Home

SBC8163 Series User`s Manual

1. Security Option This allows you to limit access to the System and Setup The default value is Setup When set to System the system prompts for the User Password every boot up Selecting Setup always boots up and prompts for Supervisor Password only when Setup utility is called up PS 2 mouse function control This item allows you to determine to enable the hardware PS 2 mouse function or not The available choices are Enabled and Disabled 36 Award BIOS Ulility SBC8163 Socket370 All in One CPU Card Series User s Manual e PCI VGA Palette Snoop Some non standard VGA display cards may not show colors properly This field allows you to set whether MPEG ISA VESA VGA Cards can work with PCI VGA or not When enabled a PCI VGA can work with a MPEG ISA VESA VGA card When disabled a PCI VGA cannot work with a MPEG ISA VESA Card OS Select for DRAM gt 64MB This allows system to access more than 64MB of DRAM memory when used with OS 2 depends on certain BIOS calls to access memory The default setting is Non OS 2 e Report No FDD For WIN 95 This option allows Windows 95 to share IRQ6 assigned to a floppy disk drive with other peripherals in case the drive is not existing The default setting is No e Video BI OS Shadow This item allows you to change the Video BIOS location from ROM to RAM Video Shadow will increase the video speed e C8000 CBFFF Shadow DCOOO DFFFF Shadow Shadowing ROM reduces available memory betwe
2. SBC8163 Socket370 All in One CPU Card Series User s Manual Extemal LAN Card Wake CN19 On LAN Connector 10 Jumpers and Connectors SBC8163 Socket370 All in One CPU Card Series User s Manual This page does not contain any information SBC8163 Socket370 All in One CPU Card Series User s Manual Chapter 3 Installation This chapter describes the hardware installation procedures on the SBC8163 all in one Socket370 CPU card The following is a list of typical peripherals required to build a minimum system W Powersupply and passive backplane optional E IBM PC AT keyboard W Display monitor m Floppy orhard disk with MS DOS or Flash Disk emulator 3 1 System Memory The SBC8163 industrial CPU card supports one 168 pin DIMM Dual In line Memory Module socket for a maximum total memory of 128MB unbuffer SDRAMs or 256MB buffer SDRAMs The memory module can come in sizes of 16MB 32MB 64MB 128MB and 256MB for buffer type SDRAMs NOTE Use SDRAM modules with PC 100 or PC 133 specification when running 100MHz CPU bus speed With 66M Hz CPU bus speed SDRAM modules with PC66 PC100 or PC133 specification can be used You have to install the Intel Celeron or Pentium Ill processor before installing the memory modules 3 2 CPU Installation Align pin one e g white dot of the CPU with pin one of the socket Pin one of the CPU socket may either be marked on the board orindicated by an arrow head symbol on one comer of the so
3. GND 40 O o t o Power 50 E 8 o gt 0 Y 4 14 USB Connector The Universal Serial Bus USB connector on the SBC8163 is for installation of peripherals supporting the USB interface CN22 is the 10 pin USB connector on the SBC8163 CN22 U S B U U U S S S P B B B o A w G G e 1 1 N N r D D wac wac m0 a aj voc i rn vocc O ezo L O 2020 7 ov ov UZQ Hardware Description 21 SBC8163 Socket370 All in One CPU Card Series User s Manual 4 15 IrDA Connector CN14 is a 10 pin IrDA connector for wireless communication CN14 5V 1 M0 2 nc Reserved 3 Ol L1 4 Reserved Rx 5 O O 6 Reserved GND 7 H DO s NC TX 9 0 L1 10 NC 4 16 ACPI Connector Advanced Configuration and Power Interface ACPI defines a flexible and extensible interface that allows system designers to select appropriate cost feature trade offs for power management The interface enables and supports reliable power management through improved hardware and operating system coordination The specification enables new power management technology to evolve independently in operating systems and hardware while ensuring that they continue to work together CN17 on the SBC8163 is a 6 pin header connector that provides ACPI interface CN17 Hoooooeo 123456 EGPGPS X NWNWB TD D 5 S P O V M N N l 22 Hardware Description SBC8163 Socket370 All in One CPU Card Series User s Manual Chapter 5 Display Drivers 5 1 In
4. Secondary Master Secondary Slave Drive A 1 44M 3 5 in DriveB None Base Memory 640K Extended Memory 15360K Video EGA VGA Other Memory 384K Halt On All Errors Total Memory 16384K ESC Quit v gt Select Item PU PD Modify Fl Help Shift F2 Change Color At the bottom of the menu are the control keys for use on this menu If you need any help in each item field you can press the F1 key It will display the relevant information to help you The memory display at the lower right hand side of the menu is read only It will adjust automatically according to the memory changed The following pages describe each item of this menu Award BIOS Utility 31 SBC8163 Socket370 All in One CPU Card Series User s Manual 32 Date The date format is the day of week from Sun to Sat determined by the BIOS is read only Mont the month Jan 1 through Dec 12 h Date the date from 1 to 31 orthe maximum allowed in the month can key in the numerical function key the year from 1994 to 2079 To set the date highlight the Date field and use the PageUp PageDown or keys to set the current time Time The time format is From 00 to 23 From 00 to 59 From 00 to 59 To set the time highlight the Time field and use the lt PgUp gt lt PgDn gt or keys to set the current time Primary Secondary Master Slave Hard Drives The onboard PCI IDE connectors provide
5. Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices Each channel can support up to two hard disks the first is the Master and the second is the Slave To enter the specifications for a hard disk drive you must select first a Type There are 45 predefined types and 4 user definable types are for Enhanced IDE BIOS Types 1 to 45 are predefined Type User is user definable For the Primary Master Slave as well as Secondary Master Slave you can select Auto under the TYPE and MODE fields This will enable auto detection of your IDE drives and CD ROM drive during POST Press lt PgUp gt lt PgDn gt to select a numbered hard disk type or type the number and press the lt Enter gt key The hard disk will not work properly if you enter incorrect information for this field If your hard disk drive type is not matched or listed you can use Type User to define your own drive type manually If you select Type User the utility will ask you to enter the information on the following table Award BIOS Utility SBC8163 Socket370 All in One CPU Card Series User s Manual CYLS write precompensation landing zone SIZE Automatically adjust according to the configuration MODE Auto for IDE HDD only Normal HD lt 528MB Large for MS DOS only LBA HD gt 528MB and supports Logical Block Addressing NOTE The specifications of your drive must match with the drive table The
6. Strobe CAS The default setting is 3 e SDRAM RAS Precharge Time The precharge time is the number of cycles for the RAS to accumulate its charge before DRAM refreshes If time is insufficient refresh may be incomplete and the DRAM may fail to retain data The default setting is 3 e SDRAM CAS Latency Time When synchronous DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing Do not reset this field from the default value specified by the system designer The default setting is 3 38 Award BIOS Ulility SBC8163 Socket370 All in One CPU Card Series User s Manual DRAM Data Integrity Mode This option sets the data integrity mode of the DRAM installed in the system The default setting is Non ECC System BI OS Cacheable When enabled access to the system BIOS ROM addressed at F0000H FFFFFH is cached provided that the cache controller is disabled Video BI OS Cacheable When enabled access to video BIOS addressed at COOOOH to C7FFFH is cached provided that the cache controller is disabled Video RAM Cacheable Selecting Enabled allows caching of the video BIOS ROM at C0000h to C7FFFh resulting in better video performance However if any program writes to this memory area a memory access error may result 8 Bit I O Recovery Time This option specifies the length of the delay in sysclks inserted between consecutive 8 bit I O operations The settings are 1 2 3 4 5 6 7 or 8 The defaul
