lifetime Chair Frame Warranty Winco Mfg LLC warrants the steel chair frame when new for the lifetime of the orginal purchaser This limited warranty does not apply to paint finish or any components attached to the frame such as upholstery foam casters mechanisms or related parts that are covered under above warrant2. the bottom FIG 4A 8 Place the arm bracket on top of the IV Bracket and re install the 2 bolts using a 2 wrench FIG 4 9 Re install the upholstered arm onto the chair frame FIG 5 10 Your chair should look like FIG 6 FIG 4 FIG 4A 006312 Revision F Date 10 22 13 JWC elV Pole Attachment Models 5400 5570 5580 5670 6700 6710 e Parts Included Description IV Bracket Assembly 14 20 Nylon Lock nut installed 3 7 Phillipos head Screw installed IV Pole TR e Tools needed Phillips Head Screwdriver Powered tools NOT recommended e Assembly Instructions 1 Locate the rear side of the chair and remove the 2 screws from the rear brace FIG 1 NOTE Left amp Right is determined as if sitting in the chair 2 Next line up the holes in the IV bracket with the holes in the rear brace FIG 2 Nut and bolt pre installed on the IV tube should be in down position FIG 2 ARROW 3 Secure the bracket to the chair frame using the 2 screws previously removed in step 1 FIG 3 5 Insert the IV Pole Your chair should look like that of FIG 4 when assembly is complete D 006312 Revision F Date 10 22 13 Page 7 of 8 Part Number 227630 LEFT or RIGHT 566204 566504 480500 JWC Page 8 of 8 5516 SW 1 Lane Ocala A 34474 lt Phone 352 854 2929 800 237 3377 Fax 352 LIMITED WARRANTY 854 9544 TERMS
3. Page 1 of 8 IV IV Pole Attachment For Models 2570 2571 2572 2573 2574 2575 5251 5261 5271 5281 5291 53517 5361 5400 5560 5570 5580 5670 5680 5851 5861 6530 6531 6540 STO STR 6541 6550 6551 6560 6570 6571 6700 6710 6740 6750 6940 CU MER INSTRUC TONS 6950 6980 6990 PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT If you have trouble understanding these instructions contact your dealer or Winco customer support 800 237 3377 before attempting to use this product otherwise injury may occur TO REDUCE THE RISK OF INJURY TO PERSONS READ AND FOLLOW ALL DIRECTIONS DO NOT use the IV pole for pulling moving or holding the chair in place DO NOT use this attachment in any location or on products other than those listed in these instructions DO NOT make any modifications to the bracket or pole IV Pole and included bracket are designed for hanging IV solutions ONLY Immediately remove from service Any chair with mechanical or visible damage USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS SAVE THESE INSTRUCTIONS for future reference and training 5516 Southwest 1 Lane Ocala FL 34474 1 800 237 3377 352 854 2929 Fax 352 854 9544 e mail customerservice wincomfg com Visit us on the web www wincomfg com PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY 006312 Revision F Date 10 22 13 JWC Page 2 of 8 elV Po
4. as if sitting in the chair 4 Place the IV Bracket over the cross brace reinsert the screws and tighten to a snug fit FIG 3 5 Your chair should look like FIG 4 006312 Revision F Date 10 22 13 Page 5 of 8 Part Number 227610 227610B 566204 566504 480500 227610 Left Bracket Right Bracket JWC Page 6 of 8 e Assembly Instructions 5680 6740 6750 6940 6950 amp 6980 6990 Left Side Only 1 First check the bracket that came with your IV Pole Attachment Kit Verify that the screw and lock nut already installed are in their proper location FIG 1 2 Locate the left or right rear side for 6940 6950 Locate the left rear side for 6980 6990 VOTE Left amp Right is determined as if sitting 227610 227610 Left Bracket Right Bracket in the chair 3 CAREFULLY place the chair on it s side amp And open the swing arm all the way FIG 2 4 Using a 12 wrench amp a 3 16 allen wrench unscrew the swing arm hinge bolt FIG 3 Some FORCE may need to be applied to the allen wrench in order to loosen the hinge bolt 5 Take the loosened bolt out of the arm bracket lift upholstered swing arm off of frame and place on floor 6 Use a 1 2 wrench and REMOVE the bolts from the hinge bracket FIG 4 7 Line up the IV Bracket with the holes in the upholstered arm Be sure the pre installed screw and nut on the IV Bracket is towards
5. ed e Assembly Instructions 1 006312 Locate the proper location on the chair for the IV U Bracket Assembly FIG 1 amp 1A Left amp Right is determined as if sitting in the chair Insert the IV Spacer into the IV U Bracket FIG 2 or FIG 2A and place onto chair frame 527 IV Spacer should the top of the IV U bracket Insert the two screws through the holes in the IV U Bracket FIG 2B Screw on the nylon lock nuts and using the wrench provided tighten the lock nuts to the bracket FIG 3 Your chair should look similar to that of FIG 4 FIG 4 be placed towards B PO WDND Revision F Date 10 22 13 Page 3 of 8 Part Number 227600 LEFT 227605 RIGHT 227607 700700 566204 966504 566571 480500 JWC Page 4 of 8 elV Pole Attachment Models 2570 2571 2572 2573 2574 2575 e Parts Included Description Qty Part Number IV U Bracket Assembly 1 227600 RIGHT 227605 LEFT IV Spacer 1 227607 1 Grey Cap 2 700700 14 20 Nylon Lock nut 1 installed 3 566204 3 Phillips head Screw installed 1 566504 23 4 Phillips head Screw 2 566571 IV Pole 1 480500 e Tools needed e Assembly Instructions 6 006312 Your chair should look similar to that of FIG 4 Tyo Phillips Head Screwdriver 7 16 wrench multiple size wrench included Powered tools NOT recommended Locate the
