Dealer`s Manual
Contents
1. USERS MUST NOT lean forward while sitting in the Raz Shower Chair as this may cause the chair to tip forward USERS MUST NOT wheel down a ramp without an attendant who gt l can hold onto the chair during the descent AN CASTER LOCKS ARE NOT BRAKES Never use caster locks to ry slow down the shower chair when descending inclines as this k V could cause the chair to tip in the direction of travel Lateral Stability USERS MUST NOT lean over the edge of a Raz Shower Chair as this could cause the chair to tip USERS MUST NOT attempt to pick up objects from the floor by leaning over and reaching a reacher or assistance from others should be employed USERS MUST NOT position the Raz Shower Chair on a side slope as this could cause it to tip Raz AT Dealer s Manual 2 20090122 Ramps and Other Inclines Ramps and other surfaces that are not level such as slopes into wheel in showers must be tested with an attendant to ensure that they don t compromise the chair s stability A qualified healthcare professional should be consulted to assist with this process DO NOT push or pull the Raz AT up or down an incline or ramp that exceeds a 1 12 grade 5 slope DO NOT allow any user to be propelled pushed or pulled in a Raz AT Shower Chair in any other manner than by an attendant ALWAYS CHECK THAT THE RAZ AT SHOWER CHAIR IS STABLE BEFORE IT IS OCCUPIED BY ANY USER AT ANY TIME Immersion The Raz Show2. Raz Rehab Shower Chairs AT Model Dealer s Manual A guide to help authorized Raz dealers safely set up and adjust Raz Rehab Shower Chairs 20090122 SAFETY PRECAUTIONS Failure to comply may cause injury or damage It is important that the Raz Rehab Shower Chair be properly assembled and that all adjustments be made carefully Please ensure that the user s and attendant s have read the User s Manual and thoroughly learn the safe operation of the Raz Shower Chair Up to date manuals are available online at www razdesigninc com For clarification of any section of this manual contact the Canadian distributor or the manufacturer IN CANADA IN THE U S A Dynamic Health Care Solutions Raz Design Inc Bolton Ontario Canada Toronto Ontario Canada 905 951 8541 866 875 2877 1 877 720 5678 info dynamichcs com info razdesigninc com CHAIR CLASSIFICATION BASED ON MAXIMUM USER WEIGHT AT 300 Ibs 136 kg SAFETY WARNINGS TO CONSIDER FOR RETAIL PURPOSES Forward Stability The front 5 casters on all models are equipped with dual locks The step on lever activates both the roll lock and the swivel lock It is essential that all casters on the shower chair be in the outward position before engaging the locks for optimal forward and lateral stability f so equipped disengage the optional directional caster lock first before rotating the rear caster to the rearward position and applying the casters dual locks
3. With this screw in place lift the armrest post to an upright position thereby allowing the second nut located in the insert track to slide down to the bottom of the armpad Insert another screw through the other hole on the post Slide the armrest up until the loose locknut in the track lines up with the screw Secure the screw loosely Slide the armpad to the desired position on the armrest post making sure that the position of the armpad does not impede the flip function of the armrest Tighten the screws fully and test the armrest prior to use Repeat steps 2 to 8 for the right armpad 13 20090122 2 11 Molded Arm Trough Installation Kit includes Molded Arm Troughs x2 10 32 flange locknuts x4 and 10 32x1 screws x4 Tools needed a Phillips screwdriver 1 Unscrew the 10 32x1 screws from the 10 32 flange locknuts in the metal insert on the bottom of the left arm trough 2 Push one screw up through the bottom and then the top of the hole farthest from the chair on the left armrest post 3 Position one of the nuts in the track on the arm trough insert over this screw and secure it loosely NOTE When positioned over the armrest post the left arm trough should be mounted so that the centre of the pad is located outside of the chair s perimeter Failure to do so may inhibit the flip function of the armrest 4 With this screw in place lift the armrest post to an upright position thereby allowing the
4. 2 8 Disconnect one lateral support pad from the L bracket on the mounting post by removing both sets of screws and locknuts Attach the extension plate behind the L bracket using the previously installed 4 20x screws and 4 20 thin locknuts With the additional screws provided in the kit connect the lateral support pad to the extension plate and secure it with the locknuts Repeat steps 1 to 3 if an extension plate was ordered for the other lateral support Leg Adductor Installation Kit includes for each side an adductor pad a mounting post frame clamp x2 a plastic tri lobe a mounting plate a two piece adductor clamp 20x hex head screw x2 74 20x1 hex head screw x2 4 20x1 hex head screw x2 2 washer x14 4 20 locknut x4 3 8 spacer x2 Tools needed a 7 16 wrench and an adjustable wrench 1 Loosen both outer 20x17 hex head screws on the mounting plates until the two clamps can fit around the horizontal tubes on the seat frame Ensure that the clamps latch onto the frame from above it not below Locate the adductor plate on one horizontal frame tube towards the front of the chair to a position near the footrest receivers that suits the users needs Secure the frame clamps in place by tightening the screws Attach an adductor pad to a mounting post by removing both washers and nuts on the pad insert tab Position the end of the moun