7. disabled User Define each of the ranges are from 1 min to 1 hr except for HDD ower Down which ranges from 1 min to 15 min and disable NOTE In orderto enable the CPU overheat protection feature the Power Management field should not be set to Disabled e PM Control by APM When enabled an Advanced Power Management device will be activated to enhance the Max Power Saving mode and stop the CPU internal clock If Advance Power Management APM is installed on your system selecting Yes gives better power savings If the Max Power Saving is not enabled this will be preset to No e Video Off Method This determines the manner in which the monitor is blanked V H SYNC This causes the system to turn off the vertical and horizontal Blank synchronization ports and write blanks to the video buffer Select this option if your monitor supports the Display Power DPMS Management Signaling DPMS standard of the Video Electronics Standards to select video power management values Blank Screen This option only writes blanks to the video buffer e Video Off After When enabled this feature allows the VGA adapter to operate in a power saving mode AlwaysOn Monitor will remain on during power saving modes Suspend gt Off ind blanked when the system enters the Suspend Monitor blanked when the system enters either sp Stby gt Off Susp Stby Suspend or Standby modes All Modes gt Off Monitor blanked when the system
8. enters any power saving mode 42 Award BIOS Utility SBC8163 Socket370 All in One CPU Card Series User s Manual e Modem Use IRQ This field names the interrupt request IRQ line assigned to the modem if any on your system Activity on the selected IRQ always awakens the system The available choices are 3 4 5 7 9 10 11 and NA By default the IRQ is set to 3 8 6 1 PM Timers The following four modes are Green PC power saving functions that are only user configurable when User Defined Power Management is selected See above for available selections e Doze Mode When enabled and after the set time of system inactivity the CPU clock runs at a slower speed while all other devices operate at full speed e Standby Mode After the set period of system inactivity expires the fixed disk drive and the video shut OFF while all other devices operate at full speed e Suspend Mode When enabled and after the set time of system inactivity all devices except the CPU will be shut OFF e HDD Power Down When enabled and after the set time of system inactivity the hard disk drive is powered down while all other devices remain active e Throttle Duty Cycle When system enters Doze mode the CPU clock runs only part of the time You may select the percent of time that the clock runs 8 6 2 PM Events PM events are I O events whose occurrence can prevent the system from entering a power saving mode or can awaken the system fro
9. hard disk will not work properly if you enter incorrect information in these fields If your hard disk drive type is not matched or listed you can use Type Userto define your own drive type manually e Drive A Drive B These fields identify the types of floppy disk drive A or drive B that has been installed in the computer The available specifications are e Video This field selects the type of video display card installed in your system You can choose the following video display cards EGA VG Enhanced Graphics Adapter Video Graphics Array For EGA A VGA SEGA SVGA or PGA monitor adapters default Color Graphics Adapter power up in 40 column mode Color Graphics Adapter power up in 80 column mode For Hercules or MDS adapters includes high resolution monochrome adapters Award BIOS Utility 33 SBC8163 Socket370 All in One CPU Card Series User s Manual Halt On This field determines whether the system will halt if an error is detected during power up No embrs The system boot will halt on any error detected default Allerr rs Whenever the BIOS detects a non fatal error the system will stop and you will be prompted All But Keyboard The system boot will not stop for a keyboard error it will stop for all other errors All But Diskette The system boot will not stop for a disk error it will stop for all other errors All But Disk Key The system boot will not stop for a keyboard or disk error it wi
10. utility When you turn ON the computer the Award BIOS is immediately activated Pressing the Del key immediately allows you to enter the Setup utility If you are a little bit late pressing the Del key POST Power On Self Test will continue with its test routines thus preventing you from invoking the Setup If you still wish to enter Setup restart the system by pressing the Reset button or simultaneously pressing the Ctrl Alt and Delete keys You can also restart by turning the system OFF and back ON again The following message will appear on the screen Press DEL to Enter Setup In general you press the arrow keys to highlight items Enter to select the lt PgUp gt and lt PgDn gt keys to change entries F1 for help and lt Esc gt to quit Award BIOS Utility 29 SBC8163 Socket370 All in One CPU Card Series User s Manual When you enter the Setup utility the Main Menu screen will appear on the screen The Main Menu allows you to select from various setup functions and exit choices ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURATION SAVE amp EXIT SETUP LOAD BIOS DEFAULTS EXIT WITHOUT SAVING LOAD SETUP DEFAULTS Esc Quit V 2 Select Item F10 Save Exit Setup Shift F2 Change C
11. 0 All in One CPU Card Series User s Manual e Swap Floppy Drive This allows you to determine whether to enable Swap Floppy Drive or not When enabled the BIOS swaps floppy drive assignments so that Drive A becomes Drive B and Drive B becomes Drive A By default this field is set to Disabled e Boot Up Floppy Seek When enabled the BIOS seeks for number of track 40 or 80 of the installed floppy drive 360K type has 40 tracks while 760K 1 2M and 1 44M have 80 tracks By default this field is set to Enabled Boot Up NumLock Status This activates the NumLock function after powering up the system By default the system boots up with NumLock ON Gate A20 Option This you to select how Gate A20 is worked Gate A20 is a device used to address memory above 1 MB The default setting is Fast Typematic Rate Setting When disabled continually holding down any key on your keyboard will generate only one instance When enabled you can set the two typematic controls listed next By default this field is set to Disabled Typematic Rate Chars Sec When the typematic rate is enabled the system registers repeated keystrokes speeds You can select speed range from 6 to 30 characters per second By default this item is set to 6 Typematic Delay Msec When typematic rate is enabled this item allows you to set the time interval between the display of the first and second characters By default this item is set to 250msec
12. 335 L mm NOTE Specifications are subject to change without notice 1 3 Utilities Supported SCSI Utility and Drivers SCSI functions only Ethernet Utility and Drivers CRT Drivers System Doctor Introduction 3 SBC8163 Socket370 All in One CPU Card Series User s Manual 1 4 Board Dimensions s ipsps e e 8 q liar i Ha A y c te 4 ES 2l eu SE tz A o o lt N e a ceo eo e e C vv AA 5 ow bd L AR 19 e NT S 33 2 ERA AA Y AA rn ojo o IN wT Y e e e 05 86 4 os 6L e FARA gt 4 Introduction SBC8163 Socket370 All in One CPU Card Series User s Manual Chapter2 Jumpers and Connectors 2 1 Board Layout CN24 Boot JA P D T CN21 PPGA370 Jumpers and Connectors 5 SBC8163 Socket370 All in One CPU Card Series User s Manual 2 2 Jumper Settings Making the proper jumper settings configures the SBC8163 to match the needs of your application The following summary table lists all onboard jumpers and their corresponding functions and or default settings Jes ope eat A JP11 Power Supply Type AT Power Supply rS 4 5 T JP12 DiskOnChip Memory Segment DC000 DFFFF Short 7 8 JP13 JP14 Watchdog Trigger Mode Disabled JP15 JP16 Int Keyboard Power Select System Power Short 1 2 2 2 1 Internal Keyboard Connector Power Sele