6. ies Winco Mig LLC shall not be liable for any labor shi ing or any other costs incurred as a result The purchaser s exclusive rained under this warranty shall be limited to such repair or replacement of defective components at Winco Mfg LLC sole discretion For warranty service contact the dealer that the product was originally purchased from or Winco Mfg LLC directly EACLUSIONS There are no other warranties conditions representations or guarantees express or implied made or intended by Winco Mfg LLC and all other warranties conditions representations or guarantees including any warranties conditions representations or guarantees under any Sale of Good Act or Like legislation or statute is hereby expressly excluded Any and all other implied warranties shall not extend beyond the duration of the express warranty Liability for incidental or consequential damages is excluded to the extent permitted by law Some states do not allow the exclusion or limitation so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights In addition you may also have other rights which vary from state to state GENERAL PROVISIONS No warranty herein contained or set out shall apply when damage or repair is caused by any of the following 1 Damage in transit 2 Accident alteration abuse or misuse of product ie exceeding weight capacities applying inordinate pressure to footrest leg rest use in Men
7. le Attachment Models 5251 5261 5291 5351 5361 5851 5861 6530 6531 6540 6541 6570 6571 e Parts Included Description Qty Part Number IV U Bracket Assembly 1 227600 LEFT 227605 RIGHT 14 20 Nylon Lock nut 1 installed 3 566204 3 4 Phillipos head Screw installed 1 566504 23 4 Phillips head Screw 2 566571 IV Pole 1 480500 e Tools needed Phillips Head Screwdriver 7 16 wrench multiple size wrench included Powered tools NOT recommended Pictures shown with 227600A OPTION e Assembly Instructions 1 Locate the rear side of the chair and place the IV U Bracket Assembly onto the rear chair frame rail FIG 1 NOTE Left amp Right is determined as if sitting in the chair 2 Next insert the 2 234 screws into the holes provided on the bracket assembly FIG 2 3 Secure the bracket to the chair frame using the 2 nylon lock nuts Tighten using the wrench provided FIG 3 4 Insert the IV Pole Your chair should look like that of FIG 4 when assembly is complete 006312 Revision F Date 10 22 13 JWC elV Pole Attachment Models 5271 5281 6550 6551 e Parts Included Description IV U Bracket Assembly IV Spacer 1 Grey Cap 14 20 Nylon Lock nut 7 installed 3 Phillips head Screw installed 23 4 Phillips head Screw IV Pole e Tools needed Phillips Head Screwdriver 7 16 wrench multiple size wrench included Powered tools NOT recommend
8. proper location on the chair for the IV U Bracket Assembly FIG 1 NOTE Left amp Right is determined as if sitting in the chair Insert the IV Spacer into the IV U Bracket FIG 2 and place onto chair frame Insert the two screws through the holes in the IV U Bracket FIG 3 Screw on the nylon lock nuts and using the wrench provided tighten the lock nuts to the bracket FIG 3 Revision F Date 10 22 13 JWC elV Pole Attachment Models 5560 5680 6560 6740 6750 6940 6950 6980 6990 e Parts Included Description IV Bracket Assembly 5560 6560 6940 6950 IV Bracket Assembly 6980 6990 14 20 Nylon Lock nut installed 3 4 Phillipos head Screw installed IV Pole i b h h Q Paa a e Tools needed Phillips Head Screwdriver 5560 6560 ONLY VY Wrench 6940 6950 6980 6990 ONLY 3 16 Allen Wrench 6940 6950 6980 6990 ONLY Powered tools NOT recommended e Assembly Instructions 5560 6560 amp 6980 6990 Right Side ONLY 6940 6950 amp 6980 6990 Left Side ONLY instructions on next page 1 First check the bracket that came with your IV Pole Attachment Kit Verify that the screw and lock nut already installed are in their proper location FIG 1 2 Locate the left or right rear side for 5560 6560 Locate the right rear side for 6980 6990 FIG 2 3 Unscrew the bolts in the cross brace FIG 2A NOTE Left amp Right is determined
9. tal Health facilities or like institutions peas 3 Fire water damage theft war riot hostility acts of God Examples contained in ts list are not to be construed as all inclusive 006312 Revision F Date 10 22 13 JWC
Download Pdf Manuals
Related Search