5. Molded Headrest Hand Grips Adjustable Tension Back Upholstery Trigger Locking Flip Up Armrest Molded Seat Commode Pan 7 Ce W H Strap Adjusta Back Seat Post Adjustable Adjustable Footrests Caster Dual Lock e Raz AT Dealer s Manual 6 20090122 2 Phillips Screwdriver 1 2 Raz Rehab Shower Chair AT Model Specifications SPECIFICATION RAZ AT Under Frame TILT FUNCTION Gas spring assisted up to 40 tilt range SEAT WIDTH 18 SEAT DEPTH 16 or 19 SEAT ADJUSTMENT Up to 2 fore aft SEAT HEIGHT front seat to floor 21 25 CLEARANCE HEIGHT Under Pan 12 16 17H 21 FIXED BACK Standard Fixed Height Flip Up Armrests 17 back height Z505 20 back height Z506 ADJUSTA BACK Optional Adj Ht Angle Flip Up Locking Armrests 20 back height Z515 17 back height Z510 24 back height Z520 ARMREST HEIGHT 8 Z505 9 Z506 7 9 Z510 8 101 Z515 8 10 Z520 WIDTH BETWEEN ARMPADS 18 LATERAL SUPPORT adjustment range 1 2 2 offset 2 vertical 1 fore aft 5 pad angle FOOTREST ADJUSTMENT from seat to footplate 16 2072 Z705 18 2277 Z707 CASTER TYPE AND SIZE Dual locking 5 casters x4 OVERALL WIDTH 22 WI std armpad 2572 w Z715 armpad OVERA
6. double D rings and a plastic buckle 1 Take both straps and both DD rings out of the accessory box 2 Weave the loose end of one strap through the DD ring and slide the DD ring several inches from the end 3 Feed the strap through the slot in the backrest mounting plate from the inside to the outside and then weave the loose end back through the DD ring 4 Repeat steps 2 and 3 for the other side of the strap 5 Adjust the DD ring and tighten the pelvic strap as needed 6 Pull tightly on each strap to ensure that they are secured properly prior to use Raz AT Dealer s Manual 20090122 14 214 H Strap Installation An H Strap can be attached to the footrests on any Raz model Kit includes a one piece H Strap with a Velcro closure 1 Remove the H Strap from the accessory box 2 With the Velcro facing towards the chair center the strap horizontally between both footrest hanger tubes and wrap the strap around the tubes until the loop Velcro engages with the hook Velcro 2 15 Heel Loop Installation Heel Loops can be attached to one or both footrests on any Raz Shower Chair they provide added support and comfort for the user especially when in a tilted position Kit includes Heel Loop x2 a 4 20x1 button head cap screw x2 a 4 20 thin locknut x2 and a 17 spacer x2 Tools needed 5 32 hex key 7 16 wrench and a drill with a bit 1 Remove the heel loop kit fr
7. Remove the screw from the frame tube and backrest mounting plate as shown 4 Remove the black cap from the back horizontal frame tube this cap may be discarded 5 Insert the tilt assist pedal into the tube as shown with the black friction strip facing up 6 Replace the screw through backrest mounting plate chair frame tube and tilt assist pedal post 7 Secure with the washer and locknut 8 Test the Tilt Assist Pedal to ensure proper installation TIP If the Tilt Assist Pedal fits loosely inside the frame tube remove the tilt assist pedal post and adhere one or both of the included plastic shims to either side of the horizontal pedal post Take care to not cover the hole on the post 2 7 Lateral Support Installation One or two Lateral Supports may be mounted on any Raz AT Model An extension plate can be ordered as an option to attain better positioning of the Lateral Support Pad 2 7 1 Lateral Support Installation on Adjusta Backs Kit includes for each side a mounting post one 3 8 16x2 button head cap screw a 3 8 16x1 button head cap screw a 3 8 washer x2 3 8 16 locknut x2 a 4 20x screw x2 a 1 washer x2 a lateral L bracket and a Lateral Support Pad Tools needed hex key 3 8 hex key and a 9 16 wrench 1 Remove the lateral sub assembly kit from the accessory box 2 Separate the left armrest assembly from the left armrest weldment on the back frame by unscrew
8. advised to ensure that an overall check of the fasteners and all components of the Raz Shower Chair be properly assessed by their dealer at least once per year Raz AT Dealer s Manual 20090122 15 3 0 ADJUSTMENTS IMPORTANT ADJUSTMENTS SHOULD NEVER BE ATTEMPTED WITH THE USER IN THE CHAIR 3 1 Backrest Adjustment 3 1 1 Backrest Angle Adjustment Tools needed 5 32 hex key and a 7 16 wrench 1 Loosen and remove the locknuts washers and coved spacers inside both vertical backrest frame tubes 2 Remove the middle 1 screws and washers from the vertical backrest frame tubes 3 Rotate the backrest to one of the 3 positions on the backrest mounting plates NOTE Select the middle hole for a 90 backrest angle rear hole for 85 or front hole for a 95 backrest angle 4 With the backrest in place insert the screws and washers through the selected holes on the backrest plates and then push them through the frame tubes 5 Fasten the other end of the screws with coved spacers washers and locknuts te 6 Tighten the assembly with a hex key and wrench until the end of the screw extends 1 or 2 threads beyond the nylon locknut Sw 3 1 2 Adjustable Tension Back Upholstery Adjustment In order to adjust the back upholstery of the backrest each strap can be tightened or loosened in the buckles to achieve a wide range of positions For example the second and third straps from the bottom can be
9. tightened to create more pronounced support in the lumbar area of the back The looser the straps of the back upholstery the more the fabric will sling in creating more contact with the user 3 2 Molded Seat Adjustment 3 2 1 Molded Seat Depth Adjustment The seat has approximately 2 of fore aft adjustment Tools needed 2 Phillips screwdriver T me 1 Release the seat by squeezing the spring clips that lock the d Be N front seat brackets to the chair frame U iy 2 Remove the seat by lifting up on the front edge and sliding the E seat forward and away from the chair Se Le 3 Loosen do not remove the eight screws attaching the front and rear seat brackets to the underside of the seat 4 Return the seat to the chair frame nestling the front seat clamps onto the front support tubes 5 Slide jiggle the seat to the desired position 6 Tighten the screws just enough to hold the front seat clamps in place making sure the seat is positioned evenly and square to p l g the frame i E 7 With the seat on the chair slide the rear brackets back until J they make firm contact with the rear crosstube tighten the screws to hold the brackets in place 8 Remove the seat steps 1 amp 2 and tighten all eight screws af d 9 Secure the seat to the chair frame by following the seat K installation steps in section 2 2 Raz AT Dealer s Manual 16 20090122 3 2 2 Molded Seat Height Adj