13. 7 2 2 7 COM2 RS232 422 485 Settings J P1 J P2 J P3 8 2 3 COMME CEOES nasais duca dioe cie newts CRT SS 9 Chapter 3 Installation dd System MeMO ysamen eei 11 3 2 CPU Installationen taa dita bes is 11 3 3 Completing installati ceicessno io terra 12 Chapter 4 Hardware Description EL Microprocessors aieo iia 13 AZ BIO Sa aa das ds aaa 13 5 3 O Port Address M BD sissricasci na sais bicorid 14 4 4 Interrupt Controller assesseer 15 4 5 General Output Connector 16 4 6 Enhanced IDE Interface Connector 17 4 7 VGA Interface nara 18 4 7 1 CRT Interface Controller 18 4 7 2 Fe atiis vara 18 4 7 3 VGA Connector CNIB 4 o ea ici 18 4 8 Ethernet Connector eeesssssesenne 19 AO SCSI CODneCctOTF ioc sisi ponen isos 19 4 10 Floppy Disk Controller cinc 19 4 11 Parallel Port Interface sesesesssennnnn 20 4 12 Serial Port Interface sess 20 Table of Contents V vi 4 12 1 Serial Ports IRQ Selection Table of Contents 4 13 Keyboard and PS 2 Mouse Connectors 21 4 14 USB CONNECT aiii 2l 4 15 IrDA COMEM rta er re 22 4 16 ALGPIT ODDOCIUDE acdossipelasbbianr ir 22 Chapter 5 Display Drivers S L ING Asconaansads etes box i in ena iza Gras assado 23 e EMI nisu c I ac da 23 2 9 Drivers SUDDOFUDU sessicnatososiaciosdrcrosiniatas 24 Chapter 6 Ethernet 6 1 go e NE ont o dj RR PR RR ni 25 Due PISS asteca pisndasochs is a 25 6 3 Drivers SU
14. ARD SOFTWARE INC DE HDD Block Mode Enabled Onboard Serial Port 1 3F8 IRQ4 DE Primary Master PIO Au Onboard Serial Port 2 2F8 IRQ3 DE Primary Slave PIO Au UART Mode Select Normal DE Secondary Master PIO Au DE Secondary Slave PIO Au DE Primary Master UDMA Au IR Transmission delay Enabled DE Primary Slave UDMA Au Onboard Parallel Port 378 IRQ7 DE Secondary Master UDMA Au Parallel Port Mode SPP DE Secondary Slave UDMA Au ECP Mode Use DMA r3 On Chip Primary PCI IDE Enabled EPP Mode Select EPP1 7 On Chip Secondary PCI IDE Enabled USB Keyboard Support Disabled nit Display First PCI Slot POWER ON Function BUTTON ONLY ESC Quit V 2 Select Item KBC input clock 8 MHz F1 Help PU PD Modify Onboard FDC Controller Enabled F5 Old Values Shift F2 Color F6 Load BIOS Defaults F7 Load Setup Defaults e IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive e IDE Primary Secondary Master Slave PIO The four IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the four IDE devices that the onboard IDE interface supports Modes O through 4 provide successively increased performance In Auto mode the system automatically determines the best mode for each device The options available are Auto Mode 0 Mode 1 Mode 2 Mode 3 and Mode 4 Award BIOS Utility 49 SB
15. C8163 Socket370 All in One CPU Card Series User s Manual IDE Primary Secondary Master Slave UDMA Ultra DMA 66 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If your hard drive and your system software both support Ultra DMA 33 66 select Auto to enable BIOS support The options available are Auto Mode 0 Mode 1 and Mode 2 On Chip Primary Secondary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels Select Enabled to activate each channel separately USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus USB controller and you have a USB keyboard The options available are Enabled Disabled e Init Display First This item allows you to decide to active whether PCI Slot or AGP first The options available are PCI Slot AGP e POWER ON Function This option allows users to select the type of power ON sequence for the system to follow The default value is Button Only Follows the conventional way of turning OFF system power via power button Upon selecting this option the KB POWER ON Password line appears Press Enter and you ll be prompted to enter and Password confirm a password of your choice After setting the password succeeding attempts to power ON the system will result to null For system to a
16. Hardware Description SBC8163 Socket370 All in One CPU Card Series User s Manual 4 4 Interrupt Controller The SBC8163 is a fully PC compatible control board It consists of 16 ISA interrupt request lines and 4 of the 16 can be either ISA or PCI The mapping list of the 16 interrupt request lines is shown below wr Foriycheckemor IRQO Systemtimeroutput Serial port 2 1RQ6 Floppy disk controller IRQ9 Reserved SCS Math coprocessor NOTE The table above displays the standard mapping list of the interrupt controller fpr reference The displayed mapping list varies for SBC8163V SBC 8163VE and SBC8163VES board Hardware Description 15 SBC8163 Socket370 All in One CPU Card Series User s Manual 4 5 General Output Connector CN11 2 4 6 8 10 12 14 16 18 20 Oxo oo Orono DIO O Y o 1 3 5 7 9 1113 15 17 19 Power LED This 3 pin connector designated at Pins 1 3 and 5 of CN11 connects the system power LED indicator to its respective switch on the case Pin 1 is and pin 5 is assigned as The Power LED lights up when the system is powered ON Keyboard Lock Pins 7 and 9 of CN11 connect to the case s keyboard lock connector When connecting the keyboard lock connector onto CN11 pin 7 is designated as positive pole and pin 9 as the negative pole External Speaker and Internal Buzzer Connector Pins 2 4 6 and 8 of CN11 connect to the case mounted speaker unit or internal buzze
17. NS susana dad adest das od ptos osea err 61 CPU Fan Connector GNO vuota aida aia 61 WAKE ON LAN Connector CNA naniii 61 Table of Contents This page does not contain any information viii SBC8163 Socket370 All in One CPU Card Series User s Manual Chapter 1 Introduction 1 1 General Description The SBC8163 CPU card is an industrial grade CPU card incorporating the Intel 440BX AGPset chipset and the ATI Rage XL AGP 2X VGA controller both ensuring its compatibility with PCI bus passive backplanes Its 6 layer structure reduces signal noise and built in power management feature These advanced concepts along with the PCI Local Bus architecture bring outstanding performance to Windows based applications Designed for the professional embedded developers the Socket370 all in one SBC8163 CPU card is virtually your ultimate one step solution to various applications Introduction 1 SBC8163 Socket370 All in One CPU Card Series User s Manual 2 Specifications Chipset Intel 440BX AGPset CPU Socket Socket370 Bus Clock 66 100 MHz CPU Intel Socket370 Celeron Pentium III up to 800MHz L2 Cache Integrated in CPU BIOS Award 2MB PnP Flash BIOS System Memory E 3x 168 pin DIMM sockets E Maximum buffered SDRAM 256MB or unbuffered SDRAM 128MB up to 768MB SDRAM m ECC parity checking e e o o o o e IDE Interface 2 bus mastering EIDE up to four devices Ultra DMA 33 supported e FDD Interface Supports up to 2 dr
18. SBC8163 Socket370 Full size All in One CPU Card Series User s Manual Disclaimers The information in this manual has been carefully checked and is believed to be accurate AXIOMTEK Co Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use AXIOMTEK assumes no responsibility for any inaccuracies that may be contained in this document AXIOMTEK makes no commitment to update or to keep current the information contained in this manual AXIOMTEK reserves the right to make improvements to this document and or product at any time and without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of AXIOMTEK Co Ltd Copyright 2000 by AXIOMTEK Co Ltd All rights reserved November 2000 Version A3 Printed in Taiwan ESD Precautions Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the following precautions W Do not remove boards or integrated circuits from their anti static packaging until you are ready to install them W Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This helps to discharge any static electricity on your b
19. TURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURA ETUP f CONFIGU Load BIOS Defaults Y N N y LOAD BIOS DEFAULT SAVING LOAD SETUP DEFAULTS Esc Quit v gt Select Item F10 Save Exit Setup Shift F2 Change Color Load BIOS Defaults except Standard CMOS Setup To load BIOS defaults value to CMOS SRAM enter Y If not enter N Award BIOS Utility 47 SBC8163 Socket370 All in One CPU Card Series User s Manual 8 9 Load Setup Defaults This option allows you to load the default values to your system configuration These default settings are optimal and enable all high performance features ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURA ETUP f eo E Load SETUP Defaults Y N N LOAD BIOS DEFAULT SAVING LOAD SETUP DEFAULTS Esc Quit V gt Select Item F10 Save Exit Setup Shift F2 Change Color Load BIOS Defaults except Standard CMOS Setup To load SETUP defaults value to CMOS SRAM enter Y If not enter N 48 Award BIOS Utility SBC8163 Socket370 All in One CPU Card Series User s Manual 8 10 Integrated Peripherals This option sets your hard disk configuration mode and port ROM PCI ISA BIOS INTEGRATED PERIPHERALS AW
