Heat/Light/Vent
Contents
1. GOLDAIR Select Operating Instructions Heat Light Vent Model GSHL50 General Care and Safety Guide Thank you for choosing a Goldair Select Heat Light Vent This Goldair Select Heat Light Vent has been designed and manufactured to high standards of engineering and with proper use and care as described in this leaflet instructions carefully 10 11 Use only the voltage specified on the rating label of the appliance Do not cover or restrict airflow as the appliance may overheat and become a fire risk Do not cover grill block entry or exhaust of airflow by placing any of these areas against any surface Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock fire or damage to the appliance Do not operate after the appliance malfunctions or has been dropped or damaged in any manner Return to a qualified electrical person for examination electrical service or repair This appliance is intended for household use only and not for commercial or industrial use Use this appliance only as described in this manual Any other use is not recommended by the manufacturer and may cause fire electrical shock or injury The common cause of overheating is deposits of dust or fluff in the appliance Ensure these deposits are removed regularly by switching the appliance off at the mains and vacuum cleaning the air vents and grills Do not use abrasi2. device will automatically turn the appliance off if the appliance is not in the appropriate operating position The second device automatically disconnects amp reconnects the appliance at a preset temperature The third device disconnects the appliance permanently in case of overheating by means of a thermal fuse it is non resettable CARE AND CLEANING The appliance requires regular cleaning to ensure trouble free operation Turn off the mains supply before cleaning Ensure that the appliance has been allowed to cool down completely before cleaning Use a damp cloth not wet to wipe the exterior of the appliance to remove dust and dirt Use a vacuum cleaner to remove dust and fluff from around the grills Never use solutions such as benzene thinners or polishing agents Ensure the appliance is dry before turning the mains supply back on Do not attempt to dismantle the appliance There are no user serviceable parts For service or repair contact an authorised electrical service technician CAUTION The Heat Light Vent generates heat during use Proper precautions must be taken to prevent the risk of burns scalds fires or other damage to persons Do not use this Heat Light Vent with a programmer timer separate remote control system or any other device that switches the Heat Light Vent on automatically IMPORTANT NEVER HEAT LIGHT VENT COVER THIS PROOF OF PURCHASE To receive warranty retain receipt as proo
3. ay ensuring that it is positioned centrally IMPORTANT NOTE Over tightening of heat lamps or light bulbs may result in damages to the lamp holders or lamps take care when removing and replacing heat lamps bulbs The appliance is to be installed so that the pull cord and other controls cannot be touched by a person in the bath or shower Operating your Heat Light Vent WARNING Keep all objects at least 1 metre from the front sides and rear of the appliance USER INSTRUCTIONS Your Heat Light Fan unit comes with a wall switch included Once wired correctly by your electrician you need to simply follow the below instructions To turn the centre light bulb on press the LIGHT switch down and up to turn off To the ventilation fan on press the FAN switch down and up to turn off To turn the 2 heat lamps on press the HEAT switch down and up to turn off AIR FLOW REQUIREMENTS For maximum efficiency to remove steam and odours there must be an adequate air flow within the room To obtain maximum air flow ensure there is a gap under doors or open windows slightly A good test for this is that the fan should not change speed or sound when you close or open the bathroom door IMPORTANT NOTE Always turn the fan on when using the heat lamps to minimise any undue heat build up in the unit HEAT GOLDAIR GOLDAIR Select SAFETY DEVICE This appliance has three protection devices The first
4. f of purchase Refer to back of booklet SUPPORT AND TECHNICAL ADVICE Goldair Select New Zealand Monday Friday 8am 5pm Phone 64 0 9 917 4000 Phone 0800 232 633 info cdb co nz Goldair Select Australia Monday Friday 8am 5pm Phone 61 0 3 9336 4423 Phone 1300 465 324 info cdbgoldair com au CDB 4 GOLDAIR One Year Warranty Thank you for purchasing this Goldair Select product Your product is warranted against faults and manufacture when used in normal domestic use for a period of one year In non domestic use Goldair limits the voluntary warranty to three months Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during the warranty period This warranty excludes damage caused by misuse neglect shipping accident incorrect installation or work carried out by anyone other than a qualified electrical service technician PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY The benefits given to you by this warranty are in addition to other rights and remedies available to you under law in relation to the goods or services to which this warranty relates In Australia our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods re
5. good test for this is that the accordance with the AS NZS 3000 2007 and any fan should not change speed or sound when local regulation information for mounting in damp you close or open the bathroom door areas please consult your local electrician for 11 220 240V 50Hz electrical supply is required information The unit can be connected to a lighting or The unit can be installed in any room that power circuit if loading permits All electrical requires direct radiant heating and circulated air work must be carried out by a registered flow such as bathrooms ensuites laundries etc electrician in accordance with AS NZS The unit must be installed in flat ceilings with a 3000 2007 please consult your local minimum height of 2 metres from the floor electrician for information A three gang switch Do not install the unit directly above shower or is included to so the user can independently bath recesses or enclosures switch the Ventilation Heat and Light on and The unit must not be installed in a position off This needs to be installed in a position where water may splash onto the heat lamps where it cannot be reached from the bath or At least 220mm height clearance in the ceiling shower cavity is required to ensure sufficient ventilation 12 Heat lamps and light bulbs supplied with the unit are test bulbs only these are not covered under the appliance warranty Replacement Heat lamps and light bulbs can be purchased from your local re
6. he unit at this time Remove the unit from the ceiling and connect the wiring to the terminal block as per the wiring diagram EARTH This terminal block is on one corner of the back of the unit NEUTRAL ACTIVE Insert the unit into the hole and secure as detailed in point 4 above S W LIGHT Hold the fascia against the body of the appliance and S W FAN the ceiling then attach the securing spring clips to S W HEAT hold the fascia in place The unit may be mounted either between joists using the inbuilt clip fasteners or against a joist using a screw through the flange plate The approximate cut out size of the unit is 355 x 185mm Please note this is only an approximate measurement and any installation would require a measurement against the physical product to ensure the best fit Mark the ceiling with a pencil showing the area of ceiling to be cut IMPORTANT NOTE Goldair takes no responsibility for those instances where the physical product is not measured first before the hole is cut in the ceiling Before commencing cutting ensure that the area behind the intended location is clear of all cables pipes and joists Once clear cut out the section along the previously marked lines Now screw in the 275W heat lamps provided into the lamp holder through the holes provided in the fascia The globes should be screwed in firmly to ensure a good electrical contact but don t over tighten Fit the small centre light bulb in the same w
7. k or is not working properly contact the place of purchase or the Goldair Customer Services Team Repair work on the appliance by unqualified persons can cause serious risk to the user There are no user serviceable parts installed in the unit including the pull cord Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards This unit is not supposed to be used in or around locations where foodstuffs works of art or delicate articles of science etc are stored Indoor use only Children should be supervised to ensure that they do not play with the appliance It is important that you do not cover this heater 650W 2x 275W E27 Heat Lamps 60W R63 Centre Light Bulb 40W Centrifugal Fan Motor General Care and Safety Guide This appliance is designed only to be used as a fixed Heat Light Vent appliance installed into the ceiling If the appliance is installed or used for any other purpose the warranty will be void for moisture to disperse The unit must also be installed at least 400mm away from the walls Installation of this appliance must be completed 10 For maximum efficiency to remove steam and by a registered electrician odours there must be an adequate air flow Handle appliance with care remove the bulbs within the room To obtain maximum air flow during installation ensure there is a gap under doors or open The unit must be located and installed in windows slightly A
8. paired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure In New Zealand this warranty is additional to the conditions and guarantees of the Consumers Guarantee Act 1993 Goldair New Zealand Goldair Australia CDB Goldair CDB Goldair Australia Pty PO Box 100 707 PO Box 574 N S M C South Morang Auckland Victoria 3752 Phone 64 0 9 917 4000 Phone 61 0 3 9336 4423 Phone 0800 232 633 Phone 1300 GOLDAIR 1300 465 324 www goldair co nz www goldair com au Goldair One Year Warranty IMPORTANT Please complete and retain this warranty card Name Address Place Of Purchase Date of Purchase Name Of Product Model Number Attach a copy of the purchase receipt to this warranty card Due to continual design improvements the product illustrated in this User Manual may differ slightly from the actual product
9. tailer Installing your Heat Light Vent Always choose a safe location for the Heat Light Vent keeping in mind the safety precautions outlined Ensure all packaging has been removed from the unit before use IMPORTANT NOTE All electrical work and installation of this product must be performed by a registered electrician in accordance with AS NZS 3000 2007 INSTALLATION INSTRUCTIONS Note The unit is fitted with a safety thermal switch which will activate the fan to cool the unit if the heat generated by the heat lamps exceeds a certain level lt is imperative that this feature is enabled Ensure power to the circuit to be used has been isolated at the power board before carrying out any electrical work WIRING DIAGRAM Remove the lamps from the housing by unscrewing them anticlockwise Then remove the decorative fascia from the housing by removing the spring clips that hold it in place Insert the unit into the hole being sure to pull the side springs inward so that the body can pass through the hole without damaging the plaster Ensure that the unit is held securely in place by clips It is essential that additional screws not supplied are used to aid holding the unit in the ceiling Screw holes are provided in the flange for this purpose 2 strips of timber one on each side should be placed behind the holes inside the ceiling to give the screws something to anchor to and to provide some reinforcing Do not secure t
10. ve cleaning products on this appliance Clean with a damp cloth not wet rinsed in hot soapy water only Always switch off at the mains supply before cleaning Do not connect the appliance to mains supply until completely assembled and adjusted Do not operate the appliance with wet hands 12 Do not use this appliance in a window as rain may cause electric shock TECHNICAL SPECIFICATION Model No Supply Wattage GSHL50 220 240VAC 50Hz 13 14 15 17 18 19 20 21 22 23 24 25 will give you years of useful service Please read these Do not use the appliance to dry clothes Do not mount appliance close to any other heat source Do not operate in areas where petrol paint or other flammable liquids are used or stored This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they are supervised or have been given instruction concerning the use of the appliance by a person responsible for their safety Do not immerse in liquid or allow liquid to run into the interior of the appliance as this could create an electrical shock hazard When the appliance has been unpacked check it for transport damage and ensure all parts have been delivered If parts are missing or the appliance has been damaged contact the Goldair Customer Services Team If your appliance does not wor
Download Pdf Manuals
Related Search