10. under the tube near the rear right wheel slide the directional caster lock up into place around the chair frame NOTE The directional caster lock latch must be facing towards the front of the chair to properly engage with the caster 4 Move the caster lock back along the frame towards the caster Check the position by engaging the directional caster lock and then the caster s dual lock The dual lock should be able to flip up without hitting the directional lock guide when it is in the downwards activated position 5 Replace the plastic spacer above the frame tube and between the two lock plates 6 Return and tighten the screws and locknuts 7 Test the directional caster lock for interference Raz AT Dealer s Manual 9 20090122 2 6 Tilt Assist Pedal Installation An optional Tilt Assist Pedal can be ordered to help attendants tilt the Raz AT Shower Chair The Tilt Assist Pedal can be mounted on either the left or right side of the chair depending on the attendant s preference Kit includes a Tilt Assist Pedal and two clear plastic shims Tools needed 5 32 hex key and a 7 16 wrench 1 Remove the tilt assist pedal from the accessory box 2 On the preferred side of the chair for the tilt assist pedal remove the locknut and washer from the bottom screw nearest to the back of the chair NOTE The Tilt Assist Pedal can be mounted on either the left or right side of the chair depending on the attendant s preference 3
11. 3 Tighten the screws fully and test the armrests prior to use 3 9 Molded Arm Trough Adjustment Tools needed a Phillips screwdriver 1 Loosen the 10 32x1 screws from the 10 32 flange locknuts in the metal insert on the bottom of the arm troughs 2 Slide the arm troughs to the desired position on the armrest posts making sure that the positions of the arm troughs do not impede the flip function of the armrests 3 Tighten the screws fully and test the armrests prior to use 3 10 Chest Positioning Strap Adjustment 1 Open the Velcro on the chest strap 2 Tighten or loosen the strap around the user as needed 3 11 Pelvic Positioning Strap Adjustment 1 Loosen both straps through the double D ring DD ring on one side of the pelvic strap 2 Adjust by pulling or pushing the outer end of strap in or out of the DD ring 3 Repeat step 2 for the other side of the strap 4 Pull tightly on each strap to ensure that it is secured properly 3 12 H Strap Adjustment 1 Disconnect the Velcro from the back of the H strap and adjust it to sling or tighten the H strap to suit the users needs 2 Press firmly on the Velcro to secure the strap prior to use Raz AT Dealer s Manual 19 20090122 4 0 USE AND OPERATION 4 1 Tilt Funtion The Raz AT Shower Commode tilts up to 40 to provide comfort and relieve pressure for the user Two gas assist springs facilitate this action and make the tilt smooth for the user and fac
12. Ensure that all knobs and screws are tightened securely for the user s safety 3 4 Armrest Adjustment Adjusta Back Option Only 3 4 1 Armrest Height Adjustment The armrests are adjustable in height within a 3 range in Je increments on the Adjusta Back Option only The armrests can be adjusted in height from 7 to 9 2 with the 17 Height Adjusta Back and from 8 to 10 with the 20 and 24 Height Adjusta Back Tools needed 3 16 hex key and a wrench 1 Loosen and remove the lower locknut 2 Loosen and remove the top locknut 3 Keeping the armrest and armrest pivot plate assembly together move the unit up or down on the armrest support weldment depending on the user s needs Replace the locknut onto the top screw Replace the locknut onto the bottom screw Tighten screws and locknuts at the top and bottom Repeat steps 1 to 6 for other armrest NOS Raz AT Dealer s Manual 17 20090122 3 4 2 Armrest Angle Adjustment The armrest angle can be adjusted up 5 or down 5 if the backrest angle is adjusted from the 90 factory position Tools needed 3 16 hex key and a wrench 1 Loosen and remove the screw washer and locknut on the bottom of the armrest pivot plate 2 Keeping the upper screw in place rotate the armrest assembly until the preferred position is reached by aligning one of the 3 holes arranged in a triangle on the armrest pivot plate with the holes on the
13. LL LENGTH WHEN UPRIGHT Without footrests 337A With footrests 43 OVERALL LENGTH WHEN TILTED Without footrests 4172 With footrests 5177 WEIGHT CAPACITY 300 Ibs PRODUCT WEIGHT 65 Ibs FRAME AND HARDWARE MATERIAL Stainless Steel Tools Required for Set up and Adjustments 1 1 8 Wrench 9 16 Wrench Raz AT Dealer s Manual 7 32 Hex Key 5 32 Hex Key 3 16 Hex Key Adjustable Wrench 1 4 Hex Key 3 8 Hex Key 7 16 Wrench 2 0 SET UP 2 1 Backrest Installation Tools needed 5 32 hex key and a 7 16 wrench 1 Remove the Shower Chair from the shipping carton 2 Lift the backrest to an upright position TIP A Phillips screwdriver can be inserted through one of the plates and back posts to temporarily fix the backrest in an upright position 3 Insert an included 1 long hex socket button head screw with a washer through one of the three holes on the backrest plate then push the screw through the backrest frame tube NOTE Select the middle hole for a 90 backrest angle rear hole for 85 or front hole for a 95 backrest angle 4 Attach to the other end of the screw a coved spacer washer and locknut as shown below 5 Tighten the assembly until the end of the screw extends 1 or 2 threads beyond the nylon locknut 6 Repeat steps 3 to 5 for other backrest plate WASHER TOP VIEW OF BACKREST ASSEMBLY i D LOCKNUT COVED SPACER 2 2 Molded Seat Ins