20. YLS HEAD PRECOMP LANDZ SECTOR MODE 1 Y 0 0 0 0 0 0 0 NORMAL NOTE Some OSes like SCO UNIX must use NORMAL for installation Up to four IDE drives can be detected with parameters for each appearing in sequence inside a box To accept the displayed entries press the Y key to skip to the next drive press the N key If you accept the values the parameters will appear listed beside the drive letter on the screen Award BIOS Utility 53 SBC8163 Socket370 All in One CPU Card Series User s Manual 8 13 Save amp Exit Setup This allows you to determine whether or not to accept the modifications Typing Y quits the setup utility and saves all changes into the CMOS memory Typing N brigs you back to Setup utility ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURA ETUP Mob ang SAVE to CMOS and EXIT Y N N j LOAD BIOS DEFAULT SAVING LOAD SETUP DEFAULTS Esc Quit V gt Select Item F10 Save Exit Setup Shift F2 Change Color Saves all Data amp Exit Setup 54 Award BIOS Ulility SBC8163 Socket370 All in One CPU Card Series User s Manual 8 14 Exit Without Saving Select this option to exit the Setup utility without saving the changes you have made in this session Typing Y will quit
21. anced IDE controller that can support master slave mode and post write transaction mechanisms with 64 byte buffer and master data transaction This feature connected via connector CN5 and CN6 allows the SBC8163 to handle 4 IDE drives Refer to Appendix B for the pinout assignments of CN5 and CN6 Hardware Description 17 SBC8163 Socket370 All in One CPU Card Series User s Manual 4 7 VGA Interface 4 7 1 CRT Interface Controller The built in ATI Rage XL is a high performance super VGA display controller with onboard 8M bytes VGA RAM It is capable of driving a wide array of CRT displays It can also support CRT at a maximum resolution of up to 1600x1200 with 16 bit colors 4 7 2 Features e Fully compatible with IBM VGA e CRT monitor can be displayed simultaneously Onboard 8M bytes VGA SDRAM e Supports non interlaced CRT monitors with resolutions up to 1600x1200 16 bit colors e Direct interface to Color and Monochrome Dual Drive and Single Drive panels e SMARTMAP intelligent color to gray scale conversion enhances text legibility e Integrated programmable linear address feature accelerates GUI performance e Hardware Windows acceleration 4 7 3 VGA Connector CN18 The SBC8163 has three connectors that support CRT VGA individually or simultaneously CN18 is a standard 15 pin pin header connector commonly used for the CRT VGA display Configuration of the VGA interface is done via the software utility and no jumper se
22. aults Load Setup Defaults Award BIOS Utility 45 SBC8163 Socket370 All in One CPU Card Series User s Manual 46 PNP OS Installed This item allows you to determine install PnP OS or not The options available are Yes and No Resource controlled by The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices However this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows 95 The options available are Auto and Manual Reset Configuration Data Normally you leave this field Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup or if you have installed a new add on and the system reconfiguration has caused such a serious conflict that the operating system can not boot The options available are Enabled and Disabled Assign I RQ For USB VGA Enable Disable to assign IRQ for USB VGA The options available are Enabled Disabled Award BIOS Ulility SBC8163 Socket370 All in One CPU Card Series User s Manual 8 8 Load BIOS Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM These default settings are non optimal and disable all high performance features ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEA
23. bled Standby Mode Disab Serial Port Enabled Suspend Mode Disab Parallel Port Disabled HDD Power Down Disab Throttle Duty Cycle 62 5 PCI VGA Act Monitor Disabled Soft Off by PWR BTTN Instant Off PowerOn by Ring Enabled Resume by Alarm Disabled Onboard LAN Wakeup Enabled ESC Quit nv gt Select Item F1 Help PU PD Modify PCI LAN Card Wakeup Enabled F5 Old Values Shift F2 Color IRQ 8 Break Suspend Disabled F6 Load BIOS Defaults F7 Load Setup Defaults ACPI Function This item allows you to enable disable the Advanced Configuration and Power Management ACPI The options available are Enabled Disabled e Power Management This category allows you to select the type or degree of power saving and is directly related to the following modes m HDD Power Down m Doze Mode m Suspend Mode There are four selections for Power Management three of which have fixed mode settings Award BIOS Utility 41 SBC8163 Socket370 All in One CPU Card Series User s Manual Disable default No power management Disables all four modes inimum power management Doze Mode 1 hr Standby ode 1 hr Suspend Mode 1 hr and HDD Power Down 15 min Min Power Saving aximum power management ONLY AVAILABLE OR SL CPU S Doze Mode 1 min Standby Mode 1 Max Power Saving F min Suspend Mode 2 1 min and HDD Power Down 1 min A i lows you to set each mode individually When not
24. cket Normally its diagonal comer distinguishes pin one on the socket 2 To complete the CPU installation gently press the CPU into place 3 Double check the insertion and orientation of the CPU before applying power Improper installation will result in permanent damage to the CPU Installation 11 SBC8163 Socket370 All in One CPU Card Series User s Manual 3 3 Completing Installation To complete the installation follow the steps listed below 1 2 3 12 Make sure the power is OFF Set the REM jumpers according to the jumper settings on Chapter 2 Install the SBC8163 CPU card into one of the slots on the passive backplane You may allow the SBC8163 to stand alone asa single board computer Connect the I O cablesand peripherals i e floppy disk hard disk monitor keyboard power supply and etc to the CPU board NOTE The color of pin one is usually red or blue while others are gray Turn ON the system power Installation SBC8163 Socket370 All in One CPU Card Series User s Manual Chapter 4 Hardware Description This chapter gives a detailed explanation of the hardware features onboard the SBC8163 all in one Socket370 CPU card 4 1 Microprocessors The SBC8163 supports Intel Celeron or Pentium Ill CPUs Systems based on these CPUs can be operated under UNIX OS 2 Linux Windows NT 2000 Windows 95 98 and MS DOS environments The system s performance depends on the installed CPU on the board Wh
25. ction JP16 e System Power Short 1 2 default 3 suspend Power Shot23 JP16 6 Jumpers and Connectors SBC8163 Socket370 All in One CPU Card Series User s Manual 2 2 2 VGA Controller Interrupt Control JP4 Open default o ATP S default Short 1 2 4 5 7 8 10 11 lATXP S Short2 3 5 6 8 9 11 12 wo N oon gt o nmurm ood N 2 2 4 Watchdog Trigger Mode Setting JP14 The watchdog timer is an indispensable feature of the SBC8163 It has a sensitive error detection function and a report function When the CPU processing comes to a halt the watchdog either generates a NMI or resets the CPU nmi Short1 2 O 2 2 5 DiskOnChip Memory Segment JP12 ES Short 1 2 Short 3 4 Short 5 6 Short 7 8 default 2 2 6 SCSI Function Interrupt Control JP7 Bg oj o n nis aja Ojo A D Ojo Open default 1 2 Use One Interrupt Jumpers and Connectors 7 SBC8163 Socket370 All in One CPU Card Series User s Manual 2 2 7 COM2 RS232 422 485 Settings JP1 JP2 JP3 Short 3 5 4 6 Short 1 2 7 8 Short 3 5 4 6 Short 1 3 2 4 Short 3 4 Short 1 3 2 4 Short 1 3 2 4 Short 5 6 7 8 Short 1 3 2 4 JP2 JP1 and JP3 imul 2 4 6 000 5 0 0 6 1 3 5 7 OF 8 8 Jumpers and Connectors SBC8163 Socket370 All in One CPU Card Series User s Manual 2 3 Connectors The connectors allow the CPU card to connect with other parts of the system Some problems encoun
26. ctivate user must input the password via keyboard then press Enter This option is very similar with that of Password Hot key Hot KEY combinations range from Ctrl F1 to Ctrl F 12 User may define this combination from the Hot key Power ON option Mouse This allows system to POWER ON by clicking the left mouse Left button To enable user must reboot and allow system to finish booting up otherwise the setting will not take effect This allows system to POWER ON by clicking the right mouse Mouse Right button To enable this setting user must reboot and allow system to finish the boot up process otherwise the setting will not take effect 50 Award BIOS Ulility SBC8163 Socket370 All in One CPU Card Series User s Manual e KBC input clock This item sets the input clock for the keyboard controller The default value is 8 MHz Onboard FDC Controller Select Enabled if your system has a floppy disk controller FDC installed on the system board and you wish to use it If you install and in FDC or the system has no floppy drive select Disabled in this field The options available are Enabled Disabled Onboard Serial Port 1 Port 2 Select an address and corresponding interrupt for the first and second serial ports The options available are 3F8 IRQ4 2bE8 IRQ3 3E8 IRQ4 2F8 IRQ3 Disabled Auto UART Mode Select The second serial port offers these infrared interface modes gt IrDA gt ASKIR IrDA compliant serial infrared
27. d mode IBM PC XT PC AT and papo 1M compatible with bi directional parallel port e Enhanced mode Enhance parallel port EPP compatible with EPP 1 7 and EPP 1 9 IEEE 1284 compliant e High speed mode Microsoft and Hewlett Packard extended capabilities port ECP IEEE 1284 compliant The address select of the onboard parallel port in LPT1 3BCH or disabled is done by BIOS CMOS setup 4 12 Serial Port Interface The serial interface onboard SBC8163 consists of COM1 port CN4 or CN16 supports RS 232 and COM2 CN7 provide RS 232 422 485 connectivity 4 12 1 Serial Ports IRQ Selection SBC8163 uses a 10 pin connector for COM2 CN7 and a DB9 pin connector for COM1 CN16 on non Ethernet CPU cards or a 10 pin for COM1 CN4 with onboard Ethernet CPU card Interrupt Requests on COM1 and COM2 are selected via IRQ4 and IRQ3 respectively Additionally both ports can be enabled or disabled via BIOS setting The RS 232 pin assignments for COM1 and COM2 along with the RS 485 pin assignments for COM2 are in Appendix B 20 Hardware Description SBC8163 Socket370 All in One CPU Card Series User s Manual 4 13 Keyboard and PS 2 Mouse Connectors The SBC8163 provides a keyboard CN23 and PS 2 mouse CN24 interface with a 5 pin connector CN25 is a DIN connector for PS 2 keyboard connection CN25 8 CN23 24 a s D c O S g O2 50 Clock 1 Z p loc o 2855 Data 20 S d A em ee e e No Connection 3 O 5x x 6 9 9
28. e system To specify a password highlight the type you want and press Enter The Enter Password message prompts on the screen Type the password up to eight characters in length and press lt Enter gt The system confirms your password by asking you to type it again After setting a password the screen automatically returns to the main screen To disable a password just press the Enter key when you are prompted to enter the password A message will confirm the password to be disabled Once the password is disabled the system will boot and you can enter Setup freely ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURA ETUP LOAD BIOS DEFAULT SAVING LOAD SETUP DEFAULTS Esc Quit v gt Select Item F10 Save Exit Setup Shift F2 Change Color Change Set Disable Password 52 Award BIOS Ulility SBC8163 Socket370 All in One CPU Card Series User s Manual 8 12 IDE HDD Auto Detection This option detects the parameters of an IDE hard disk drive and automatically enters them into the Standard CMOS Setup screen ROM PCI ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE INC HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master Select Primary Master Option N SKIP N OPTIONS TYPE SIZE C
29. en 640KB and 1024KB These fields determine whether optional ROM is copied to RAM or not Award BIOS Utility 37 SBC8163 Socket370 All in One CPU Card Series User s Manual 8 5 Chipset Features Setup This Setup menu controls the configuration of the motherboard chipset ROM PCI ISA BIOS CHIPSET FEATURES SETUP AWARD SOFTWARE INC SDRAM RAS to CAS Delay 3 Auto Detect DIMM PCI Clk Enabled SDRAM RAS Precharge Time v3 Spread Spectrum Disabled SDRAM CAS latency Time ES CPU Host Clock Default SDRAM Precharge Control Disab CPU Warning Temperature Disabled DRAM Data Integrity Mode Non E Current System Temp 49 C 120 F System BIOS Cacheable Disab Current CPU Temperature 490C 1200F Video BIOS Cacheable Disab Current CPU FAN1 Speed ORPM Video RAM Cacheable Disab Current CPU FAN2 Speed ORPM 8 Bit 1 0 Recovery Time I Vcore V 1 63V VTT V 1 50V 16 Bit 1 O Recovery Time cd 3 3V 3 37V 5V 5 05V Memory Hole At 15M 16M Disabled 12V 12 34V 12V 11 78V Passive Release Enabled 5V 5 16V Delayed Transaction Disabled AGP Aperture Size MB 64 ESC Quit AN gt Select Item F1 Help PU PD Modify F5 Old Values Shift F2 Color F6 Load BIOS Defaults F7 Load Setup Defaults SDRAM RAS to CAS Delay During DRAM refresh both rows and columns are addressed separately This field allows you to determine the timing of transition from Row Address Strobe RAS to Column Address
30. en installing a new CPU the jumpers including CPU type CPU Clock CPU Voltage and Bus Clock may need to be adjusted Make sure all the settings are correct for the installed CPU to prevent any damage to the CPU 4 2 BIOS The system BIOS used in SBC8163 is Award Plug and Play BIOS The SBC8163 contains a single 2MB Flash EPROM For more detailed information refer to Chapter 8 for a complete description of the BIOS setup utility and the available features accompanying it Hardware Description 13 SBC8163 Socket370 All in One CPU Card Series User s Manual 4 3 I O Port Address Map The CPU card communicates via I O ports It has a total of 1KB port addresses that can be assigned to other devices via I O expansion cards Devices DMA controller 1 Interrupt controller 1 Timer Keyboard controller Real time clock NMI 080 09F DMA page register 0A 0 OBF nterrupt controller 2 OFO Clear math coprocessor busy signal OC 0 ODF DMA controller 2 Reset math coprocessor OF8 OFF ath processor 12 Disable watchdog timer operation read 121 Enable watchdog timer operation read 122 Watchdog 1F0 1F8 Fixed disk controller 200 207 Game port 300 31F Prototype card 360 36F Reserved 378 37F Parallel port 1 3B0 3BF MDA video card including LPT1 3C 0 3CF EGA card 3D0 3DF CGA card 3F0 3F7 Floppy disk controller 3F8 3FF Serial port 1 COMI 2F8 2FF Serial port 2 COM2 Address 000 01F 020 03F 040 05F 060 06F 070 07F o 14
31. end ints cnayen7 3 Transmit Data TXD 5 8 6 Clear to Send CTS Data Terminal Ready DTR 8 Ring Indicator RI 5V 12V 5 9 jGmwd oND CN16 GND looooo 60 Connector Pin Assignments SBC8163 Socket370 All in One CPU Card Series User s Manual USB Connector CN 10 USB Vcc USB Vcc USB P0 4 USBP1 5 useror 6 USBPI 7 GND leloo 9 Noconnectr 10 Noconnector Case Fan Connector CN 23 CPU Fan Connector CN 24 WAKE ON LAN Connector CN4 5VSB Connector Pin Assignments 61 SBC8163 Socket370 All in One CPU Card Series User s Manual This page does not contain any information 62
32. he driver iles Ethernet 25 SBC8163 Socket370 All in One CPU Card Series User s Manual This page does not contain any information 26 SBC8163 Socket370 All in One CPU Card Series User s Manual Chapter 7 SCSI Controller 7 1 Introduction The onboard LSI integrated Duak Channel Ultra2 SCSI provides two SCSI 3 interfaces that require BIOS support The dual channel LSI integrated SCSI provides 16 bit Low Voltage Differential LVD and Single Ended SE SCSI solutions for your computer This supports legacy Fast SCSI devices Ultra SCSI devices Ultra2 SCSI devices and the newest Ultra160 devices PCI SCSI Device Management System SDMS software operates the chipset but the design of the chipset does not prevent other software to be used with it BIOS support for this chipset is incorporated in the SBC8163 CPU card BIOS 7 2 Features Two separate SCSI channels 16 bit SE LVD Automatically enabled termination One 68 pin high density for channel A One 68 pin high density and one 50 pin header for channel B Fast Ultra and Ultra2 data transfer capability SCSI Plug and Play SCAM SCSI Configured AutoMatically Serial NVRAM Non Volatile Random Access Module on each channel for user configuration utility and SCAM information storage 4LED connectors for display of SCSI channel state SCSI Controller 27 SBC8163 Socket370 All in One CPU Card Series User s Manual 7 3 Driver Support LSI Logic currently pr