14. This feature is provided to facilitate the pushing of the chair by reducing unwanted sideways movement Close quarters manoeuvrability may be easier with the directional lock in the off upwards position To engage the directional lock first ensure the caster dual locks are not activated and that each caster can swivel and roll freely Pull the Raz AT rearward until the rear casters swivel to their forward positions directly under the frame tube Flip the directional lock guide latch down to its on position so that it cradles and holds the caster in the forward position If the caster is not perfectly in line with the frame the spring loaded latch once activated will engage if the rear caster is slowly swung around To disengage the directional lock flip the spring loaded latch up to its off position ALWAYS release the directional lock and swivel all four casters to their outward position for maximum stability before transferring or tilting a user Raz AT Dealer s Manual 20 20090122 4 4 Locking Armrests To flip up the locking armrests release the arm lock by lifting the trigger underneath the armrest tube and lift up the armrest This feature is included with the Adjusta Back Option only An optional locking armrest latch can be ordered to equip a fixed back with locking armrests 4 5 Lateral Supports The Raz Shower Chair may be fitted with optional lateral supports The lateral support pads lock in the forward p
15. Upholstery 1 Remove the plastic buckles and tri glides from the back upholstery straps paying attention to how the straps are wound through each component as they are removed 2 Remove the back upholstery from the back frame and machine wash with a mild detergent in warm water on a normal or gentle wash cycle Include other strap accessories such as the H strap pelvic and chest positioning straps 3 Install the back upholstery and other positioning accessories on the chair and allow to dry DO NOT dry the back upholstery in a clothes dryer or damage to the upholstery may occur 4 Assemble all plastic buckles and tri glides onto straps 5 Adjust the straps to the desired tension 5 2 2 Frame Armrests Adjustable Footrests and Other Components 1 Spray the frame and components with a multi purpose disinfectant cleaner scrub with a soft brush and rinse with water 2 If necessary spray the frame and components with a diluted 10 parts water to 1 part solution calcium lime remover scrub with a soft brush and rinse thoroughly with water DO NOT mix a calcium lime removal solution with any other liquid or toxic fumes may occur It is recommended to the user that a qualified Raz dealer check over all fasteners and subassemblies on a continuing basis or if there is cause for concern to the shower chair s performance It is highly recommended that any rinsing of Raz Shower Chair components occur in a well drained area with an industrial st
16. armrest support weldment 3 Replace the 3 8 x screw and 3 8 washer into the preferred position on the armrest pivot plate and finish with the locknut 4 Tighten the screw and locknut 5 Repeat steps 1 to 4 for the other armrest 3 5 Adjustable Footrest Adjustment 1 Remove a plastic snap pin from one footrest hanger tube 2 Adjust the footplate extension tube vertically to achieve the desired height in the footrest hanger tube 3 Insert the snap pin through the footrest hanger tube and the extension tube Ensure that the snap pin is completely through the tube and that the grey plastic clip is snapped securely around the outside of the hanger tube 4 Repeat steps 1 to 3 for the other footplate 3 6 Lateral Support Adjustment 3 6 1 Lateral Support Height Adjustment Tools needed hex key 3 8 hex key and a 9 16 wrench 1 Remove the lateral pad from the mounting post by removing the two screws and washers from the threaded holes on the mounting post 2 Remove the locknuts from the armrest assembly and leaving the armrest in the same location change the height of the lateral mounting post to the needed height NOTE An additional screw provided in the lateral sub assembly kit may be required depending on the required locations of the armrest and lateral pad The mounting post must always be anchored into the top hole on the armrest weldment on the chair 3 Replace and tighten the locknuts onto the armrest
17. assembly screws 3 6 2 Lateral Support Angle Adjustment Tools needed 5 32 hex key and a 7 16 wrench 1 Loosen each set of screws at the desired location for lateral support rotation and shift the brackets against one another 2 Tighten the screws once the position and angle is achieved 3 Verify that the lateral support can rotate 270 without hitting other components on the chair The armrests must be able to raise and lower without interference when the lateral support pad is in both the forward and rear positions Raz AT Dealer s Manual 20090122 18 3 7 Leg Adductor Adjustment Tools needed a 7 16 wrench and an adjustable wrench 1 Loosen do not remove both outer 4 20x1 hex head screws on the mounting plates relocate the adductor plate on the horizontal frame tube to a position that suits the users needs 2 Loosen the tri lobe knob and adjust the mounting post up or down to the desired height 3 Ensure that all knobs and screws are tightened securely prior to use 4 Repeat steps 1 to 3 if adjustments are required for a second leg adductor 3 8 Molded Flat Armpad Adjustment Tools needed a Phillips screwdriver 1 Loosen the 10 32x1 screws from the 10 32 flange locknuts_ in the metal insert on the bottom of the armpads 2 Slide the armpads to the desired position on the armrest posts making sure that the positions of the armpads do not impede the flip function of the armrests
18. e crossbar and tighten the hex head screws to secure the clamp 5 Insert the vertical swan neck support bar into the mounting clamp on the chair backrest crossbar with the tri lobe on the vertical bar facing up and towards the front of the chair as shown 6 Tighten the bottom tri lobe knob on the clamp securely 7 Insert the headrest post into the bracket on the vertical support and adjust the position to suit the users needs 8 Tighten the top tri lobe securely 2 4 Adjustable Footrest Installation includes Left and right footrests comprised of a footplate and extension tube connected to the hanger tube by a snap pin 1 Remove wrapped footrests from the inner accessory box 2 Lift the hanger tubes up from the footplates 3 With the footplates directed in place the footrest hanger tubes into the receiving sleeves at the front of the commode frame f the support tubes are directed forward the pins on the tubes will engage with grooves in the sleeves and lock in place Ki 2 5 Directional Caster Lock Installation A Directional Caster Lock can be added to one caster on the Raz AT Shower Chair to facilitate linear movement of the chair Kit includes a directional caster lock subassembly Tools needed 5 32 hex key and an adjustable wrench 1 Remove the directional caster lock from the accessory box 2 Remove the two loosened top screws locknuts and the plastic spacer between the lock plates 3 Starting
19. eam cleaner e g Intersteam or a commercial pressure washer Several times each year the shower chair and its components should be wiped down with a diluted calcium lime removal solution to reduce deposits followed by a hot water rinse To reduce the risk of mildew buildup the entire chair should be wiped down with a soft dry cloth after the final rinse and before storage or use 5 3 Suggested Cleaning Products Task Recommended Products General Cleaning Antibacterial Detergent Tuberculocidal Surface Cleaner and Accel TB Virox Technologies Inc SepteFX Intermediate Level Disinfectant 7D 11 Titan Worldwide Inc Calcium and Lime Deterrent CLR Outdoor Furniture Cleaner Raz AT Dealer s Manual 22 20090122 IMPORTANT DO NOT USE ABRASIVE SCRUBBING POWDERS OR SCOURING PADS ON THE RAZ SHOWER CHAIR DO NOT SUBMERGE THE RAZ SHOWER CHAIR IN WATER RINSE THOUROUGHLY AFTER CLEANING TO ENSURE THAT ANY SOAP OR DETERGENT RESIDUE IS REMOVED DO NOT USE CLEANING PRODUCTS WITHOUT CONSULTING THE PRODUCTS INSTRUCTIONS AND TAKING APPROPRIATE PRECAUTIONS FOR HUMAN EXPOSURE TO CHEMICALS 6 0 CONTACTS It is important that the Raz Rehab Shower Chair be properly assembled and all adjustments be made carefully Up to date manuals can be downloaded from www razdesigninc com For clarification of any section of this manual contact the Canadian distributor or manufacturer IN CANADA IN THE U S A Dynamic Hea
20. eee 7 1 3 Tools Required for Set up and Adjustments sss eee eee eee 7 SET UP 2 1 Backrest Installation ii a e a ae aE ee a h EAFA E a eta ERE 8 2 2 Molded Seat Installation s ee sese eee 8 2 3 Molded Headrest installation sese 9 2 4 Adjustable Footrest installations sese eee eee 9 2 5 Directional Caster Lock EE EE 9 2 6 Tilt Assist Pedal Joelle sdegeaceedeg degt Seege gege eege ee 10 2 7 Lateral Support Installation see ee eee 10 2 7 1 Lateral Support Installation on Adiusta Backes sese 10 2 7 2 Lateral Support Installation on Fixed Backes eee 11 2 7 3 Extension Plate Installation sete oti teeta EE ee 12 2 8 LEO Addu ctor IM StallAUG EE 12 2 9 Armrest Lock Telle 13 2 10 Molded Flat Armpad Installaton 13 2 11 Molded Arm Trough Installation AAA 14 2 12 Chest Positioning Strap Installaton seer ee 14 2 12 Pelvic Positioning Strap Installation EE 14 RE Ne Dee INStallation DEE 15 2 15 Heel Loop Installation iscciscc cae ccdicecds cue ive ceased AER ANERER ee dee 15 2 16 Fastener installation eee 15 ADJUSTMENTS Sol BaGktest AdU nT 1 EE EE 16 3 1 1 Backrest Angle e Enn EE 16 3 1 2 Adjustable Tension Back Upholstery Adiustment sse sese eee 16 3 2 Molded Seat Adiustrmeritisssecassccicinech acts atencebecesvons eege Dee 16 3 2 1 Molded Seat Depth Adiustmment AA 16 3 2 2 Molded Seat Height Adiustment AA 17 3 3 Molded Headrest Adjustment sees 17 3 4 Armrest Adjustment Adjusta Back Option Only sse eee eee eee 17 3 4 1 Armrest Height Adju
21. er Chair is not designed to be used as a pool chair Do not immerse the shower chair in whole or in part in water or any other liquid Damage to the shower chair components may result Transfers The most dangerous part of using any shower chair is the transfer Since every chair has different stability characteristics it is essential to carefully review and test the transfer technique to ensure that the procedure is safe Test transfers should be performed with an attendant who can prevent the chair from tipping or moving during the transfer If you feel that the transfers cannot be repeatedly performed safely contact a healthcare professional who is familiar with transfer techniques and options Individuals who have not learned proper transfer skills must seek assistance during transfers and may require the use of a mechanical lift Transferring onto a Raz AT Shower Chair ALWAYS lock all four casters in their outward position front casters positioned in the forward position rear casters positioned to the rear for maximum chair stability Caster locks DO NOT and CANNOT prevent the casters from sliding and the shower chair from moving if the floor is slippery A slippery floor can be caused by dust water soap or any substance that does not allow the casters to grip the floor securely Transfers should never be attempted with the shower chair positioned on slippery surfaces It is recommended that transfers be performed on clean dry
22. ilitated for the attendant To tilt the chair the attendant must squeeze both tilt triggers and move the chair into the desired angle To lock the chair in place the triggers are simply released Directly after purchase the triggers and springs may seem stiff This stiffness is normal and diminishes with use Some attendants have a need for a tilt assist pedal which enables the attendant to place one foot on the lever to facilitate tilting j The tilt function must only take place when the casters are locked _ NOTE When the chair is mounted at the lowest height setting the maximum potential tilt angle is 40 The higher the chair is set the fewer degrees the chair can be tilted back With a seat to floor height of 25 the chair can be tilted back 36 IMPORTANT ANY ATTENDANT MUST BE FAMILIAR WITH PROPER TILTING TECHNIQUES PRIOR TO ASSISTING A USER IN THE SHOWER COMMODE A PELVIC STRAP IS RECOMMENDED FOR ANY USER AS AN EXTRA SAFETY PRECAUTION 4 2 Casters Each Raz Shower Chair caster is equipped with a dual lock feature which stops the caster from swivelling and rolling simultaneously To activate the dual lock step on the end of the caster brake lever until it latches in the on position To deactivate the dual lock step on the raised end of the dual lock until it latches in the off position 4 3 Directional Caster Lock The flip down Directional Caster Lock keeps one rear caster aligned in a forward direction
23. ing both button head cap screws 3 Replace the screws with longer screws from the lateral sub assembly kit A 3 8 16x2 screw should be inserted in the arm pivot position and the 3 8 16x1 screw in one of the three anchor positions 4 Replace the armrest assembly against the armrest weldment at the desired height The new screws should protrude more from the armrest weldment than the previous ones 5 Position the left mounting post on the inside of the left armrest weldment Make sure that the orientation of the mounting post is such that the tab with the holes is up and facing forward on the outside of the chair as shown Raz AT Dealer s Manual 20090122 Two screws 10 10 Kit includes for each side a mounting post 3 8 16x2 button head If the desired armrest height is high enough both screws from the armrest assembly may be used to secure the lateral mounting post to the chair with the locknuts provided In the case that the armrest assembly is mounted low on the armrest weldment the pivot plate can be secured at the bottom with the screw from the armrest assembly and the mounting post should be anchored to the weldment with the 3 8 16x174 screw from the lateral kit as high on the armrest weldment as possible Secure the mounting post at the desired height with the 3 8 washers and 3 8 16 locknuts provided in the lateral support kit Take the left lateral support pad assembly w
24. ith the blue arrow decal pointing up and out and connect it to the outside of the lateral mounting post by securing two 4 20x screws and La washers into the threaded holes on the mounting post Secure all fasteners and verify that the lateral support can rotate 270 without hitting other components on the chair The D5 armrest must be able to raise and lower without interference SC wS when the lateral support pad is in both the forward and rear positions Repeat steps 2 to 9 for the right lateral support if required 2 7 2 Lateral Support Installation on Fixed Backs cap screw a 3 8 16x1 button head cap screw 3 8 washers x8 3 8 16 locknuts x2 4 20x screws x4 20 locknuts x2 y washers x6 a fixed back lateral adapter plate a lateral L bracket and a Lateral Support Pad Tools needed hex key 3 8 hex key and a 9 16 wrench 1 2 3 10 11 Remove the lateral sub assembly kit from the accessory box Separate all of the hardware from the fixed back lateral adapter plate Unscrew and remove the left armrest pivot button head cap screw Leaving the armrest and spacers in position on the chair install the 3 8 16x2 screw and a 3 8 washer included in the lateral kit into the left armrest pivot position Insert an included 3 8 16x1 screw and a washer into the hole on the armrest weldment which lies directly below the armrest pivot scre
25. lth Care Solutions Raz Design Inc Bolton Ontario Canada Toronto Ontario Canada 905 951 8541 866 875 2877 1 877 720 5678 info dynamichcs com info razdesigninc com Raz AT Dealer s Manual 23 20090122
26. n positioned over the armrest post the left armpad should be mounted so that the centre of the pad is located outside of the chair s perimeter Failure to do so may inhibit the flip function of the armrest 4 8 9 Raz AT Dealers Manual Take a 5 16 18x screw and insert a 5 16 washer onto it Insert the screw and washer into the hole in an armrest fin Install the right armrest latch spring 90 bend end into the 90 bend end small hole on the armrest support fin with the 90 bend facing towards the front of the armrest slide the spring opening over the screw on the inside of the armrest fin as shown Hook end Stretch the spring hook clockwise and install the latch plate over the screw and spring with the stop facing towards the outside of the arm Release the spring and the hook section will rest on the upper edge of the armrest latch Secure the assembly with a 5 16 18 locknut Tighten the locknut only until the screw threads penetrate the nylon in the locknut Do not over tighten as the spring mechanism will not rotate freely Repeat steps 2 to 7 for the left armrest K E A 5 Unscrew the 10 32x1 screws from the 10 32 flange locknuts in the metal insert on the bottom of the left armpad Push one screw up through the bottom and then the top of the hole farthest from the chair on the left armrest post Position one of the nuts in the track on the armpad insert over this screw and secure it loosely
27. non slippery surfaces A fully carpeted surface is optimal Be aware that area rugs and shower mats can slide on floors and thereby present a hazardous surface DO NOT stand on any part of the frame of the Raz AT Shower Chair NEVER use the footplates to assist in transfers This could cause the chair to tip The footrests should be swung to the side or removed entirely during transfers to provide unobstructed access to the shower chair Raz AT Dealer s Manual 20090122 Tilt Function ALWAYS check the tilt function and ensure both locking gas springs and release cable assemblies are fully operational BEFORE the chair is occupied by the user ALWAYS use a pelvic strap as an additional safeguard for the user in a tilted position A pelvic support strap may be ordered as an option with the Raz AT DO NOT attempt to tilt an occupant if the attendant is physically incapable of safely and smoothly operating the tilt function NEVER leave the user unattended in a tilted position in a Raz AT Shower Chair The Raz AT Shower Chair is NOT intended for use as a transportation device or a long term seating system IMPORTANT USERS SHOULD NEVER BE LEFT UNATTENDED IN A RAZ AT SHOWER CHAIR Raz AT Dealer s Manual 4 20090122 1 0 2 0 3 0 DEALER S MANUAL TABLE OF CONTENTS Page GENERAL INFORMATION 1 1 Raz Rehab Shower Chair AT Model Overview sese eee 6 1 2 Raz Rehab Shower Chair AT Model Specifications sss eee eee
28. om the accessory box 2 Remove the left footrest from the chair if already installed Take note of the edge of the footplate that is located the closest to the chair when installed 3 Turn the left footrest upside down to expose the underside of the footplate 4 Locate the pilot hole furthest away from the footrest hanger tube on the edge of the footplate that will be closest to the chair once mounted Selection of the proper pilot hole is very important prior to drilling 5 Drill through the footplate using a drill with a 4 drill bit using the pilot hole on the underside of the footplate as a guide 6 Slide the large opening of one heel loop over the footrest hanger tube until it sits against the footplate It is more comfortable for the user if the cut edges of the strap are facing towards the chair away from the user s feet 7 Slide a plastic spacer onto a 20x1 button head cap screw and insert the bolt and spacer in through the top of the small slot of the strap and into the new hole in the footplate 8 Secure the screw and strap in place with a 20 thin locknut on the underside of the footplate using a hex key and wrench 9 Repeat steps 2 to 8 for the right heel loop if required 2 16 Fastener Installation All fasteners should be installed securely to ensure that they are snug and do not pose any risks to the end user Locknuts that are removed for any reason should be replaced rather than re used The user is
29. osition and in the rearward position behind the backrest To release a lateral support pad from either position grip the pad assembly at the blue arrow decal and lift straight up Once released rotate the lateral pad to the forward or rearward position and press lightly at the decal area to lock the pad in place Check to ensure the lateral is locked in place before use Lateral supports are designed to assist in maintaining an upright posture in the Raz Shower Chair Adjustments up down medial lateral should be made by the dealer so that the pads are positioned safely Raz AT Dealer s Manual 20090122 21 5 0 CLEANING AND MAINTENANCE 5 1 Cleaning After Each Use 5 1 1 Commode Pan 1 Remove the commode pan and empty contents 2 Wash the pan with a multi purpose disinfectant cleaning solution Use a scrub brush if needed 3 Rinse well before storage or re use NOTE A soapy hot water wash followed by a disinfectant spray can be substituted for a multi purpose disinfectant cleaning solution 5 1 2 Molded Seat 1 Spray with a multi purpose disinfectant cleaner and scrub with a soft brush as required 2 Rinse with a water spray before storage or re use DO NOT IMMERSE the seat in water or cleaning solutions 3 Fora more thorough cleaning remove the seat from the shower chair to allow better access to the underside of the seat and around the opening of the seat 5 2 Cleaning As Needed 5 2 1 Adjustable Tension Back
30. second nut located in the insert track to slide down to the bottom of the arm trough 5 Insert a second screw through the remaining hole on the armrest post 6 Slide the arm trough up until the loose locknut in the track on the arm trough insert lines up with the screw Secure this screw loosely 7 Slide the arm trough to the desired position on the armrest post making sure that the position of the arm trough does not impede the flip function of the armrest 8 Tighten the screws fully and test the arm trough prior to use 9 Repeat steps 2 to 8 for the right arm trough 2 12 Chest Positioning Strap Installation A one piece Chest Positioning Strap can be attached to any Raz Model The back upholstery includes loops intended as strap guides Kit includes a one piece chest positioning strap with a Velcro closure 1 Remove the chest strap from the accessory box 2 Insert one side of the strap through both loops sewn into the back upholstery on the shower commode chair 3 With the user seated in the chair thread one end of the strap through the D ring on the other end of the chest strap 4 Secure the strap in front of the user with the Velcro closure 2 13 Pelvic Positioning Strap Installation A two piece Pelvic Positioning Strap can be ordered with the shower chair and can be attached to any Raz Model This installation should be performed with care as the user s safety is dependent on secure straps Kit includes two straps with
31. stment 2 0 cceeeeeccssecceee eee eeeeedeeceeeeceteeeeescceaeeeeneeeees 17 3 4 2 Armrest Angle Adjustment 0 0 ccceseeceseecseeeneeeeneeeseecceeeneeeeeneseneceeenaeeenes 18 3 5 Adjustable Footrest Adjustment sse eee ee eee 18 3 6 Lateral Support AdIuSment sss eee eee ee eee 18 3 6 1 Lateral Support Height AdIuStment see eee eee eee 18 3 6 2 Lateral Support Angle Adjustment 2 c ccccceeeeeeseeceenceeeeeneeesneceeseneteeeees 18 3 7 Leg ee Meel EE 19 3 8 Molded Flat Armpad Adiustment AAA 19 3 9 Molded Arm Trough Adiustment E 19 3 10 Chest Positioning Strap Adhusiment sse eee eee eee 19 3 11 Pelvic Positioning Strap AdiIuSstrment sese 19 3 12 EE Ee Be TEE 19 Raz AT Dealer s Manual 20090122 4 0 USE AND OPERATION Avi WiIMGFUNCUOM EE 20 AD EE 20 4 3 Directional Caster Locke 20 AA LOCKING ArMreStS eeteeierieedeki dee enge EKOS Ee ed ions EN TAANE E ienest 21 d Lateral SUPPOMMS ETH S 21 5 0 CLEANING AND MAINTENANCE 5 1 Cleaning After EE 22 5A Commode lt 1 iieii AE ENEE e ER Bee EER 22 CL Molded Seat seneta EES E EE aa EE 22 5 2 Cleaning As Needed iengkier k opekdgeg erbei Zeien pies ENEE SES danka eieiei ieste ER 5 2 1 Adjustable Tension Back Uobolsien sees 22 5 2 2 Frame Armrests Adjustable Footrests and Other Components 22 5 3 Suggested Cleaning Bee ler EE ER Et CONTAC TS EE eeh ER 1 0 GENERAL INFORMATION 1 1 Raz Rehab Shower Chair AT Model Overview
32. tallation 1 Ensure that the spring clips in the front seat brackets are in the unlatched position To unlatch the spring clips squeeze each clip inward to unlatch the free end from the front seat bracket 2 Slide the rear of the seat over the rear crosstubes as the front of the seat is lowered onto the frame Check to make sure that the rear seat brackets hook below the crosstubes 3 Continue lowering the front of the seat until the front seat brackets nestle onto the front seat support tubes 4 Secure the seat in place by latching the spring clips To latch the spring clips squeeze each clip inward while moving the free end towards the seat until the spring clips click into the seat brackets around the front support tubes 5 Reverse steps 1 to 4 to remove the seat from the frame Raz AT Dealer s Manual 8 20090122 2 3 Molded Headrest Installation Kit includes Molded Headrest and post a vertical swan neck support a two piece headrest mounting clamp a plastic tri lobe x2 a 4 20x17 hex head screw x2 a washer x2 and a 4 20 thin locknut x2 Tools needed an adjustable wrench 1 Remove the headrest mounting clamp and vertical support from the accessory box 2 Remove the 20 locknuts from the back of the black clamp 3 Install the clamp on the rear crossbar by pushing the screws with washers through the holes in the clamp and crossbar 4 Replace the washers and nuts on the inside of th
33. ting post against the adductor pad insert tab and align the holes Secure the pad to the post by fastening the 4 20x hex head screws with the two sets of washers and locknuts Loosen the tri lobe knob at the clamp Insert the mounting post into the receiver clamp on the outside of the mounting plate now located on the chair frame Tighten the tri lobe knob when the adductor pad is located at the desired height for the user Repeat steps 3 to 8 for the other side of the chair if required Tighten all hardware securely and test the Leg Adductors before use Raz AT Dealer s Manual 20090122 12 2 9 Armrest Lock Installation Locking armrests are pre installed on a shower chair ordered with the Adjusta Back option In the case that a Fixed Back standard is requested in the order flip up armrests are standard and an optional locking armrest kit must be ordered and installed by the dealer To maintain the integrity of the fasteners this operation is best performed without removing the installed flip up armrests Kit includes two latch plates left amp right springs 5 16 18x 4 button head cap screw x2 5 16 washer x2 5 16 18 locknut x2 Tools needed 3 16 hex key and an adjustable wrench f 2 3 Se 2 10 Molded Flat Armpad Installation Kit includes flat armpads x2 10 32 flange locknuts x4 and 10 32x13 screws x4 Tools needed a Phillips screwdriver 18 2 3 NOTE Whe
34. ustment To change the seat to floor height on a Raz AT model the chair is raised from the wheel base at the seat posts on both sides of the chair Tools needed 1 4 hex key and an adjustable wrench Remove screws from the left and right seat posts on the chair Remove the screws from both gas springs under the seat Lift the chair to the height required for the user Adjust the seat to a position level to the ground Return the screws to their positions in the seat posts and gas springs on the chair Note The screw on the gas spring will need to be relocated from its previous position in order to achieve a level seat APwoON gt IMPORTANT INCREASING THE SEAT HEIGHT AND INCREASING THE BACKREST ANGLE WILL DECREASE REARWARD STABILITY IT IS ESSENTIAL THAT A STABILITY CHECK BE PERFORMED AFTER ANY OF THESE ADJUSTMENTS ARE MADE 3 3 Molded Headrest Adjustment Adjusta Back Option Only Tools needed 5 32 hex key 1 Loosen the bottom tri lobe knob and adjust the vertical swan neck support in order to achieve headrest height adjustment 2 Loosen the top tri lobe knob and adjust the headrest post horizontally for a fore aft change in position 3 To change the angle of the headrest itself loosen do not remove the three screws on the back of the molded headrest Rotate the headrest around the end of the headrest mounting post to suit users needs and tighten the screws to secure the desired position 4
35. w Mount the fixed back lateral adapter plate in the orientation shown onto the two installed screws on the inside of the armrest weldment Secure both screws with a 3 8 washer and 3 8 16 locknut Insert two remaining 20x screws with washers into the exposed holes on the fixed back lateral adapter plate and install the mounting post on these screws Make sure that the orientation of the mounting post is such that the tab with the holes is up and facing forward on the outside of the chair Secure the mounting post at the desired height with Ai washers and o 20 locknuts provided Take the left lateral support pad assembly with the blue arrow decal pointing up and out and connect it to the outside of the lateral mounting post by screwing two 20x screws and 2 washers into the threaded holes on the mounting post Secure all of the fasteners and verify that the lateral support Raz AT Dealer s Manual 11 20090122 can rotate 270 without hitting other components on the chair The armrests must be able to raise and lower without interference when the lateral support pad is in both the forward and rear positions 12 Repeat steps 2 to 11 for the right lateral support if required 2 7 3 Extension Plate Installation Kit includes for each side a lateral support extension plate Ya 20x a screw x2 20 thin locknut x2 Tools needed 5 32 hex key and a 7 16 wrench 1 2 3
Download Pdf Manuals
Related Search