33. ives e Serial Ports Two 16550 UARTs ports with 16 byte as one RS 232 and one RS 232 422 485 Parallel Ports One parallel port with ECP EPP SPP supported e VGA Controller W AGP interface controller with onboard 8MB SDRAM W VGA chipset ATI Rage XLAGP 2X supporting CRT displays W Supports up to 1600x1200 16 bit color resolution on non interlaced CRT monitors e Ethernet E Intel 82559 PCI Bus 10 100M Base T W Onboard Wake On LAN via ATX power supply W Onboard RJ 45 connector 2 Introduction SBC8163 Socket370 All in One CPU Card Series User s Manual Ultra3 Wide SCSI W LSI Symbios SYM53C 1010 PCI Bus Ultra 3 Wide SCSI interface E Two 68 pin 16 bit differential Ultra 3 Wide SCSI ports and one 50 pin 8 bit Ultra SCSI port W Connectsup to 30 SCSI peripherals whit Ultra 3 Wide SCSI feature E Provide data transfer rates up to 160MB sec whit Ultra3 Wide SCSI 80MB sec whit Ultra 2 Wide SCSI 40M B sec whit Ultra Wide SCSI and 20MB sec with Ultra SCSI interface e USB Interface 2 USB ports USB Spec Rev 1 1 compliant IrDA 1 IrDA pin header for wireless communication Hardware Monitoring Winbond W83781D controller monitoring for CPU System temperature system voltage and fan speed e Watchdog Timer m Generates a system reset m Software programmable time interval and jumper selectable E 64 levels 0 5 8 5 80 50 800 100 1600 seconds e SSD Supports M Systems DiskOnChip 2000 serials e Dimensions 122 W x
34. ll stop for all other errors 8 4 BIOS Features Setup This section allows you to configure and improve your system and allows you to set up some system features according to your preference ROM PCI ISA BIOS BIOS FEATURES SETUP AWARD SOFTWARE INC Virus Warning Disabled Video BIOS Shadow Enabled CPU Internal Cache Enabled C8000 CBFFF Shadow Disabled External Cache Enabled CC000 CFFFF Shadow Disabled CPU L2 Cache ECC Checking Enabled D0000 D3FFF Shadow Disabled Processor Number Feature Enabled D4000 D7FFF Shadow Disabled Quick Power On Self Test Enabled D8000 DBFFF Shadow Disabled Boot Sequence CA SCSI DC000 DFFF Shadow Disabled Swap Floppy Drive Disabled Boot Up Floppy Seek Disabled Boot Up NumLock Status On Gate A20 Option Fast Typematic Rate Setting Disabled Typematic Rate Chars Sec 6 Typematic Delay Msec 250 Security Option Setup PS 2 mouse function control Enabled Quit V Select Item PCI VGA Palette Snoop Disabled Help PU PD Modify OS Select For DRAM gt 64MB Non 052 Old Values Shift F2 Color Report No FDD For WIN 95 Yes Load BIOS Defaults Load Setup Defaults 34 Award BIOS Utility SBC8163 Socket370 All in One CPU Card Series User s Manual e Virus Warning This item protects the boot sector and partition table of your hard disk against accidental modifications If an attempt is made the BIOS will halt the system and display a warning
35. m such a mode In effect the system remains alert for anything that occurs to a device that is configured as On even when the system is in power down mode Award BIOS Utility 43 SBC8163 Socket370 All in One CPU Card Series User s Manual e PCI VGA Act Monitor When Enabled any video activity restarts the global timer for Standby mode The default value is Disabled e Soft Off by PWR BTTN This only works with systems using an ATX power supply It also allows tser to define the type of soft power OFF sequence the system will follow This option follows the conventional manner systems perform when power is turned OFF Instant Off is a soft power OFF sequence requiring only the switching of the power supply button to OFF Insta nt O ff default Upon turning OFF system from the power switch this option will delay the complete system power OFF sequence by approximately 4 seconds Within this delay period system will temporarily enter into S uspend Mode enabling you to restart the system at once Delay 4 Sec e PowerOn by Ring An input signal on the serial Ring Indicator RI line in other words an incoming call on the modem awakens the system from a soft off state e Resume by Alarm When Enabled your can set the date and time at which the RTC real time clock alarm awakens the system from Suspend mode PCI LAN Card Onboard LAN Wakeup Wake On LAN alows your computer to be booted from another computer via a netw
36. message If this occurs you can either allow the operation to continue or run an anti virus program to locate and remove the problem NOTE Many disk diagnostic programs which attempt to access the boot sector table can cause the virus warning If you will run such a program disable the Virus Warning feature e CPU Internal Cache External Cache Cache memory is additional memory that is much faster than conventional DRAM system memory CPUs from 486 type on up contain internal cache memory and most but not all modern PCs have additional external cache memory When the CPU requests data the system transfers the requested data from the main DRAM into cache memory for even faster access by the CPU These items allow you to enable speed up memory access or disable the cache function By default these are Enabled CPU L2 Cache ECC Checking When enabled this allows ECC checking of the CPU s L2 cache By default this field is Enabled e Quick Power On Self Test When enabled this field speeds up the Power On Self Test POST after the system is turned ON If it is set to Enabled BIOS will skip some items e Boot Sequence This field determines the drive that the system searches first for an operating system The available options are E A C SCSI E C A SCSI C CDROM A CDROM C A E D A SCSI m SCSI C A Wm C only E LS ZP C m SCSLA C E The default value is 4 C SCSI Award BIOS Utility 35 SBC8163 Socket37
37. ody M Wear a wrist grounding strap available from most electronic component stores when handling boards and components Trademarks Acknowledgments AXIOMTEK isa trademark of AXIOMTEK Co Ltd IBM isa registered trademark of International Business Machines Corporation MS DOS and Windows 95 98 NT 2000 are trademarks of Microsoft Corporation Award isa trademark of Award Software Inc IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation Intel and Celeron Pentium lll are trademarks of Intel Corporation ATI isa trademark of ATI Technologies Inc Other brand names and trademarks are the properties and registered brandsof their respective owners This page does not contain any information Table of Contents Chapter 1 Introduction l l General DESC Plan uzdsnesuoss eura hb ipd eLEESR 1 1 2 DBCIHEAEHOBS siririn ea een ea 2 1 3 Utilities SUDDOFITQU siconsciiataic irrita 3 1 4 Board Dimensions anios 4 Chapter 2 Jumpers and Connectors L BOSOIOESUVOUE eene sas Ia Ei ES UM SE 5 2 2 Iumper nn 6 2 2 1 Internal Keyboard Connector Power Selection J P16 6 2 2 2 VGA Controller Interrupt Control JP4 ri 2 2 3 Power Supply Type Selection JP11 ssss 7 2 2 4 Watchdog Trigger Mode Setting J P14 7 2 2 5 DiskOnChip Memory Segment J P12 sssss 7 2 2 60 SCSI Function ntenupt Control P7 cci gue
38. olor The section below the setup items of the Main Menu displays the control keys for this menu Another section located at the bottom of the Main Menu just below the control keys section displays information on the currently highlighted item in the list NOTE If you find that your computer cannot boot after making and saving system changes with Setup the Award BIOS via its built in override feature resets your system to the CMOS default settings We strongly recommend that you avoid making any changes to the chipset defaults These defaults have been carefully chosen by both Award and your system manufacturer to provide the absolute maximum performance and reliability 30 Award BIOS Ulility SBC8163 Socket370 All in One CPU Card Series User s Manual 8 3 Standard CMOS Setup Standard CMOS Setup allows you to record some basic hardware configurations in your computer system and set the system clock and error handling If the motherboard is already installed in a working system you will not need to select this option You will need to run the Standard CMOS option however if you change your system hardware configurations the onboard battery fails or the configuration stored in the CMOS memory was lost or damaged ROM PCI ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE INC Date mm dd yy Sat Jul 12000 Time hh mm ss 00 00 00 HARD DISK TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master Primary Slave
39. ork by sending a wakeup frame or signal These options enables or disables the wakeup function connected to the Onboard LAN chip or external LAN card connector PCI LAN Card Wakeup e IRQ 8 Break Suspend You can turn on or off monitoring of IRQ8 the Real Time Clock so it does not awaken the system from Suspend mode The default value is Disabled 44 Award BIOS Ulility SBC8163 Socket370 All in One CPU Card Series User s Manual 8 6 3 Reload Global Timer Events When Enabled an event occurring on each device listed below restarts the global time for Standby mode e IRQ3 7 9 15 NMI The default value is Disabled Primary I DE O The default value is Disabled Primary IDE 1 The default value is Disabled Secondary I DE 0 The default value is Disabled Secondary IDE 1 The default value is Disabled Floppy Disk The default value is Disabled Serial Port The default value is Enabled Parallel Port The default value is Disabled 8 7 PNP PCI Configuration This option configures the PCI bus system All PCI bus systems on the system use INT thus all installed PCI cards must be set to this value ROM PCI ISA BIOS PNP PCI CONFIGURATION AWARD SOFTWARE INC PNP OS Installed No Assign IRQ For VGA Enabled Resources Controlled by Auto Reset Configuration Data Disabled Assign IRQ For USB Enabled ESC Quit v gt Select Item Help PU PD Modify Old Values Shift F2 Color Load BIOS Def
40. ou are installing drivers Your Display Driver Folders in the Product Information CD ROM contain drivers for several versions of certain applications For your driver to operate properly you must install the driver for your version of the application program NOTE Before you begin the driver software installation please see the detail of installation procedure from the driver utility in the Product Information CD ROM 24 Display Drivers SBC8163 Socket370 All in One CPU Card Series User s Manual Chapter 6 Ethernet 6 1 Introduction The SBC8163 is equipped with a high performance Plug and Play Ethernet interface which is fully compliant with the IEEE 802 3 standard and consisting of a RJ 45 connector CN25 6 2 Features e 10Mb s and 100Mb s operations Supports 10Mb s and 100Mb s N Way auto negotiation Full duplex capability Full compliance with PCI Revision 2 1 PCI Bus Master data transfers 6 3 Drivers Supported Bundled with popular software drivers the SBC8163 Ethernet interface allows great flexibility to work with all major networking operating systems including Novell NetWare v2 x v3 x v4 x Microsoft LAN Manager Win3 1 Win NT Win95 IBM LAN Server SCO UNIX or other ODI NDIS and Packet drive compliant operating systems NOTE Before you begin the driver software installation please see the detailed installation procedure from the Product Information CD ROM and be sure to uoce installation and backup copies of t
41. ovides Symbios PCI to SCSI device drivers for the MS DOS6 0 Windows 3 1 Windows 95 98 Windows NT 3 5x 4 0 Windows 2000 SCO UNIX Open Server Release 5 UnixWare 2 1 x and 7 Solaris 7 Linux NetWare 3 12 4 11 5 NOTE Before you begin the driver software installation please see the detail of installation procedure from the driver utility in the Product Information CD ROM and be sure to make installation and backup copies of the SCSI Driver Diskettes Refer to the SCSI User s Manual provided in the Product Information CD ROM for more information 28 SCSI Controller SBC8163 Socket370 All in One CPU Card Series User s Manual Chapter 8 Award BIOS Utility Chapter 8 describes the different settings available in the Award BIOS that comes with the SBC8163 CPU card Also contained here are instructions on how to set up the BIOS configuration 8 1 BIOS Introduction The Award BIOS Basic Input Output System installed in your computer system s ROM supports Intel Celeron processors in a standard IBM AT compatible I O system The BIOS provides critical low level support for standard devices such as disk drives serial and parallel ports It also adds virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system 8 2 BIOS Setup The Award BIOS provides a Setup utility program for specifying the system configurations and settings The BIOS ROM of the system stores the Setup
42. port gt Normal default value NOTE The UART Mode Select will not appear on the menu once you disable the setting of Onboard Serial Port 2 When UART Mode Select is set as ASKIR or IrDA the options RxD TxD Active and IR Transmittion delay will appear e IR Transmission delay Full duplex mode permits simultaneous two direction transmission Half duplex mode permits transmission in one direction only at a time If no infrared port is present in the system select Disabled The default value is Enabled Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I O address The options available are 378H IRQ7 278H IRQ5 3BC IRQ7 Disabled e Parallel Port Mode Select an operating mode for the onboard parallel printer port Select Normal unless your hardware and software require one of the other modes offered in this field The options available are EPP1 9 ECP SPP ECPEPP1 7 EPP1 7 Award BIOS Utility 51 SBC8163 Socket370 All in One CPU Card Series User s Manual e ECP Mode Use DMA Select a DMA channel for the parallel port for use during ECP mode The available choices are 3 and 7 e EPP Mode Select Select EPP port type 1 7 or 1 9 8 11 Supervisor User Password These two options set the system password Supervisor Password sets a password that will be used to protect the system and Setup utility User Password sets a password that will be used exclusively on th
43. pported ssp tet epeo soia 25 Chapter 7 SCSI Controller 7 a a A 27 Jam DESUUUES dare rios 27 1 3 Driver SUPPO 222 2 022 2eeqeEbedaPqAF ee RAS Rees 28 Chapter 8 Award BIOS Utility EL BIOS DAIFCHTHE UO siii dus qnas 46s bis 29 8 2 BIOS SODHD upssesisdamiissa sas bias iii 29 8 3 Standard CMOS Setup sanada aaa 3l 8 4 BIOS Features SOT sissia corra 34 8 5 Chipset Features Setup cient 38 8 6 Power Management Setup 41 SiGe EM TUNES iaa dit 43 8 6 2 PM EVG tsi citi sc poe od QNO cda Pedo iR cR oen o Ee o OR nadam 43 8 63 Reload Global Timer Events titer trn 45 B 7 PNPIPLICOR ISGUUOTIOR 22s I imiinien 45 8 8 Load BIOS Defaults ques spsaastasmaGas ds Endad 47 8 9 Load Setup Defaults seio a E PEE RERIARE KE UPS 48 8 10 Integrated Peripherals irent 49 8 11 Supervisor User Password 52 8 12 IDE HDD Auto Detect tioD3cneiecesesiiee ke esa 33 8 13 Save amp EM SQUID rrisin eton 54 8 14 Exit Without SAVING sssporsriinsina old scinbisa 55 Appendix A Watchdog Timer Using the Watchdog Function Lue en 57 Table of Contents vii Appendix B Connector Pin viii Assignments 40 pin IDE Interface Connector CNO 59 Floppy DISK Connection CN iic somsstsse spectent ti seta tob tere cc tela pa dont 59 Parallel Pont Connector CN aa nata d coe ra loda co tcu cR QU 60 Seal Ponts PiMASSIGNMENE rica eet rne adotuus 60 USB Connector CN IO au cccipera psa aa ai died ia adia ai 61 Case Fan Connection C
44. r Short pins 4 6 when connecting the CPU card to an internal buzzer When connecting an external speaker set these jumpers to Open and install the speaker cable on pin 8 and pin 2 External SMI Button Switch This switch enables the connection between the SBC8163 based system and the installed hardware Pins 11 amp 12 of CN11 support the SMI switch function ATX Power On Off Button This 2 pin connector designated at Pins 13 amp 14 of CN11 connects the ATX power button of the front panel to the SBC8163 CPU card allowing user to control the power on off state of the ATX power supply This jumper is only useful when installing an ATX power supply and CN17 cable to the system 16 Hardware Description SBC8163 Socket370 All in One CPU Card Series User s Manual System Reset Switch Pins 17 amp 18 of CN11 connect to the case mounted reset switch and allow rebooting of your computer instead of turning OFF the power switch This is a preferred method of rebooting in order to prolong the life of the system s power supply HDD Activity LED This connector extends to the hard drive activity LED on the control panel This LED will flash when the HDD is being accessed Pins 19 amp 20 of CN11 connect the hard disk drive and the front panel HDD LED Pins 19 is and pin 20 is assigned as Reserved pins Pins 10 15 and 16 of CN11 are reserved pins 4 6 Enhanced IDE Interface Connector The SBC8163 includes a PCI bus enh
45. r NMI OUT 120 00H Can be disable at any time 57 SBC8163 Socket370 All in One CPU Card Series User s Manual 0 5 sec 5 secs 50 secs 100 secs Esse NND ERE Ga 3 6 35secs 35secs 350secs 7 0secs 58 Watchdog Timer SBC8163 Socket370 All in One CPU Card Series User s Manual Appendix B Connector Pin Assignments 40 pin IDE Interface Connector CN 6 4 Daags 5 datas 6 Datas 7 datas 8 Data 9 Dataa 20 23 26 29 32 35 38 40 fono Floppy Disk Connector CN 2 Description Pin Pin Description connector 5 6ND 6 8 index 9 torenableA 11 GND 22 Drive select B STEPS Jal Track 0 c iw c iw olz olz connector 0 iw j N DO lo Az iw iw 0 o iw Ui DIO m 00 iw tor enable B ection o iw N e z zo WIWININ W O jN B O 0 O o zia iw iw te data zo te gate zi oO fab ad datas zo c iw WININININ A EA N O D W O X Pp c iw te protect Pin 4 jw isk change Connector Pin Assignments 59 SBC8163 Socket370 All in One CPU Card Series User s Manual Parallel Port Connector CN3 ololololololo O O O O O 0O O o iw Serial Ports Pin Assignment Data Carrier Detect DCD 5V 12V 6 2 jDatSetRealy DSR 7 4 Trequestto S
46. t setting is 3 16 Bit O Recovery Time This option specifies the length of the delay in sysclks inserted between consecutive 16 bit I O operations The settings are 1 2 3 4 5 6 7 or 8 The default setting is 2 Memory Hole at 15MB 16MB In order to improve performance certain space in memory can be reserved for ISA cards This field allows you to reserve 15MB to 16MB memory address space to ISA expansion cards This makes memory from 15MB and up unavailable to the system Expansion cards can only access memory up to 16MB By default this field is set to Disabled Passive Release When enabled CPU to PCI bus accesses are allowed during passive release Otherwise the arbiter only accepts another PCI master access to local DRAM Delayed Transaction The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification version 2 1 The default setting is Disabled Award BIOS Utility 39 SBC8163 Socket370 All in One CPU Card Series User s Manual AGP Aperture Size MB The field sets aperture size of the graphics The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any translation The options available are 4M 8M 16M 32M 64M 128M and 256M The default setting is 64M CPU Warning Temperature This field se
47. tered by your system may be a result from loose or improper connections Ensure that all connectors are in place and firmly attached The following table lists the function of each connector on the SBC8163 Their corresponding pin assignments are described in Chapter 4 and Appendix B Connectors Primary IDE Connector FDD Connector Printer Port Connector COM1 SBC8163VES And SBC8163VE Only Secondary IDE Connector 50 pin Narrow SCSI Connector COM2 68 pin Ultra3 2 Wide SCSI Connector With Channel 1 68 pin Ultra3 2 Wide SCSI Connector With Channel 2 General Output C onnector Reserved Fan Power Connector 1 IrDA Connector Ethemet Connector SBC8163VES amp VE Only COMI SBC8163V Only Jumpers and Connectors Label CN CN CN CN CN CN 1 2 3 4 CN a CN11 a O E Re Re N 5 6 7 8 CN9 Fan Power Connector 2 CN26 CN10 cN12 Watc h Dog Activity LED Connector CN13 4 5 16 Label ACPI Connector 17 VGA Connector CN18 Extmal Battery CN20 Connector USB Connector CN22 PS 2 Keyboard 23 Connector PS 2 Mouse Connector Keyboard Mouse Connector a a a JO N25 SCSI Channel 1 LVD Mode directives LED Connector SCSI Channel 2 LVD Mode directives LED Connector iw c pA N SCSI Channel 2 Activity D7 LED Connector SCSI Channel 1 Activity LED Connector Ethe met Boot ROM U16 Socket DiskOnChip Socket
48. the Setup utility without saving the modifications Typing N will return you to Setup utility ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURA Quit Without Saving Y N N ETUP LOAD BIOS DEFAULT SAVING LOAD SETUP DEFAULTS Esc Quit v gt Select Item F10 Save Exit Setup Shift F2 Change Color Abandon all Data amp Exit Setup Award BIOS Utility 55 SBC8163 Socket370 All in One CPU Card Series User s Manual This page does not contain any information 56 SBC8163 Socket370 All in One CPU Card Series User s Manual Appendix A Watchdog Timer Using the Watchdog Function The SBC8163 CPU card uses version 2 0 of the watchdog timer This onboard WDT generates either a system reset or non maskable interrupt NMI depending on the settings made on jumper JP12 of SBC8163 Follow the steps below to enable and program the watchdog function of SBC8163 Start 1 Un Lock WDT y Set multiple 1 4 1 Set base timer 0 F 1 WDT counting 1 re set timer 4 IF No re set timer E IF to disable WDT Watchdog Timer OUT 120H 0AH enter WDT function OUT 120H OBH enable WDT function OUT 120 ONH N 1 2 3 or 4 OUT 121 0MH M 0 1 2 F OUT 121 0MH M 0 1 2 F WDT time out generate RESET o
49. troduction The VGA chipset used on the SBC8163 that can drive a wide range of monochrome and color flat panels including Single Drive SS and Dual Panel Dual Drive DD passive STN and active matrix TFT MIM LCD EL and Plasma panels The 69000 supports an additional 256Kx16 DRAM providing a 32 bit video memory bus The 69000 accelerator can support up to 64 gray scales on monochrome panels up to 226 981 colors on passive STN LCDs and up to 16M colors on 24 bit active matrix LCDs It also offers a variety of programmable features to optimize display quality including tall font stretching fast vertical centering and programmable vertical stretching in graphics for handling modes with less than 480 lines 5 2 Features AGP interface controller with onboard 8MB SDRAM VGA chipset ATI Rage XL AGP 2X supporting CRT displays e Display memory supports up to 1600x1200 16 bit color resolution on non interlaced CRT monitors Display Drivers 23 SBC8163 Socket370 All in One CPU Card Series User s Manual 5 3 Drivers Supported The Rage XL is fully compatible with the VGA graphics standard at the register gate and BIOS levels The manufacturer supplies fully VGA compatible BIOS end user utilities and drivers for common application programs e g Microsoft Windows ATI s drivers for Windows include a Big Cursor setting and fast panning scrolling capabilities Make sure you know the version of the application for which y
50. ts the threshold temperature at which an alert is sounded through the system s speaker An onboard thermal sensor monitors the CPU temperature to prevent CPU overheating Current System CPU Temp These read only fields reflect the functions of the hardware thermal sensor that monitors the chip blocks and system temperatures to ensure the system is stable Current CPU Fan1 Fan2 Speed These optional and read only fields show the current speeds in RPM revolution per minute for the CPU fan and chassis fan as monitored by the hardware monitoring IC e Vcore V VTT V 3 3V 12V 12V 5V 5V These optional and read only fields show the current voltages in the voltage regulators and power supply as monitored by the hardware monitoring IC 40 Award BIOS Utility SBC8163 Socket370 All in One CPU Card Series User s Manual 8 6 Power Management Setup The Power Management Setup allows you to save energy of your system effectively It will shut down the hard disk and turn OFF video display after a period of inactivity ROM PCI ISA BIOS POWER MANAGEMENT SETUP AWARD SOFTWARE INC ACPI function Disabled Reload Global Timer Power Management User Define IRQ 3 7 9 15 NMI Disabled PM Control by APM Yes Primary IDE 0 Disabled Video Off Method V H SYNC Blank Primary IDE 1 Disabled Video Off After Standby Secondary IDE 0 Disabled MODEM Use IRQ 3 Secondary IDE 1 Disabled Doze Mode Disab Floppy Disk Disa
51. tting is required The following table is the pin assignments for the CRT VGA connector 18 Hardware Description SBC8163 Socket370 All in One CPU Card Series User s Manual CN18 CRT VGA Connector Pin Assignment 1 Red 2 Green a Bue Pa qua 15 GND J e6 J AGND 7 AGND Joe AGND 9 qua 4 8 Ethernet Connector The RJ 45 connector is used for Ethernet To connect the SBC8163 to 10 Base T or 100 Base T hub just plug one end of the cable into the CN15 and connect the other end phone jack of the cable to a 10 Base T hub 4 9 SCSI Connector The SBC8163 provides three SCSI connectors for 160Mbps 80Mbps 40Mbps and 20Mbps SCSI devices This feature is not available on SBC8163 board CN10 Ultra3 Wide SCSI Connector 68 pin supports up to 160Mbps SCSI devices CN9 Ultra3 Wide SCSI Connector 68 pin supports up to 160Mbps SCSI devices CN6 Narrow SCSI Connector 50 pin supports 20Mbps SCSI devices 4 10 Floppy Disk Controller The SBC8163 provides a 34 pin header type connector CN2 supporting up to two floppy drives The floppy drives may be any one of the following types 5 25 360KB 1 2MB and 3 5 720KB 1 44MB 2 88MB The CN2 pin assignment is listed in Appendix B Hardware Description 19 SBC8163 Socket370 All in One CPU Card Series User s Manual 4 11 Parallel Port Interface The SBC8163 onboard CN3 is a multi mode parallel port able to support e Standar

SBC8163 Series User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents