Home

Christie CP2000-SB User Manual

1. Figure 2 6 Connect Ballast RS 232 and Interlocks to Projection Head e BALLAST INTERLOCK CABLE Connect the ballast s interlock cable 34 002007 to Panel C 9 pin routing through the small rectangu lar access hole in the rear underside of the projection head Figure 2 6 Ensure a second connector from Panel C to Panel B is connected P N 001 100376 01 The remaining third connector is a non functional spare CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 2 5 Section 1 Introduction CHY IS TIE i f POWER CABLES TO HEAD From behind the main AC breaker panel within the pedestal connect both identical power cables 34 001992 to the IEC receptacles located near Panel B 100 230 VAC and Panel C 200 230 VAC Con nect either cable to either receptacle these cables are interchangeable and secure with metal strain relief clip provided Figure 2 7 To Rear Receptacle To Front Receptacle NOTE Connect either cable to either receptacle Figure 2 7 Connect Projector Breaker Power Cables to Projection Head Important Components in the lamp compartment will require 200 230 VAC NOTE f you prefer to use an uninterruptible power supply UPS for supplying power to the projection head route the UPS power cables through the pedestal toe and connect to the IEC receptacles on Panel B 100 230 VAC In this case only one power cable provided in the pedestal is used g CHEC
2. ILS Motor Control Board Main Code CRC Upgrade MCB software 3 5 4 TPC Custom Menu NOTE Password protected Requires Advanced Admin or Installer rights The TPC s five Custom menus enable installers service administrators or advanced users to tailor projector processing as they wish for any type of incoming source including 3D material and collect these settings into a unique channel that any user can select at the Main menu Up to 32 channels can be defined SAVING OR DELETING Changes in the Custom menu are saved when you leave the menu Or to delete one or more channels use the trash bin Delete button note a caution dialog box will appear first Custom Page 1 and Page 2 These two menus consist of numerous display settings that can be adjusted as desired then defined collectively as a custom setup or channel Each defined channel then appears as a button on the Main menu where any user can select it providing a reliable way to quickly and correctly change the on screen display to suit the source content Alternatively if a pre defined Projector Configuration File PCF has been supplied with distributed content rare and the Use PCF checkbox checked those Custom options which are already defined in the PCF Source Target Color Color Space Gamma and LUT CLUT disappear from the Custom menus and are protected from further modification The channel defined in such a case will thus be based on 1 the display
3. If AC between terminals 2 and 3 is 207 265 connect terminal 2 to T2 factory default If AC between terminals 2 and 3 is T 180 207 connect terminal 2 to T1 Y See Figure 2 21 Igniter Jumper between 2andTi BALLAST 115 VAC TAPS 1 s2 2 3 4 6 G Ensure your nominal line between the D terminals labeled 115V and COMMON SS J or OV is within 10 of 115 VAC See Figure 2 22 Figure 2 21 Check Voltage and Position Jumper If your measurement at the 115V ter minal is 126 5V or more move the 115V wires to the tap labeled 10 If your measurement at the 115V terminal is 103 5V or less move the 115V wires to the tap labeled 10 Voltmeter Caa If AC 103 6 126 4 S Use 115V tap If AC 126 5 or more If AC 103 5 or less Use 10 tap Use 10 tap Ballast 10 10 oV 115V lololele AAN g Figure 2 22 Check Voltage Between 115V and Common 0V CP2000 SB User Manual 2 15 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 2 2 2 16 Installing and Connecting Sources Depending on site requirements cinema servers such as digital media storage devices or non cinema sources such as PCs either reside outside of the projector or are rack
4. or setting a precise power level for the lamp Current Channel Toggle LiteLOC function ON OFF Set and maintain Display of current lamp Apply LiteLOC settings to the settings automatically current channel only checked updated read only main atus Custom Advanced ja Reading from light sensor consistent light output ve 4 as indicated in the Set EEAS Light Output sensor light level window Lamp power range adjustable from 75 to 110 if LiteLOC is not in use or as temporary override reading read only Figure 3 13 Custom Lamp Menu Options Table 3 7 Summary of Custom Lamp Menu Options CUSTOM LAMP MENU OPTIONS Lamp Power Lamp Per Channel When enabled LiteLOC setting is applied to the specified channel When disabled all channels will use the global LiteLOC setting Enable Maintains a chosen light level at the screen over time the lamp ballast will gradually increase power to the lamp as necessary until it reaches the maximum level possible for the installed lamp To disable LiteLOC temporarily or permanently clear the LiteLOC Enable checkbox or adjust Lamp Power directly Indicates what percentage of power appropriate for the installed lamp to supply to the lamp auto matically overriding any LiteLOC setting that may be in effect This causes the bar graph to rise or fall but the LiteLOC line and set value will not change
5. Check with theatre personnel for the degree of screen tilt or measure this incline with a protractor at the screen Then TILT the projector to closely match this screen tilt angle Figure 2 29 following the instructions below adjust t height 1 Disconnect the projector from AC power 2 Usea wrench to rotate front and rear feet until projector tilt matches screen tilt You can achieve S up to 12 tilt by adjusting the feet Y Figure 2 29 Adjust 4 Feet for Tilt and Leveling CP2000 SB User Manual 2 19 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE In rare cases where additional tilt is needed you can utilize the rear extender legs as described below Important For best optical performance avoid tilting the projector excessively Use vertical offset of the lens instead 3 Remove the rear bottom panel 2 top screws 2 bottom tabs from the CP pedestal Figure 2 30 Qualified Service Technician Only Remove rear cover e Elevate proj with car jack Figure 2 30 Open Rear of Pedestal 4 Use a low profile scissor jack to elevate the rear of the projector 5 On each side of the rear opening in the pedestal loosen the 2 bolts securing the rear extender legs to the projector Figure 2 31 Loosen leg bolts and adjust legs Secure leg bolts Figure 2 31 Adjust Rear Extender Legs 6 Slide the legs out to the desired position and secure with tw
6. A D Macro Formatter Board a k a Formatter Interface Board Processor Board Diagnostics Performed DSP FPGA Load FPGA Code Valid FPGA Initialize FPGA McBSP XRDY FPGA Done FPGA Register Read Write Serial ID Chip CLUT SRAM Overlay Framestore SDRAM Resizer FIR Chip Resizer FIFO CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 3 15 Section 1 Introduction CHY IS TIE i Other System Supervisor Module Detected Not Detected Self Test OK Failed Ballast Communications OK Failed Can also be set to trigger a full screen flashing red alarm window on the TPC Note that ifa DMD temperature exceeds a certain factory set threshold for at least 2 seconds the lamp will automatically shut down Recovery requires that the DMD temperature fall to a safe factory set threshold Safety interlock 3 5 3 TPC Alarm Window 3 16 Identifies the new alarm e Unexpected Lamp Off condition Interlock System has detected an open interlock Extractor Fan Open Blinking Red New Alarm Condition Select to shunt disable this alarm e Condition will persist until rectified but will not trigger another alarm window e Acknowledgements are discarded upon on next TPC power up alarm window will re appear Figure 3 7 Flashing Alarm Window In addition to the status bar at the bottom of any TPC screen a full s
7. Intake air flows through the filter before circulating in the front compartment to cool the main electronics Replace the air filter whenever the lamp is replaced or sooner in dusty dirty environments Check condition monthly Refer to Section 6 4 Replacing the Lamp amp Filter for complete instructions Breaker Panel Each circuit breaker on the pedestal serves two purposes 1 it is a power switch for one or more components and 2 it protects against over current conditions All breakers must be ON for normal CP2000 SB power up and operation enabling AC to reach the CP components If faulty or excessive AC is detected a breaker will trip to OFF in order to prevent damage to the relevant component Try moving the breaker ON again if the breaker continues to trip OFF the AC problem must be resolved Breakers are e MAIN AC 3 phase Turns the CP lamp ballast liquid cooling system Ethernet hub and TPC ON OFF The 3 switches move in tandem e PROJECTOR Turns the CP projection head electronics only anot the lamp ON OFF e INTERNAL single phase Turns on off any extra equipment such as an extractor fan mounted within the exhaust duct that has been plugged into a power bar connected to CP s terminal block TB2 Functional only with 5 wire or 6 wire AC supplies NOTE Called AUX on CP2000 SB models for connection of Cine IPMs NOTE Breakers do not ignite the lamp You must use the TPC Lamp Button Casters The 4 l
8. 65535 01002 ERR 002 System Warning 8032 00001 SSM Read Failed CP2000 SB User Manual B 17 020 100162 06 Rev 1 03 2014 Section 1 Introduction B 2 2 For Your Information FYI FYI messages are generated and broadcast when an overall change in the projector s status is detected Each FYI message identifies the IP address of the TPC generating the message followed by a code for the change as well as one or more parameters of descriptive details about what has changed NOTES 1 Because FYI messages are gated by the Error Message Enable EME control disabling serial error message also disables FYI messages 2 FYI messages do not occur unless there is a Cine IPM present B 2 3 History HIS CHRISTIE A number of lamp histories are stored in memory with the oldest discarded when there is no more room An accurate lamp history requires that the serial for a new lamp be recorded when the lamp is installed HIS message parameters are e P1 Lamp order oldest lamp installed 001 next oldest 002 etc e P2 of hours logged e P3 Lamp serial e P4 strikes e P5 Installation date amp time e P6 Lamp type e P7 Status Failed to Strike e P8 Status Failed Restrike e P9 Status Unexpected Offs e P10 Life State e P11 Change Reason B 2 4 Intelligent Lens System ILS B 18 P1 0 Installed 1 Lens Reset on Startup 2 Auto ILS 3 Lens Calibrate 4 Lens Reset P2 0 No 1
9. To widen a squeezed image into a scope 2 39 1 theatre display swing the 1 25x anamorphic or 1 26x wide converter lens into place in front of the primary zoom lens of the projector This lens increases magnification across the width only regaining the original proportions in the image and is often used in theatres where side masking can be moved aside CP2000 SB User Manual 3 65 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH ISTIE i 3 10 Working with 3D A single projector can display 3D images as described below Such images require a 3D capable source as well as additional hardware and cabling in order to be displayed and interpreted correctly in a typical stereo 3D viewing environment 3 10 1 3D Description In simple terms images generated from a 3D cinema source consist of a series of images frames or fields that alternate quickly between two slightly different viewpoints corresponding to the physical separation of our left and right eyes called parallax When these frames are displayed with enough speed and viewed with special glasses synchronized with the left right L R frame sequencing the resulting single perceived image appears with much the same depth and perspective we sense in the real world The new full resolution triple flash hardware Brilliant3D includes an FPGA Formatter Interface Board FFIB which allows for full 2K resolution using a 6 2 frame rate multiplication Triple Flash Triple Flash 3D i
10. 03 2014 CHRISTIE Section 1 Introduction Examples of Critical System Error 001 Messages 65535 01002 ERR 001 System Error 0008 00001 Fan Intake 1 65535 01002 ERR 001 System Error 000A 00001 Fan Card Cage 65535 01002 ERR 001 System Error 0021 00001 Lamp Failed to Ignite Table B 4 P3 Codes for 002 System Warning Error Messages Component Code P3 Component 8010 Prism Temperature Warning 8011 Temperature DMD Red 8012 Temperature DMD Blue 8013 Temperature Integrator 8014 Temperature SSM 8015 Temperature Card Cage 8016 Temperature Ballast 8020 Lamp Life Expired 8021 Lamp Failed to Ignite 8032 SSM Read Failed 8033 SSM Flash Write Attempted 8034 Motor Calibrate Failed NOTE System Warning messages can elevate to System Error messages if the problem is not fixed In these cases the 8 in the original System Warning code will change to a 0 see Table B 3 Table B 5 P4 Codes INCLUDED WITH SYSTEM WARNING ERROR MESSAGES ONLY Examples P4 Meaning 1500 or lower Fan speed is 1500 RPM Speed must be 1501 RPM or higher 056 always C Temperature is 56 Cool to within ranges shown in Table 3 1 00001 There is no P4 data for this type of error Examples of System Warning 002 Error Messages 65535 01002 ERR 002 System Warning 8010 00051 Prism Temperature Warning 65535 01002 ERR 002 System Warning 8020 00001 Lamp Life Expired
11. 1 03 2014 CHRISTIE 2 Installation amp Setup This section explains how to install connect and optimize the projector for delivery of superior image quality NOTE The illustrations provided are to enhance the understanding of the written material They are graphical representations only and may not represent your exact projector model 2 1 Assembly and Connection of Components e 2 2 Installing and Connecting Sources e 2 3 Connecting for Communications e 2 4 Adjusting Tilt and Leveling 2 5 Initial Power Up e 2 6 Maximizing Light Output e 2 7 Basic Image Alignment e 2 8 Offset and Boresight Alignment 2 9 Fold Mirror and Convergence Adjustments CP2000 SB User Manual 2 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE 2 1 Assembly and Connection of Components 2 1 1 2 2 These instructions describe how to mount the projection head onto the pedestal position the projector relative to the port window and screen connect pedestal to head cabling and cooling hoses customize projector for CP2000 SB lamps connect exhaust ducting and fill liquid cooling system ns and lamp connect to power A WARNING 1 DO NOT misplace High Security keys which are packed with the projector Replacement involves dispatching a field technician to the site at owner s expense 2 Quali fied technician required for all installation steps Do not modify circuits or wiring Before You Begin You will req
12. America Japan 16 A 400 VAC Europe Asia Power consumption max 8 8 kW all regions Current rating continuous of 3 phase AC input at breaker 40 A N America Japan 40 A Europe Asia Ballast Start up voltage 135 175 VDC Operating voltage range 18 46 VDC Operating current range 50 180A Max ripple 1 max 25 C Internal Convenience AC Qty amp type of AC connector receptacle 1 terminal block N America Japan 1 terminal block Europe Asia Maximum wire gauge for terminal blk 8 AWG Nominal voltage dependent on voltage connected to unit 100 120 N America Japan 208 240 Europe Asia No of phases any region 1 Line frequency any region 50 Hz 60 Hz nominal Power available max 1320 W fe America Japan 1500 W Europe Asia Current available any region 10A 8 6 Lamps CXL CDXL Lamps kW Current Range amps Average life Hours CXL CDXL 20 2 0 CXL CDXL 30 3 0 CXL CDXL 45 4 5 CXL CDXL 60 6 0 CDXL 60SD 6 0 95 155 105 165 1000 105 170 CXL 20 requires adaptor kit P N 003 001728 xx NOTE Current range shown includes over drive which is 10 more than the original lamp rating CP2000 SB User Manual 8 5 020 100162 06 Rev 1 03 2014 Section 1 Introduction 8 7 8 6 CHRISTIE Table 8 1 Minimum and Maximum Lamp Power by Lamp Type Lamp
13. CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHKISTIE Section 1 Introduction DATA The value for a given projector parameter such as ON or OFF appears in ASCII decimal format directly after the request reply symbol Unless you add an optional space after the symbol i e before the data in a set message data immediately follows the request reply symbol without a space Other details about data All values returned by the projector reply messages have a fixed length of either 3 or 5 characters regardless of the actual value the value is padded with leading zeros as needed e Data in set messages does not require padding e For any given parameter data length is always the same E g the picture mute value which is either on 1 or off 0 is always 3 digits 001 or 000 e Within one message multiple parameters of data must be separated by one space character e Data pertaining to a specific source other than the current source is preceded by the letter S the source number i e channel and a space This is similar to an extra parameter P0 e Text parameters such as channel names are enclosed in double quotes following the data as in Name TEXT PARAMETERS Most data is simply a numerical value however some messages also require text For example a channel naming message typically includes a text based name after the channel number enclose this text in double quotation marks as in Tilt the Wagon Use all char
14. Enables disables SNMP configuration 192 j200 200 50 Figure 3 33 Choosing SNMP from Admin IP Config Menu CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction Table 3 18 Summary of Admin IP Config Menu Options ADMIN IP CONFIG MENU OPTIONS DLP vs TPC vs SNMP Select which device address you wish to see or set DLP projector TPC Touch Panel Controller SNMP The Internet standard protocol developed to manage nodes servers workstations routers switches and hubs etc on an IP network SNMP enables network administrators to manage net work performance find and solve network problems and plan for network growth Change Config Host Name Enter a checkmark to edit the Ethernet Configuration text boxes defining the device s address Enter a name for the projector optional Obtain address from DHCP Allow the projector s IP address to be auto assigned by your network s DHCP server NOTE Cur rently not supported Specify a Static IP Address Enter the full valid and unique address supplied by the network administrator for using the device at this site IP Address When DLP or TPC is selected The first three octets of the IP address identify the network to which the device belongs the last octet identifies the specific device i e the projector or the TPC Keep in mind that if you change the node any of the first 3 octets the device will then belong
15. Lamp menu indicate that the lamp power has reached this over drive state either reduce your LiteLOC setting or install a new lamp TPC If the TPC fails to initialize re boot the projector and try again A failed TPC usually indicates a system failure requiring service A TPC communication failure crash while displaying a test pattern requires that the projector be cycled OFF and ON again If the TPC response becomes sluggish try re booting the projector If it persists the installer may have set the TPC Data Logging option to Detailed which taxes memory and performance For best results and normal operation this setting should be reduced to Errors or Standard Erratic TPC behavior or an error message such as Could not write to file can also indicate an internal memory shortage Make sure to regularly delete back up files or corrupt files from the IPSM and or CompactFlash memory card Save backups to a PC laptop only not the TPC contact your administra tor If the locations of button presses on the screen seem to be misinterpreted the TPC screen may need recalibrating CP2000 SB User Manual 7 3 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH ISTIE i 7 4 Ethernet 1 Ifthe TPC stalls at Waiting to Connect you have 30 seconds in which to enter a service login Make sure the Ethernet settings are valid for your site all devices should have the same subnet mask but unique IP addresses 2 Make sure to save
16. Over time as the theatre screen ages and dust and dirt collects on the port window the theatre may no longer be achieving the expected footlamberts as reported by the TPC It is a good idea to periodically recalibrate footlamberts refer back to Figure 3 36 CP2000 SB User Manual 3 63 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 3 9 3 9 1 3 64 Working with the Lens The CP2000 SB lens mount secures the primary zoom A TERR lens to the projection head It provides 1 setup l Motorized m adjustments for correct boresight and 2 automatically BE Vertical Offset controlled focus zoom and offsets for general use To save the focus offset and zoom settings to the channel Vv Anchor you must make the adjustments using the motorized lens aint 7 a oresi mount adjustment features in the Main Lens menu or Aig Custom Lens menu from the TPC Using the knobs on the lens mount to adjust each position does not save the zontal settings to the channel They are designed for temporary Knob use and will therefore be lost once the channel changes NOTE After any manual adjustment click Lens Reset in the Advanced Lens menu to ensure ILS settings are Motoried Horizontal properly recalled orizontal ee An optional auxiliary lens 1 25x or 1 26x can be lt gt installed into an optional auxiliary lens mount then Boresidht swung into place in front of the primary len
17. Projector Hours 8 Shutter O Off 1 On 20 Lamp Current 21 Lamp Voltage 22 Lamp Power 23 Approximate foot lamberts If Pl 2 0 Signal Status O OK 2 invalid Good or bad signal Signal Information 1 Channel Current channel 101 132 2 Vertical Frequency Current vertical frequency 3 Test Pattern O Off gt 0 On If Pl 3 2 Lamp Error 0 OK 1 Unexpected lamp Operation Status OFF 2 Lamp failed to ignite 10 Card cage temperature C Shows caution or critical 11 Blue DMD temperature C Shows caution or critical 12 Red DMD temperature C Shows caution or critical 13 Integrator temperature C Shows caution or critical 14 Prism temperature C Shows caution or critical 15 SSM temperature C Shows caution or critical 16 ILS temperature C Shows caution or critical 20 Lamp vane switch interlock 0 OK open 21 Extractor vane switch interlock 0 OK open 22 Lamp door interlock 0 OK 1 open 23 Auxiliary interlock High current 0 OK 1 open 24 Tamper switch 0 OK open 30 Intake fan 1 rear speed RPM Also indicates slow or 31 Intake fan 2 front speed failed condition 32 Card cage fan speed 33 LAD fan speed i 40 SmpteATotalErr 41 SmpteARecentErr 42 SmpteBTotalErr 43 SmpteBRecentErr 50 SecurityInstalled 51 SecurityArmed 52 Security Tamper 53 CompLidOpen 54 NonCompLidOpen 55 CommFailure 56 BatteryL
18. The luminance brightness which results from one foot candle of illumination falling on a perfectly diffuse surface 1 fL 3 423 candela per square meter cd m For example the SMPTE RP 98 calls for theatre screen luminance of 12 to 22 fL 16 2 fL 55 7 cd m is the open gate target according to SMPTE 196M For cinema applications xenon lamp wattage is approximated to achieve this level using 12 W ft2 x screen height squared or 5 W fi of total scope image area for matte screens and typical lenses FRAME RATE The frequency at which complete images are generated For non interlaced signals the frame rate is identical to the vertical frequency For interlaced signals the frame rate also known as field rate is one half of vertical frequency GAIN OR SCREEN GAIN The ability of a screen to direct incident light to an audience A flat matte white wall has a gain of approximately 1 Screens with gain less than 1 attenuate incident light screens with gain more than 1 direct more incident light to the audience but have a narrow viewing angle For example An image reflecting off a 10 gain screen appears 10 times brighter than it would if reflected off a matte white wall Curved screens usually have larger gain than flat screens A 6 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction GVG Grass Valley Group formerly part of Tektronix More specifically the gvg file format used for com
19. e amp 3 Inputs 8 4 Touch Panel Controller e 8 5 Power Specifications e 8 6 Lamps e 8 7 Regulatory e 8 8 Environment 8 9 Weight amp Size 8 10 Standard Components CP2000 SB User Manual 8 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction 8 1 Display CHRISTIE Panel Resolution Pixel format H x V on 3 DMDs 2048 x 1080 Contrast Ratio and Refresh Rate 2D Refresh rate DLP Cinema processing 23 97 48 Hz SMPTE 292M 2D Refresh rate Non cinema processing 23 97 85 Hz VESA DVI 3D Refresh rate 24 Hz per eye 144 Hz max Pixel Clock rate 150 MHz max Achievable Requires maximum output conditions 14 fL on 25m 75 ft screen Brightness Achievable 2000 1 full on off Colors and Gray Displayable colors 35 2 trillion Scale Gray scale resolution 15 bits each per RGB component 45 total linear White Point Nominal white x 0 314 0 002 full white after calibration in telecine mode y 0 351 0 002 Gamma 2 6 nominal 8 2 Lenses Primary Zoom Lenses High Contrast Max of Image Below or Above Lens Center 1 25 1 45 1 38 809079 5 1 100 vertical 70 horizontal 1 45 1 8 1 38 809061 51 100 vertical 70 horizontal 1 8 2 4 1 38 809052 51 100 vertical 70 horizontal 2 2 3 0 1 38 809053 51 100 vertical 70 horizontal 3 0 4 3 1 38 809069 5 1 100 vertical 70 horizontal
20. ultraviolet exposure and high temperatures generated by the lamp and associated circuits are authorized to assemble install the projector and perform service functions inside product enclosures Typographical Notations The following notations are used throughout this manual Keypad commands and PC keystrokes appear in bold small caps such as POWER INPUT ENTER etc References to specific areas of the document appear italicized and underlined When viewed online the text appears in blue indicating a direct link to that section For example Section 8 Specifications References to other documents appear italicized and bold such as Christie Service Manual References to software menus and available options appear bold such as Main Menu Preferences e User input or messages that appear on screen in status display units or other control modules appear in Courier font For example No Signal Present Login christiedigital Error codes LED status appear in bold e g LP Al etc e Operational states of modules appear capitalized such as power ON power OFF Signal words such as Warning Caution and Notes are used in this manual to point the reader to specific information or instructions that warn of safety related hazards which may be present and indicates how to avoid them CP2000 SB User Manual 1 5 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE 1 6 CP2000 SB User Manual 020 100162 06 Rev
21. 1 of at the lens and Preference Lamp History Lens Test Pattern User 6 Reset Lamp Power or LiteLOC if desired ct Figure 3 50 Adjusting Using a Light Meter CP2000 SB User Manual 3 61 020 100162 06 Rev 1 03 2014 Section 1 Introduction 3 8 5 Stand by Mode Close the douser shutter to put the projector in a cooler stand by mode where lamp power is reduced to 50 of its maximum rating Upon opening the douser and restoring the image the lamp power will return to its previous setting 3 8 6 How Old is My Lamp When a new lamp is installed and its serial number recorded Advanced Lamp menu the lamp CHRISTIE Status Custom Advanced A 1998x1080 Flat xYZ 50 lamp power when closed 1998x1080 A 2048x858 Flat P3 Scope P3 Bp Reserved A Reserved Pd PCF Flat PCF Scope Za 1920x1038 VA 1920x804 Flat P3 Scope P3 _cH1 8 cHo 16 fcHas azJiensJ E Figure 3 51 Lamp Power in Stand by Mode timer resets to 0 and begins logging time for the new lamp This total appears in both the Advanced Lamp menu and the Status menu See right The Status menu also shows Total Lamp Hours which is the accumulated time logged for all lamps installed thus far Each past lamp log also appears in the Advanced Lamp History menu Main status Custom Advanced E E o rce i Projector Input 292 Dual i Signal V 23 74H2 AY Cine IPM 2K Not Detected a Environment o
22. 2 frames per image Increase the display frame rate as necessary to reduce flicker from your source s These N M ratios define how many frames to display per number of frames that form I complete image For all 3D use the bottom value is 2 indicating that two frames left and right are combined into every complete display frame For non 3D it is frame Set to the highest rate possible without image cropping CP2000 SB User Manual 3 23 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE NOTE Not for 2048 x 1080 ZF Z MT HT i M ull 24 Hz 24 Hz 24 Hz i 24 Hz i G i f I i y I I y y ET A Ri R2 oie R1 R2 te A 48 Hz 48 Hz 48 Hz 4 frames 2 sources 5 frames 2 sources 6 frames 2 sources 48 Hz x 2 48 Hz x 2 5 48 Hz x 3 ORR GETAR PMPA 96 Hz 1 20 ae See 144 i a Figure 3 12 Examples of pane Rate N M For example when processing typical dual L R 3D signals of 24Hz a Frame Rate N M setting of 4 2 will generate 4 frames of output for every 2 frames of input at a final frame rate of 96 Hz For any source keep the final frame rate less than that of the projector which is 67 Hz for full 2048 x 1080 resolution Generally incoming
23. 2048 x 1080 1920 x 1080 23 77 Hz Non cinema 1920 x 1080 2048 x 1080 23 48 Hz Cinema 2048 x 1080 2048 x 1080 23 72 Hz Non cinema 2048 x 1080 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 5 1 1 NOTES 1 Sources with can be VESA E EDID reported 2 Interlaced signals are not supported 3 The desired processing path for a DVI source is selected in the TPC Advanced Custom menu Non cinema processing is required for DVI sources with a pixel clock rate over 110 MHz which is the limit for cinema processing Keep in mind that the projector will attempt to automatically adapt to any incoming data format that is within the bandwidth or frame rate of the system thus formats beyond those shown in Table 5 1 may also be compatible Dual and Twin Link DVI Although dual link and twin link input options appear in the TPC Custom menu using the pair of DVI ports for a dual link signal that is two data streams and one clock via one dual link cable requires an adapter that accepts the dual link DVI connector Using the ports for a twin link signal two data streams with their own clocks each on their own single link cable requires a source that can provide this unique type of DVI output Either of the proposed configurations would increase DVI bandwidth DUAL LINK DVI TWIN LINK DVI NOTE One shared clock 165 MHz max NOTE 2 separate clocks 165 MHz max DVI 2 i i DVI q So E i dual link ca
24. 6 Maximizing Light CHUL missni sen eE E E RE EEN EERE EERE 2 22 2 6 1 Calibrating Screen Brightness fL ssesesessessesessssessesessseessessrssressessesseessteseestesseeseesenssresne 2 22 2 7 Basic Image Al Otte int ccsitasxeisasecncasceupnsosanavncstnn coxGenanriaey siwraxwunssanhuoran eneeaatPaaeisenrexnngeorkctiacrecurtes 2 23 2 7 1 Basic Optical Alignment Procedure ccs svacsavsnctrcdeplucnsiindacetomatusaiolainniamna ine 2 23 2 8 Offset and Bor sight AU OT SI sisstin in Ea ias 2 24 28 Adjust Offset naseer R E E OERE RRE 2 24 2 8 2 Adj st Left Right Boresig Wb aesscsenesdensexudtninscvuessoadustennsinedgnasyuahanaiiamniadadoie tanslandexattainectunaene 2 25 2 8 3 Adjust Top Bottom Boresight cccccccssccesscsesceescecsseceeceeeeesscecsaeceseeseeeeeseecsaeceeeseeeenaeees 2 27 2 8 4 Copy the Channel Settings To Another Channel essssnsseseesseessesssseesseesesessseeseeserssesse 2 27 2 8 5 Add Auxiliary Lens sce sansien caste taiceesaarru an coievn seen titas ita xosn tasan ten carinaunanacanca tonceseahin erin 2 28 A amorphio 125X Jarene E E E E E EERE E E R i 2 28 Wide Converter LEnS 120X sax caniasarasursonmsacanevunsnaseoncnennaniedecsubpanunseiveenaseameousseaesdedxutievastaxetes 2 28 2 9 Fold Mirror and Convergence Adjustments ccccceccessccsssecsseceeeceseeeeseecsaeceseceeeeeeseecsaecneeeaees 2 29 Fold Mirror Adjustment sses encanto uene ee 2 29 DMD OS sesser are eE EAN EE EEE E EE REEE 2 29 CP2000 SB
25. 69 C waming gt 70 C critical DMD Blue 60 64 C warning gt 65 C critical DMD Red 60 64 C warming gt 65 C critical Integrator 95 104 C warning gt 105 C critical Prism 70 74 C waming gt 75 C critical SSM 55 59 C waming gt 60 C critical Fan Speed RPMs of 4 internal cooling fans Fan 1 Intake 1 Fan 2 Intake 2 RPMs of 15t primary fan exhaust side of proj RPMs of 2 4 primary fan exhaust side of proj Card cage RPMs of electronics card cage fan LAD RPMs of laminar airflow device for DMDs SECURITY ENCLOSURE NOTE f any of the following indicators are red service is needed Security Enclosure Installed Security Enclosure Armed Security Tamper Component Side Lid Open Non Component Side Lid Open Enclosure Communication Failure Security Enclosure Battery Low CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction BUILT IN SELF TEST NOTE fany of the following indicators are red service may be needed General System Power up Self Test Security Lock Integrity Pc Interface Board Diagnostics Performed ARM FPGA Load FPGA Code Valid FPGA Initialize FPGA No Load Jumper FPGA Done FPGA Register Read Write UART 0 UART 1 Pc Ethernet Synchronous Serial Port File System GPI Macro
26. 7 Troubleshooting and if the problem persists contact your network administrator CP2000 SB User Manual 3 9 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE 3 5 3 10 Using the Touch Panel Controller TPC Touch Panel Controller software resembles other Windows based applications but is activated by touching the TPC screen itself Touch large raised rectangular buttons to activate a function such as turning the lamp or shutter ON or OFF or to start a presentation or select a different icon Buttons may include text and or an icon To log ON OFF as a different user touch the user icon in the bottom right comer To go to a new menu touch its tab at the top of the page To go to a submenu touch its tab located above the status bar To see more options in pull down menus touch Ly To select an option in a list touch the option text To begin entering text such as serial numbers touch the entry box To escape without change from a pull down list touch menu background Leaving a menu automatically saves its current settings Touch checkboxes to toggle on or off Touch 0 jump to the Status menu at any time All TPC menus and functions are illustrated and explained below NOTES 1 Shown are SAMPLE menus only your specific text and or icons may vary according to settings recorded in the password protected menus By default the Main menu offers 32 pre configured channels 2 If ne
27. 96 ILS Communications Error 97 ILS Sensor Failure 98 ILS In Bootloader 99 ILS CRC failure on main code CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHKISTIE Section 1 Introduction Function Code Examples Description and Parameters Focus FCS requires v2 9 or higher FCS 860 Used to adjust the focus under motor control FCS 860 1 FCS 860 1 1 Write P1 Location P2 Approach direction NOTE Approach is optional 1 Positive to Negative Approach 1 Negative to Position Approach Read P1 Real time position P2 Current direction P3 Moving Status 0 not moving 1 moving Related commands are Intelligent Lens System ILS Lens Horizontal Offset LHO Lens Vertical Offset LVO and Zoom ZOM For Your Information FYI FYI A change in projector status generally broadcast from TPC proj to all clients See Messages With Multiple Parameters in this Appendix Gamma GAM GAM gamma2 6 The filename representing the current gamma For example gammaz2 6 is typically used in theatres Gamma files name and content are all currently pre defined Also known as look up tables CP2000 SB User Manual B 5 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHAKISTIE Function Code Examples Description and Parameters GPIO Assignments GIO requires v2 7 or higher GIO 13 LampOff Allows macros to
28. ET 6 6 Gleaming th LenS sss cacaceaiccedado access us cexsampadeccseaie axcudnssanasnanccounbicacasunacenedeaemnaeasseteeteiees 6 6 CICA INS the Reflector arerioei eia eA rea aE E EE REEE denn RET E E TEER SE 6 6 6 3 3 Other COTO MEMES seie enori EEE E E A E E RRR 6 7 LAMP FAM EEEE EE E 6 7 DSA DOEN ah ENE TE E E EE AE S E A A 6 7 AIr FOW Tee OC eS zasrerieeneien er erinra a tee 6 7 Laminar Airflow Device LAD scccsssacseacessavecssvnaseascdonsenadsinassavesnndextuseastecsuvatssasveassueesestesioreass 6 7 OA Replaci g the Lamp amp Pater xg scceeectnccanvcsoacsnsssiccevataceuntaiatecdanishecensssasssbarseeasealaiedanmaieauppianceaalians 6 7 6 4 1 Lamp Replacement ProcedUtegimiesnissostirr iiine EE E EREK 6 8 6 4 2 Filter Replacement PEOCCUUIRe sxcssicscecisnssvaccsedssasensshovadsapasncednskandens dinaoesepheneasssssdeasiabatssaniaaes 6 11 6 3 Replacing a Leng isase a E E a E 6 12 7 Troubleshooting Tal POWE cies enc cine ae tae AE EEEE ec sia EEEE e EE Ra eE as 7 2 T1 Pr j ctor Will Not SCAG ersinnen nrennen in a a E EE i 7 2 FZ EATING E EE E I EE E E 7 2 7 2 1 Lamp Does Not PTI acs casixe saice ees ecian er cnotraicsunna teacenicadceneeatanncuncaaxeucentcaeastareneesedmneenuiceeenates 7 2 T 2 2 Lamp Suddenly Goes Off asieran pecan eae ace E RER RE 7 2 7 2 3 No Lamp Current REACIO 1 ncn sacesecvsadesaavncsvsedacsusnaciuasczeshacenaneaiee sentsansnetensadsesnbatenameracesats 7 2 7 2 4 Flicker Shadows or Dimes ccccccccscscccecessesss
29. ETA ECEE fall overdrive maximum and the power to it automatically levels off At this point the Preference Lamp Lamp History Lens Test Pattern User LiteLOC function terminates i e the power level stabilizes the lamp will begin Figure 3 47 LiteLOC Expiry sample to dim normally with age and the light output gauge will begin falling Either reduce your LiteLOC setting or replace the lamp Using Lamp Power To change to a different power level simply enter a new Lamp Power percentage at any time This will override and temporarily disable any LiteLOC setting that may be in effect 1 Set Lamp Power to apply a specific percentage of power appropriate for the installed lamp LiteLOC will automatically be disabled 2 Brightness will change accordingly new values will appear for amps volts and watts and the blue light output bar graph will move above or below the LiteLOC line depending on the new setting As the lamp ages and becomes more inefficient your chosen power level will gradually produce less and less light output To return to the previous LiteLOC setting enable the LiteLOC checkbox NOTE When re enabling LiteLOC from a current brightness level that is more than 10 brighter or dimmer than the LiteLOC setting the recovery will be immediate When re enabling LiteLOC from a brightness setting that differs by only 10 or less the recovery will be gradual Adjust LiteL
30. M in Mnre n AEE ERE E REE R 3 11 39 2 TPO Status MoU sscentdscciiesuatupasenaennaeesexawnudiuwilnaedeiviususunncdesstsunscduniinsenadionsesasuasesdeavwcsdacetioess 3 12 3 3 9 TPC Alatm Waa iscssccssdeaiccpivianccansctacnsoissacenesteesaraiaiecantannccsosssancasdapaeassdashecameiaarseaaes 3 16 Can Alarm Conditions Be Ignored x s asscecacezeucececysnadeaserlccaviniedaseanmaadmnaciednelacauied 3 16 Responding to an Alarm Window ccccccceesceessecsseceseeeeeeeeseecsaeceaeeseeeeeaeecsaeceseeeeeeenseessaeen 3 17 39 4 TPC Custom Men en viaccess nctenacisadecceanateiacentaaudsduades A A 3 18 Custom Pas eal MEM reiissi n E a E e 3 19 C stom Page Menu siini oeenn ee EE EE EE EEE E RARES 3 21 Gustom 3D Control MENU ssiseises santrine re eN aE E EE E E N EER E 3 22 Custom Lamp Men gee ne ee rn ence eee ae er RERET AER REEE ti 3 25 MUMS Ure Ee Menu seiersen E rama ok cadence aun eee eee 3 26 Channel Lens Menu DIS ab leds 4 cacacsceusiesntaseneaessvnndessacensnuecaseatbetonesunedosenssaccnmansensneeuewrs 3 27 3 5 5 TPC Advanced Mit issii erriei E EEE E E AR EEES 3 27 Advanced Preference Men s5s2 iscnsaserevhedii avmadvunssnadsiosspeanishasiwondtwtenpscsunionanicashateents 3 28 ii CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Table of Contents Advanced Lamp Menu scceek ce ec vcesreeaniesastebscdnntios cose aacesuaesigtasane a itni sasies cons sietst aten CrS Eunoa Saa 3 29 Adding New Lamp snesscsnononsnensian
31. P1 Lens type Valid lens 1 25 AN or 1 25WC P2 Lens serial number Lens Horizontal Offset LHO requires v2 9 or higher LHO 1023 Adjusts the horizontal offset of the output lens under motor control LHO 1023 1 LHO 1023 1 0 Write P1 Location P2 Approach direction NOTE Approach is optional 1 Positive to Negative Approach 1 Negative to Position Approach Read P1 Real time position P2 Current direction P3 Moving Status 0 not moving 1 moving Related commands are Intelligent Lens System ILS Lens Vertical Offset LVO Focus FCS and Zoom ZOM CP2000 SB User Manual B 9 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHRISTIE Function Code Examples Description and Parameters Lens Primary LNP requires v2 7 or higher LNA 1 25AN 1234567 P1 Lens type P2 Lens serial number Valid Lens 1 25 1 45HC 1 45 1 8HC 1 8 2 4HC 2 2 3 0HC 3 0 4 3HC 4 3 6 0HC 5 5 8 5HC 1 25 1 45HB 1 45 1 8HB 1 8 2 4HB 2 2 3 0HB 3 0 4 3HB A 3 6 0HB 5 5 8 5HB Lens Vertical Offset LVO requires v2 9 or higher LVO 264 Adjusts the vertical offset of the output lens under motor control LVO 264 1 LVO 264 1 0 Write P1 Location P2 Approach direction NOTE Approach is optional 1 Positive to Negative Approach 1 Negative to Position App
32. Source Selection Depending on your installation you may be able to select a source via communication from a different controller Regardless of how the display file is selected the feature will appear on screen according to the specific display settings recorded in that file If the screen display does not appear as expected this indicates that the display setup is incorrectly configured for the incoming source Try a different display file If the image is still incorrect the display setup may first have to be re configured with new settings Contact the trained operator responsible for updating display setups 3 5 10 Errors and Alarms Encountering the following conditions will always trigger a flashing red alarm window at the TPC e ACTIVATED SAFETY INTERLOCK caused by an open lamp door a failed extractor or lamp fan or an open fire alarm switch For any safety interlock breach the lamp ballast will immediately stop power ing the lamp e TAMPER DETECTION caused by unlocking the projector lid Failure is also logged and prevents dis play of incoming CineLink 2 encrypted cinema source material e FAILED LAMP IGNITION Failure to successfully strike the lamp e COMMUNICATION ERRORS SSM and or IC links may be malfunctioning It is also recommended that the following additional conditions always be set to trigger an alarm window default Select these triggers in the Advanced Preferences TPC menu e OVER TEMPERATURE caused when the
33. Source Settings ADMIN SOURCE SETTINGS INCOMING RESOLUTION ORIGINAL ASPECT RATIO 1998 x 1080 1 85 flat 2048 x 858 2 39 scope 1998 x 1080 1 85 flat 2048 x 858 2 39 scope Reserved PCF Flat flat Reserved PCF Scope scope 1920 x 1038 1 85 flat 1920 x 804 2 39 scope 1920 x 1038 1 85 flat cont d 1920 x 818 2 35 scope Alternate Content 1 Auto square pixels 1920 x 1080 2 39 scope Alternate Content 2 Auto square pixels 1920 x 800 2 40 scope 3D Flat Auto square pixels 3D Scope Auto square pixels CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 3 37 Section 1 Introduction Admin Screen Menu CHRISTIE The Screen menu defines 1 what portion of the projector s display panel you wish to use and 2 what cropping is needed to disguise possible keystoning or other geometric aberrations Once saved a screen file can be used with any incoming source as desired screen data is not included in a PCF and is independent of Source settings Consider screen files as convenient compensations for physical limitations in the environment You will typically need one or two screen files per site Define display area Save settings in a screen file for access in Custom menu Source screen Gamut 1P confi General J Lamp J P10 P Figure 3 26 Admin Screen Menu Options Enter a check mark to see ALL data Anamorphic needed Adjust to define
34. Source file settings as well as Screen file settings See also Admin Screen menu Man Status Custom J advanced Admn fiszo e Incoming Format Amount to discard value will discard data from top and or left value will discard from bottom and right Save settings in a source file for access in Custom menu CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 Create Source Restore Tet 7 Figure 3 24 Admin Source Menu Options Screen J Gamut 1H Config General Lamp J P10 7 Width to height image proportion desired Adjust x y resolution and off set as desired Test in display without saving Cancel new unsaved source settings 3 35 Section 1 Introduction CHY IS TIE 3 36 Table 3 14 Admin Source Menu Options ADMIN SOURCE MENU OPTIONS Resolution Activate then record the x y resolution of your incoming signal such as 2048 x and 1080 y or 1920 x and 1080 y Note that resolution must match the incoming signal format assuming you want to display all of it and may differ from the original resolution that you want to recover See Resolution Notes below Offset Activate then record how much incoming data you wish to discard essentially delaying the starting point for processing Leave at 0 to process all available data See Offset Notes below Aspect Ratio Enter the aspect ratio of the original cinema format you are trying
35. Type Min Lamp Power Max Lamp Power Other 16 1200W 75 1760W 110 Other 20 1500W 75 2200W 110 CXL 20 1500W 75 2200W 110 CDXL 20 1000W 50 2200W 110 Other 30 2000W 67 3300W 110 CXL 30 1000W 33 3300W 110 CDXL 30 2000W 67 3300W 110 CDXL 30SD 2000W 67 3300W 110 Other 45 3375W 75 4950W 110 CXL 45 1500W 33 4950W 110 CDXL 45 2300W 51 4950W 110 Other 60 4500W 75 6600W 110 CXL 60 2000W 33 6600W 110 CDXL 60 2750W 46 6600W 110 CDXL 60SD 2750W 46 6600W 110 Type Xenolite Stand by lamp power level for 4 6 kW Stand by lamp power level for 2 3 kW Motorized adjustment of position Recommended screen widths 2 0 kW 45 ft nominal 3 0 kW 55 ft nominal 4 5 kW 65 ft nominal 6 0 kW 75 ft nominal 50 of lamp s maximum current rating 75 of lamp s maximum current rating 3 axis 0 25 range for each Regulatory Audible Noise 70 dBA maximum NOTE Does not include customer supplied external extractor fan Safety e UL 60950 1 and CAN CSA C22 2 No 60950 1 03 1st edition bi national e IEC 60950 1 2001 EMC Emissions e FCC CFR47 Part 15 Subpart B Class A Unintentional Radiation e CISPR 22 2003 A1 2004 EN55022 1998 A2 2003 Class A Information Technology Equipment EMC Immunity CISPR 24 1997 EN55024 1998 A1 2001 A2 2003 EMC Requirements Information Technology Equipment CP2000 SB User Manual 020 100162 06 Rev 1 03 20
36. User Manual i 020 100162 06 Rev 1 03 2014 Table of Contents CHY IS TIE 2 9 1 Calibrating the System Using DCP Librarian Setup Software 00 0 ceceseeseeneeeteeeeeeeeenes 2 30 Color Ca Fall sssaaa E E E ete ean aoe 2 30 Electronic Screen Masking suse aexcesieadeecantnwkeihandeuesaenveneisiarvnsuneadaeet enteeeinsntencisearonneennincaniades 2 30 PCES R te sosch aac nasehanea assented seneesanstacisaiannasaasnsedemientesaceaceraxaantanesiaadesiaumdseaninaonsmamiasmamnieh 2 30 3 Operation 3 1 Projector FS ASICS cas soaicinss salocasdestercdnigecoudbaacasanataaseelercdei aceon ccesn cadence eae paece ene 3 2 3 1 1 Components and Features fncccaspceiaica tenasceatbecancasencusstaciee sin tuxeutantextinicncereasentacencetexesenteieeaies 3 2 Air Filter oseere e RAEE E EE Serdadsantuntese bRaciatad tenance satan E 3 3 Breaker Panel sviccssistanatsenwuptsuerionseniasnesrsasnnndevecuusesitaxenssnentutsenudiansesasuiseiataianuieneumenssuseentdswoniiecn 3 3 CASTETS E E E E 3 3 Communications and Source Connection Panel csssccssscesssssosssnesensncesccetacssecensnesees 3 3 Coolant Level Gage so cas ca ace coc erena Esae ke REES EE AA EEEE ESEE EREE SEEE Ae E EAER EARE RESELE SAES ECERS 3 4 Exh ust Duct RP ne aea E R E ere R 3 4 Extender Legs semoene o EE E E E ERE E E E E N 3 4 Lamps srisochsssnsdvepusaadainckatwnaaleiataaideasshad bisanasaceiihandaiaassduss a EE ER RRA 3 4 Lens Mount amp Auxiliary Lens Mount sessvcccssaisoesssixscenen
37. VNC 0 Reboots TPC Zoom ZOM requires v2 9 or higher ZOM 1264 Changes the zoom setting of the lens under motor control ZOM 1264 1 ZOM 1264 1 1 Write P1 Location P2 Approach direction NOTE Approach is optional 1 Positive to Negative Approach 1 Negative to Position Approach Read P1 Real time position P2 Current direction P3 Moving Status 0 not moving 1 moving Related commands are Intelligent Lens System ILS Lens Horizontal Offset LHO Lens Vertical Offset LVO and Focus FCS For single parameter functions listed in Table B 1 you can determine the parameter s range with the request message ASCIICODE M For example LPL M What is the minimum and maximum lamp limit LPL MO000 5000 Minimum lamp limit 0 maximum lamp limit 5000 If a function code has multiple parameters see B 2 Messages with Multiple Parameters their ranges cannot be requested B 14 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction B 2 Messages with Multiple Parameters Certain messages are more complex and require multiple parameters in order to relay complete information These messages are described in detail below B 2 1 Error Messages ERR An error message is generated by the projector TPC and contains a numerical error code a message specifier 1 e type of error such as System Error and a text explanation of the error In addi
38. assured by design alone installers service technicians trained operators and all other users must maintain a safe environment at all times Please read through and understand all warnings and precautions before attempting to operate the projector Labels and Markings Observe and follow any warnings and instructions marked on the projector The exclamation point within the equilateral triangle indicates related operating maintenance instructions in the documentation accompanying the projector The lightning flash and arrowhead symbol within the equilateral triangle indicates non insulated dangerous voltage within the projector s enclosure that may be of sufficient magnitude to constitute a risk of electric shock General Precautions Be aware of the following general precautions in all CP2000 SB installations 1 Never look directly into the projector lens or at the lamp The extremely high brightness can cause permanent eye damage 2 For protection from ultraviolet radiation keep all projector housings intact during operation Protective clothing and safety goggles are recommended NOTES 1 The American Conference of Governmental Industrial Hygienists ACGIH recommends occupational UV exposure for an 8 hour day to be less than 0 1 microwatts per square centimeters of effective UV radiation An evaluation of your workplace is advised to assure employees are not exposed to cumulative radiation levels exceeding the government guideline
39. be assigned to GPIs and GPOs GIO 13 h LampOn Important Changing to a 3D channel with GPIO usage will permanently delete the macro assignments for those GPIOs GIO I3H therefore it is suggested that those GPIOs used for 3D channels GIO 13h lampon not be used for macros GIO I3L P1 input 1 5 or output 1 5 GIO 131 lampoff P2 Macro Name GIO 03 SystemHealth Predefined GPI macros GIO 03 LampOn GIO 03 System Health LampOff DouserOpen DouserClosed AuxLensIn AuxLensOut Channel 101 through Channel 116 Predefined GPO macros System Health Lamp State Douser State Auxiliary Lens State Image Scaling Enable Disable IMS IMS 0 Enables or disable image scaling 0 disable 1 enable Intelligent Lens System ILS requires v2 9 or higher Method of reading and writing ILS information See Section B 2 4 Intelligent Lens System ILS Internal Test Pattern ITP ITP RGB 12Bbit Split Ramp Enter test pattern filename to display pattern ITP Enter to turn off the test pattern B 6 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHKISTIE Section 1 Introduction Function Code Examples Description and Parameters Lamp Changed LPC LPC 60123456 100 CDXL 20 Records the serial number hours logged on la
40. by installer or administrator USE A PCF OR NOT The availability of functions in the Custom menu depends on whether you choose to utilize pre defined configuration files PCFs already downloaded to projector memory Figure 3 8 or whether you prefer to implement your own settings from within the Custom menu Although pre defined PCFs were originally intended as part of content from the distributor so that the intended image quality is not compromised this practice is rare Instead PCFs may be created using DCP Librarian and downloaded to the projector Most applications such as cinema post production and alternative or non cinema displays require that one or more display parameters be individually adjusted clear the Use PCF checkbox Main Status Custom advanced Admin about w e z fiseoscor scope yi Source resolution aspect ratio and off set Choices defined by installer or administra tor CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 Always select for cinema sources Use full cinema processing amp scaling Use for all cinema sources plus DVI sources 60 Hz or lower Adjust Color Space Gamma LUT CLUT Target Color amp Source if cleared e Always de select for cinema source e Always select to apply custom settings defined as a PCF using DCP Librarian Refresh Update Refresh all selection lists available in 3D Custom menu ie i Clear 1 or more channels Restore factory def
41. can access the lamp via security key Complete lamp specifications are provided in Section 8 6 Lamps Lens Mount amp Auxiliary Lens Mount The standard lens mount secures and seals a primary zoom lens within the projector and provides manual adjustment of focus zoom and offset Adjacent to the primary mount an optional Motorized Auxiliary Lens Mount MALM may be added providing smooth and fast positioning of a 1 25x anamorphic lens or 1 26x wide converter in front of the primary lens Such lenses horizontally spread a pre squeezed image back into its wider 2 39 1 scope image and is most typically used in side masked theatres Leveling Feet For most cinema installations the projector is inclined slightly forward to match screen tilt and to minimize the amount of vertical offset required Turn the adjustable feet to increase or decrease projector height as needed for proper leveling and or slight tilt Refer to Section 2 4 Adjusting Tilt and Leveling Pedestal The multi purpose pedestal provides 1 housing for numerous harnesses and the main power supply a k a lamp ballast 2 a stable and adjustable base for the projection head 3 a central location for accessing all connections and 4 connection of AC The pedestal is closed and locked medium security for normal operation 3 4 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction Power Cabling NOTE Not included with projector In
42. close the filter door and secure with 2 screws 5 and 6 in Figure 6 3 CP2000 SB User Manual 6 11 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE 5 Filter installed 6 Secure filter door 2 screws Figure 6 3 Replacing the Air Filter 6 5 Replacing a Lens 6 12 A variety of primary lenses can accommodate different throw distances and specific types of installations see Section 8 Specifications To replace or change a lens 1 Release the lens locking lever UP position 2 Pull out lens and replace with a different primary lens as described in Section 2 1 4 Lens es 3 Secure with lens locking lever down position 4 Calibrate the lens See Section 2 7 Basic Image Alignment for details CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE 7 Troubleshooting If the projector does not appear to be operating properly note the symptoms present and use the following guide to assist you If you cannot resolve the problems yourself contact your dealer for assistance NOTE A qualified service technician is required when opening an enclosure to diagnose any probable cause e 7 1 Power e 7 2 Lamp ZS TPE 7 4 Ethernet 7 5 Cinema Displays 7 6 Non Cinema Displays CP2000 SB User Manual 7 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 7 1 Power 7 1 1 Project
43. computer The sync width is part of the blanking time TTL VIDEO A type of RGB video with digital characteristics TAMPER INTERLOCK A switch that detects when the light engine compartment is unlocked It is monitored by the electronics to log accesses If activated encrypted playback such as cinema presentations for example will be interrupted TERMINATED A wire connecting a single video source to a display device such as a projector must be terminated by a resistance usually 75Q for video THROW DISTANCE The distance between the front feet of the projector and the screen Also called Projector to Screen Distance Always use the correct Christie throw distance formula to calculate the proper throw distance 5 required for your lens THROW RATIO Throw ratio throw distance screen width TINT Balance of red to green necessary for realistic representation of NTSC signals TMDS Transition Minimized Differential Signaling is the basis for DVI Digital Visual Interface TRAILER Motion picture material presented prior to screening of the feature so called because they were originally presented following the feature Trailers are generally manufactured and created by the distributor in close cooperation with the producer they are distributed by trailer specialists at no charge Types of trailers include previews teasers house and or policy trailers advertisements and public service announcements CP2000 SB User
44. e Password Phrase TPC user password TIPS Use the Initial Local Folder to store the location where you keep the TI install files Enter ISMP in the Initial Host Folder to save steps later Keep other settings as default Click OK to go back to the Host List window Under the Advanced tab ensure the selection to Use PASV mode is unchecked Figure 3 44 In the Host List window click your desired site and then click Connect to connect to the TPC FTP server Both devices should now appear in the FTP windows Transfer the file from the PC left side of screen to the TPC ISPM folder right side of screen NOTE PC should be pointing at SSM HEX The TPC should be pointing at the IPSM folder Close the FTP program and reboot the TPC Troubleshooting If FFFTP fails to download files properly reconnect the TPCServer and try again If FFFTP still fails to download files properly re boot the TPC by disconnecting then re connecting it Host Setting General Advanced Kanji Code Dialup Special Profile Name Host Name Address Username Password Phrase service I Anonymous Initial Local Folder en Initial Host Folder rent alder F Use last accessed folder as default Hast Timezone GMT 3 oo x I Sune folder movement Security Auto z Fort 21 Defaut Account Commands After Connection n Cancel Help Figure 3 44 Host Setting Advanced Tab If FFFTP still
45. encoded SHOW SCRIPT A small file consisting of automation cues in addition to a play list triggering theatre events action data and possibly including parameters that allow the program to be tailored for a specific venue or engagement A show script is created by the exhibitor or installer and provides automated presentations Automation not yet available SNMP The Internet standard protocol developed to manage nodes servers workstations routers switches and hubs etc on an IP network SNMP enables network administrators to manage network performance find and solve network problems and plan for network growth SOURCE The device such as a server connected to the projector for supplying incoming data SOURCE SETUP Refer to Channel A 12 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CH IS TIE i Section 1 Introduction SWITCHER A signal selector specifically the Marquee Signal Switcher formerly manufactured by Christie can be connected for adding more sources to a projector SYNC This term refers to the part of the video signal that is used to stabilize the picture Sync can occur in three forms e Composite sync the horizontal and vertical components are together on one cable e Sync on green the sync is part of the green video e Separate syne or HSYNC and V SYNC the horizontal and vertical components of the sync are on two separate cables SYNC WIDTH The duration of each sync pulse generated by a
46. is no interlock problem such as an open lamp door a new lamp is likely needed CP2000 SB User Manual 3 57 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHRISTIE 3 8 3 Adjusting Lamp Power LiteLOC or Manually There are two different lamp modes for general operation you can maintain either a specific brightness level LiteLOC or a specific lamp power level NOTES 1 Requires Advanced Admin TPC rights 2 Keep in mind the formula Current Amperes x Voltage Volts Lamp Power Watts 3 Adjust LiteLOC before or after adjustment of lamp position Using LiteLOC Maintain a specific brightness level from your lamp over time as follows Figure 3 46 1 Inthe TPC s Advanced Lamp menu adjust Lamp Power until the desired light output is reached at the screen typically 14 fL Any LiteLOC will automatically be disabled Step 2 man Status custo Advanced Step 3 bet a fe ace E H Looneo tone Preference Lamp Lamp History J Lens J Test Pattern J User Figure 3 46 Setting LiteLOC 2 Click Set to record the current brightness reading in memory NOTE Arbitrary units of measure are shown above the light output bar 3 Enable LiteLOC As the lamp ages and loses efficiency the projector will gradually and automatically supply more current to the lamp as necessary to maintain your chosen level of light output for as long as possible the light level is read from an intern
47. lamp life by more than 20 as an old lamp becomes increasingly and dangerously fragile resulting in possible explosion To determine the age of your current lamp consult the Status menu in the Touch Panel Controller Lamp hours appear under Environment Lamp Lamp hours are also displayed in the password protected Advanced Lamp menu and the Advanced Lamp History menu It is recommended that you replace the air filter with every lamp replacement or sooner in dusty or dirty environments Check its condition monthly in all projectors CP2000 SB User Manual 6 7 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHi IS TIE i 6 4 1 Lamp Replacement Procedure 6 8 NOTE For this procedure you will need a compatible Christie Xenon CDXL or CXL lamp as shown in Section 8 Specifications never install a lamp intended for a different model or projector Warning 1 Make sure to use the correct wattage lamp supplied by Christie 2 Lamp replacement is to be done by a qualified service technician only 3 EXPLOSION HAZARD Wear authorized protective clothing whenever the lamp door is open Never apply a twisting or bending force to the quartz lamp body Before You Begin Read and follow all other general lamp precautions in Section 6 1 Warnings and Guidelines STEP 1 Turn Off Main AC a Allow the fans to run at least 10 minutes for cooling b At the breaker panel on the projector set the 3 phase MAIN AC circuit breaker to OFF Warnin
48. most cinema installations the AC power cord emerging from the pedestal toe is hard wired to an appropriately rated breaker connected to the AC supply in your building Note that all CP models require 3 phase power but can be configured in one of 5 different ways depending on the AC available at your site Six wire sites include single phase AC also The power cable provides AC to the entire CP2000 SB system and is disconnected only by turning off all breakers at the wall Projection Head The projection head houses the critical illumination and optical components as well as the DLP Cinema processing technology responsible for combining light and incoming source signals into brilliant high resolution digital displays Source inputs route through the pedestal toe or their servers are rack mounted at the rear of the pedestal and are connected during installation to the Source and Communication Connection Panel located on the underside of the projection head Projector function is controlled via the Touch Panel Controller or other communication from a controller The projection head must be closed and locked for all operation Security Locks STANDARD SECURITY for PEDESTAL Standard security locks on the lamp door and on each pedestal door help limit access to authorized personnel Identical duplicate keys for these three locks are provided with each projector TAMPER RESISTANT HIGH SECURITY for PROJECTION HEAD Components in the projection
49. new display area and or cropping Return to original default settings Cancel new unsaved settings Table 3 16 Admin Screen Menu Options ADMIN SCREEN MENU OPTIONS Presentation Presentation points define the display size and location default full 2048 x 1080 panel See Pre sentation Notes below Cropping Cropping hides unwanted data useful if the image appears keystoned etc See Cropping Notes below Letter Box Letter Boxing ensures that all image data is displayed and its aspect ratio is maintained See Letter Box Notes below Lens Factor Define the auxiliary lens needed 1 25 for the CP2000 series to stretch an image horizontally Leave at 1 default if no auxiliary lens is needed Slidebars Create Screen Adjust coordinates for presentation area and or cropping as desired Save current presentation oroppin lens factor and auxiliary factor settings as a Screen file accessed and applied from within the Custom menu Restore Cancel new unsaved screen settings Test Apply current settings to the image without saving 3 38 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction PRESENTATION NOTES Presentation points define what region of the projector s available display area responds to incoming data By default the projector will use its complete display area scaling the incoming data as necessary If for some reason y
50. of the lens mount 1 If the Motorized Auxiliary Lens Mount MALM is present ensure to move the MALM to the OUT position before performing any lens calibrate or reset functions on the Motorized Primary Lens Mount to prevent collision between the projection lens and the MALM 2 Hazardous moving parts Keep fingers and other body parts away To adjust ILS settings for a particular channel 1 Select a channel from the drop down list 2 Use the designated buttons to adjust Focus Horizontal X and Vertical Y Offset and Zoom Copy ILS settings to another channel To easily copy the settings from the current active channel to another channel use the Copy Lens Settings to Channel feature Select the channel from the drop down list and click Copy to apply the changes Use the buttons to adjust _ Main Status Cust Custom Advanced Admin About Diag the Offset l laisean r Focus Use the buttons 5 to adjust the focus Minimize maximize zoom Use this feature to copy __y specific lens settings Copy Lens Settings To Channel overte multiple f 1998x1080 Flat XYZ x Copy Page 1 Page 2 3D Control Lamp Lens 11 11 06 Figure 3 14 Custom Lens Menu Options Table 3 8 Summary of Custom Lens Menu Options CUSTOM LENS MENU OPTIONS Focus Click the buttons to automatically adjust the focus Offset Click the up down left right buttons to adjust the image and make it square on the scree
51. or left and right will be discarded NOTE Keep Letter box checked for all cinema presentations Unused pixels Complete image _ Incomplete image An ee eI SS Admin Gamut Menu The primary function of the color Gamut menu is to ensure that the projector can achieve any specific known and pre defined industry color performance standard called a target color within its current environment and within a desired tolerance In this menu you can record measurements for currently projected uncorrected colors modify or create custom Target Color Gamut Data TCGD files for new color gamut performance and set how closely you want to match the target white Recording the projector s uncorrected color performance is typically completed as a final step like a calibration after installation For this one time procedure the installer measures initial native e uncorrected colors at the screen enters the data as Measured Color Gamut Data on the left side of the Gamut menu and typically saves an MCGD file called OnSite By default the projector will use this MCGD to calculate and implement precise processing modifications needed to achieve any target color gamut on screen essentially compensating for the type of port window screen lens light output ambient light and other current environmental factors influencing on screen colors These various industry standards for color performance TCGDs will then be consistently achieved from source
52. pedestal floor Attach no other wires here e Connect L and N 200 230 VAC single phase e Connect 1 2 and 3 342 456 VAC 3 phase o If 3 phase with neutral fed from 3 phase 5 wire e Make sure ground wire is connected directly to the frame ground stud on the pedestal floor Attach no other wires here e Connect 1 2 3 and N 342 456 VAC 3 phase e No L available Connect jumper from to L o If 3 phase only 4 wire This configuration is not possible Use 5 wire or 6 wire only Neutral is required Warning Ground earth connection is necessary for safety Never compromise safety by returning current through the ground 2 14 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction Special Adjustments for Some AC Supplies AC levels can vary depending on region Check the following when installing NOTES 1 Requires voltmeter for up to 400 VAC 2 Consult the Interconnect Drawing in pedestal 3 Disconnect from AC power before moving the jumpers JUMPER FROM IGNITER TERMINAL 2 As set from the factory the igniter jumper located on terminal 2 connects to T2 This configuration is used when 207 265 VAC 400 VAG rating are present as it is for most countries If you find your incoming AC is below 207 VAC connect terminal 2 jumper to T1 instead Igniter If AC 207 265 VAC dumper between 2 and T2 1 1 2672 3 4 5 G DSW g
53. rate multiplication less than 6 2 may flicker at slow incoming frame rates 3 DEFINE 3D SYNC INPUT LOCATION For dual inputs Status Custom advanced Ravin ET e Set L R Input Reference option to Active Ie a Port A B L R or vice versa Set the Input GPI to None Saa These two settings tell the rest of your 3D system that incoming 3D stereo sync infor Left LIR1 L2R2 v mation is included with the two L R image data inputs rather than routed separately to Step 5 fhotus the GPIO port For future single input 3D sources where the Step 6 server supplies a separate 3D stereo sync to the projector s GPIO port instead set Input GPI according to which input number is used i e according to your GPIO cable wiring Figure 3 58 Setup for 3D 4 DEFINE L R DOMINANCE For the Input Frame Dominance choose the leading frame left or right Correct order depends on the cameras used during filming and is needed to ensure smooth motions An incorrect setting creates motion artifacts 5 DEFINE SYNC DISPLAY LOCATION e Set L R Display Reference to Not Used e Set Display GPI to None CP2000 SB User Manual 3 69 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 6 DEFINE SYNC OUTPUT Set L R Output Polarity to Inverted NOTE f the display appears reversed i e background appears close and foreground appears at a dis tance you will need to ensure that the cable connecting server outpu
54. reading projector information See Messages With Multiple Parameters later in this Appendix TCG filename Select the stored target color gamut file to apply to the current display TDC 10 420 Time amp Date TMD TCG What TCGD is currently in use TCG P7V2 The P7V2 TCGD is in use 3D Controls TDC TDC 1 Turn 3D controls ON OFF or sets specific 3D controls Example shown Set dark time to 420us For all other 3D controls see Messages With Multiple Parameters later in this Appendix TMD 2003 08 13 14 21 00 TMD 2003 08 13 14 21 00 Set read the time and date in the projector s real time clock P1 Year yyyy P2 Month 01 12 P3 Date 1 31 day of month P4 Hour 0 23 24hr clock P5 Minute 0 59 P6 Second 0 59 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 B 13 Section 1 Introduction CHRISTIE Function Code Examples Description and Parameters User ID UID UID JSMITH PassWord Allows remote access to a projector where a specific user name and password is set up and required NOTE This command is only necessary when the remote access setting in the projector is set to login required P1 User Name e g JSMITH case insensitive P2 Password e g PassWord case insensitive Virtual Network VNC requires v2 7 or higher and TPC 60 66 VNC 1 Start VNC server NOTE Should only be used for training
55. red green and blue light elements of a projected image so that they appear as a single element In this projector convergence can be adjusted by Christie service personnel only CURVED SCREEN A projection screen which is slightly concave for improved screen gain Curved screens usually have screen gains which are greater than 1 but viewing angles much less than 180 Curved screens are not recommended for use with this projector DCDM Digital Cinema Distribution Master A file or collection of files formatted for exhibition and comprised of all the components of the title A reference size of about 200 GB per title is likely DDC The Display Data Channel VESA standard enables communication between PCs and monitors and is based on E EDID protocol DMD Digital Micromirror Devices used in this projector for processing red green and blue color data DSM Digital Source Master A title s native source files in acquisition format edited to create the distribution master and for reformatting for NTSC HDTV DVD etc and potentially archived DVI The Digital Visual Interface standard signal supplies digital RGB sync PC and clock information to the single link DVI 1 or DVI 2 ports on the projection head DETAIL The sharpness of a display from a video source DIFFUSED SCREEN A type of rear projection screen which spreads the light striking it Screen gain is less than 1 but audience viewing angles are increa
56. temperature in the card cage red blue DMDs integrator prism or SSM has exceeded the operating specification e FAN SPEEDS caused when a main intake fan card cage fan or the laminar air flow device fan fails or is too slow LAMP EXPIRY appears when lamp has reached the end of its life as defined in the Lamp Limit setting Important For normal operation do not disable alarm triggers CP2000 SB User Manual 3 51 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 3 6 3 6 1 3 6 2 3 52 Remote Control of the Touch Panel Controller Most TPC projector functions can be controlled remotely typically at a controller via simple bi directional ASCII messaging on an Ethernet communication link WHAT SETUP IS NEEDED To control these TPC functions remotely via your own controller you must open an Ethernet socket between your controller and the valid TPC address Refer to Section 3 6 6 Setup and Shutdown for complete instructions Note that only one physical connection is permitted at any given time and access to remote functions may be limited by the installer Do not use an RS 232 serial link Understanding ASCII Message Formats All remote control information passes in and out of the TPC as simple messages consisting of command code and any data related to it Such messages can be a command to set a projector parameter at a specific level such as changing to a certain channel Or the controller can reques
57. the projector near a radiator or heat register or within an enclosure 6 2 2 Air Filter It is recommended that you replace the air filter located near the lens corner of the projection head whenever you replace the lamp or sooner in dusty or dirty environments A clogged filter reduces air flow and can lead to overheating and failure of the projector Check monthly Refer to Section 6 4 Replacing the Lamp amp Filter for instructions It is also recommended that you visually check the laminar airflow device LAD just beyond the filter opening The LAD should be nearly white or light gray in color 6 2 3 Liquid Cooler The liquid cooler system circulates liquid to and from the DMDs in the CP2000 SB projection head reducing their operating temperature to an acceptable level Periodically check the coolant level visible through the gauge window on the non operator s side of the pedestal and make sure that it remains between the two notches preferably closer to the top notch If the liquid cooling system should fail it will trigger an over temperature alarm window FILLING THE COOLER The cooler should require filling only upon projector installation refer to Section 2 1 Assembly and Connection of Components Fill with Christie approved coolant Jeffcool E105 provided in the liquid coolant fill service kit P N 003 001837 02 Danger HAZARDOUS SUBSTANCE The coolant used in this product contains ethylene glycol Use caution wh
58. to a dif ferent network and will not interact until the other device is also changed accordingly When SNMP selected Enter specific IP address where trap information device status notification i e fan fail ure is sent Subnet Mask All IP Addresses for a network belong to the same Subnet Mask as defined by the network admin istrator Default Gateway Apply Not used All entries are ignored Implement your current Ethernet Configuration settings Trap OID Retrieve information on the condition of a device from a specific MIB Management Information Base structure Default old MIB structure 11273 new structure 25766 Changes in the IP Config menu automatically change the projector IP address appearing in the Admin General menu which identifies which projector the TPC is currently set to control HOW TO CHANGE YOUR PROJECTOR S IP NETWORK ADDRESS For a stand alone projector its default Ethernet network settings are fine and should not be changed In a projector that is to be networked however this default address will likely be invalid for the network at a given site Consult the site s network administrator to determine the necessary settings for compatibility with the local network then use the TPC to define these new settings in the projection head NOTES 1 Password protected requires a Christie installer login 2 Projector can be on the network during these changes if desir
59. unless Set is pressed defining a new LiteLOC setting See Table 8 1 Minimum and Maximum Lamp Power by Lamp Type on page 8 6 for lamp power ranges Set With the desired light output measured at the screen press Set to automatically enable LiteLOC The current brightness level will be maintained as long as possible NOTE Arbitrary units shown here not footlamberts or lumens CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 3 25 Section 1 Introduction CHY IS TIE i Custom Lens Menu This menu is used to modify the Intelligent Lens System settings for a particular channel Adjust the Focus Horizontal X and Vertical Y Offset or Zoom by clicking the respective buttons in a step wise manner or holding the button down for continuous movement You may experience a slight delay in the response rate of the lens upon selecting the buttons Position values on the menu will change in real time When holding down a button for continuous movement the lens will begin to accelerate until the maximum velocity is reached NOTES 1 Manual adjustments of the lens is for temporary use and will be lost once a channel is changed 2 This menu is for advanced users only 3 Keep clear of rotating parts Remotely operated motors may start to spin without warning 4 Avoid long hair jewelry and loose clothing exposure to the knobs during manual adjustment 5 In case of emergency unplug the line cord to immediately halt movement
60. voltage terminal and insulator to remove accumulated dust or dirt Air Flow Interlocks The lamp fan vane switch is located within the lamp cooling compartment The extractor vane switch is located just inside the top duct on the projector lid Check and if necessary clean the switches to remove accumulated dust or dirt that could impede movement Within the exhaust duct connected at the top of the projector adequate airflow must be maintained and routed to outside of the building Inspect regularly and confirm that 1 there are no obstructions or kinks within the ducting 2 all air intake areas of the CP2000 SB are unobstructed and 3 exhaust airflow is within the range shown in Table 2 1 on page 11 Ensure lamp wiring does not interfere with vane switch Refer to Section 6 2 Maintaining Proper Cooling Laminar Airflow Device LAD Whenever checking replacing the air filter on the side of the projector also visually check the small square laminar airflow device LAD just beyond the filter opening The LAD should be nearly white in color if very dark rare it may have to be replaced by a qualified service technician Contact Christie or your dealer Replacing the Lamp amp Filter The high brightness of your projector is provided by a Xenon lamp mounted at two ends within a reflector and housed in the locked lamp compartment of the projection head When the lamp approaches the end of its life it must be replaced do not exceed warranted
61. 014 Table of Contents CHY IS TIE OTT aee E E a E E wap ace wee 3 65 FOCUS iiaa a pecs a E NA A E AE 3 65 39 2 Auxdiary LenS sarean cs ee eta tn ee eases eo we esate 3 65 3 10 Wo tkine with 3D spe foc nisiecsdses mnir i A E E E EE TE OER E AES 3 66 SOA 3D DESC LOIN erinoides K E E E E OEE 3 66 3 10 2 What DoI Need for 3D nirien Ea E EEE EE ARREA iR 3 66 3 10 3 Supported Hardware Setup ucieccciaccqusvelatene aces dendedieiniedararaadnecmanacuend 3 67 3 10 4 Other Hardware Setups scccxsareecsncnssececvantivssancs scanungiaccasnenseusensdeconeamnsesseune as cncevenoneertienaurns 3 68 Dy WOLD 3D Ts CNS nnne EE OA RGE 3 69 Hardware TS CUS scsi ccuctenstnciateattve sdpnacasdunnssniseusshintontasuutsua A E 3 69 Web User Interface InStr Ctions sses ea aE aaa EAEE E EETA ERES 3 69 3 10 63 D Tro bleshogtihg iwssinccsasrusssniecnueu svisadsecnssh tennesstausnntaassndedvwnpiescnssuudseswaxanuanbscensdeonmurets 3 70 Using the 3D Test Pattern s ssnsoeneeeseessesseseesseeseseesstesesnsstesestsstessesstsstessensessresseeseesnssee 3 70 Image Break p paces dusiesiea sachs cava tarnrn R EEEE R ARTA RN EN 3 70 No SD EMEC ee E E E E E 3 70 G o sting Cross Talk cseseasacstatanclapnianocanscsbunsnsssdcceealaceuntalatecdnnishecensssdastbarneeasealaiecammabeaupseannds 3 70 Motion ATtifaGtS sossesrresiniast iar aE E E E R ER 3 70 Single 3D Input Does Not WOK ssicventssasisasectbisntenaassedassiasnes sevsanctiagieniesoussdeaseauanaesnnaaenseandes 3 70 3 11 W
62. 0162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 2 2 1 Support for Internal Servers Source A series of holes around the top perimeter of the pedestal frame accommodates strapping for support of internal equipment To maximize air circulation and cooling within the pedestal install your longest devices in the highest rack mount slot available where they will not significantly block airflow 2 2 2 Security for Internal Servers Source Upon installation of a rack mount server or source within the pedestal ensure to re install the pair of vertical rack protector posts at the rear They will overlap the sides of your rack mount equipment and help prevent access to the pedestal interior and theft of rack mounted equipment NOTE Keep on hand any extra CP rear covers horizontal plates removed for rack mounted equipment These covers must be re installed if the equipment is removed from the projector in the future Do not operate the CP with open slots at the rear 2 3 Connecting for Communications Many communications with the projector are initiated on the Touch Panel Controller TPC mounted at the rear of the projector Depending on the installation you may also need certain other serial and or Ethernet links to the CP2000 SB such as from a server or PC functioning as a controller or from an existing on site network including other equipment Connections are typically done at time of installation and then the projector is locke
63. 06 10 Sets which projector identified by its network address will be controlled by the TPC upon the next re boot Examples might include 192 168 206 120 or 192 168 206 LJ etc Valid IP addresses depend on the site ADR Which projector I P address is controlled by the TPC ADR 192 168 206 10 Projector 192 168 206 10 is controlled by the TPC Projector Configuration File PCF PCF TPC1 Use this pre defined projector configuration file PCF filename for processing This file contains TCGD CSC LUT AL LUT DG LUT CLUT and SOURCE information PCF What pre defined processing file is currently in effect PCF TPC1 The TPC1 pre defined proj configuration file is in use Projector Hours of Use PJH PJH The number of hours that the projector has been used incl standby and without a lamp How many hours have been logged on the projector PJH 5672 Maximum 16 777 215 hours Projector Rental Hours PRH PRH How long has the projector been running with the lamp on PRH 1251 Proj has run 1251 hours with the Jamp on Pull Down Offset PDO requires v2 7 or higher PDO 2 0 field offset to 1 1 field offset to 2 2 field offset to 3 3 field offset to 4 4 field offset to 5 PDO Request field offset PDO 002 Response indicating field 3 offset CP2000 SB User Manual B 11 020 100162 06 Rev 1 03 2014
64. 0D000G000 GPIO oltsstalo 99009009 mm LITIST DVI 1 From Ethernet hub _ Cinema Server Ext mal or within pedestal Vinema Serve May be rack mounted Connect to AC at site in rear of projector a or within pedestal Connect to Ethernet hub at site or within pedestal Soe ol A PANEL A RS 232 A 6 202 q RS 232 B ooog o ol 299900900000000 oocaoccoocooootoo LI GPIO O ETHERNET OG 000 oa0a This panel is located on the underside of the projection head near the front Access from within pedestal Pc Connect to AC at site amp Or within pedestal Figure 2 24 Connecting an External Non Cinema DVI Source CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CH IS TIE Section 1 Introduction IF INTERNAL Sources servers are often rack mounted in the projector rear with cabling routed directly to the underside of the projection head See Figure 2 25 and Figure 2 26 Install as follows 1 Remove the pair of rack protector posts from the rear of the pedestal 2 Remove the required horizontal rack covers security plates 3 Rack mount the desired equipment within the pedestal 4 Re install the pair of rack protector posts Keep extra cov
65. 1 x 7 if external server is supply ing separate 3D sync at GPIO Sets which GPI to use Use None only Sets which GPO to use For synchronizing 3D stereo or via GPI Sets 3D sync output True or True v Inverted LIR Display Reference peripherals such as emitter z Not Used Dark Time Adj fo us screen etc Sets time between L R A L R Output Polarity Output Delay T fo us blanking time for glasses etc to close open Output Delay P 0 deg Paget J Page 2 3 control tame res O Shifts GPO pulse Pulse timing is shifted in relation to vertical frame Shifts GPO pulse in degrees Not used Figure 3 11 Custom 3D Control Menu Options Table 3 6 Summary of Custom 3D Control Menu Options CUSTOM 3D CONTROL MENU OPTIONS Enable Activate 3D controls and auto set Input to 292 Dual Input and Data Format to Unpacked 4 2 2 in the Custom Page 1 menu Test For confirming proper Sync Output setting i e which GPO is connected to your 3D peripherals such as emitters glasses etc L R Input Reference Defines how 3D stereo sync input is supplied currently ports A and B only See L R Input Refer ence Notes below Input Frame Dominance Defines frame order L R or R L required for 3D perspective Correct setting ensures smooth motions and depends entirely on the original source mastering L R Display Reference Always Not Used unless a separate 3D stere
66. 14 CHRISTIE Section 1 Introduction 8 8 Environment 8 8 1 Operating Environment Temperature 10 C to 35 C 50 F to 95 F Humidity non condensing 20 to 80 Altitude 0 3000 meters 8 8 2 Non Operating Environment Temperature 25C to 65 C 13 F to 149 F Humidity non condensing 0 to 95 8 9 Weight amp Size Shipping Weight Projection Head Pedestal Total 355 Ib 161 4 kg 450 Ib 204 5 kg 805 Ib 365 9 kg Installed Weight Without Lens Projection Head Pedestal Total 240 lb 109 kg 350 Ib 159 kg 590 Ib 268 kg NOTE 4 1 weights subject to change See page 8 8 Standard Dimensions W x L x H 25 63 5 cm x 55 5 141 cm x 54 137 2 cm with longest primary lens no anamorph Size with Anamorph W x L x H 25 63 5 cm x 62 157 5 cm x 54 137 2 cm with auxiliary lens mount amp lens CP2000 SB User Manual 8 7 020 100162 06 Rev 1 03 2014 Section 1 Introduction ALL i i iE ma i f T a el p E a CHRISTIE CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHAISTIE Section 1 Introduction 8 10 Standard Components e Pedestal on casters Refer to Section 1 2 2 Software Requirements for pedestal types e Projection head with lens mount and TPC e Lamp choices shown on Section 8 6 Lamps e primary zoom lens high contrast choices listed below e A
67. 24Hz signals can be increased by a maximum factor of 5 2 DARK TIME and OUTPUT DELAY NOTES The dark time between incoming L R frames provides a brief interval of non image time in microseconds us for your switching device such as shutters in glasses to complete its switch Ideally when this interval is properly set and exactly suits the speed of your device neither eye sees image data intended for the other eye This helps to prevent color artifacts and ghosting while ensuring that each eye sees all intended data NOTE Because the Dark Time interval essentially increases frame rate increasing this setting beyond its range for the current frame rate factor will cause image break up 2048 x 1080 displays may be cropped Likewise a setting less than the minimum is not supported and will simply revert to the minimum interval The Output Delay setting shifts the 3D sync in relation to the Dark Time interval starting each frame slightly earlier or later Adjust only as necessary too much offset can cause bleed through where each eye sees some data that is intended for the other CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction Custom Lamp Menu This menu provides controls for maintaining consistent light output over time or setting a precise power level for the lamp As shown in Figure 3 13 the Custom Lamp menu provides controls for maintaining a specific light output over time LiteLOC
68. 4 3 6 0 1 38 80908 1 51 100 vertical 70 horizontal 5 5 8 5 1 38 809080 5 1 100 vertical 70 horizontal Primary Zoom Lenses High Brightness Max of Image Below or Above Lens Center 1 25 1 45 1 108 274101 01 100 vertical 70 horizontal 1 45 1 8 1 108 275101 01 100 vertical 70 horizontal 1 45 2 05 1 108 335102 01 100 vertical 70 horizontal 1 6 2 4 1 108 336103 01 100 vertical 70 horizontal 1 8 2 4 1 108 276101 01 100 vertical 70 horizontal 1 8 3 0 1 108 337104 01 100 vertical 70 horizontal 2 15 3 6 1 108 338105 01 100 vertical 70 horizontal 2 2 3 0 1 108 277101 01 100 vertical 70 horizontal 3 0 4 3 1 108 278101 01 100 vertical 70 horizontal 4 3 6 0 1 108 279101 01 100 vertical 70 horizontal 5 5 8 5 1 108 280101 01 100 vertical 70 horizontal 8 2 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction MAX OF IMAGE OFFSET FROMS LENS CENTER OPT AUXILIARY LENSES 1 25x Anamorphic 38 809054 5 1 n a determined by primary lens for 2 39 1 scope screen 1 26x Wide Converter 108 281101 01 n a determined by primary lens for 2 39 1 scope screen Motorized Auxiliary Lens Mount 108 111102 xx n a determined by primary lens Maximum offsets are reduced when simultaneously offsetting horizontally and vert
69. 75 FFIB Satellite 76 FFIB Sequence 72 FFIB FPGA Main 73 FFIB FPGA Boot 74 FFIB Startup FPGA 71 FFIB DMD Data P2 Notes FPGA e Data CHRISTIE If Pl 5 Self Test 0 Interface Board 2 N A 3 System Supervi 1 Processor Board 4 ILS Motor Control 10 Space remaining on TPC IPSM KB 11 Space remaining on TPC Storage Card KB 12 Space remaining in TPC memory KB sor Module SSM For any test 0 OK 1 failed 0 Ok Non zero failed B 2 6 3D Controls TDC A number of 3D controls enable setup and adjustment of incoming 3D source material Parameter P1 activates B 22 the specific control and P2 sets the desire d adjustment 0 Disable 3D n a 1 Enable 3D B PS 2 Frame Rate Multiplication f FNR oy fL R input reference is 2 or 3 typical DAR GAMERS Slow Wee We Ue Perec NNN CNRS 3 mber directly Il Il NH ND NT N Ne I T NO Ne N nN Y 7 nN R input reference is 0 1 4 5 6 or 7 rare 3 L R Input Reference 0 Use assigned GPI true polarity 1 Use assigned GPI inverted polarity 2 Left on Port A Right on Port B 3 Left on Port B Right on Port A 4 White Line Code true polarity 5 White Line Code inverted polarity 6 Blue Line Code true polarity 7 Blue Line Code inverted polarity CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTI
70. 8 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CH IS TIE i Section 1 Introduction LUMINANCE The signal representing the measurable intensity comparable to brightness of an electronic image when the image is represented as separate chrominance and luminance Luminance also expresses the light intensity of a diffuse source as a function of its area measured in lumens or candles per square foot 1 lumen per square foot 1 foot lambert SMPTE RP 98 calls for a luminance of 12 to 22 footlamberts for theatre screens Refer to _Foot Lambert LUX The amount of visible light per square meter incident on a surface 1 lux 1 lumen square meter 0 093 foot candles MENU A list of selectable options displayed on the Touch Panel Controller METADATA Descriptive data about the format of the content e data about data When receiving metadata digital cinema projectors will know the correct aspect ratio of the image and the sound processor will know the correct format of the audio all without effort on the part of the person setting up the show on a particular projector MIB A database file defining a particular network object such as a device TPC server etc that can be monitored by a network management system such as SNMP NTSC VIDEO A video output format of some video tape and disk players There are two types of NTSC National Television Standards Committee video NTSC 3 58 and NTSC 4 43 NTSC 3 58 is used prima
71. Alarm Window in addition to interlocks and problems with the SSM I2C or lamp which are all permanent triggers It is recommended that all triggers remain enabled during normal operation Disable only in an rare emergencies when the alarm appears to be mal functioning without real errors Lamp Limit Enter the hours 0 5000 that are expected for this lamp typically no more than the number covered under warranty Expiry Message Select to display the Lamp Expiry Message on the TPC when the lamp reaches its defined lamp limit Language Choose English or Chinese TPC menu text for next re boot System Calendar amp Clock Reset the system date time Adjust the desired component date hour minute second and save with the Set button Screen Saver Enable disable a TPC screen saver and set its start up delay NOTE To use a unique screen saver a user defined bmp must be downloaded to the TPC replacing the default CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Advanced Lamp Menu Section 1 Introduction The Lamp menu provides controls for optimizing lamp alignment LampLOC maintaining a specific light output over time LiteLOC or setting a precise power level for the lamp Two read only areas display related lamp performance details the bar graph represents the current light output and if LiteLOC is enabled a heavy line shows the chosen LiteLOC setting In addition the New
72. Bit Identifies sets field offset polarity CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 3 21 CHRISTIE Section 1 Introduction 3 22 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 Custom 3D Control Menu This menu provides numerous controls for adjusting and synchronizing incoming 3D signals always dual L R HD SDI signals at the SMPTE A and B ports with each other and with external 3D equipment such as screens emitters and glasses The Custom 3D Control menu options are summarized in Figure 3 11 and Table 3 6 Add a check in the Enable checkbox in order to 1 enable 3D display and adjustment parameters 2 automatically configure the Input and Data Format on the Custom Page 1 menu For full 3D application notes including a step by step tutorial for use refer to Section 3 10 Working with 3D Toggle 3D function ON OFF Defines source amp 3D sync input gt active Port A B LIR x type Frame order For correct L R p Left LIR1 L2R2 v pairing amp smooth motion Sets 3D sync input location With source data Not Used Enable 3D Test Pattern Main Status Custom advanced Admin About fe M Enabie B Test Sets frame rate per signals i e Fies 7 Ex 4 frames 2 signals Lae Frame Rates 2 bad Sets which GPI to use Use 1 LIR Input Reference Input Frame Dominance Input GPI None v Display GPI None x Output GPO cro
73. C login user name appears in the User Name box For example if you logged on to the TPC as advanced the User Name box will display advanced Other user names visible in the drop down list will be those with the same or fewer rights none will have more rights For each name their corresponding user rights appear in the User Level box directly below Type of user Main Status Custom Advanced Admin About l Factory Defaults e Service FERRER 1 8 characters Admin User Name service x Password 11n required for e Advanced login Editable when adding a 1 12 characters Confirm Py PEA user or to change j current login User Rights Defines which TPC menus each user name can access Service Admin Advanced Re define the password for the current login Add delete other users having the same or fewer rights Preference Lamp Lamp History Lens Test Pattern User 15 22 48 Figure 3 22 Advanced User Menu Options From your current login add or delete more users assign their rights or change the password of your current login See details in the table below Table 3 13 Advanced User Menu Options ADVANCED USER MENU OPTIONS User Name Upon entering the User menu this box displays the name of the current login The pull down list displays all other user names having equal or fewer rights Factory Defaults Ser vice Admin Advanced For new na
74. CDXL 60SD 6 0 105 170 CXL 20 requires adaptor kit P N 003 001728 XX NOTE A Lamp Power setting of 110 will exceed the maximum values shown here by approx 10 3 60 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHAKISTIE Section 1 Introduction 3 8 4 Adjusting Lamp Position for LampLOC Align a newly installed lamp as soon as possible to ensure optimized lamp performance and peak brightness at the screen for the life of the lamp NOTES 1 Before adjusting a 10 minute warm up is recommended 2 You can adjust lamp position either before or after adjustment of Lamp Power or LiteLOC 3 Footlambert calibration should be performed with lamp change i e 2K to 3K Use the Do Auto Button for LampLOC For best results in all installations align the lamp by pressing the Do Auto button in the Advanced Lamp menu The motors and sensors in the projector will work together to precisely position the lamp for optimized performance and brightness utilizing filtering to eliminate signs of lamp flicker Once aligned this LampLOC setting can be considered fairly stable for the life of the lamp When to Use the Individual LampLOC Buttons The individual LampLOC arrow buttons each of which moves the lamp in one direction only are provided as a reassuring back up should the Do Auto button fail or if you feel a manual operator assisted lamp optimization will result in more output Either measure your results with
75. CHECK SIDE TO SIDE LEVELING With a good test pattern on screen double check projector leveling refer to Figure 2 4 so that the top edge of the image is parallel to the top edge of the screen Refer to Figure 2 35 CP2000 SB User Manual 2 23 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH IS TIE j 2 8 2 8 1 2 24 Offset and Boresight Alignment A Vertical i Motorized VA To ensure proper offset for your site and consistently good Ex Offset focus in all areas of the screen a primary lens must be installed y Ni anchor and its lens mount precisely adjusted in relation to internal Horizontal Bol optics as described below If desired an auxiliary lens can then P rsioht oa be added to widen images for scope cinema displays Warning 1 If the Motorized Auxiliary Lens Mount MALM ena is present ensure to move the MALM to the OUT position Knob before performing any lens calibrate or reset functions on the Motorized Primary Lens Mount to prevent collision between the projection lens and the MALM 2 Hazardous moving parts eea Keep fingers and other body parts away NOTES 1 Projector Offset Focus must be fully assembled and powered up in its final location 2 lt gt Vied Keep clear of rotating parts Remotely operated motors may Boresight Bolt start to spin without warning 3 Avoid long hair jewelry and Figure 2 36 Anatomy of the Lens Mount loose clothing exposure to the knobs dur
76. CP2000 SB USER MANUAL 020 100162 06 CHAISTIE CHY IS TIE Table of Contents 1 Introduction 1 1 The PIS SCL OL ceranae a AE A E EEE E REEERE 1 2 111 New TF AMI CS 25st catatebes ineno a EE A N E 1 2 1 1 2 Listof AU Features acc icetede Peace acai une eavwacs torsos ona e nose cere xaas etek wee on aati ineine tinen ba nni Tee daian tes 1 2 1 1 3 How th Projector Works cccccsutnccysseedex riisiin ieas eiea elena aT RTEA eerie 1 3 12 List of COMPONEIIS snsdesaccmesasthvacsinotscsteancscsoupincsutsenstaesoitisauvencsdiusnioaiseseuscexsunideutasecsesoupineieaeiases 1 3 1 2 1 Power and Lamp Requirements sssessnsseseeseeseeseesstssesetsstesstesessresseestesessresesrrssessessrssres 1 3 1 2 2 SoftWare Requirements sisese ioiai aor aE AEE E E a EEE E ET EE RE 1 3 1 3 Purchase Record and Service Contacts a ccctecesnisscasseasceesenascueasedadecenstsaqeauasss evencatteaascantacssaareacdvucs 1 4 1 4 Who Should Use This Manual errsssiminanninannan nnana a a a a a 1 5 1 4 1 Typographical Notations esessseseesesseseesesseseesstsetsesststtstssesessestestssestesessesestesensesststesessee 1 5 2 Installation amp Setup 2 1 Assembly and Connection of Components cccccccceesceescessseceeeceeeceeceeeseecaeceseeeeeeenseecsaeeneeneees 2 2 2 1 1 Servicing Energized Live Christie Equipment sisssssdeccsssiacsastonsaraseningsssaiidanstaviaaaasaetdacessanens 2 2 2 1 2 Projection Head and Pedestal 5 iccticcccaucencarsnoncaneanee
77. D Device D 2 1 2 Assemble a cable according to guidelines shown in Figure D 1 and Figure D 2 Connect the cable to projector s GPIO port and to your 3D device In the TPC s Custom 3D Control menu set Output GPO according to the pins wired in the GPIO cable see Figure D 1 For instance if you have wired pins 10 and 29 to your 3D device set Output GPO to GPO 2 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Appendix E Repacking the Projector If you need to relocate or ship the projector repack the pedestal and the projection head with the original packing materials used for shipping CP2000 SB User Manual E 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHRISTIE E 2 Cardboard Lid Plywood Lid Ramp Top Foam Cardboard Sleeve Bottom Foam Sleeve Block for Feet Front Plywood Base Foam Base Cardboard Base Wood Skid Pallet Figure E 1 Packing the Pedestal and Projection Head CP2000 SB User Manual 020 100162 06 Rev 1 03 2014
78. DIN bayonet locking 64MB or higher Projection Compartment AC near Panel B at front Connector type amp rating 1 IEC 320 compatible 15 A rating Voltage range 100 230 VAC 10 Line frequency 50 60 Hz nominal Max inrush current 38A Max current consumption 2 4 A 100V Max power consumption 240 W Max current at this AC input 5A Lamp Compartment AC near Panel C at front Connector type amp rating 1 IEC 320 compatible 15 A rating Voltage range 200 to 230 VAC 10 Line frequency 50 60 Hz nominal Max inrush current 7A Max current consumption 1 A 230V Max power consumption 230 W Max current at this AC input 5A Lamp DC Max voltage 41 VDC Start up voltage 80 V min 107 V max Max current consumption 170A Max power consumption 6600 W CHRISTIE CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction CP2000 SB Pedestal 3 Phase Plus Single Phase Nominal voltage 208 VAC N America Japan 400 VAC Europe Asia Absolute operating voltage range 180 235 VAC N America Japan 342 456 VAC Europe Asia Line frequency 50 Hz 60 Hz nominal Inrush current max NOTE does not include lamp 38 A N America Japan 26 A Europe Asia Current consumption per phase max 6 0 kW 28 A 208 VAC N
79. Data is Cropped from Edges To display the missing material reduce image size to fill the display area available in the projector then stretch vertically to fill the screen from top to bottom Add the anamorphic lens to regain the image width 7 6 8 Display Quality Appears to Drift from Good to Bad Bad to Good 1 The source input signal may be of low quality 2 The H or V frequency of the input may have changed at the source end 7 6 9 The Display has Suddenly Frozen If the screen blacks out inexplicably it is possible that excessive voltage noise on the AC or ground input has interrupted the projector s ability to lock on to a signal Power down the projector refer to Section 3 3 Power down Procedure and unplug Then plug in again and power up as usual refer to Section 3 2 Power up Procedure 7 6 10 Colors in the Display are Inaccurate 1 The color tint color space and or color temperature settings may require adjustment at your input source 2 Make sure you are using the proper PCF TCGD and or CSC file for this source 7 6 11 The Display is Not Rectangular 1 Check leveling of the projector Make sure that the lens surface and screen are parallel to one another 2 Is the vertical offset correct Adjust as necessary using the vertical offset knob 3 Is the anamorphic lens straight Rotate to orient aperture correctly 7 6 12 The Display is Noisy 1 Display adjustment at your input source may be required Adjust
80. E Section 1 Introduction 4 Input Frame Dominance 0 Left L1 R1 L2 R2 1 Right R1 L1 R2 L2 5 L R Input Frame Reference GPI 0 None 1 7 GPI1 GPI7 6 L R Display Reference None not used se assigned GPI true polarity 7 L R Display Reference GPI 0 1 2 Use assigned GPI inverted polarity 0 1 8 L R Output Reference Polarity 9 L R Output Reference GPO 0 None 1 7 GPO1 GPO7 10 Dark Time 0 4500 us 11 Output Sync Delay 0 200 us CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 B 23 Section 1 Introduction CHY IS TIE B 24 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Appendix C Serial Communication This section explains how to link the projector to serial communication devices e C l Serial Links to Projector CP2000 SB User Manual C 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i C 1 C 1 1 C 1 2 C 2 Serial Links to Projector Standard RS 232 Devices From a PC connect a standard 9 wire RS 232 serial cable CTS RTS to the serial communication panel port labeled RS 232A on the Source and Communication Connection Panel located on the underside of the projection head near the front Note that a serial link is adequate for DCP Librarian use or for downloading new main software both tasks require a qualified Christie service technician It cannot be u
81. E SAFETY A safety control system integrated into the HVAC fire alarm and other infrastructure components of the theatre as well as the presentation system Comment In the event of a fire for example the life safety system may turn on the auditorium lighting to full intensity cancel the presentation audio and replace it with a PA microphone or pre recorded announcement turn the lamp off flash warning lights and so forth Every jurisdiction may have different statutory requirements for life safety systems LINEARITY The reproduction of the horizontal and vertical size of characters and or shapes over the entire screen LINE OF BEST VIEWING When light from a projector is incident on a screen the light reflects from the screen such that the angle of reflection equals the angle of incidence The Line of Best Viewing is along the line of reflection LITELOC A Christie software feature where samples of output light from a projector trigger automatic adjustments in the lamp ballast power in order to maintain a constant light output over time LOOPTHROUGH LOOPTHRU The method of feeding a series of high impedance inputs from a single video source with a coaxial transmission line in such a manner that the line is terminated with its characteristic impedance at the last input on the line Not applicable in CP2000 LUMEN The unit of measure for the amount of visible light emitted by a light source Rarely used in cinema applications A
82. E pixels 0x07 4 4 4 packed 12 bits DVI port 0x00 Unpacked 8 bits color default 0x01 Packed 10 bits color 0x02 Packed 12 bits color Data Logging DLG DLG 1 0 Minimum logging of activities e for errors only DLG 1 Standard logging errors plus select operations DLG 002 2 All activities are logged Error Message Enable EME EME 1 Enable error messages sent via Ethernet where EME 001 0 disabled and 1 enabled Refer to ERR CP2000 SB User Manual B 3 020 100162 06 Rev 1 03 2014 Section 1 Introduction Function Code Examples Description and Parameters Error Messages ERR CHRISTIE ERR 010 Generated for projector errors Provides error code error type and text explanation 01 Interlock Lamp Fan Error 02 Interlock Extractor Open 03 Interlock Lamp Door Open 04 Interlock Auxiliary Open 05 Card Cage Tamper Interlock 08 Fan Intake 1 09 Fan Intake 2 10 Fan Card Cage 11 Fan LAD 12 Fan Ballast 16 Temperature Prism 17 Temperature Red DMD 18 Temperature Blue DMD 19 Temperature Integrator 20 Temperature SSM 21 Temperature Card Cage 22 Temperature Ballast 23 ILS over temperature 32 Lamp Life Expired 33 Lamp Failed to Strike 35 Lamp Unexpected Lamp OFF 36 Lamp Reading Lamp Intensity Failed 48 SSM Communication Error 48 SSM Upgrade Failed 68 I2C Communication Error
83. EE E EE ere E Cen E EE EEEE 8 3 8 4 Touch Panel Controller caicccegautocecnaigecausa toned n E R 8 4 BS Power Specificati nS ssania criei e e EE A EEEE EE EE E 8 4 8 6 LAMPS ksieni aeres e E EEE R E EE AE E E E RA ERE EEEE 8 5 3 7 TRU AGO occ axresccxaencetecuhcumesselewiasisneivwndewennaAeastenvesdnsitinesutseesdastwaotedduaupesdiuoiocuseavesdexmcstavaxearssentiiness 8 6 BF caress ceca oe pe eng nea ORD wv TO 8 7 8 8 1 Operating Environment sssessesseessessesseessessesseessessosseessessoeseesseososseesseesoesotsseossessesseessesoes 8 7 8 8 2 Non Operating Environment c csesccessessseesscessccdnecsnscsssosaensenssseoascesenndecesnscssnsesonsenssanses 8 7 9 9 Weight amp SIZE peenei eE R EEE AEE EAEE EAEE E A E aa 8 7 10 Standard Components sssrin oae E E aE E aa a 8 9 A Appendix A Glossary B Appendix B ASCII Messages B l Function CodeS iesene pa e re Ea E aE E es can EAE aaee E ES Tere iene B 2 B 2 Messages with Multiple Par ameter sssaiaescsieiacnsstetdecassoheasaeaniverssanhannqateedeceshanaseeaancsataaaasee lane B 15 B 2 1 Error M ssag s ERR Josien nt E E EEA ERNETEN B 15 Additional Parameters for 001 System Errors and 002 System Warnings 06 B 15 Examples of Critical System Error 001 Messages ccccssccssceeseeeeeeessecseeceeeeeeeeeeaeeesaeens B 17 Examples of System Warning 002 Error Messages 0 0 ccscccesceeeseesceetseceseceeeeeeeeeeseessaeens B 17 B 2 2 For Your Information FYT sss
84. Fa PC This panel is located on the underside of the projection head near the front Access from within pedestal b S or within pedestal Connect to AC at site Figure 5 1 Non Cinema DVI Source Connection shown with external source Each DVI port accepts and will auto detect the progressive scan digital RGB sources listed in Table 5 1 displaying them in their original incoming format Currently DVI signals cannot be scaled to a different size and or aspect ratio Note that each DVI port is a single link port for a single link cable connector only Using this pair of ports as a higher bandwidth dual link or twin link pair requires additional hardware and is not currently supported see Figure 5 2 Table 5 1 Compatible Non Cinema DVI Sources All Digital RGB 8 bit Incoming Format Vert Freq Processing Path Required Display Format 640 x 480 60 Hz Non cinema 640 x 480 640 x 480 72 Hz Non cinema 640 x 480 800 x 600 60 Hz Non cinema 800 x 600 800 x 600 72 Hz Non cinema 800 x 600 1024 x 768 60 85 Hz Non cinema 1024 x 768 1280 x 1024 60 85 Hz Non cinema 1280 x 1024 1400 x 1050 60 Hz Non cinema 1400 x 1050 1920 x 1080p 23 48 Hz Cinema 1920 x 1080 1920 x 1080p 23 98 60 Hz Non cinema 1920 x 1080 2048 x 1080 23 48 Hz Cinema 2048 x 1080 2048 x 1080 23 58 Hz Non cinema 2048 x 1080 1920 x 1080 23 48 Hz Cinema
85. Fs Rare Numerous settings collected into a single Projector Configuration File further control processing variables for optimized display of specific source material Each PCF file typically created in DCP Librarian pre defines color space target color gamut source aspect ratio resolution and gamma a k a degamma settings for a cinema or non cinema source Once the collected settings are downloaded to the projector s internal memory their PCF can be assigned to the corresponding CP2000 input connection and quickly applied via a controller such as Christie s Zouch Panel Controller No further adjustment in processing should be required Refer to the DCP Librarian User 5 Manual for all DCP Librarian Setup Software operating details and procedures CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE 3 Operation This section describes how to use the controls and switches for basic operation of the projector once it is properly installed by a qualified service technician NOTE The illustrations provided are to enhance the understanding of the written material and may not represent your exact projector model e 3 1 Projector Basics e 3 2 Power up Procedure 3 3 Power down Procedure 3 4 Introduction to the Touch Panel Controller 3 5 Using the Touch Panel Controller TPC 3 6 Remote Control of the Touch Panel Controller e 3 7 Upgrading SSM Firmware 3 8 Working with the Lamp e 3 9 Working with th
86. IT 4 2 2UNPACKED unless otherwise noted M 1 001 Signal must include 3 2 pull down encoding and Ancillary Time code information Signal must include 2 2 pull down encoding and assumes field one 1 dominance Same as Prog Segmented Frame Tmage will be centered vertically on screen default Keep in mind that the projector will attempt to automatically adapt to any incoming data format that does not exceed either the bandwidth of the system or the frame rate limitations thus formats beyond those shown above may be compatible CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 4 3 Section 1 Introduction CHY IS TIE 4 2 4 2 1 4 4 Image Formats The two standard types of cinema displays flat and scope differ in their width to height aspect ratio as shown below Flat Image Scope Image Aspect ratio 1 85 Aspect ratio 2 39 Figure 4 2 Standard Cinema Formats Achieving either of these displays from a wide variety of incoming source material depends on proper settings in the projector as well as certain theatre conditions Projector Variables Electronic and Auxiliary Resizing Because the native resolution format of the CP projector closely matches the flat aspect ratio the native resolution being only slightly wider at 1 89 the projector can essentially show incoming flat images through its standard zoom lens Scope source material however is typically squeezed ele
87. K ETHERNET AND TPC POWER Within the pedestal confirm that the power supplies for the Ethernet hub and TPC are directly con nected to the terminal block Figure 2 8 From Ethernet Hub From TPC Power Supply Power Supply NOTE Both should be pre connected Figure 2 8 Check TPC and Ethernet Hub Connections to Power 2 6 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction h CONNECT LAMP LEADS 1 Ensure the igniter door is open From the ballast in the pedestal route the main black and white lamp leads through the nearby hole in the underside of the projection head See Figure 2 9 2 Route the NEGATIVE BLACK lamp lead through the hole in the lamp cooling compartment wall Warning 1 Ensure the PCB is directed toward the back and remains at least 34 from the high voltage terminal with braid connection 2 Route all igniter wires AWAY from 9 pin and 15 pin con nectors 3 Twist both ballast cables twice per foot 3 Connect the POSITIVE WHITE lamp lead to the POSITIVE igniter terminal 3 4 wrench This terminal also has a small PCB attached stack this on top of the lamp lead 4 Close and lock the igniter door To Lamp anode y wrench F required NOT SHOWN 2 3 and G are pre connected So y NOTES 1 Orient the PCB as shown capacitor may be inverted on some projectors D
88. L PAL N PAL M or SECAM to RGB video Not applicable to CP2000 XB VIDEO STANDARD A specific type of video signal such as NTSC PAL SECAM VIEWING ANGLE Screens do not reflect equally in all directions Instead most light is reflected in a conical volume centered around the line of best viewing Maximum brightness is perceived if you are within the viewing cone defined by the horizontal and vertical viewing angles WATERMARK Data embedded in essence that serve different purposes and that are either imperceptible or obvious robust or fragile Their usual purpose is for legal support of copyright and they may also be components of copy control schemes WHITE BALANCE The color temperature of white used by the projector A 14 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CH IS TIE Section 1 Introduction WHITE FIELD The area of an image that is white only For example a full white field is an image that is white everywhere A 10 white field is a white area usually rectangular that occupies 10 of the image the remaining 90 is black YCBCR A high end digital component video signal YPBPR A high end analog component video signal Sometimes called YUV Component or Y R Y B Y the YPbPr signal by passes the video decoder in this projector YUV See YPbPr ZOOM The adjustment of image size by means of a zoom lens CP2000 SB User Manual A 15 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH
89. LICABLE FOR CP2000 PROJECTORS Power ON OFF Input and Channel Source connection location and channel Signal Hor and Vert Freq of current source Standby ON OFF NOTE lamp remains on regardless OSD ON OFF screen display of Cine IPM menus CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 3 13 Section 1 Introduction 3 14 CHRISTIE ENVIRONMENT Projector Hours hours projector has been powered up and communicating with the TPC Total Lamp Hours hours logged for all lamps ever installed Lamp hours logged on current lamp Current Lamp current amps Voltage Lamp voltage volts Power Lamp power watts Footlamberts Footlamberts interpolated from min max calibration LiteLOC On Off At Maximum Power Interlocks Critical safety and or operation monitoring Lamp Fant rear of projector OK Failure Failure also triggers an alarm window Extractor Fant for ducting to outside world OK Failure Failure also triggers an alarm window Lamp Door louvered lamp door OK Failure Failure also triggers an alarm window Auxiliary OK Failure Failure also triggers an alarm window Tamper projector lid OK Failure Failure triggers an alarm window and stops CineLink 2 encrypted cinema processing Temperatures C or F Critical internal temperatures in C or F Card Cage 55
90. LY SUPPORTED Figure 3 57 Single Input 3D Systems 3 68 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 3 10 5 3D Instructions NOTES 1 Assumes a full 2048 x 1080 display and 3D enabled in the Custom 3D Control menu 2 3D stereo sync or reference signal is part of input signal matching the vertical sync Hardware Instructions 1 Connect two HD SDI signals from a 3D media server to the projector s SMPTE cinema ports A and B One carries left eye data the other right eye data Connect to either port you will configure the projector to multiply and interleave the L R signals properly Web User Interface Instructions 1 Click Enable 2 SET THE FRAME RATE NOTE 6 2 is commonly used for most 3D features which are comprised of resolutions slightly less than 2048 x 1080 Both incoming frame rates are likely too slow for flicker free 3D viewing and need to be increased within the projector for at least 96 Hz output For example a typical HD SDI rate of 24Hz is still only 48 Hz when L R are combined see Figure 3 56 In the Custom 3D Control menu set the desired Frame Rate N M ratio or number of frames displayed per number of frames for complete data For example a setting of 6 2 creates 6 frames from 2 inputs 144 Hz The resulting frame rate cannot exceed the maximum frame rate possible in the projector with 24 Hz full screen incoming signals use a maximum factor of 5 2 NOTE Frame
91. Lamp button activates a window for entering the serial number of a newly installed lamp This button is also available with an Operator login with the rest of the Lamp menu disabled refer to Figure 3 4 Read only lamp info Main Status Custom Advanced admin Aboli LiteLOC Enable Lamp Power ke 75 0 v LampLoc Current light sensor reading Set maintain consis tent light output 29 6 4351 Approximate Foot Lamberts Adjustable from 75 110 if LiteLOC is not in use or as temporary override LiteLOC setting desired brightness Position lamp for best Light Output sensor light output x 70 D O FL reading x axis horizontal a Ls ye y axis vertical a A Hours 153 z axis fore aft gt ob le Do Auto Preference Lamp New Lamp Click to record new lamp serial and reset lamp timer 11 10 37 Figure 3 17 Advanced Lamp Menu Options Table 3 10 Advanced Lamp Menu Options ADVANCED LAMP MENU OPTIONS LiteLOC Maintains a chosen light level at the screen over time the lamp ballast will gradually increase power to the lamp as necessary until it reaches the maximum level possible for the installed lamp To disable LiteLOC temporarily or permanently clear the LiteLOC Enable checkbox or adjust Lamp Power directly Set Brightness With the desired light output measured at the screen typical
92. Manual A 13 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE UNICODE The Unicode method of encoding produces a very large character set typically required for ASCII messaging in non Western languages such as Chinese Russian etc In unicode every number code is unique to a single character A limited number of TPC functions can be executed remotely via unicode or non unicode default messaging this is auto detected Refer to _Non unicode VARIABLE SCAN The ability of a projector to synchronize to inputs with frequencies within a specified range VERTICAL FREQUENCY The frequency at which images are generated Vertical frequencies vary amongst sources Also called vertical scan rate VERTICAL OFFSET The difference between the center of the projected image and the center of the projector lens For this projector this value is expressed as the maximum percentage of the image that can be projected above or below the lens center without degrading the image quality All CP2000 lenses have the same vertical offset range VESA The Video Electronic Standards Association establishes standards of communication between electronic components to help ensure universal compatibility VIDEO The signal that is used by display devices such as projectors to generate an image This term also refers to the output of video tape disk players and computers VIDEO DECODER An optional device that converts NTSC 3 58 NTSC 4 4 PA
93. NT DIAGNOSTIC INDICATORS The small colored indicators or virtual LEDs for environmental and diagnostic information are green during normal operation These indicators can change to indicate a warning yellow or critical error red status Yellow Warning Indicates an unusual environmental condition For example a temperature may be elevated and nearing its upper limit correct the problem by checking all cooling systems turning OFF the projector and cooling if necessary make sure to follow the standard shut down procedure Service may be required in some cases Red Error Indicates that 1 the environment has a serious problem or 2 a specific electrical component is not detected or does not appear to be functioning properly In some cases a module may need re seating In other cases service or replacement of a module may be required before the projector can resume normal operation Regardless a red indicator requires immediate attention Diagnostics Showing a question mark icon indicates an unknown status caused by a problem during initialization Try re booting the projector Note that if any of the small indicators are yellow or red the main warning icon on the status bar changes accordingly so that problems are also immediately detectable from other TPC menus In addition a full screen flashing red alarm window is triggered on the TPC for such problems as failed interlocks mandatory over temperature optional and f
94. OC no longer in effect Meter tracks SLE El DoAuto Newlamp Ea adjustment Preference Lamp Lamp History J Lens J Test Patter J User Figure 3 48 Using a Specific Power Level witl CP2000 SB User Manual 3 59 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHRISTIE UNDERSTANDING LAMP POWER VALUES The Lamp Power range of 75 110 represents 75 110 of the power appropriate for the installed lamp In other words you can apply anywhere from 75 of the maximum power intended for the installed lamp up to an over drive that exceeds the maximum rating by approximately 10 Both current amps and power watts thresholds are read Keep in mind that higher lamp power settings do shorten lamp life for best results avoid over driving a lamp for extended periods When using LiteLOC which automatically increases lamp power over time check the Status menu lamp power readings periodically as the lamp ages to prevent prolonged over driving Enter 75 110 Lamp Power en E a Applies 75 110 of the lamp power rating for the installed lamp EXAMPLE If a 4 5kW lamp is installed Lamp Power fes 110 0 E gt Applies 110 of 4500 power rating or 4950 watts Figure 3 49 Lamp Power Values Table 3 23 Lamp Current Ranges CXL CDXL Lamps kW Current Range amps CXL CDXL 20 2 0 60 85 CXL CDXL 30 3 0 90 120 CXL CDXL 45 4 5 95 155 CXL CDXL 60 6 0 105 165
95. Section 1 Introduction CHAKISTIE Function Code Examples Description and Parameters Pull Down Sequence PDS requires v2 7 or higher Screen Format SCF PDS 0 0 2 2 Pull down PDS 1 1 3 2 Pull down PDS Request current pull down PDS 000 Reply indicating 2 2 pull down Save SAV SAV Immediately save all changes to flash memory rather than waiting for eventual auto save or a power down SCF filename Selects a custom or standard screen file stored in the TI head Use this screen format file stored in projector memory SCF What is the current screen format SCF 1920x1080 Current screen format filename is 1920x1080 Screen Orientation SOR SOR 0 Sets the position of the projector relative to the screen 0 Front 1 Rear 2 Inverted Front 3 Inverted Rear SOR What is the current screen orientation setting SOR 0 Current screen orientation is normal front position Select Input SIN SIN 0 B 12 Select which projector P1 and input P2 to use P1 Input 0 Input A SMPTE cinema 1 Input B SMPTE cinema 2 Dual SMPTE cinema 3 DVI A non cinema 4 DVI B non cinema 5 DVI Twin 6 CineIPM input on DVI A 7 CineIPM input on DVI B 8 CineIPM input on DVI Twin 10 bit 9 CineIPM channel on DVI A 10 CineIPM channel on DVI B 11 CineIPM channel on DVI Twin 10 bit P2 required
96. Segmented Frame 1920 x 1080 29 97 Hz 1920 x 1080 25 Hz Prog Segmented Frame 1920 x 1080 25 Hz 1920 x 1080 24 Hz Prog Segmented Frame 1920 x 1080 24 Hz 1920 x 1080 23 98 Hz Prog Segmented Frame 1920 x 1080 24 Hz CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Source Standard Orig Format Vert Freq Scan Type SMPTE 295M 1997 NOTE Uses 1250 total lines per frame Section 1 Introduction Display Format Progressive SMPTE 295M 1920 x 1080 50 Hz Interlaced 1920 x 1080 25 Hz SMPTE 296M 2001 SMPTE 296M 1280 x 720 60 Hz Progressive 1673 x 941 60 Hz Progressive 1280 x 720 59 94 Hz Progressive 1673 x 941 59 94 Hz Progressive 1280 x 720 50 Hz Progressive 1920 x 1080 50 Hz 1280 x 720 30 Hz Progressive 1920 x 1080 30 Hz 1280 x 720 29 97 Hz Progressive 1920 x 1080 29 97 Hz 1280 x 720 25 Hz Progressive 1920 x 1080 25 Hz 1280 x 720 24 Hz Progressive 1920 x 1080 24 Hz 1280 x 720 23 98 Hz Progressive 1920 x 1080 23 98 Hz SMPTE 260M 1999 NOTE This standard does not officially support 60 M SMPTE 260M 1920 x 1035 60 Hz Interlaced 1920 x 1080 24 Hz 1920 x 1035 59 94 Hz Interlaced 1920 x 1080 23 98 Hz SMPTE 372M 2001 DUAL LINK All SMPTE 292m 1998 single link formats see above are available as 12 bit 4 4 4 dual link with the same performance format NOTE A sources shown are 10 B
97. TPC An interlock may be interrupting lamp function m i Se a Make sure the 220V connection near Panel C at the rear of the projector head on the underside is still plugged in 5 Replace the lamp 7 2 3 No Lamp Current Reading With this communication error the lamp will be powered by the last lamp power setting in effect 7 2 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 7 2 4 Flicker Shadows or Dimness 7 2 5 7 2 6 7 3 Poe E eS LampLOC may need re adjustment LampLOC may be in the middle of its adjustment Wait approximately 2 min Increase lamp power if possible Determine if it is mid level grayscale flicker beating adjust 3 phase balancing for minimized ripple requires qualified service technician LampLOC Does Not Seem to Work 1 Inthe TPC Advanced Lamp menu try adjusting lamp position using one button at a time watch light level for changes indicating lamp movement 2 Ifthe motors do not respond via any TPC buttons you can position the lamp manually within the projection head UV danger Qualified service technician only LiteLOC Does Not Seem to Work 1 Ensure LiteLOC is set and enabled in the Advanced Lamp menu 2 Changing the Lamp Power setting disables LiteLOC 3 Ifthe lamp power has increased to its maximum in order to maintain a LiteLOC setting LiteLOC is automatically terminated If the values shown in the Advanced
98. TPC Ethernet configuration if you have changed either or both of the following Any of the first 3 octets of the IP Address i e the network node The Subnet Mask Be sure to change the TPC address before re booting the projector Warning For both devices projector and TPC the Subnet Mask and the first 3 octets of their IP addresses must match otherwise the devices are on different networks and cannot communicate Do not re boot until this match is confirmed You do not have to change the TPC Ethernet configuration if you have changed only the last octet of the projector s IP Address In this case rare both devices still belong to same network and will be able to communicate with each other Change the TPC Ethernet network configuration below HOW TO CHANGE YOUR TPC S IP ADDRESS Select TPC at the top of the IP Config menu then change the TPC s IP address in the same manner as you changed the projector s address Warning The first 3 octets of the IP address must match those for the projector See Steps 2 and 3 above NOTE This is the simplified explanation of valid addressing A trained network administrator may expand the range of valid addresses To implement the address changes in your projector and TPC re boot Important Do not forget to re boot the projector CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction Admin General and Admin Lamp Menus NOTE nstaller login r
99. Test Pattern button on the Main menu of the TPC and will be displayed in the order of their appearance in this window The bottom window contains an alphabetical list of all remaining test patterns Together both windows form the master pull down list of test patterns available in the Advanced Preferences menu Advanced admin about EE Re order selected test patterns DC2K 13 Point paana for user 9 DC2K 171 Pon access DC2K Framing Alara mom 50 Grey Unch e a DC2k 17 Point alphabetical DC2k Framing Green Select to add to tee DC2K Framing Red user list Test Pattern User_ Figure 3 21 Advanced Test Pattern Menu Options TO TOGGLE A PATTERN INTO ANOTHER WINDOW Select a test pattern checkbox to instantly move the pattern to the other window TO RE ORDER SELECTED TEST PATTERNS To change the order in which a test pattern will be projected when cycled with the Test Pattern button highlight the name not its checkbox in the top window and use the arrow keys near the top of the menu to move the pattern higher or lower in the list CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Advanced User Menu Section 1 Introduction Manage TPC users passwords and user rights here you will be able to manage users having the same or fewer rights than your current login level and you can change the password for the current login Upon entering the User menu your current TP
100. VE BLACK lamp lead and the two igniter harnesses to the side of the connector nut Important Secure lamp lead FIRST on connector then remaining two igniter wires on TOP From Igniter 5 Ballast Figure 2 13 Secure Lamp Lead and Two Igniter Wires At this point the lamp pre wiring is complete Leave lamp accessible for now 2 8 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction STEP 6 Connect Two Cooling Host Ends Pedestal to Head During operation a closed loop of flexible tubing circulates cooling liquid stored in the pedestal to critical electronics components located in the front compartment of the projection head Looking into the pedestal the liquid will circulate counterclockwise NOTE The TOP graphic in Figure 2 14 is for pedestals manu factured before Fall 2006 The BOTTOM graphic in Figure 2 14 is for pedestals manufactured for Fall 2006 and after Projection Head Hoses non operator s side J g operator s side p i i Ea i A Ml i N i f fy i a y f i l NS Hf l i A x f it Li n ig ME E i y ARI ARA N iy AN Figure 2 14 The Liquid Cooling Loop CP2000 SB User Manual 2 9 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE 2 10 a T
101. Y IS TIE A 16 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Appendix B ASCII Messages Use the following ASCII messages function codes for remote communications with the TPC and its corresponding projector All messages must be sent via Ethernet NOTE Please refer to Section 3 6 Remote Control of the Touch Panel Controller for a complete explanation of remote communications setup message protocol and format B 1 Function Codes B 2 Messages with Multiple Parameters CP2000 SB User Manual B 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction B 1 Function Codes B 2 Table B 1 Function Codes CHRISTIE Function Code Examples Description and Parameters Anamorphic Lens AML OM 0 or AML 1 aml Move the anamorphic lens out 0 or in 1 or request status NOTE Requires Motorized Anamorphic Lens Mount optional Channel Icon CHI CHI S101 1 Assign second icon in list to represent channel 101 Range 0 15 Note the S required when specifying a channel other than the current channel CHI 15 aoe 16th icon in the list to represent the current channel Range 0 15 CHI What is the current icon CHI 004 The 5th icon represents the current channel Channel Name NAM NAM S108 Chicken Little or AMS 108 Chicken Little Changes or assigns a name to a particular channel Always pre ceded with S so that the nam
102. Yes 0 No 1 Yes 0 No 1 Yes None None Return Value 0 No 1 Yes 0 No 1 Yes 0 No 1 Yes 0 Complete non zero indicates In Progress 0 Complete non zero indicates In Progress 10 Move All Motors NOTE This command should be used to move all motors at the same time It is more efficient then using LHO Lens Horizontal Offset LVO Lens Vertical Offset FCS Focus and ZOM Zoom P2 X location P3 Y location P4 Focus location P5 Zoom location P6 X approach P7 Y approach P8 Focus approach P9 Zoom approach NOTE Approach is optional When no approach is specified a Negative to Positive Approach is assumed 1 Positive to Negative Approach 1 Negative to Positive Approach This is write only command CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE B 2 5 Examples of ILS Commands Section 1 Introduction ILS Command Result ILS 0 1 Sets ILS installed to Yes ILS 1 1 Sets Lens Reset on Startup to Yes ILS 2 1 Sets AutoILS to Yes ILS 3 Invokes Lens Calibration ILS 4 Invokes Lens Reset ILS 10 1023 264 800 1248 ILS 10 1023 264 800 1248 1 1 1 1 Moves all four motors to the specified offset focus and zoom locations Approach goes from negative to positive Moves all four motors to the specified offset focus and zoom locations Approach is s
103. a light meter at the lens and screen or simply watch the light output gauge in the Advanced Lamp menu Note that with these buttons you may attain a slightly higher peak than with the Do Auto button but the peak may not be centered on the lamp curve and lamp performance may not be optimized whereas the Do Auto button also utilizes filtering to eliminate the effects of any lamp flicker In general use the individual buttons only when you feel it is unavoidable HOW TO ADJUST IF USING A LIGHT METER First obtain peak readings on a light meter centered in front of the lens then at the center of the screen For each button continue in one direction then back up when reading begins decreasing NOTES 1 Display a 100 white internal test pattern 2 Use a tripod to center the light meter with the lens Distance from the lens does not matter You may need an attenuator or wish to construct an internal foil aperture first 3 This is an optional procedure use the light output gauge in the Advanced Lamp menu if preferred 1 Adjust forward aft z until the brightness reading in front of the lens is maximized Main Status Custom Advanced admin About 2 Adjust left right x and up down y until the a brightness reading in front of the lens is Measure at maximized es Re adjust forward aft z as necessary 4 Repeat Steps 1 3 as necessary Step 2 E B E ot 5 Repeat Steps 1 4 but reading at the screen instead E Steps
104. a target must be saved under a new TCGD filename entirely Once you have created a new TCGD file it will appear in the Custom menu where it can be selected for use in the display NOTE For most applications TCGD values are used simply to verify that displayed colors actually do match the standard i e you can measure each color at the screen and compare its coordinates to those appearing in the TCGD fields to confirm that the projected colors are accurate For special applications in which you want to create a unique target color standard enter new TCGD coordinates as desired and then save as a new TCGD file Apply as usual from the Custom menu GAIN NOTES Gain indicates the luminance a k a brightness or intensity of each color as compared to full on white ranging from 0 0 to 2 100 You may want to modify one or more gain values to precisely match color levels in other adjacent displays or to accommodate a studio s internal color management technique Gain would rarely if ever be adjusted for theatre use CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction WHITE TOLERANCE NOTES The chosen target for white White x y coordinates under Target TCGD may be relaxed if desired by establishing a small tolerance box around it This box represents four coordinates 0 1 2 3 plotted on a 1931CIE Chromaticity graph and may vary from TCGD to TCGD If desired define new tolerance coordi
105. access to all test patterns as well as certain system parameters See Table 3 9 for a complete description If selected displays pattern as 2048 x 1080 If not selected adjust cropping etc for test pattern Main Status Custom Advanced Admin About Current Test Pattern Conditions for triggering an alarm in the TPC window Over Temperature Fan Fail Choose language for TPC menus Stops upon opening of Advanced menu Select increment and adjust calendar time Enter the hours you expect to log on this lamp Lamp Life 2 000 V Expiry Message Click to save adjust ments when reset ting the clock Enable to display message when lamp expires reaches Lampi Limit Enable to display a screen saver on the TPC after the desired delay 15 20 58 Figure 3 16 Advanced Preferences Menu Options Table 3 9 Summary of Advanced Preference Menu Options ADVANCED PREFERENCE MENU OPTIONS Test Patterns Display an RGB 12 bit test pattern or turn patterns OFF Always turn OFF to resume normal operation Full Screen Enter a checkmark to display test patterns in full 2048 x 1080 resolution Clear the checkbox to work with cropping controls for screen size and shape as desired Note changes are temporary i e applied for the current test pattern only This control is not used for sources Alarm Triggers Choose which conditions you want to trigger an
106. acters as desired except for the following special characters these require a 2 character combination as shown in Table 3 21 Table 3 21 Special Characters for Text If you want this Enter this Description Backslash vt Quote Left bracket Right bracket 0x0A n New line if the text can be displayed on more than one line this will cause the next character to be dis played at the start of the line that follows the current one 0x1B x control code ESC 3 6 3 Sample Messages and Their Meaning Table 3 22 Sample Messages Desired Action Message Description Get current Chan CHA Request by controller for current channel Chan reply from proj CHA 101 Reply from proj that current channel is 101 Set Chan CHA 101 Switch to the first channel on the TPC Get picture mute status PMT Request by controller for picture mute status Picture mute reply from proj PMT 000 Reply from proj that picture is mute is off Set picture mute PMT 1 Turn the picture mute on blank the image CP2000 SB User Manual 3 53 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH IS TIE i 3 6 4 3 6 5 3 6 6 3 54 What is Actually Sent in a Message Although you will send and read all messages as strings of ASCII characters the actual message travels as a sequence of bytes Each character in a unicode message requires 2 bytes whereas t
107. al line Consider the value at the top of the meter as arbitrary i e not representing actual lumens or fL 3 29 Section 1 Introduction CHRISTIE Adding a New Lamp Select new lamp type from drop down list Enter serial number for new lamp installed Description of why lamp change is required Read only window that displays the _ information of recorded lamps eRe aT SAVE required Main Status Custom Advanced l Admin About ae New Lamp added to top of lis Lamp Type cxi 45 v i e Lamp timer will reset to 0 hours Serial FFFFO702 Hours fo Enter the number of hours logged th l Change Reason Lamp Type Change installed lamp Date Time Type Serial Number Hours 2008 10 13 14 20 CXL 60 ygkj1568 2008 09 11 04 56 CXL 60 Nia 37 2008 08 26 09 26 CDXL 605D0 test001 Test Pattern User 11 13 48 Figure 3 18 New Lamp Fields Preference Lamp Lamp History Table 3 11 New Lamp Fields NEW LAMP FIELDS Lamp Type Select lamp type using the drop down list Serial Touch to activate keyboard for editing Change Reason Select description that best explains why lamp was changed Save Touch to record the new serial number and date and automatically reset the lamp timer to the same value entered in Hours text box Hours Enter the number of hours logged on the newly installed lamp If
108. al light sensor 4 To change your LiteLOC setting adjust the Lamp Power as desired and then click Set The LiteLOC function will automatically begin to maintain this new setting WHEN SHOULD USE LiteLOC Typically most theatre installations would use LiteLOC for daily operation since it need only be set once for each lamp install and ensures consistent worry free brightness at the screen for as long as possible If desired reset LiteLOC to a different level at any time or override with a specific lamp power setting 3 58 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CH IS TIE Section 1 Introduction HOW LONG CAN I MAINTAIN BRIGHTNESS Software can maintain a LiteLOC setting until the required power exceeds the maximum rating for the lamp 2 0 3 0 4 5 or 6 0 kW by approximately 10 The lower your LiteLOC setting the longer it will take to reach this over drive threshold and the longer you can maintain the desired brightness For example a 6000 watt lamp 6 0 kW Main Status Custom Advanced can be safely driven at no more than 6600 watts To produce 14 fL at the screen a Maximum new lamp would likely need less than this SAUN C A example only Over time however the maximum rating perhaps 5120 watts aa E pian lamp will require more and more current in E Light order to produce the 14 fL until eventually B a rl bel the lamp wattage reaches its 6600 ry gt
109. alues 01 1998x1080 Flat XYZ Bl cory Paget Page 2 30 contra J tame tes _ ci Figure 2 44 Copy Channel Settings CP2000 SB User Manual 2 27 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH ISTIE i 2 8 5 Add Auxiliary Lens 2 28 If present swing the auxiliary lens in position in front of the primary lens It should magnify in the horizontal direction only stretching the image straight across the screen this requires that its aperture visible within the lens be vertically aligned with the screen If the image appears skewed loosen the locking ring on the auxiliary lens and rotate the lens as necessary until the wide image is horizontal Refer to the Motorized Auxiliary Lens Mount Instruction Sheet 020 100036 04 for details on mounting the anamorphic and wide converter lenses Anamorphic 1 25x 1 FOCUS PRIMARY LENS With the auxiliary lens in place re focus the primary lens using focus knob The goal is good focus at center and on all sides 2 FOCUS ANAMORPHIC LENS If horizontal focus in the image needs improvement focus the auxiliary lens too rotate its barrel as needed 3 RECORD SERIAL NUMBER Enter the serial number of your anamorphic lens in Advanced Lens menu Refer to Figure 3 20 Advanced Lens Menu Options on page 3 31 Wide Converter Lens 1 26x NOTE Use a gauge block or measuring device to establish basic alignment of the wide converter lens to the primary lens A WARNING Use t
110. an 101 power mode LPM S101 003 Reply to Chan 101 power mode request LPM If Lamp per channel reply is channel power mode otherwise LPM 2000 returns global power mode Lamp Per Button LPB LPB O 0 Off Lamp settings will be the same for all channels LPB 1 On Lamp settings will vary according to channel LPB 1 NOTE This setting determines whether lamp mode power and intensity are the SAME for every channel i e global or DIFFERENT for each CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction Function Code Examples Description and Parameters Lamp Power LPP LPP 2000 Specific power setting for the lamp in Watts LPP Value Range depends on the installed lamp LPP 2000 NOTE Specify desired channel with S Ifno S parameter is included the LPP setting will apply to the current channel when the Lamp Per Channel checkbox is enabled and to all channels when the checkbox is cleared LPP S101 2 Changes power value for channel 101 to 2000 LPP G Requests global power value LPP G 1608 Reply to global power request LPP S101 Request for Chan 101 power value LPP S101 2000 Reply to Chan 101 power request LPP If Lamp per channel reply is channel power otherwise returns LPP 2000 global intensity Lens Auxiliary LNA requires v2 7 or high LNA 1 25AN 1234567
111. an problems optional 3 12 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction Main Status Custom Advanced Admin About Description value amp Current 69 4 Voltage 214V Power 1476 Ww Foot Lamberts 37 6 FL Information Indicators _ gt amp LiteLOCc Or Interlocks Lamp Fan OK Environment Extractor Fan OK Diagnostic Indicators ______ 0 Lamp Door OK Auxiliary OK Tamper OK lw System Select to expand or collapse menu gt 5 Interface Board If Red Failure Service likely required If Yellow Red stop operation and correct the problem oO 15 37 36 Green All OK Yellow Environmental Diagnostics WARNING Red Environmental Diagnostics CRITICAL ERROR Main Status custom Advanced Admin About Description Value Built in Self Test a General System Power up Self Test Security Interlock Integrity I2C Scroll Read only Diagnostics Performed ARM FPGA Load FPGA Code Valid System 15 38 23 NOTE Requires service installer login Figure 3 6 Status System Menu Table 3 1 Summary of Status System Menu STATUS SYSTEM MENU ENTRIES SOURCE Projector Input Source connection location of current signal Signal Vert Freq CINE IPM NOT APP
112. any address changes and re boot to implement all changes 3 IP address shown in TPC Admin menu must match that of the projector 4 Ifyou still have trouble establishing communications with a projector added to an existing Ethernet network the projector s IP address is likely in conflict with another address already in use Contact your network administrator 7 5 Cinema Displays 7 5 1 Blank Screen No Display of Cinema Image Confirm all power connections are still OK Make sure there is no lens cap present Make sure the douser shutter is OPEN button is on TPC Main menu Make sure there is not a full black test pattern selected for display Is the correct display file selected Check the Zouch Panel Controller OND Or ee SD a Is the correct cinema port connected for this display file Check connections 7 5 2 Severe Motion Artifacts Most likely there is a synchronization problem with reversed 3 2 pull down in 60Hz to 24Hz film to digital conversion in your source The display file needs correction 7 5 3 Image Appears Squeezed or Vertically Stretched into Center of Screen Source data converted from film and pre squeezed for CP2000 SB s display format may require use of the anamorphic lens to regain full scope image width and proper proportions 7 5 4 No Image Just Pink Snow 1 Make sure the projector s lid is not open In the event it is open close the lid and pause or stop the show on the server Then press play on the
113. arge casters are typically used only when the CP is rolled into place for installation or if the projector is moved from one location to another When the projector leveling feet recommended for all installations are extended enough to raise the projector the casters will spin freely and can be removed if desired Communications and Source Connection Panel The Communication and Source Connection Panel located internal underside of projection head provides high security connection of the CP2000 SB to a variety of external equipment such as sources and controllers e ETHERNET Connect networked equipment such as PCs and servers to the internal Ethernet hub RS 232 A PC Connect a standard serial RS 232 cable for external serial communication with a PC laptop NOTE Does not support ASCII messaging RS 232 B RESERVED Unique protocol for Christie accessories only such as the Cine IPM 2K Other equipment will not function via this port PORTS A AND B CINEMA Connect a wide variety of high definition cinema sources to these SMPTE 292M bit serial standard interface BNCs DVI PORTS ALTERNATIVE NON CINEMA CONTENT Connect a wide variety of non cinema video and graphics sources to either of these identical single link DVI ports NOTE These are single link ports for single link cable connectors only Using this pair of ports as a dual link pair requires a special adapter not currently available e Changing a connection requires a
114. ary lens is installed select it from this drop down list The selections include anamorphic and wide converter lens This selection is grayed out when there is no auxiliary lens connected Serial Number Enter serial number of the installed lens Installed Enables disables the Intelligent Lens System ILS NOTE Installed must be checked in order to use ILS functionality Lens Reset On Startup Select this checkbox for the ILS to locate the sensor flags and the backlash of each motor at the same time Keep checked if you need to reset the lens often Calibrate Click Calibrate to calculate the amount of backlash for each motor and make the necessary adjustments to ensure proper motor range Calibration should only be used when changing lenses and is a necessary step at that time Lens Reset When Lens Reset is clicked the motors on the lens move to a central location mechanical center before moving back to the original position This feature is useful for initiating an auto lens reset Each motor can either be reset individually or select All Axes when prompted to reset the 4 motors in succession CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 3 31 Section 1 Introduction CHY IS TIE i Advanced Test Pattern Menu In the Advanced Test Pattern menu use the double windows to organize and manage the master list of RGB test patterns Patterns in the top window are available to the user via the
115. as DC2K Framing or RGB Alignment 1 The Horizontal Hold Screw acts as counter resistance to hold the lens mount in place once set Before adjusting the boresight loosen the Horizontal Hold Screw See Figure 2 39 2 Extend the lens focus completely Horizontal Hold Screw Horizontal Boresight Bolt 0 O Figure 2 39 Horizontal Boresight CP2000 SB User Manual 2 25 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH IS TIE 3 Adjust the Focus to retract the lens using the down arrow on the Main Lens menu See Figure 2 40 Watch the image at the left edge of the screen until it comes into focus If the image appears well focused on the left edge but not on the right determine if the right side focuses in front of or behind the screen If the entire screen come into focus skip to step 7 Focus Left Edge Center Main Status Custom Advanced Admin About Diag Figure 2 40 Adjust Focus 4 Continue retracting the lens a Ifthe right side of the image comes into focus before the lens is completely retracted then the image focuses in front of the screen See Figure 2 41 To correct this problem adjust the Horizontal Bore sight bolt to direct or aim the lens mount towards the LEFT to balance out the left right edges See Figure 2 39 b Ifthe right side of the image fails to come into focus then the image focuses behind the screen To cor rect this problem d
116. at the new lamp is neither under powered nor over driven Warning Do not attempt to ignite the lamp until its type is correctly selected in the Advanced Lamp menu Inthe Advanced Lamp menu select New Lamp a b Inthe Lamp History submenu select the correct lamp type from the Lamp Type drop down menu z Enter the serial number and the number of hours logged on the newly installed lamp gt Select the reason why the lamp was changed from the Change Reason drop down menu e Click Save to record the number and to reset the lamp timer The timer will now begin to log time for the new lamp NOTE You cannot edit the line items of recorded lamps therefore ensure you enter the correct information before clicking Save STEP 13 Turn the Lamp ON and Adjust the Lamp Position Press and hold the lamp button on the TPC Main menu Using the TPC adjust the lamp position within the projector as described in Section 3 8 4 Adjusting Lamp Position for LampLOC This ensures maximum performance with the lamp bulb well centered with the reflector and distanced correctly from the rest of the illumination system CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 6 4 2 Filter Replacement Procedure Replace the air filter whenever the lamp module is replaced or more frequently if operating the projector in a dusty or dirty environment Check monthly in all cases The filter is located on the
117. aults processing Choices defined by installer Default P7V2 The atre 422 Unpacked 10Bit v frcbcr2gom e Type of color decoding such as RGB or YCbCr as 6 rages Fae TA e Figure 3 9 Custom Page 1 Menu Creating Customer PCFs and Other Settings 3 19 Section 1 Introduction 3 20 CHRISTIE USE CINEMA PROCESSING OR NOT The cinema checkbox on the Custom Page 1 menu determines if the incoming signal is processed using the projector s full cinema path which enables image scaling and color correction but restricts resolution and frequency combinations If unchecked most of the projector s Processor Board functionality is by passed this disables scaling and color correction but is compatible with higher resolution and frequency combinations Generally use non cinema processing with DVI sources having high resolution and frequency combinations See examples in Table 3 3 Table 3 3 Processing Path for DVI Sources Examples RESOLUTION VERT FREQ TYPE OF PROCESSING 1920 x 1080 lt 48 Hz kf Cinema use full cinema processing 2048 x 1080 lt 48 Hz j Cinema use full cinema processing 1920 x 1080 49 77 Hz E Cinema use non cinema processing 2048 x 1080 49 72 Hz E Cinema use non cinema processing NOTE See Table 5 1 Compatible Non Cinema DVI Sources All Digital RGB 8 bit on page 5 2 for a more complete list Important Attempting to use cinema processing when the incoming DVI verti
118. b and soak in lens cleaning solution Tissue should be damp but not dripping 3 Gently wipe the surface using a figure 8 motion Repeat until blemish is removed Cleaning the Reflector IF DUSTY 1 Brush most of the dust off with a camel hair brush and or blow dust away with compressed air 2 Ifsome dust remains just leave as is air circulating at the lamp is unfiltered so some dust is inevitable Avoid unnecessary cleaning IF FINGERPRINTS SMUDGES OIL 1 First brush dust off with a camel hair brush and or blow dust away with compressed air 2 Fold a clean microfibre cloth and dampen with methanol Make sure to wipe evenly with the smooth portion of the cloth that has no folds or creases Do not apply pressure with your fingers use the solution in the cloth to collect the dirt 6 6 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction 6 3 3 Other Components 6 4 In a normal operating environment check clean and treat the following components every 6 months or so to help ensure proper lamp and projector function Lamp Fan A clogged lamp fan impeller or motor can reduce air flow leading to possible overheating and failure of the lamp Clean treat the impeller as follows 1 Vacuum loose dirt from the lamp fan impeller 2 Ifnecessary use a brush with hot water and suitable detergent Important Do not bend the impeller blades or loosen the balancing weights Igniter Clean the high
119. ble 2 amp connector iR B single link single iink connector connector Adapter 1 k a J gi i DVI Source i ae l A Twirlink X DVI Source Dual link Figure 5 2 Proposed Dual link and Twin link DVI Configurations NOTES 1 Neither the Christie dual link adapter nor the proposed 3rd party twin link source and cables shown here are currently available 2 Using both DVI ports with the Christie Cine IPM 2K enables 10 bit output and displays Consult the Cine IPM 2K User Manual for details CP2000 SB User Manual 5 3 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 5 2 5 4 Selecting the Source For any display the projector interprets incoming signal data according to one of 32 user selectable display files defined at the time of installation and or with each subsequent release of a new digital cinema feature and stored in projector memory Each file is essentially a collection of processing display settings optimized for a particular cinema feature or alternative non cinema content enabling consistent presentations with minimum further adjustment Each file is represented by an assigned channel button selectable over several pages of the TPC Main menu Depending on your installation you may have 0 32 different non
120. cal frequency is too high can cause a TPC start up error Turn cinema option OFF then cycle power OFF ON Table 3 4 Summary of Custom Page 1 Menu Options CUSTOM PAGE 1 MENU OPTIONS Channel Identifies sets button 1 32 for current Custom menu settings To assign a new channel for the current Custom settings select the desired display will also change and press SAVE Buttons representing channels appear in order on the Main menu Channel Name Current name or title for a button identifying a source such as a movie title or DVD Select to rename using pop up keyboard Up to 32 names can appear on the TPC Main menu 4 pages of 8 Large Icon button Shows icon defined for current source Click to assign a different icon Cinema Keep checked for most sources default ensuring that incoming data is processed using the com plete cinema path and scaled to fill the screen where possible Currently cinema sources A B pro jector inputs should always utilize the cinema path and scaling Uncheck only for incoming DVI having a frame rate gt 60 Hz if SXGA or gt 48 Hz if 2048 x 1080 as the cinema pixel clock rate is limited to 110 MHz Use PCF Enter a check to use a pre defined PCF for this source and prohibit further Custom adjustments the PCF components of Source Color Space Gamma LUT CLUT and Target Color will disappear then select the desired PCF from the Predefined Configurations list Clear the
121. ccess to the interior of the projector via the locked pedestal Unauthorized general users cannot connect disconnect CP2000 SB User Manual 3 3 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE Coolant Level Gauge This gauge indicates the current level of coolant present for circulating to the main electronics in the front portion of the projection head Keep the liquid level close to but not above the top notch Refill if the level drops near to the bottom notch Refer to Section 6 2 3 Liquid Cooler Exhaust Duct Connect the projector s 8 top exhaust hole to an outside vented duct with at least 10 of the last portion of the duct rigid at the projector The duct will also need a heat extractor providing the 600 or 450 CFM airflow required for all lamps Refer to Section 2 1 3 Exhaust Ducting Extender Legs The rear feet of the projector are attached to extendable legs for more radical tilt up to 12 than possible with the feet only For best optical performance tilt the projector so that it is parallel to the screen but always avoid radical tilt such as when the projector is much higher than the screen and rely on lens offset instead Refer to Section 2 4 Adjusting Tilt and Leveling for complete instructions on setting the tilt adjuster Lamps In the CP2000 SB use a 2 3 4 5 or 6 kilowatt lamp The lamp door must remain closed and locked for all normal operation Trained operators only
122. ce eeceesteeeteeeee 7 5 7 6 5 Portions of the Display are Cut Off or Wrap to the Opposite Edge ceeeeceesteeeteeees 7 5 7 6 6 The Display Appears Compressed Vertically Stretched cececcceceseceseceeeeeeeeeeseeeeseeees 7 5 7 6 1 D t 1s Cropped from Edges 5 iio aia ws acy sasndstossimscaahacetasehecxssbedecus areexquaneiareuesaasiae E 7 6 7 6 8 Display Quality Appears to Drift from Good to Bad Bad to Good eeeeeceeceesteeeteeees 7 6 CP2000 SB User Manual v 020 100162 06 Rev 1 03 2014 Table of Contents CHY IS TIE 7 6 9 The Display has Suddenly Frozen sesssnsssesssenseesessssessesesssresseserssressessrssressessesseesseeseesenssee 7 6 7 6 10 Colors in the Display are Inaccurate x ciccscvariacecaiaaeioereneatloceaineeesaaeeemaaaaaeeieke 7 6 7 6 11 The Display is Not Rectangular saisnccacsesusnesscndsncanancincdscnsoeaesunceeconenteneansnivactvendeaincanciessinens 7 6 7 6 12 The Display 1s NOISY spissen onen ea aE EE E EEE E EE EE 7 6 7 6 13 There are Random Streaks on the Bottom of the Image nsssssssessssssessessseseesseeserssssee 7 6 8 Specifications BMS gotta cas Racecar ah ode a E a a dnc aetna 8 2 Dae LITISGS sia lcatvauansscssanasasdvacesacessphastvsuneed E Ganbnemtes 8 2 tick INDUS PA T EEE T E 8 3 8 3 1 Cinema INPUtS vea a E EE E E T EE EG 8 3 8 3 2 Non Cinema DVI Inputs for Alternative Content s ssessssseeseeseseseessesersseesseserssressesese 8 3 ye eo CGONTOl POMS eRe r eere E
123. ce parameters such as synchronization with content language font type font color position etc in the current presentation Define the desired URI Uniform Resource Identifier i e cinema server or distributor providing the subtitling xml file you wish to examine then select Enable to begin the test Any errors encountered in file content or transmission from the server for example a lost file a server crash loss of communication with the server etc will appear in the window and the Enable checkbox will clear TEST METADATA xml Enable the Meta File button to test a supplied xml file required for auto configuring display parameters such as colors aspect ratio watermarks etc in certain distributed content Such metadata a k a data about data is embedded in the video stream content and should be modified only by the distributor but the test may result in errors pointing to problems in metadata content or its transmission from the server Which data type Non functional to test Find available servers Source and address for subtitle or metadata file xml Begin test of server amp file Update test results Similar to refresh Or see if subtitling is running Test results May show errors in xml content and or transmission from server Figure 3 60 Status Server Menu Options CP2000 SB User Manual 3 71 020 100162 06 Rev 1 03 2014 Section 1 Introduction 3 11 2 TPC Status D
124. cessary adjust TPC screen brightness and contrast via the Windows CE Display Settings for this device service password required If your TPC is enclosed in a blue casing use the small knob on the back of the unit to adjust screen settings CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHX ISTIE i Section 1 Introduction 3 5 1 TPC Main Menu Main status Custom Advanced Admin About Diag Ha 1998x1080 UA 2048x858 Flat XYZ Scope XYZ 8 Display Buttons channels Jis 1 Select pre defined source Ha 1998x1080 m 2048x858 Flat P3 Scope P3 Lamp ON OFF Douser Button Open and close the shutter 2 Image will change 3 Additional sources on 2nd jit page A Reserved r Reserved PCF Flat PCF Scope fA 1920x1038 pA 1920x804 Channel Menus g Fates P3 Scope P3 ee Status Button CH 1 8 e Go to Status Menu e Flash indicates an alarm User Level Button condition Color identifies user e Color indicators described rights Select to below Figure 3 5 Main Menu Options change Anamorphic Lens In Out Test Patterns Cycle through available test patterns Lens Intelligent Lens System Select to adjust lens mount NOTE The Status and User buttons in the bottom corners do not affect the projected display image TURN THE LAMP ON or OFF To toggle the lamp ON OFF press and hold the lamp button LOG ON By default with no login the TPC will of
125. checkbox if you wish to adjust the Custom settings this is currently recommended for all cinema use Refresh Button Updates all Custom settings such as Gamma Target Color etc to include any data newly added to projector memory via DCP Librarian setup software or TPC Admin menus 3D Button If present the current channel is for a 3D display set in 3D Control menu Reset Button Clear the current or all channel settings and return to factory defaults Input Identifies sets the location connection of the current source such as cinema ports A or B or a DVI graphics port Note that use of the twin and dual link DVI options requires special hardware Refer to Section 5 Non Cinema Operation Data Format Specifies the source type 8 10 12 bit and whether or not it is packed The projector will process the incoming signal according to the data format selected here Note that available data formats depend on which projector input is selected and will reset to a default value if an input has not yet been selected Use of DVI dual requires a separate adapter at the DVI connectors and use of DVI twin requires a special source Data format settings are not included in a PCF CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction CUSTOM PAGE 1 MENU OPTIONS Source Identifies sets the expected incoming source resolution and aspect ratio such as 1920 x1080 or Mk7 defa
126. cinema sources defined for use TO SELECT A NON CINEMA SOURCE With a non cinema source connected to the CP2000 SB use the main menu on the Touch Panel Controller to select the display button representing the desired non cinema source Once selected the button will darken and the projected display will change according to the corresponding file settings Refer to Section 3 5 Using the Touch Panel Controller TPC if you need help TO RETURN TO A CINEMA SOURCE At the Main menu of the Touch Panel Controller select one of the cinema display buttons pre configured for a cinema source input at port A or B the CP2000 SB will now ignore the DVI ports and respond to the cinema source activated by this button CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE 6 Maintenance This section describes methods for safely maintaining the CP2000 SB projector NOTE The illustrations provided are to enhance the understanding of the written material They are graphical representations only and may not represent your exact projector model 6 1 Warnings and Guidelines e 6 2 Maintaining Proper Cooling 6 3 Maintenance and Cleaning 6 4 Replacing the Lamp amp Filter e 6 5 Replacing a Lens CP2000 SB User Manual 6 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 6 1 6 1 1 6 1 2 Warnings and Guidelines This projector is designed for safe and reliable operation However safe operation is not
127. cludes a STOP button for installers service to exit TPC software entirely and return to Windows Status Custom Advanced Admin About See e 7 Exit TPC software and a aay od h return to Windows 1 4 available to installer C E E E only Touch Panel Main f List of all software ions in th Touch Panel Language English i aires me Touch Panel OS Resdoni only System Supervisor Main System Sunervisnr Rant Figure 3 38 About Menu 3 5 8 Understanding Versions in Your Projector Consult the About menu to determine the current level of a hardware or software component installed in your projector Upgrading any of these components requires a Christie service technician TOUCH PANEL Determines the software functionality of the Touch Panel Controller TPC its menu language and its operating system SSM Indicates which System Supervisor Module is installed H W and what SSM software is present Main and Boot portions ENGINE Indicates the main processing software of the projector This is a summary of the Interface Processor and Formatter Interface entries that appear below it in the About menu i e any change to one of these elements would automatically denote a new Engine version NOTE The remaining individual red green and blue formatters are independent of Engine version CP2000 SB User Manual 3 49 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 3 5 9 S
128. coordinates measured at the screen See Measured MCGD Notes below Pattern Off Leave the full field test pattern mode Target TCGD Activate each color and enter the x y coordinates desired See Target TCGD Notes below Gain Luminance intensity of each color when compared to white See Gain Notes below White Tolerance Define the location enter x y coordinates of each comer of a tolerance box around the target white point for the current TCGD A tolerance minimizes the light discarded in achieving the tar get white in the display and is recommended for theatre use Without tolerance the target white point will be matched precisely in displays using this TCGD regardless of how much light must be discarded See White Tolerance Notes below Checkbox Enter a checkmark to enable tolerance around the white point Delete the checkmark to match the white point precisely Restore Cancel new unsaved TCGD settings Cancel tested via Test button but unsaved MCGD settings See Restore Notes below Test Apply current settings to the image without saving Create MCGD Save current MCGD settings as a new OnSite or other file name NOTE OnSite is a permanent over write of any previous OnSite file and cannot be cancelled in the future except by another over write If desired create other MCGD files to reference under specific conditions and for spe cific sources or channels See Create MCGD Notes below Create TCGD Sa
129. creen red alarm window flashes if one of the alarm conditions shown in the left column of Table 3 2 is encountered Ifa safety interlock fails power will no longer reach the lamp DC output is stopped and the lamp button on the TPC Main menu will be disabled NOTES 1 4 failed safety interlock automatically prevents power from going to the lamp and disables the lamp button on the TPC Main menu Since most interlock alarm conditions are triggered by switches regularly check the operation of these switch levers 2 With interlock integrity restored the lamp button on the TPC Main menu is automatically re enabled Can Alarm Conditions Be Ignored Note every alarm window indicates a new condition In a given session the alarm window will not reappear for a condition that you have acknowledged shunted but not yet solved However if you cycle the projector OFF and ON again any persisting alarm condition will trigger the alarm window again Although it is highly recommended that the monitored over temperature and fan speed conditions always be set to trigger a flashing alarm window default this trigger can be turned off if desired by clearing the appropriate Alarm Triggers checkbox in the Advanced menu Once cleared such conditions will only trigger the yellow or red Status warning button rather than a flashing alarm window This can be helpful in rare cases where the alarm window is erroneously repeatedly triggered with no detectable error conditio
130. cribes the ability of Christie projectors having a motorized lens mount to automatically return to lens settings previously defined for a particular channel Not available in cinema projectors such as CP2000 INPUT A physical connection route for a source signal described by a 2 digit number representing 1 its switcher projector location and 2 its slot in the switcher projector INPUT SIGNAL Signal sent from a source device to the projector CP2000 SB User Manual A 7 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i INTERFACE MODULE A device such as the Serial Digital Input Module that accepts an input signal for display by the projector Interfaces are not used with the CP2000 INTERLACE A method used by video tape players and some computers to double the vertical resolution without increasing the horizontal line rate If the resulting frame field rate is too low the image may flicker depending on the image content KEYSTONE A distortion of the image which occurs when the top and bottom borders of the image are unequal in length Side borders both slant in or out producing a keyhole shaped image It is caused when the lens surface is not parallel to the screen LAMPLOC A Christie software feature where samples of output light from a projector guide the precise position of the lamp along 3 axes vertical horizontal and distance to lens so that lamp performance and output is maximized LIF
131. csssovcesranteactiviecsanusiadadenaieinudaseraivinnaeiees B 18 B23 History ELIS yaccanennnnrecnvantesanaaransecaartecysuntacany ESAR Ea AREE EA aeee EEr oxieteveneieratavaaptavcecatangenee B 18 B 2 4 Intelligent Lens System ILS sscis3ssaicesasnaceapdiatcvanbesadssnpeatdcasaseatensaeadauesaancaspaidccmniadieaions B 18 Examples OF ILS Commands xsccaitcusacwossenscsedinnsaienusdnanstenseesetleasciusisetineamusedudiiomsaneeteoncsessnntns B 19 B 2 5 System Status SST sca ssstesisnnnssatenpcnartevnadtncsssukanthaaaianewiaenvasvediacesacismesiadaiadassdarnbereatncssenbeaeee B 19 B20 3D Controls TDC siccesdiasemsieeeaetietiad na enantio B 22 C Appendix C Serial Communication C 1 Seral Links to Pi CO OK nesesite ea TEK EA E TEO REEE E S C 2 C 1 1 Standard RS 232 Devices essri a ra E E E EE C 2 C2 Ci PMI A E A E T E AA C 2 D Appendix D GPIO System Integration DLTH GPIO POl epes enorer EA AAEE EE E SE EEE D 2 vi CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Table of Contents D 1 1 Example GPIO and 3D Device scce cinsassusassatovesudeccenseccuseassavencsaracssenetacamnedensevatteersaavracnsenss D 2 E Appendix E Repacking the Projector CP2000 SB User Manual vii 020 100162 06 Rev 1 03 2014 CHRISTIE 1 Introduction This section includes information on the following 1 1 The Projector e 1 2 List of Components 1 3 Purchase Record and Service Contacts 1 4 Who Should Use This Manual CP2000 SB User Man
132. ct ratio The projector must be able to respond to the myriad of possible combinations projecting full images of the desired size content and proportion in every case This consistency is achieved by creating a variety of source files in projector memory each of which indicates the following for the projector Incoming resolution pixels across pixels top to bottom e Offset desired i e amount of data to discard Rare Section 1 Introduction Administrator login pis Installer login Source Screen Gamut IP Config GPIO Source Screen R Gamut IP Config GPIO amp General Figure 3 23 Access Rights for Admin Menus Desired aspect ratio i e the original display format to be recovered Although in rare cases the content distributor may include this source information as part of a pre defined PCF applied by using the PCF in the projector alternatively these variables can be defined either in the Source submenu in the TPC as described here or by using DCP Librarian With a good collection of assorted source files available in memory the proper file can then be quickly chosen from within the Custom menu for implementation in the projector whenever a matching input signal is encountered Note that for any source the projector relies on
133. ction 1 Introduction 4 3 4 3 1 Selecting the Cinema Source NOTE For details regarding all TPC functions refer to Section 3 5 Using the Touch Panel Controller TPC Touch Panel Controller Method As described in Section 3 5 Using the Touch Panel Controller TPC CP2000 SB displays are usually pre configured so that any user can correctly display a desired feature simply by selecting the corresponding button on either page of the Main menu displayed by the Touch Panel Controller There are a maximum of 32 different display buttons available at any one time 8 per page with most users locked out of other processing controls available in other Touch Panel Controller menus For cinema sources in particular which are displayed according to strict parameters pre defined by the producers of the feature and implemented in the projector by a CP2000 SB installer administrator or trained operator this simplicity ensures that the intended display can be selected quickly and easily by any user To change to a new feature do the following Ensure the CP2000 SB and TPC are both powered up and operating normally On the Touch Panel Controller select the Main menu tab e On the Main menu page 1 or 2 press the desired display button the image will update according to the many display parameters defined for this source Refer to Section 3 5 Using the Touch Panel Controller TPC for other operating details Status Custom Ad
134. ctor Center Aimed projector Figure 2 2 Centering lt gt Aerial Views Note that when a particularly short throw distance combines with a very wide screen you may have to for feit some aim and stay more parallel to the screen In such cases some lens offset can reduce the keystone distortion Later when your projector is up and running adjust precise image geometry and placement as described in Section 2 7 Basic Image Alignment STEP 3 Extend All Feet For permanent installations and more stable images the projector should be firmly on the floor rather than on its casters Extend rotate the foot located behind each ae aye caster until the lens opening is fairly well centered with ange ae the port window Figure 2 3 Lock top nut in place 1 aae aust Remove caster if desired NOTE There is no need to i GA pax adjust leveling and or tilt at this point wait until all ry fC other components are mounted installed and refer to Section 2 4 Adjusting Tilt and Leveling A 4 Figure 2 3 Adjust Feet STEP 4 Install Touch Panel Controller a Attach the Touch Panel Controller TPC pre assembled with its ball joint base and mounting arm to the matching ball joint base secured at the rear of the projector Figure 2 4 b Connect to the TPC cable routed through the nearby hole in the projector rear The other end of this cable is pre connected to the inter
135. ctronically that is it is distorted into a narrow image characterized by unusually thin people and then its pixels are stretched horizontally through the auxiliary lens so that the full 2 39 image width appears on screen The image becomes wider but not taller See Figure 4 5 gt Compressed q Normal Scope Image G CHk ISTIE in O CHRISTIE Lae ad Screen edge Figure 4 3 Typical Method for Achieving Scope If the incoming material has not been pre squeezed by the distributor you can squeeze it by using a source file in which the combined settings for 1 incoming source resolution and 2 desired aspect ratio define the necessary compression The incoming material will then be squeezed into a narrower area on the projector s DMD panels with the final aspect ratio setting determining the actual degree of compression Refer to Section 3 5 Using the Touch Panel Controller TPC for more information about choosing Source menu settings CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHAISTIE 4 2 2 Theatre Variables Masking Section 1 Introduction In order to present either type of feature on a single screen a theatre typically uses masking to conceal any unused edge s of the screen These movable panels or curtains are most commonly installed along the top edge of the screen changing the height of the screen but not its width The screen shown in Figure 4 4 also has a bottom mask e A
136. d near the front Access from within pedeste PANEL A RS 232 A D000 Sioo00Gh9 epovcene seeccecem O PLIITSTTs ol 000000000000000 aoaocaoaoannoaooo GPIO DVI 1 From Ethernet hub Cinema Server External or within pedestal Cinema Serve May be rack mounted 2 Connect to AC at site in rear of projector or within pedestal Connect to Ethernet hub at site or within pedestal Figure 4 1 Cinema Source Connections External Source Shown The identical A or B cinema ports use the SMPTE 292M bit serial interface standard and will auto detect cinema source formats shown in Table 4 1 Table 4 1 Compatible Formats for Cinema Source Orig Format Vert Freq Scan Type Display Format Progressive Standard SMPTE 274M 1998 NOTE Uses 1125 total klines per frame SMPTE 274 1920 x 1080 60 Hz Interlaced 1920 x 1080 24 Hz 1920 x 1080 59 94 Hz Interlaced 1920 x 1080 23 98 Hz 1920 x 1080 50 Hz Interlaced 1920 x 1080 25 Hz 1920 x 1080 30 Hz Progressive 1920 x 1080 30 Hz 1920 x 1080 29 97 Hz Progressive 1920 x 1080 29 97 Hz 1920 x 1080 25 Hz Progressive 1920 x 1080 25 Hz 1920 x 1080 24 Hz Progressive 1920 x 1080 24 Hz 1920 x 1080 23 98 Hz Progressive 1920 x 1080 23 98 Hz SMPTE RP211 2000 SMPTE RP 211 1920 x 1080 30 Hz Prog Segmented Frame 1920 x 1080 30 Hz 1920 x 1080 29 97 Hz Prog
137. d and protected from unauthorized changes In rare cases serial and or Ethernet links are needed only by the installer and are disconnected afterwards Connect up to a total of five Ethernet links to the 5 port hub within the pedestal which in turn connects to the Communication and Source Connection Panel at the underside of the projection head For serial communica tions always connect to the RS 232 A port on this panel RS 232 B uses Christie proprietary protocol intended for Christie accessories only Connect serial links to RS 232A only This panel is located on the underside of the projection head near the front Access from within pedestal RS 232 A 000o RS 232 B z EE j ETHERNET o O090009000000000 o eooooooooacoogoo GPIO enescees onaceees OCleseseeeem O a m Cinema Server Figure 2 27 Communication Links with Projector 2 18 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 2 4 TPC Connect the TPC cable to the Ethernet hub within the pedestal this is usually pre connected from factory PC Laptop Server or Network To communicate with the CP2000 SB from a computer server or an existing network connect the equipment to the Ethernet hub within the pedestal If Ethernet is not available at your site connect a standard
138. dd masks for scope e Open masks for flat pe SENS emt 7 85 screens TE Top bottom masking 2S9 ERE to hide screen edges lM FE 1 85 image Masking moved aside S Figure 4 4 Top Masking for Scope Alternatively masks may be installed at each side of the screen in order to change the width of the screen but not its height Figure 4 5 e Add masks for flat e Open masks for scope In some cases a theatre has both side and top bottom masking installed This arrangement is the most flexible of all 1 SVEN emia Wasim 2 39 screens Side masking to hide screen edges 71 m 1 85 image A 2 39 image Masking moved aside Figure 4 5 Side Masking for Flat Refer to Table 4 2 for a summary of the basic factors affecting cinema displays in a variety of theatres CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction Table 4 2 Basic Ways to Achieve Flat amp Scope Displays al 4 ev 1 03 201 CP2000 SB User Manu 020 100162 06 R HGGH CYLL LOVON 10 nue doy wi a ue ieee z K Wooz Fl aur OAV Wea a xosdde 002i lt 0871 J4LVYJHL SNDISVYAdOL peite Doissemluno4 ous peu 990108 0021 SULVaHL ONDISVA 30Is Wld lt adoos MNO OWLL OU ITY S1 Xld OUR IIV edALenwou 4 6 CHY IS TIE Se
139. ded during installation 3 Any user beyond the General User can also choose from the complete range of test patterns offered in the password protected Advanced menu START FEATURES or PRESENTATIONS To start a different feature or presentation press its correspond ing display button STATUS BUTTON Color indicators Green All OK Yellow Environment Diagnostics WARNING Red Environment Diagnostics CRITICAL ERROR Flashing ALARM CONDITION CP2000 SB User Manual 3 11 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 3 5 2 TPC Status Menu NOTE The Status System menu described here is available to all users For information about the password protected Status Server Status Diag and Status Interrogator menus refer to Section 3 11 Working with Servers and Diagnostics Navigate the Status menu as you would Windows Explorer or File Manager expanding or compressing directories as desired by pressing the corresponding small square buttons To see more of the Status menu drag the scroll bar up or down This menu updates approximately every 30 seconds A sample view of the Status System menu is shown in Figure 3 6 amp INFORMATION INDICATORS As shown in Figure 3 6 this blue symbol identifies basic informative data describing the source connection as well as certain non critical historical operational facts about the projector and lamp Such data does not trigger warnings or error conditions ENVIRONME
140. ded for regaining the desired color performance called Target Color Gamut Data and essentially compensates for the type of port window if present screen lens light output ambient light and other current environmental factors that affect color performance Results are defined in a file activated and downloaded to projector memory to be used as a basis for all future displays If there are changes to the environment in the future for example a new screen is installed the CP2000 should be re calibrated Also note that correction for proper color balance sometimes reduces overall light output NOTE Most gamut functions are also now available in the TPC Gamut menu password required Multiple MCGD files can be saved for use in different situations such as when an auxiliary lens is swapped on and off the projector Electronic Screen Masking DCP Librarian also provides a powerful masking tool for precision cropping of the image to correct for geometry problems such as a keystoned image The effect is similar to aperture plate filing typically done for correcting images from film projectors As in the calibration of color screen masking adjustments are global that is you can create a variety masks and download them to projector memory for use with sources as desired Mask settings are distinct from aspect ratio or screen position settings NOTE Most screen functions are also now available in the TPC Screen menu password required PC
141. dssasessstoradvenssncedoskndens desansssabiaearenancincabateianiense 3 51 Bi Errors and ARIUS sneins EA E ews 3 51 3 6 Remote Control of the Touch Panel Controller cccecccceseeesceeseeceeceeeeeeeeeeseeceaeenseeeeeeeeseees 3 52 3 6 1 Understanding ASCII Message Formats xicccevinvcdsstenenntssndecevtacasiesccdelecsineaeaneee 3 52 3 6 2 Message Components and Structure essssessesseeseesseesreseessttstsrtsstesstsrrssressessessressessrssees 3 52 3 6 3 Sample Messages and Their Meaning essssessessessesssesseeseesseesrsresseessesersstessessrssressessrssees 3 53 3 6 4 What is Actually Sent in a IMGSSIG 6 2060 nscpssucasacuScnesivedonainyionssitoasseesdocnpsenesibndeeantanctedes 3 54 3 6 5 Available ASCII Codes 5 sanskocsnnecsaiesvettecesuneaccaveaeavesncteatuscsledecenanncaeiseutacmseanpeturnetlacenntinasioeats 3 54 3 6 6 Set p a d UA acs ce eda tccasn escwpa pnadeneats ieasaudnacasasneaacaqubntecadtnaeexeadeaecesananeauananenannians 3 54 3 7 Upgrading SSM TA A ccs sic auueceecd connie wnat a ee cutee een naan ahaa vc ances ea rene 3 55 3 71 RRQUALETINGING lt ccaceu success ieni E sos EE E E Gens E E RE E Rien E RE 3 55 3 1 2 Update Proceed S 5 cosscsasivassysananccubexslicees gosssenencsestomsncasediacesmleoeceiessesbanessenbensdedseasunesaeaneee 3 55 3 7 3 Troubleshooting sesei A EEE EE EERE 3 56 3 8 Working with th Lamps sseniacisnsara iiia Rr E AN EV SENE TE 3 57 3 8 1 Turning the Lamp ON OFF os cnnzdssccsecveasesnanaetanedactesns
142. duction 2 9 Fold Mirror and Convergence Adjustments In rare instances shipping and handling may affect the precise factory alignments of one or more optical components as a final step of installation the installer may have to adjust the fold mirror and or convergence of the DMDs as described here Fold Mirror Adjustment If a corner or edge of the image is missing this may indicate that the fold mirror has become misaligned with the rest of the optical system resulting in cropping of data Correct as described below Remove the fold mirror access plate from the underside of the projection head this plate is located just below the lens Two access holes will be revealed through which you can adjust two fold mirror screws To raise or lower the image adjust the screw closest to the operator s side e To move the image left or right adjust the screw furthest from the operator s side 3mm hex driver lt i Image a O Figure 2 45 Fold Mirror Adjustment DMD Convergence A convergence problem is evident when one or more projected colors red green blue appears misaligned when examined with a proper convergence test pattern where normally the 3 colors should overlap precisely to form pure white lines throughout the image one or more poorly converged individual colors may appear adjacent to some or all of the lines Qualified service technicians can correct as described on the color label provided in
143. e Lens 3 10 Working with 3D 3 11 Working with Servers and Diagnostics CP2000 SB User Manual 3 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction 3 1 CHRISTIE Projector Basics 3 1 1 Components and Features 3 2 The main CP2000 SB components appear in Figure 3 1 and are briefly described below in alphabetical order NOTE heat Ss extractor required Primary Lens Mount Auxiliary Mtg Bracket opi Primary Lens Air Filter Breaker Panel Door Main AC fo ballast liquid coole Ethernet hub and TPC Projector for main lectronies only not lamp Internal for Aux power Source amp Communication Connection Panel internal Power Cable 6 wire 3 phase with sep single phase OR 5 wire 3 phase incl neutral OR Leveling j _S D _ 4 wire 3 phase only Feet Route for external source and or control cabling High Securlty Lock Exhaust Touch Panel Controller TPC Lamp Door medium security lock Security Plates Or Internal Rack mount PEDESTAL Equipment Coolant Level Gauge AN Extender Legs internal Locks each side medium security Removable Casters 4 kk iod aceurity standard High sceuity optional Figure 3 1 Basic Projector and Related Components CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction Air Filter
144. e is assigned for this source only NAM text Assign name to the current channel 256 characters max NAM sl text Assigns a name to channel 1 NAM 80 text Assigns the same name to all channels Channel Selection CHA CHA Selects between 1 16 channels on the TPC Value range 101 132 CHA What is the current channel CHA S101 Reply from proj that new channel is 101 first channel Range 101 132 Color Space Selection CSP CSP P7v2 Set the color space gamut or TCGD to P7v2 CSP What color space is currently in use CSP P7v2 The P7v2 color space is currently in use CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction Function Code Examples Description and Parameters Data Format DTF DTF Selects the source type and packing mode for the current input Cinema source A or B 0x00 4 2 2 unpacked 10 bits color default 0x01 4 2 2 packed 12 bits color 0x02 4 4 4 unpacked 10 bits color 0x03 4 4 4 packed 12 bits color Cinema dual link A and B 0x00 4 2 2 packed 10 bits color with O E pixels default 0x01 4 2 2 packed 10 bits color with O E lines 0x02 4 2 2 packed 12 bits color with O E lines 0x03 4 2 2 packed 12 bits color with O E pixels 0x04 4 4 4 unpacked 10 bits 0x05 4 4 4 packed 10 bits color mixed 0x06 4 4 4 packed 10 bits color O
145. e or shock hazards NOTE Only qualified service technicians are permitted to open any enclosure on the product and only if AC has been fully disconnected at BOTH wall breakers Warning SHOCK HAZARD Disconnect from AC before opening any enclosure Disconnect at BOTH wall breakers Lamp Precautions Any Xenon arc lamp used in the CP2000 SB is under high pressure and must be handled with great care at all times Lamps may explode if dropped or mishandled WEAR PROTECTIVE CLOTHING Never open the lamp door unless you are wearing authorized protective clothing such as that included in a Christie Protective Clothing Safety Kit P N 598900 095 Recommended protective clothing includes but may not be limited to protective gloves latex lab gloves double layer 0 040 acetate face shield and a quilted ballistic nylon jacket or a welder s jacket Warning 1 EXPLOSION HAZARD Wear authorized protective clothing whenever the lamp door is open 2 Never attempt to remove the lamp directly after use The lamp is under increased pressure when hot and may explode causing personal injury and or property damage Allow to cool completely NOTES 1 Christie s protective clothing recommendations are subject to change 2 Any local or federal specifications take precedence over Christie recommendations COOL THE LAMP COMPLETELY The arc lamp operates at a very high pressure that increases with temperature Failure to allow the lamp to sufficiently cool pri
146. eckbox is cleared LPI What is the current LiteLOC setting for this channel LPI s101 What is the LiteLOC setting for Channel 101 LP1 12345 The current LiteLOC setting is 12345 CP2000 SB User Manual B 7 020 100162 06 Rev 1 03 2014 Section 1 Introduction Function Code Examples Description and Parameters LampLOC Module LLM CHRISTIE LLM000 000 0158 Single Parameter 1 Calibrate stepper motors 2 Automatic Lamp alignment LampLOC Multiple Parameter P1 0 move motor P2 0 1 2 specifies either x y or z motor respectively P3 Destination new motor position 200 up to 200 Lamp Message Enable LME LME 0 LME 1 Enables or disables a lamp timer message when the lamp has exceeded its expected life 0 No lamp message will appear when lamp limit expires 1 Lamp message will appear when lamp limit expires Lamp Mode LPM 2 Constant power 3 Constant light intensity LiteLOC mode NOTES 1 Specify desired channel with S Ifno S parameter is included the LPM setting will apply to the current channel when the Lamp Per Channel checkbox is enabled and to all channels when the checkbox is cleared 2 Specify global parameter with G LPM S101 2 Changes mode for channel 101 to constant power LPM G Requests global power mode LPM G 002 LPM S101 Reply to global power mode request Request for Ch
147. ed 1 Select the Projector button and enter a checkmark in the Change Config checkbox This will enable editing of the Projector Ethernet Configuration text boxes 2 Enter the projector s new valid and unique IP Address desired The last octet can be any value from 10 99 3 Enter the projector s new Subnet Mask address settings required 4 Select the Apply button to implement the new address settings in the projector A caution will remind you that the address must be unique and valid for the site if you are unsure cancel and consult again with the network Define Network Must match TPC settings IP Address mrt eos feo lt i Defines projector Subnet Mask Figure 3 34 Change Projector s IP Address administrator Otherwise click OK to finish NOTE The new projector address will also be implemented in the Admin General menu so that the TPC will look for this projector when you have finished setting up all network changes CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 Default Gateway 192 fies 206 i Not usea 3 45 Section 1 Introduction CHY IS TIE 3 46 5 When a new address is implemented in the projector another dialogue box will remind you that if your settings moved the projector to a different network most common the TPC will no longer be able to control the projector Ignore any Cancel buttons that may appear in this dialogue box You must therefore immediately change the
148. ed Operators Advanced Users Administrators and Installer In addition to the basic user rights shown in the Any User above the TPC offers four distinct password protected levels of use shown in shaded areas in Figure 3 4 Each has all of the rights of lower levels plus additional rights as described below Trained Operators can access the New Lamp function required when replacing the lamp Advanced users can access two additional menus Custom and Advanced where they can define all display setups and set the DVI processing path configure 3D displays optimize light output record lamp changes activate test patterns and set certain system preferences Administrators can also use five Admin submenus Source Screen Gamut IP Config and GPIO to define setup files as selectable choices for processing a variety of incoming signals Source files set incom ing resolution offset rare and desired final aspect ratio Screen files determine image cropping masking size of display area and type of lens and color Gamut information ensures color display standards are prop erly met in the current environment In the IP Config menu the administrator can define new Ethernet set tings IP network addresses for the projection head and TPC In the GPIO menu the administrator can select pre defined GPI or GPO macros e Installers and other Service Personnel can access two additional configuration menus General and Lamp as well as three more S
149. eeswureccansateaauscedixianandvacsstarontensaumiarsiutieunnaee 2 3 21 3 Exba st DUCTNS s sssvidessalaccinieicntasnsenadedons EE E A maausenianeasasantsnnnsanisenendesantians 2 11 DV E CS A E E EE E E EEE 2 12 Prim ry Zoomi LENS saiet ni ieena EE E E EEE E a AEE EEEE ERE E 2 12 Anamorphic Lens or 1 26x Wide Converter Installation Optional ccceeceeteeeeeeeee 2 12 2 1 5 Install First We AMM os ccciieessavasiwascsnaieveusur tana enne scares acwannegsens eassannenmnnvnscagtas Snee TAERE ER LEERE E T ROETES 2 12 2 1 6 Co necting to POWE sessioner E E ER E 2 13 2 2 Installing and Connecting Sources ssssssseessesssssrsssensessocssensorsetsseasonssrssrnsseseessresonssesseessensessets 2 16 2 2 1 Support for Internal Servers Source sicsssascacsiasssscisehenrdess isasesaveceassudssactsoauancennsisadasaonatsesiuiass 2 18 2 2 2 Security for Internal Servers SouUrce sessseessesersseesseserssressessesseessensesseessensonsersseesonsorsseeos 2 18 2 3 Connecting for Communications ye isscedsacssinesedanaasatenenswncssuntsnoateansndensdaneandngeasinendensedeaningenacdeatannnss 2 18 TPC cdinetecucriien E R EE ee eee 2 19 PC Laptop Server or Network czsciccscaiscaranenassiovesaaseceanenscivensbaeversnadesenstacsnansoncsvactiacesuuretarenss 2 19 2 4 Adjusting Tilt and Leveling cscsssscacsssccssanpdcsealadccatatancivhoisiectanseeasasiatarsatanaseisiecamsoamaniasaianes 2 19 2 95 Initial Power UDisroreieroe sirri ene E EEE T EEE E E ERa 2 21 2
150. electing a Display Starting a Presentation NOTES 1 For manual operation i e non automated 2 In order to use the TPC software originally shipped with the projector the installer typically connects a laptop and uses Christie s DCP Librarian setup software to download all necessary configuration files to the projector for use at the TPC To change to a new source i e a new presentation or display do the following 1 Ensure the CP2000 SB and TPC are both powered up and operating normally 2 On the Touch Panel Controller TPC select the Main menu tab 3 On either of the Main menu pages press the desired display button the image will update accordingly Refer to Figure 3 39 NOTES 1 Depending on your expected needs your installer may or may not have configured all sixteen buttons for use 2 Buttons may have any icon and or text Main Status Custom Advanced Admin About Diag l IN 1998x1080 6 2048x858 Flat x Z Scope XYZ A 1998x1080 W 2048x858 E Flat P3 Scope P3 1 Select pre defined source large button Ha Reserved sA Reserved ax 2 Image will change PCF Flat PCF Scope Zp 1920x1038 vn 1920x804 F Flat P3 Scope P3 CH 1 8 To additional sources __ Figure 3 39 Source Selection on Main Menu sample What Happens When a Button is Selected For any display button on the two page Main menu the projector interprets incoming signal data according to one of s
151. ema display is jittery or blinking erratically ensure that the source is properly connected and of adequate quality for detection With a poor quality or improperly connected source the projector will repeatedly attempt to display an image however briefly 2 The horizontal or vertical scan frequency of the input signal may be out of range for the projector Refer to Section 8 Specifications for scan frequency ranges 3 The sync signal may be inadequate Correct the source problem The Display is Faint 1 Brightness and or contrast may be set too low 2 The source may be double terminated Ensure the source is terminated only once 3 The source if non video may need sync tip clamping The Upper Portion of the Display is Waving Tearing or Jittering This can sometimes occur with video or VCR sources Check your source Portions of the Display are Cut Off or Wrap to the Opposite Edge Resizing may need adjustment Adjust until entire image is visible and centered The Display Appears Compressed Vertically Stretched 1 The frequency of the pixel sampling clock is incorrect for the current source 2 Sizing and positioning options may be adjusted poorly for the incoming source signal 3 Use an anamorphic lens for typical HDTV and anamorphic DVD sources that have been re sized and vertically stretched via 3rd party software CP2000 SB User Manual 7 5 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 7 6 7
152. en To correct this problem adjust the Vertical Boresight bolt to direct or aim the lens mount UP towards the top of the screen to bal ance the top bottom edges Focus Top Center b Ifthe top edge of the image fails to come into focus then the image focuses behind the screen To correct this problem direct the lens mount DOWN by adjust ing the Vertical Boresight accordingly When both sides appear equally blurry adjust the Offset by clicking the up down left right buttons on the Main Lens menu to re center the image on the screen Figure 2 43 Adjust Vertical Boresight Repeat Steps 2 5 until the top and bottom of the screen are both well focused Refocus Although all sides of the image should now be in focus the center of the image may be slightly blurry at this point Re focus the center of the image The goal is for good focus at the center and on all sides Adjust the Vertical Hold Screw to lock the lens mount in place Check boresight again See Figure 2 42 For more information on ILS and channel setups refer to Section Custom Lens Menu on page 3 26 Copy the Channel Settings To Another Channel Once the basic image alignment for a channel is complete you can copy this setting between channels From the Custom Lens menu use the drop down menu to select a particular channel and click Copy for the changes to affect the selected channel Repeat for every channel that requires the same ILS v
153. en handling Do not ingest Top up as necessary watching the gauge closely Important Whenever coolant has been added or replaced check for a possible airlock upon the next projector power up Refer back to Figure 2 33 Check Hose for Airlock problem on page 2 21 NOTE Refer to Section 3 1 Projector Basics for all cooler operating details 6 4 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 6 2 4 6 3 6 3 1 6 3 2 Exhaust Duct amp Lamp Fan Interlocks Check maintain both vane switches one in the exhaust duct and one near the lamp fan at least every 6 months Check operation as follows 1 Turn projector ON lamp is not needed 2 Turn extractor fan OFF 3 Confirm that the TPC displays an alarm window indicating that the extractor fan vane switch has failed Turn fan back on to correct 4 Block air intake at rear corner of projector head on the operator s side 5 Confirm that the TPC displays an alarm window indicating that the lamp fan vane switch has failed Clear air intake to correct Maintain vane switches as described in Section 6 3 Maintenance and Cleaning NOTE f the exhaust duct becomes significantly blocked or if a fan fails the projector s airflow sensor should trigger a shutdown before the projector becomes overheated or unsafe Regardless check the airflow periodically Maintenance and Cleaning To help ensure optimized performance and reliabi
154. entation Control File A small file created by the content owner or installer that controls the presentation of the elements and data subdivisions constituting a single version of a title The text component may identify the name of the title its owner its length event points and other attributes The PCF specifies color space target color gamut gamma a k a degamma aspect ratio and image position settings It does not include screen masking cropping information PCFs were originally intended as part of content distribution PINCUSHION A distortion of the image shape characterized by concave edges PIXEL PICTURE ELEMENT The smallest discernible element of data in a digital image PIXEL CLOCK RATE Pixel clock rate describes the speed at which incoming data is processed and is dependant on the native resolution and vertical frequency such as 1280 x 1024 x 60Hz or 2048 x 1080 x 24Hz of the incoming source The two processing paths available in the projector cinema vs non cinema offer different maximum pixel clock rates 1 0 MHz if cinema path and 165 MHz if non cinema path thus their use with DVI sources depends on the incoming resolution and vertical frequency PIXEL PHASE The phase of the pixel sampling clock relative to incoming data PIXEL TRACKING The frequency of the pixel sampling clock indicated by the number of pixels per line PLAY LIST A small file or script typically created by the exhibito
155. ently with their remote IR keypads PULL UP PULL DOWN Shifting the frequency sample rate or frame rate to as to achieve a target frequency or time relationship with another signal most commonly by 1 the ratio of NTSC to B amp W TV frame rates Refer to 3 2 Pulldown PULL DOWN LIST A selectable menu item that unfolds into a list of options pertaining to it QUVIS A manufacturer of a digital video recorder player server QuBit frequently used for providing digital cinema data QuVis image compression uses a proprietary technology called Quality Priority Encoding based on wavelets in which the user selects a quality level based on signal to noise ratio The data rate varies to efficiently maintain that quality level Frames are coded individually REAR SCREEN A translucent panel for screen projection Incident light travels through the incident surface of a rear screen and forms an image on the other surface Rarely used for cinema applications RELEASE PRINT Composite positive motion picture prints generally made from internegatives intended for distribution to exhibitors RESIZING The ability to manipulate through software commands the physical size placement and or aspect ratio of an image Also called scaling RESOLUTION The maximum number of pixels that the projector can display horizontally and vertically across an image such as 1280 x 1024 called SXGA or 2048 x 1080 RETRACE TIME HORIZONTAL The mini
156. equired From within the Admin menu an installer can access three additional submenus not available to any other user These submenus are primarily for defining critical system parameters such as the projector s IP address lamp type and user rights for remote access and data logging Installers can also record minimum and maximum footlambert readings to define a range from which other TPC lamp readings are interpolated and they can set whether Status menu temperatures appear in Celsius default or Fahrenheit A typical Admin General submenu appears below ID for projector location on net work Default E address shown Main Status Custom Advanced Admin about Use valid address for the site Bi r IP ddress Define site 192 168 206 40 h j Restrict Fon access the TPC remotely e Normal Rear i j Remote Access e No access e Inverted Front e Inverted Rear e Login required e Free Access Toggle to use a different lamp mode amp power for each channel or to use one setting for all Define the extent of data to be logged e Errors e Standard e Detailed NOTE Toggle to read Slows TPC response temp in deg C or deg F Send Alarm Window messages via Ethernet Figure 3 35 Admin General Menu Options Table 3 19 Summary of Admin General Menu Options ADMIN GENERAL MENU OPTIONS Projector IP Determines which projector the TPC controls and always terminates in 0 99 Al
157. ers Do not modify any CP wiring or lead dress during installation and ensure the added device does not interfere with normal CP operation Power normally is hard wired to the TB2 terminal block NOTE nternal power connection is not possible if incoming AC feed is 4 wire 3 phase only as the TB2 terminal has no power in this case PANEL A This panel is located on the underside of the projection head near the front Access from within pedestal RS 232 A Roae RS 232 B f ie O ETHERNET F auh 900000000000000 88 fr eooo 88 f Dl S o GPIO i a DVI 2 DVI Figure 2 25 Connecting an Internal Cinema Server Source This panel is located on the underside of the projection head near the front Access from within pedestal PANEL A RS 232 A n A ose o RS 232 B p ZA hI ETHERNET eos Ke eee F Lez 2 i E AE EEA 5 RH o SU GAs map ooodon li o GEE wo ES oooocdo0ec00000 62 gt RH AA x S NN 2 aN A N W A A 1 Figure 2 26 Connecting an Internal Non cinema DVI Source NOTE The DVI ports are single link ports for single link cable connectors only Using as a dual link pair requires a special adapter not currently available CP2000 SB User Manual 020 10
158. essing the Do Auto button in the Advanced Lamp menu Watch the gauge on this menu After 2 3 minutes the best lamp position will be established using an internal light sensor and the Do Auto button will no longer be disabled At this point light output is optimized se m00 v i a wl E E Doauto New Lamp Preference Lamp Lanp History Lens Test Pattern User Optimize lamp position and light output Figure 2 34 Align the Lamp NOTE Lamp must be on and douser shutter open during LampLOC adjustment However the projector does not need to be displaying an image Calibrating Screen Brightness fL In order for the TPC to display screen brightness in footlamberts fL you must measure screen brightness at both extremes of lamp power minimum and maximum for a given lamp type and record these two readings in the TPC Admin Lamp menu available to installers These measurements establish a range stored in memory from which the TPC can interpolate all other lamp power settings converting them to approximate footlamberts for display in the menus Repeat the calibration if you ever switch to a different lamp type size NOTE For more information about menus and footlamberts refer to Section 3 Operation CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction 2 7 Basic Image Alignment NOTE Assumes projector is fully assembled and powered up in its final location Thi
159. fails to download files properly try the WS_FTP or similar program 3 56 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CH IS TIE Section 1 Introduction 3 8 3 8 1 3 8 2 Working with the Lamp Simple software controls and adjustments can help to optimize lamp performance and ensure the brightest most uniform image possible for the life of the lamp These controls are located in the Main Advanced Preferences and Advanced Lamp menus on the TPC NOTE For individual menu functions refer to Section 3 5 Using the Touch Panel Controller TPC Turning the Lamp ON OFF Lamp ON OFF fA 1998x1080 Select and hold Flat XYZ for 1 2 second A 1998x1080 2048x858 jy Flat P3 Scope P3 Reserved U Reserved Pd PCF Flat PCF Scope fy 1920x1038 A 1920x804 Flat P3 Scope P3 Figure 3 45 Lamp Button on TPC ON With all CP breakers set to ON ignite the lamp by pressing the lamp button on the Main menu of the TPC make sure to press and hold for approximately 2 second OFF To turn the lamp OFF press the lamp button on the Main menu of the TPC make sure to press and hold for approximately 2 second Then WAIT for fans to run for 10 minutes to cool the lamp and other compo nents then turn off all breakers If the Lamp Won t Turn ON If the lamp fails to ignite the projector will automatically re try ignition using 100 of the maximum power acceptable for the lamp If this re try also fails and there
160. fer only the three general user menus intended for daily operation If you need to access additional functions offered in other menus you must log on as a specific user with more rights Press the user level icon in the bottom right corner of any screen then enter the desired user name and password in the text boxes provided OPEN OR CLOSE THE DOUSER SHUTTER To blank the display for instant picture muting and cooler stand by mode press the raised douser shutter key showing a lens that is currently projecting light Closing the douser slides a shutter blade in front of the lens and reduces lamp power to 50 of its maximum rating To open the douser and restore previous lamp power press the depressed douser key showing a darkened lens with red warning circle MOVE THE AUXILIARY LENS Toggle the current location of the optional auxiliary lens position it either in front of the primary lens to stretch the display horizontally or move it aside NOTE For complete operating instructions refer to the information supplied with the Motorized Auxiliary Lens Mount SEE TEST PATTERNS To display a test pattern press the Test Pattern button repeat to cycle through available test patterns To return to a presentation toggle the Test Pattern button again or select one of the 8 display buttons from a Main menu page NOTES 1 Allow 2 3 seconds for each test pattern to appear 2 The number and type of available test patterns depends on what the installer loa
161. ferent name Note that a new OnSite overwrites any previously defined OnSite file and will be the default reference point for all future color processing the old OnSite file cannot be recovered By default the projector will refer to OnSite data to calculate the corrections needed to achieve a known target color performance standard in the future However if the site requires more than one set of native MCGD values such as when an auxiliary lens is swapped in or out you can create a new MCGBD file with a different file name Each setup channel can then use any desired MCGD file as the basis for the color corrections needed for a target color MCGD files are chosen in the Custom menu NOTE Once created user created MCGD files can be deleted only by using Christie s licensed DCP Librarian software Important Create MCGD is a permanent over write of any previous MCGD OnSite file and will define new default color processing in the projector TARGET TCGD and CREATE TCGD NOTES Upon opening the Gamut menu the Target TCGD color fields show the corresponding x y color coordinates defined for the current target color gamut in use You can create a new custom target by defining different coordinates for one or more TCGD colors or simply by changing the tolerance state and saving as a new TCGD file Note however that industry defined TCGD standards such as P7v2 and others are write protected and cannot be changed modifications to such
162. for P1 6 7 The input number 1 8 or channel number 1 25 of CineIPM Available for P1 6 and P1 11 only The above will change the input on the selected channel only 1 16 To change the input on a different channel the source number must be used in front of the parameter that is used SIN s1 1 changes channel one input to 292B CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Function Code Examples Section 1 Introduction Description and Parameters Simple Network Management SNM requires v2 7 or higher and TPC 60 66 Used for simple network management protocol setup SNM 0 trap IP address To disable specify 0 0 0 0 SNM 1 OID OID is either 11273 or 25766 Select Source Format SRF SRF filename Select the stored source file defining incoming resolution and desired aspect ratio for the current display SRF SRF 1280x1024square What is the current source format Current source format filename is 1280x1024square Shutter Control SHU SHU 0 SHU 1 Source Change SRC Open or close the electronic quick douser 0 shutter open 1 shutter closed Same as CHA command Stop TI Communication Terminate TPC Application STP 0 Start TI communication 1 Stop TI communication 2 Terminate TPC application 3 Reboot TPC System Status SST Target Color Gamut TCG Method of
163. g Never attempt to remove the lamp when it is hot The lamp is under great pressure when hot and may explode causing personal injury and or property damage Allow to cool completely STEP 2 Turn Off Remaining Circuit Breakers After allowing the fans to run for at least 10 minutes turn OFF the remaining INTERNAL and PROJEC TOR circuit breakers located on the breaker panel of the projector STEP 3 Disconnect Projector from AC Supply Anhe SHOCK HAZARD Disconnect from all AC at ALL wall breakers STEP 4 Open the Lamp Door With protective clothing and shield on unlock the lamp door and open it Refer to Figure 2 5 Open Pro jector for Access on page 2 5 If desired release the latch mechanism to remove the door entirely STEP 5 Open Cooling Compartment Turn knob to open the inner lamp cooling compartment and reveal the cathode end of the lamp STEP 6 Remove the Old Lamp and Inspect Reflector a Loosen set screws from negative cathode rear 7 64 and positive anode front 3 16 lamp connec tors These screws are shown in Figure 6 2 NOTE Be sure to apply minimal torque and DO NOT STRESS the quartz tube b Carefully slip the positive anode connector off the front of the lamp c Handle the cathode end only Unscrew the lamp from the rear connector and carefully remove it from the projector Immediately place the lamp inside the protective cover saved from previous installa tion and then seal it in a heavy carton on t
164. gure 2 18 Vane Switch CP2000 SB User Manual 2 11 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 2 1 4 2 1 5 2 12 Lens es Primary Zoom Lens 1 Fully insert the lens assembly straight into the lens mount opening all the way back without turning With the lens fully back it will seat properly within the lens mount NOTE High Contrast lenses only have a flat on the rear flange Rotate the lens so that the flange clears two screws in the mount Also ensure the UP label is at the top to ensure proper aperture orientation 2 Lock the lens assembly in place with lens clamp DOWN NOTE The lens seals the projector head preventing contaminants from entering the area of main electronics Never attempt to operate the projector without a lens installed 3 Calibrate the lens See Section 2 7 Basic Image Alignment for details Anamorphic Lens or 1 26x Wide Converter Installation Optional NOTE Required only for 1 25x anamorphic lens or 1 26x wide converter lens producing 2 39 1 scope images If the anamorphic or wide converter lens will be used it is recommended that you now add the lens and its motorized mount so that the additional weight will be present when correcting later for final leveling and boresight adjustments Install only for those installations requiring full size 2 39 1 scope images mostly side masking screens 1 INSTALL THE AUXILIARY LENS MOUNT ON THE PROJECTOR At the front of the pr
165. he TPC s Custom 3D Control menu are identified in Figure D 1 NOTES 1 Pins not shown in Figure D 1 are reserved for other uses and cannot be specified at the TPC 2 Cable access is through the pedestal toe at front Connection Panel RS 232 A o 0000 gt af opo ii Gi ete 333 3 aan 2 LS 3 o p B DVI 2 DVI 1 GPIO Port INPUTS D viewed from underside QUTPUTS GPI 1 Pini Pin20 Pini GPO 1 Ping Pin28 GPI 2 Pin2 Pin21 GPO 2 Pin 10 Pin 29 GPI 3 Pin3 Pin22 GPO 3 Pin11 Pin30 GPI 4 Pin4 Pin23 I GPO 4 Pin 12 Pin31 GPI 45 Pin5 Pin24 Pin37 GPO 5 Pin13 Pin 32 GPI 6 Pin Pin25 GPO 6 Pin 14 Pin33 GPI 7 Pin7 Pin26 GPO 7 Pin 15 Pin34 GPI 8 Pin8 Pin26 Figure D 1 GPIO Connector Pinouts As shown above each available pairing of pins is defined as either an input or output 5 VDC External Supply Recommended Operating Point mA Max Current 50 mA Forward Voltage Drop 1 1 V 5 mA 4 To Center ity Pin of BNC oe B Pa To Shielding TAR of BNC IR Emitter Figure D 2 Circuit for Power Supply If you are wiring your own GPIO cable for use with a server or 3D device such as an IR emitter or a polarizer follow the circuit diagram in Figure D 2 D 1 1 Example GPIO and 3
166. he Wide Converter lens with the following High Brightness or High Con trast Zoom lenses only 1 45 1 8 1 1 8 2 4 1 2 2 3 0 1 or 3 0 4 3 1 1 FOCUS PRIMARY LENS With the auxiliary lens in place re focus the primary lens using focus knob The goal is good focus at center and on all sides 2 LENS CLEARANCE Adjust clearance between the primary and wide converter lens to match the values in the following table NOTE Measure from front of prime lens to back of wide converter lens barrel Zoom Lens Clearance 1 45 1 8 1 8 6 mm 2 1 8 2 4 1 13 6 mm 2 2 2 3 0 1 6mm 2 3 0 4 3 1 6mm 2 3 VERTICAL LENS POSITION Adjust the converter lens vertically so that it is exactly on the center line with the pre adjusted prime lens 4 HORIZONTAL LENS POSITION Adjust the converter lens horizontally so that it is exactly on the center line with the pre adjusted prime lens 5 PITCH ADJUSTMENT Adjust the top and bottom clearance between the wide converter and prime lenses until they are equal using a wedge gauge or small calipers 6 YAW ADJUSTMENT Adjust the two side clearances between the wide converter and prime lenses until they are equal using a wedge gauge or small calipers 7 RECORD SERIAL NUMBER Enter the serial number of your converter lens in Advanced Lens menu Refer to Figure 3 20 Advanced Lens Menu Options on page 3 31 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Intro
167. he floor where it cannot fall or be bumped Warning Han dle box with extreme caution The lamp is hazardous even when packaged Dispose of lamp box according to safety regulations for your area d With the lamp removed visually inspect the reflector for dust Clean if necessary as described in Sec tion 6 3 Maintenance and Cleaning CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction STEP 7 Remove New Lamp from Protective Cover a Remove tape knurled nut and locking star washer if present securing the lamp within its cover b Handling at the ends only extract the lamp from the cover Set aside the protective cover for re use in your next lamp disposal or for warranty return of an expired lamp STEP 8 Install New Lamp a With protective clothing and shield on install the new lamp by inserting the threaded cathode end of the lamp into the negative lamp connector nut located in the rear of the lamp compartment and screw in fully Figure 6 1 left Hand tighten only Caution Handle by the cathode anode end shafts only never the glass Do not over tighten Do not stress the glass b Rest the anode end of the lamp on the lamp cradle Figure 6 1 and slip the positive lamp connec tor over the bulb end Do not stress quartz Screw bulb Into connector Figure 6 1 Install Bulb c Hand tighten set screws in both negative E AATA and positive lamp c
168. he non unicode requires only 1 byte See example in Figure 3 41 which illustrates a picture mute is off reply from the projector asci L P L 2 o o o NON UNICODE HEX 0x28 Ox4c 0x50 0x28 0x21 0x32 0x30 0x30 0x30 0x29 Ss Ss UNICODE HEX oxno ox28 0x00 0x4 0x00 0x50 0x00 0x28 0x00 0x21 0x00 0x32 0x00 030 0x00 oxa0 0x00 0x30 Figure 3 41 ASCII as Non unicode and Unicode NOTE Use of unicode or non unicode in messages is auto detected from the TPC Available ASCII Codes All available ASCII message codes including those with multiple parameters are listed and explained in _ Appendix B ASCII Messages Setup and Shutdown SETUP 1 Inthe Admin General menu define which users all none or some have remote access rights 2 Open an Ethernet socket to the TPC address socket 5000 By default the TPC address is 192 168 206 110 If you have additional TPCs the installer should have defined their addresses as 192 168 206 111 192 168 206 112 and so on or used other addresses that are valid for your site 3 Communication protocol should now be established and can be confirmed with a PNG if desired NOTE The socket will automatically close after 15 minutes of inactivity Program your controller to send a PNG message every 5 10 minutes to maintain communication and keep the socket functioning Important 7o prevent sh
169. head are protected by an electronically monitored high security lock on the lid This interlock strictly controls access since every opening ofthe lid is 1 electronically logged and reported and 2 will immediately disable the current CineLink 2 cinema presentation The unlocked state is reported via a TPC alarm window serial communication and SNMP note the latter requires the TPC 60 model of the Touch Panel Controller new in 2006 You must lock the lid in order to remove the key and activate the switch for normal operation The two identical keys provided at manufacture are unique to your projection head serial number as identified on the back of the Christie key fob and cannot be duplicated If you lose or damage a key contact your dealer or Christie for a new security lock and key set the keys cannot be replaced individually NOTE Jt is recommended that all keys to the projector be kept in a locked cabinet at the site Other CP panels are not removable with standard tools or they can be removed only where there are other obstacles in place that prevent theft or tampering Security Plates The rear security plates help prevent unauthorized access to the interior of the pedestal They remain in place until equipment such as servers or PCs is rack mounted within the pedestal After rack mounting your equipment ensure to re install the pair of vertical rack protector posts at the rear They will overlap the sides of your new equipme
170. iag Menu CHRISTIE The Status Diag menu provides status information about projector components and the current cinema source and enables log files for each device to be saved to the TPC s storage card for diagnostics Info about projector components Clear SMPTE errors Useful for Write SMPTE log to TPC s storage card directory Write projector log or self test log to TPC s storage card testing if the 9 y directory L Senje oeg er O F Figure 3 61 Status Diag Menu Options Test every projector component NOTE Do not use during a show SMPTE log of source server errors Reboot and per form a Self Test 3 11 3 TPC Status Interrogator Menu The password protected Status Interrogator screen enables the collection of advanced level status information that can assist in the diagnostics of projector components Interrogator can be run in two modes and enables the collection of log files only BASIC MODE or log files plus registered batch files ENHANCED MODE These files are then stored on the TPC s storage card For Interrogator to successfully retrieve these diagnostic files the projector must remain in its failed state with incorrectly displayed image on screen NOTES 1 Always run Interrogator first before power cycling the projector otherwise important diagnostic files will be unusable 2 Never run Interrogator during a show as this could cause image disruption 3 In
171. ically Auxiliary lenses install in the auxiliary adapter optional and are used in conjunction with a primary lens 8 3 Inputs 8 3 1 Cinema Inputs Number of inputs 2 Standard supported SMPTE 292M bit serial Connector Type BNC NOTE Currently supported cinema formats are listed in Table 4 1 on page 2 8 3 2 Non Cinema DVI Inputs for Alternative Content Number of inputs 2 Standard supported VESA Digital Visual Interface DVI D Connector Type 24 pin female DVI D NOTE Currently supported DVI formats i e non cinema formats are listed in Table 5 1 on page 2 8 3 3 Control Ports RS 232 connectors 2 9 pin D female A Non ASCII PC communication B Christie propri etary accessories only Ethernet connector 1 RJ 45 female Stnd 100 base TX 100 Mbps max GPIO connector 1 37 pin D female Ballast Control Port 1 9 pin D male nota RS 232 w proprietary protocol user port Ballast Interlock Port 1 9 pin D female not 5V TTL compatible opto isolated at ballast end a user port CP2000 SB User Manual 8 3 020 100162 06 Rev 1 03 2014 Section 1 Introduction 8 4 Touch Panel Controller 8 5 8 4 Type of Display Integrated Operating System Communication Interface w CP Power Requirement Current Rating Interface Connector Memory Power Specifications Projection Head 5 7 diag color LCD backlit Microsoft Windows CE 10BaseT Ethernet 0 05 A max at 24 VDC 10 2 0 A max 8 pin
172. icates whether an option is currently in effect checked or not unchecked CHROMINANCE The signal representing the color information hue and saturation when the image is represented as separate chrominance and luminance Same as chroma CLEAN APERTURE The fraction of a motion picture frame image that is intended to be viewed by the audience The clean aperture is subjectively free of edge artifacts and lies within the screen area framed by curtains in a cinema Aspect ratio is often referenced to the clean aperture COLOR GAMUT The range of colors allowed in a specific system as defined within a triangular area located on the CIE color locus diagram whose corners are the three primaries defined in the system Also known as color space COLOR SHIFT A change in the tint of a white field across an image COLOR TEMPERATURE The coloration reddish white bluish greenish etc of white in an image measured using the Kelvin degrees K temperature scale Higher temperatures output more light COMPONENT VIDEO Refer to _YcbCr or YPbPr A 4 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHX 1S TIE i Section 1 Introduction COMPOSITE VIDEO The output of video tape players and some computers characterized by synchronization luminance and color signals combined on one output cable CONTRAST RATIO The degree of difference between the lightest and darkest areas of the image CONVERGENCE The alignment of the
173. ilter and fan Prism is too hot Power down and cool projector Reduce lamp power Ami Check air filter and sensor Check liquid cooler fan bient temperature may be too high Integrator is too hot Red DMD is too hot Blue DMD is too hot Power down and cool projector Reduce lamp power Ami Check air filter and sensor Check liquid cooler fan Power down and cool projector Reduce lamp power Ami Check fluid flow and level Check air filter Check liquid Power down and cool projector Reduce lamp power Am Check fluid flow and level Check air filter Check liquid bient temperature may be too high bient temperature may be too high cooler fan bient temperature may be too high cooler fan SSM is too hot Power down and cool projector Reduce lamp power Ami Check fluid flow and level Check air filter bient temperature may be too high Ballast is too hot and has shut down Cool then cycle the projector down and up normally If the over temp recurs there is a cooling problem in the ballast that may require service Check bal last fan OTHER FANS TOO SLOW A primary fan is too slow or stopped Replacement fan may be required Card cage fan is too slow or stopped Replacement fan may be required Laminar airflow is too slow or stopped Replacement LAD filter or fan may be required LAMP PROBLEMS Lamp Life has expired Unexpected lamp OFF Replacement
174. ing manual adjustment 4 In case of emergency unplug the line cord to immediately halt movement of the lens mount Adjust Offset Main Status Custom Advanced admin About Die Project an image with the primary lens only Always adjust offset before boresight Important Ensure the E B correct lens is selected in the Advanced Lens menu before calibration to ensure you will remain within the B applicable boundary of the installed lens NOTE When E E adjusting the Focus Offset and Zoom you may experience a slight delay in the response rate of the lens upon selecting the buttons 1 Ensure Auto ILS is selected from the Main Lens menu NOTE Enabling Auto ILS will over write the pre defined settings for this channel To perform a temporary lens adjustment uncheck Auto ILS and adjust the lens by clicking the necessary buttons or Figure 2 37 Intelligent Lens System manually adjusting the focus offset and or zoom knobs All temporary adjustments will be lost when Auto ILS is selected again or if the channel changes CH 1 8 CH 9 16 CH 17 24 CH 25 32 2 Using an framing test pattern Framing tga is recommended adjust the Offset by clicking the up down left right buttons on the Main Lens menu Figure 2 37 as necessary to display a square image on the screen NOTES 1 You can also hold the buttons down for continuous movement 2 For best optical performance make sure to minimize keystone error by using offse
175. irect the lens mount towards the RIGHT by adjusting the Horizontal Boresight accordingly AERIAL VIEW NZ Projector Figure 2 41 Aerial View Illustrating Misaligned Boresight Focused 5 When both sides appear equally blurry adjust the Offset by clicking the up down left right buttons on the Main Lens menu to re center the image on the screen Repeat Steps 1 5 until both sides of the image are well focused 7 Adjust the Horizontal Hold Screw to lock adjustments in place Check boresight again See Figure 2 39 2 26 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CH IS TIE i Section 1 Introduction 2 8 3 Adjust Top Bottom Boresight 2 8 4 When the horizontal boresight is complete focus the image at the top edge of the screen l 2 3 8 Loosen the Vertical Hold Screw See Figure 2 42 Extend the lens focus completely Adjust the Focus to retract the lens using the down arrow on the Main Lens menu Watch the image at the top edge of the screen until it comes into focus If the image appears well focused on the top edge but not on the bottom adjust the Vertical Boresight If the entire screen come into focus skip to step 8 Vertical Boresight Bolt Vertical Hold Screw Continue retracting the lens Figure 2 42 Vertical Boresight a Ifthe bottom edge of the image comes into focus before the lens is completely retracted then the image focuses in front of the scre
176. ited to the location and accessibility of hazardous voltages Read and understand all written procedures prior to commencing a service procedure CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction Understand and follow all local safety codes and requirements when servicing energized live equipment Perform equipment service in a location free of obstructions and other hazards For example you must have an unobstructed view of the area being serviced e Wear personal protective equipment PPE clothing appropriate to the service you are performing This includes but is not limited to protective electrically insulated footwear safety glasses and gloves rated for the working voltage of the equipment you are servicing 2 1 2 Projection Head and Pedestal STEP 1 Secure Projection Head to Pedestal a Roll the pedestal as close as possible to its permanent location with its front toe facing the port win dow wall b Inside the pedestal at the rear of the top frame turn the knob to extend the safety prop above the ped estal frame This stop will then elevate the rear of the projection head until fingers are safely out of the way See Figure 2 1 Step 1 With head In place secure 4 rods Ay o G La 3a wrench Figure 2 1 Assembling Projection Head with Pedestal c Lift the projection head onto the pedestal aligning the four threaded rod
177. ixteen user selectable display setups defined at the time of CP2000 SB installation and or with each subsequent release of a new digital cinema feature and stored in projector memory Each display setup consists of Projector Configuration File PCF information as well as additional processing display parameters and screen settings optimized for a particular cinema feature or alternative content source For proper processing and display of a source press pre assigned display button see Figure 3 39 corresponding to the setup you wish to use the button will then appear recessed and the projected image will update according to the display setup assigned to this button No further adjustment of the image should be necessary To change to a different presentation select a different display button 3 50 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction Cinema Vs Non Cinema Sources Typically the display setups for digital cinema servers are carefully configured when the projector is installed so that presentations will be automatically optimized and require no further adjustment A user need only select the relevant display button Displays of non cinema or other alternative content such graphics or video sources connected to DVI ports are also usually pre configured for easy selection Refer to Section 5 Non Cinema Operation for details about non cinema applications and display adjustments Other Methods of
178. jector s 2048 x 1080 display and remaining data is ignored You may have to experiment with the values to accurately zoom in on a precise area and you must also define offset see below if you want to zoom in on an area other than the center CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE OFFSET NOTES Offsetting an image is achieved by defining how much horizontal width and vertical height to discard Offset coordinates can be particularly useful when zooming in on a portion of the image they establish the top left corner location of the zoom area with Resolution above determining the size of the area Leave offset at 0 default to process all incoming data or to zoom in at the center of the image or set to a positive or negative Offset 450 value as described y ee a ia Section 1 Introduction e A positive x y value discards image data from top and or left e A negative x y value discards image data from bottom and or right Figure 3 25 Offset Differences ASPECT RATIO NOTES Table 3 15 lists the sixteen most common source setups which are selectable from the Main menu pages In the event your source material is pre scaled or compressed enter the desired aspect ratio Adding the 1 25x anamorphic or 1 26x wide converter lens will widen a squeezed image back to its original scope aspect ratio For sources that are not pre squeezed aspect ratio can be left at 0 Table 3 15 Pre configured
179. l four values octets Address must be valid for your site For example perhaps you can use the default 192 168 206 0 to control a single projector installation Then use 192 168 206 to control a second projector at that site 19 a ae to control a third projector and so on NOTE This menu does NOT define the projec tor s address Image Orientation Define the orientation of the screen relative to the projector Celsius Display Choose Celsius or Fahrenheit temperature display for Status menu Remote Access Define whether all users can access TPC functions remotely or not at all or whether a login is required Data Logging Define the extent of activity to record in an Ethernet accessible TPC data log default Errors only A good data log can be helpful when troubleshooting but use with caution detailed logging will slow TPC responses Note that when the memory card becomes full logging continues and simply writes over the oldest entries Error Message When enabled an error message will be sent via Ethernet whenever an alarm condition is encountered Enabled CP2000 SB User Manual 3 47 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHRISTIE Admin Lamp Menu Record light measured for both extremes of power Select to automatically reduce lamp power to its minimum e Measured at screen e Projector will be able to inter polate future light output in foot lamberts Select to aut
180. lant reservoir ensure the hose between the reservoir to the pump is completely full upon the next power up Figure 2 33 NOTE f the hose is not full this signifies the presence of an airlock that can interfere with proper circulation of the liquid throughout the projector Turn the projector OFF then ON once again The hose should now be completely filled Check at first power up z reservolr after reservoir has been SIRE filled or topped up O S55 Figure 2 33 Check Hose for Airlock STEP 5 Check Fans and Interlocks Check that fans are running and interlocks are OK CP2000 SB User Manual 2 21 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH IS TIE j 2 6 2 6 1 2 22 STEP 6 Define the Lamp Type At the TPC go to the Advanced Lamp menu password required Enter the size of the lamp currently installed in the projector default is 2 0 kW STEP 7 Ignite the Lamp At the main menu of the TPC press the LAMP button 9 The lamp should ignite Maximizing Light Output Upon powering up the projector with a newly installed replaced lamp activate LampLOC to automatically adjusts the lamp position to help ensure optimized operation as well as peak brightness at the screen You do not need an image displayed yet Once you have done this LampLOC adjustment the lamp will be well centered and distanced correctly from the remainder of the illumination system At the TPC automatically optimize lamp position by pr
181. led The five scenarios are explained below For any installation always follow the electrical code for your country Warning 1 Certified electrician required Follow the Terminal Block 1 TB1 Connections diagram located on the inside of the pedestal 2 Installation of the pedestals conduit panel is MANDATORY to avoid risk of electric shock causing bodily harm or even DEATH 1 From the AC power source route the 3 phase wires single phase and ground wires into one of the knock out holes located on the pedestal s conduit panel Use appropriately sized strain relief connectors with the conduit panel This will ensure adequate environmental sealing and prevent cables from wear and being accidentally torn out Warning Use of the conduit panel is mandatory to prevent electric shock 2 Connect the incoming AC ground lead directly to the frame ground stud on the floor of the pedestal Figure 2 20 Secure with both washers and nut provided and ensure there are no other wires present at this stud Warning Connect ground FIRST to reduce shock hazard from high leakage round Stud Nut e AAA aN Zz Ss of om Le e Ground Lug From AC Supply Ground Connection Ground Lug Figure 2 20 Connect Incoming Ground Wire 3 Refer to the Terminal Block 1 TB1 Connections diagram provided on the inside of the pedestal door operator s side As described for your model and site connect all available wi
182. les back and forth via FTP PC files appear in the left window TPC files appear on the right For this update to take effect you will be required to replace the SSM HEX file located on the TPC ISPM directory Right Window in FFFTP with the new SSM HEX file 1 Run FFFTP ona PC that is connected to the same network as the TPC At the main window click the Connect icon or File Connect menu The Host List box should appear Figure 3 42 FFFTP File Commands Bookmarks Yiew Tools Options Help siete aie al nll lela Ells yl is D epuninst exe 2004 02 11 13 29 66 237 exe C FFFTP exe 2003 0510 11 19 344 064 exe 2003 0510 13 54 i 2003 05 10 13 55 D JRE32 dli 1997 06 11 2 54 FFFTP Ver 1 92 Copyright C 1997 2003 Sota Local Selected 0 0 Bytes Local free 839 10M Bytes Files in queue 0 Figure 3 42 Main FTTP Window with Host List CP2000 SB User Manual 3 55 020 100162 06 Rev 1 03 2014 2 8 3 7 3 From the Host List of FTP servers click the TPC FTP server and then Connect Or if using FFFTP for the CHRISTIE Section 1 Introduction first time click New Host to create a new connection to the FTP Server The Host Setting dialog box should now appear Complete the Host Setting entries Figure 3 43 Profile Name name desired for TPC Host Name Address TPC IP default address is 192 168 206 110 use the unique and valid address defined for your site e Username TPC user name
183. lity regularly check electrical optical and other components as described below Warning SHOCK HAZARD Disconnect from AC at BOTH wall breakers Electrical Do the following every 60 days or 500 hours always disconnecting from AC first e Check the contact surfaces of positive anode and cathode negative connections for cleanliness e Clean electrical contact surfaces as necessary to prevent contact resistance from scorching connectors e Verify that all electrical and lamp connections are tight Optical Unnecessary cleaning of optics can be more harmful than helpful increasing the risk of degrading delicate coatings and surfaces In this projector check only the ens and lamp reflector maintenance of other optical components requires a qualified service technician Check these components periodically in a clean dust free environment using a high intensity light source or flashlight Clean them only when dust dirt oil or other marks are obvious Never touch an optical surface with your bare hand always wear latex lab gloves When to Check LENS A small amount of dust or dirt on the lens has minimal effect on image quality to avoid the risk of scratching the lens clean the lens only if absolutely required See below LAMP REFLECTOR Inspect the mirror surface reflector for cleanliness only during a lamp replacement when the lamp is out If necessary clean as described below ensure to wear protective clothing while inspecting
184. ly 14 F1 press the Set button to automati cally enable LiteLOC The current brightness level will be maintained as long as possible NOTE Arbitrary units of measure appear here not footlamberts or lumens Lamp Power Indicates what percentage of power appropriate for the installed lamp to supply to the lamp automat ically overriding any LiteLOC setting that may be in effect This causes the bar graph to rise or fall The LiteLOC line and Set values will not change unless Set is clicked defining a new LiteLOC setting Refer to Table 8 1 Minimum and Maximum Lamp Power by Lamp Type on page 8 6 for lamp power ranges LampLOC LampLOC buttons activate motors that reposition the bulb in the projector for optimized light out put Use the Do Auto button recommended or the individual buttons NOTES 1 Lamp must be ON to begin If it is turned OFF during a re positioning the bulb will return to its former position 2 Douser opens and remains non functional during a LampLOC adjustment Lamp read only Indicates the current lamp age amps current volts voltage and watts lamp power Read only CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 New Lamp Activates the lamp history window and text editing box for recording a new lamp s serial number which resets the lamp timer Light Level Indicates current light output shown as solid vertical bar and LiteLOC level set single horizont
185. mes use 1 12 characters User Level Upon entering the User menu this box displays the rights of the current login read only These rights determine which TPC menus and functions are available The User Level tracks with different user names in the box above When adding a user User Levels can be chosen from in a pull down list note that only those levels with rights that are equal to or lesser than those of the current login will appear Password Enter a new 1 8 character password for the current login or when adding a new user Non editable at other times Confirm PW Re enter the 1 8 character password entered in Password box Editable when changing the current password or when adding a user Change PW Change the password for the current login Change Level Change the rights for a different user having the same or fewer rights as the current login Add User Activates the editing box for defining a new user their rights and password You cannot define more rights than your own Delete User Delete a different user who has the same or fewer rights as the current login and who is cur rently displayed in the User Name box The current login user cannot be deleted Cancel Escape to the original User Menu without saving changes Save Record current User Menu settings in TPC memory CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 3 33 Section 1 Introduction CH IS TIE TO ADD A NEW USER 1 Press Add User 2 Enter desi
186. mounted directly in the rear of the CP They must not interfere with CP operation Regardless of their mounting location sources must connect to one of four ports on the Communication and Source Connection Panel located on the underside of the projection head They are typically connected as part of projector installation Once made these connections are inaccessible from the outside of a locked projector and can be considered secure and permanent Changing or adding a source connection requires access via the locked CP pedestal NOTE 7o maintain radiated emissions compliance do not connect 1 0 cables to the projector without connecting the source or receiver at the other end IF EXTERNAL Source server cabling routes through the pedestal toe and up to the underside of the projection head Limit cable length to 300 feet or less Connect power externally or within the projector See Figure 2 23 and Figure 2 24 shown are models with internal outlet for North America etc NOTE The DVI ports shown in Figure 2 24 are single link ports for single link cable connectors only Connect two independent sources or connect the Cine IPM 2K to both ports for 10 bit processing Using this pair of ports as a dual link pair requires a special adapter not available This panel is located on the underside of the projection head near the front Access from within pedestal PANEL A RS 232 A oone RS 232 B booo O ETHERNET a o GOODS OCOSOODGO g o0g0g
187. mp lamp type and Tgnition Difficulty or LPC reason for change of the newly installed lamp thus resetting the 60123456 100 CDXL 20 3 lamp time to 0 for logging time Serial number 32 characters max Valid Lamp Types CDXL 20 CDXL 30 CDXL 45 CDXL 60 CXL 20 CXL 30 CXL 45 CXL 60 Other 16 Etc Valid Change Reason can be sent as number or text o 1 Usage Hours Exceeded 2 Light Level too Low 3 Ignition Difficulty 4 Light Unstable flicker 5 Was Temporary Lamp 6 Lamp Type Change 7 Other Lamp History HIS HIS 021 00001 1234567 00007 2007 Lamp history describes lamps used in the projector See Messages 08 01 15 58 Other 20 00000 00000 With Multiple Parameters in this Appendix 00000 000 Usage Hours Exceeded Lamp Hours of Use LPH LPH 0528 The hours logged on the current lamp 0 9999 Lamp Hours Limit LPL LPL 750 The hours that a lamp can be used before a warning message appears Range 0 20000 hours Lamp Intensity LPI LPI 12345 The light output level chosen for LiteLOC Same intensity for every channel requires LPB Lamp Per Button set to OFF NOTE Specify desired channel with S Ifno S parameter is included the LPI setting will apply to the current channel when the Lamp Per Channel checkbox is enabled and to all channels when the ch
188. mum time required for a CRT projector to move the position of the scanning spot from the right edge to the left edge CP2000 SB User Manual A 11 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH ISTIE i RGB VIDEO The video output analog or digital of most computers Analog RGB video can have 3 4 or 5 wires one each for red green and blue and either none one or two for sync For three wire RGB the green wire usually provides sync Refer to_TTL Video RS 232 A common asynchronous data transmission standard recommended by the Electronics Industries Association EIA Also called serial communication RS 422 A less common asynchronous data transmission standard in which balanced differential voltage is specified RS 422 is especially suited to long distances S VIDEO The output from certain video tape players and video equipment S Video separates sync and luminance from color information typically producing a higher quality display than composite video Also known as Y C SCAN FREQUENCY The horizontal or vertical frequency at which images are generated Also known as scan rate or refresh rate SCAN LINE One horizontal line on the display SECAM A video output format of some video tape and disk players used primarily in France SECAM Sequential Couleur M moire signals are similar in resolution and frequency to PAL signals The primary difference between the two standards is in the way color information is
189. n Zoom Click the buttons to automatically minimize or maximize zoom Copy Lens Settings Use the drop down menu to select a particular channel and click Copy for the changes to affect the to Channel selected channel Repeat for every channel that requires the same ILS values 3 26 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CH IS TIE i Section 1 Introduction Channel Lens Menu Disabled The Channel Lens menu is grayed out when the Auto ILS feature of the Main Lens menu is not selected See Figure 3 15 In the instance that an ILS is not installed on the projector or if the Installed option in the Intelligent Lens System region on the Advanced Lens menu is not selected the Custom Lens menu will not display Figure 3 15 Custom Lens Menu Disabled 3 5 5 TPC Advanced Menu All password protected requires Installer Admin or Advanced User rights except for the New Lamp button accessible by Operator login The TPC Advanced menu consists of six different submenus Preference Lamp Lamp History Lens Test Patterns and User that enable installers administrators and advanced users to define numerous system operating parameters load and or display test patterns work with lamp settings and set up users and their TPC access rights CP2000 SB User Manual 3 27 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHRISTIE Advanced Preference Menu As shown below the Preference menu provides
190. n Disabling alarm triggers is not recommended for normal operation Failed interlocks an SSM communication fault rc fault and lamp failures always produce an alarm window i e these alarm triggers cannot be disabled or hidden CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Responding to an Alarm Window Section 1 Introduction Press the acknowledge button in order to hide the alarm window and access other TPC menus and try to solve the problem as shown in the right column of Table 3 2 Table 3 2 Alarm Conditions and Solutions FAILED INTERLOCK Lamp door is open Make sure the lamp door is securely shut Failed lamp fan Check for interference at vane switch Ensure the 220V connection near Panel C at the rear of the projector head on the underside is still plugged in Replace fan Failed heat extractor for external duct at the top of the projector May not be turned on 600 CFM required Replacement heat extractor may be required Failed auxiliary interlock usually for fire alarms or automation systems Check auxiliary switch wiring in pedestal Check the external controlling device Failed high security lock cinema use disabled Lock the projector lid If still failed double check the high security lock itself plus all related harnessing OVER TEMPERATURE Card cage is too hot Power down and cool projector Ambient temperature may be too high Check air f
191. nal Ethernet hub and the 24V power supply If desired you can mount the TPC and its 24V power supply else where at the site Route the TPC cable through either the rear or front hole on the projector Cap the unused hole Figure 2 4 Typical TPC Mounting 2 4 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE STEP 5 Connect Pre Installed Cabling Pedestal to Head Numerous cables are pre installed within the pedestal and must be routed up to the underside of the projec tion head where they connect to one of three panels or two IEC power sockets Connect pedestal to head cabling as follows Section 1 Introduction NOTE For all cable connections keep cable ties that have been trimmed at manufacture but remove temporary ties that are untrimmed and have tails a Open both pedestal doors Figure 2 5 b Open the rear side door on the operator s side c SET BALLAST AC INPUT SWITCH Before connecting the ballast to AC set the ballast s AC input switch to match the AC available at the site Toggle left for nominal 200 VAC supplies and toggle right for 400 VAC supplies The factory default is 200 VAC d BALLAST RS 232 CABLE Connect the ballast s RS 232 cable 34 002075 to Panel B 9 pin routing through the small rectangular access hole in the front underside Open pedestal doors of the projection head Figure 2 6 Figure 2 5 Open Projector for Access
192. nal color cube Linear _9x9x9 v for increased color accuracy Define frame offset OnSite x Field 1 v Select field offset polarity Page 1 Page 2 3D Control 15 19 53 Figure 3 10 Custom Page 2 Menu Options Table 3 5 Summary of Custom Page 2 Menu Options CUSTOM PAGE 2 MENU OPTIONS Auxiliary Lens In Sets whether or not the optional auxiliary lens is used with this channel Pull Down Re Sync This command is used to enable or disable the re synchronization function associated with the Pull Down Sequence It is sometimes useful to disable the re synchronization function when the time code is not running at the proper rate such as when a jog control is being used with a tape machine Screen Identifies sets display area masking cropping and expected lens for the current source Choices are pre defined using DCP Librarian or the TPC Admin menus Screen settings are not included in a PCF Measured Color For a given channel source select the desired MCGD file representing native uncorrected col ors to use as a reference for calculating target color processing Default OnSite See also Admin Gamut menu LUT CLUT Complex Look up Table No information available Pull Down Sequence Identifies sets the frame sequence to achieve a target frequency or time relationship with another signal Pull Down Offset Identifies sets the frame offset SMPTE Field
193. nates for the current TCGD to increase or decrease this tolerance area or to change its shape or location larger boxes relax the tolerance reducing the loss of light caused by precise matching Non theatre P7V2 telecine White point will be matched exactly Theatre P7V2 theatre White point match is more relaxed Clear the checkbox if the projector s whites must precisely match the target white point typical for telecine use defined for the current TCGD If this match can be anywhere within the tolerance box typical for theatre use enter a checkmark The checkbox status is saved with Figure 3 31 White Tolerance the TCGD Keep in mind that some light is usually discarded for an exact match resulting in a dimmer image it is recommended that you enable the tolerance box for all applications requiring maximum brightness such as in theatres Do not enable the tolerance box if exact color performance is more crucial than overall image brightness such as in telecine applications RESTORE NOTES This button enables you to return to the Gamut menu settings that were present when you opened the menu however the precise behavior depends on whether you are working with measured MCGD or target TCGD settings To Restore MCGD Settings The Restore button is disabled unless you have used the Test button To cancel new MCGD settings and return to the previous MCGD settings the new settings must be tested via Test button but n
194. ndling Do not ingest For this first filling fill the reservoir completely Virtually all of this first supply of liquid will be drained into the hoses upon initial power up at which point the reservoir must be re filled to the correct level at the gauge window Refer to Section 2 5 Initial Power Up STEP 8 Check Lead Dressing amp Hoses a At this point integral pedestal to head cabling and hose connection should be complete Check all lead dressing and secure as neatly as possible to prevent extra cable lengths from dangling or touching other components Provide proper strain relief as necessary Ensure hoses are free of kinks and sharp turns NOTE The capacity ofthe P reservoir is approximately i Qo Ve that of the cooling system a Figure 2 16 Fill Reservoir b Connect sources and communication links at any time Refer to Section 2 2 Installing and Connecting Sources and Section 2 3 Connecting for Communications CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 2 1 3 Exhaust Ducting Warm exhaust air from the CP2000 SB must vent to outside of the building Connect pre installed outside venting ductwork via 8 inside diameter fireproof ducting material attached to the projector s top exit port Confirm that 1 there are no obstructions or kinks within the ducting 2 all air intake areas of the CP2000 SB are clear and exposed and 3 the vane switch at the exit duct is mo
195. nePalette for deep film like blacks and superior colorimetry CineCanvas for flexible telecine grade resizing subtitling and other text and graphic overlays Two SMPTE 292M cinema inputs used individually or simultaneously for high speed dual link process ing and each supporting CineLink 2 local link encryption Dual DVI Digital Visual Interface connectors for alternative non cinema content used individually or simultaneously for high speed dual link processing Screen brightness Up to 14 fL on 90 ft screen Achievable contrast ratio 450 1 ANSI 2100 1 full field on off in center e LampLOC motorized lamp alignment automatic or custom bulb positioning LiteLOC for maintaining brightness over time Simple single button Start Feature function via Touch Panel Controller Auto detection of a variety of SMPTE 292M input formats incoming interlaced formats require proper 3 2 or 2 2 pull down time code Internal douser shutter for quick picture muting and cool stand by mode Bit depth of 45 bits 35 2 trillion colors e New ruggedized lens mount that accepts the new High Brightness HB lenses as well as previously avail able High Contrast HC lenses Choice of High Brightness and High Contrast zoom lenses from 1 25 1 up to 8 5 1 Optional Motorized Auxiliary Lens Mount for 1 25x anamorphic or 1 26x wide converter lenses CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Intr
196. nno N oe an ee hae cen eae eae 3 30 Advanced Lamp History Menu ss sessseessesesseessessessresstrseesresseeseesersseeseesessreseserssresseserssees 3 30 Advanced Lens Menu ecrire n a e A A A AE RE EEAS 3 31 Advanced Vest Pattern Men ssteissi orsica i a a E 3 32 Advanced User Men sssrin ia A E AE AR EE 3 33 3 3 6 TPC Admin Menu 5 sro esssceccncaeseslodesiensh nda RE RAEE EAE enemas 3 35 Admin S urce Men lt ca ccoiscaetiy vecausesesawabscansnenaceseerectsanvaceusehenavenatouseosauyeastnsatanseceamtecateumraeavenss 3 35 Admin Screen Menu sesrosntacnsiner raa n R EEA 3 38 Admin Gamut MENU sssssrcsmcnoip eede a n E AARE AR ETE ERE EEEE E TENE 3 40 Admin IP Confia Ment sscsacessdevnsevendtacennsinadesadanncusnnevneessidacenackaetised E E EERE 3 44 Admin General and Admin Lamp Menus sstisessssuscesdsssvcnseiuspavvsaavntssserncnssuestensssuamtistvunses 3 47 Admin GPIO Menu ssissecisesisresissinnresiinienntksoisrooiiatoaae t reared inaa sa ron araa ra TEE Aa ASTRE ES 3 48 33 1 TPC About Men s sser nan nra R ERE E ees 3 49 3 5 8 Understanding Versions in Your Projector ccecceecceesseesseceeceeeeeeseeeseecsseceeeseeeenseecsaeenes 3 49 3 5 9 Selecting a Display Starting a Presentation ss sssssssseseesseesseseesseesseserssessessessressessrssres 3 50 Cinema Vs Non Cin ema SB OULCES sapresncesaetsccpevanesdouscnesaseveshacioieeedwinnpetseouesbienssameseunuaiiiwsies 3 51 Other Methods of Source Selection osicc cous vaccse
197. nnot be struck the TPC lamp button will be disabled until the inter lock problem is resolved An alarm window will also appear on the TPC e If the lamp fails to ignite even though the interlock system is OK the projector will automatically re try igni tion using 100 of the maximum power acceptable for the installed lamp If this re try also fails a new lamp is likely needed NOTE For complete power up troubleshooting refer to Section 7 Troubleshooting CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 3 3 Power down Procedure 1 At the TPC press the lamp button on Main menu to turn the lamp OFF You must hold the button down briefly 2 Wait at least 10 minutes so that fans continue to cool the lamp Warning Be sure to wait for the cooling fans 3 At the operator s side of the pedestal set all breakers to OFF NOTE Manual shut down only Optional automation not yet available from Christie A 1998x1080 TA 2048x858 Dag Lamp OFF Flat sY zZ Scope ave 1998x1080 WA 2048x858 g Flat P3 Scope PS A Reserved UA Reserved ax Await 10 min PCF Flat PCF Scope fA 1920x1038 A 1920x804 T Flat P3 Scope P3 CH 1 3 CH 17 24 CH 25 32 Lens 15 17 00 Figure 3 3 Power down Procedure CP2000 SB User Manual 3 7 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH IS TIE i 3 4 3 4 1 3 8 Introd
198. notecstavscdeiusisceadvndesenvstevarsartsonnives 3 4 Leveling cee ec ievnc vara rece se te A EE EE Ge oe ee EAE a 3 4 Pedestal ives coisa encce vane esien ie ncn wena es cd as moe EARE E rm 3 4 Power Cabling oi cies tees wera guts ns cavemen een ea reee EERE E ree A OaE S EEEE oE aS ERE EEEE ER AEREE 3 5 Projection Hedd eeii e AE A EEE E E E 3 5 PS CUI LOCKS nirede Tr EEA AE E RERE EERO AAEE 3 5 Security Plates eis ani E a e ERE E AEE EEA E E e EE 3 5 Source Control Gabling scsssnannieinnnersier r EE A A A TE 3 6 Touch Panel Controller TPC ccsersisdeacaineteassnsodescansacaaevandsaettadeetessncsacadaadeneussubeacadaaiantanates 3 6 32 Powe r p Proce Ure jaa siseecarrsdeeaceeatouenccnied aaa eee Rees 3 6 3 3 POW EEG W i PLO COCR ES wu ca ccsazanecaysamisesaatsnns sanuastennsnesedmaubsadacuansssurcitenasviandswamaptcheremeanmmsccenopines 3 7 3 4 Introduction to the Touch Panel Controller 0 0 ccc ceccecccceseeesceesseceeeeseeeeeceeseecaeceeeseeeeeaeeeaeen 3 8 34 1 User ACCESS and IG WIS seca scenisstscetusncaversnadya cssvatresascabaisenvaatosavhadii vost vuieabiadneolenaaiouesedugeniess 3 8 3 4 2 TPG Power up Defaults ce cacecsuins ccxnsneacucesevecenaneesiwncdessiesaneacucereneesnnmnratoounaiceams aenneoanls 3 9 3 4 3 Failed TPG Onna ct Gils nataiacesdecessienacassetuccsdeateceseatacesaeaenuae gas iiae EN 3 9 3 5 Using the Touch Panel Controller IPC isvcccivenssasanesanacevanceecinueedindsennsntansnenncunnsotenuntiaessauveaeunnass 3 10 39A TPC
199. ns travel from their origin BIT DEPTH The total number of bits available to represent each pixel or color sample in a digital imaging system Using linear binary coding the total number of resolution steps available is equal to 2 raised to the power of the bit depth BLANKING TIME The time inside one scan line during which video is not generated The blanking time of the input signal must be equal to or greater than the retrace time of the projector BRIGHTNESS In cinema projection brightness usually describes the amount of light emitted from a surface such as a screen It is measured in footlamberts or candelas per square meter CP2000 SB User Manual A 3 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHX ISTIE j CANDELA OR CANDLE Unit of measure for measuring intensity of light in certain types of projectors CHANNEL A collection of measurements stored by the projector for a given input source including frequencies pulse width polarity syncs channel number and location user adjustable display settings etc Use channels to switch between a variety of setups quickly automatically recalling previously defined display parameters CHANNEL LIST A list menu of previously defined channels available in projector memory CHANNEL NUMBER A number that uniquely identifies a specific channel retained in projector memory The projector via its TPC offers up to 8 channel choices at once CHECKBOX A menu item that ind
200. nsisting of both left and right data is not currently supported e Sync Output Device IR emitter for controlling the L R gating switching of active glasses OR e Pi Cell polarizer for controlling a screen that has a silver polarization preserving surface for use with passive glasses e Custom 3D Sync Output Cable GPIO such as available from RealD For routing the projector s output sync to your Sync Output Device connect from the projector s GPIO Accessed from within the pedestal refer to Section 2 Installation amp Setup to the emitter or polarizer NOTE Refer to_Appendix D GPIO System Integration for GPIO pinouts and other 3D sync cable details CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction e Power supply for your Sync Output Device typically wired with the custom GPIO cable e Proper 3D configuration defined in the TPC s Custom 3D Control menu For best results use the 3D inter nal test pattern shown in Figure 3 58 3 10 3 Supported Hardware Setup Figure 3 56 shows the general hardware configuration currently supported Use either an IR emitter to control gating in active glasses or a polarizing cell and Z screen with passive glasses NOTES 1 A configurations require a custom 3D Sync Cable such as supplied by RealD for the GPIO port 2 A pull up power supply not shown is also required for the IR emitter or polarizing cell 3 See D 1 The GPIO Port on page D 2 f
201. nt and help prevent 1 access to the pedestal interior and 2 theft of rack mounted equipment NOTE Keep on hand any extra security plates removed for rack mounted equipment these covers must be re installed if the equipment is removed from the projector in the future Do not operate the CP with open slots at the rear CP2000 SB User Manual 3 5 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 3 2 3 6 Source Control Cabling The pedestal toe knock outs provide safe routing for all external cabling that connects to the underside of the projector head during installation Use a route not currently occupied by the main AC power cable Touch Panel Controller TPC The Touch Panel Controller TPC is a portable touch sensitive screen used to control the projector At the TPC general users can turn the lamp ON OFF select a specific source input as defined in one of 32 display setups created by the installer and obtain basic status information Depending on the installation the TPC module may be mounted to the rear of the projector with its cable routed to the projector via a rear hole or it may be mounted elsewhere at the site and routed to the projector via a front hole Tilt turn the TPC as desired for best viewing angle Navigation and complete description of the TPC menus including password protected options for advanced users or service technicians is fully explained in Section 3 5 Using the Touch Panel Con
202. o Projector Hours i Total Lamp Hours aA Lamp be Current od Voltage i Power s 75 0 v es e Preference Lamp Lamp History J Lens Test Pattern J user Figure 3 52 Lamp Hours 3 62 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction 3 8 7 When to Replace the Lamp Assuming the Lamp Expiry Message checkbox has been enabled in the Advanced Preferences menu recommended an expiry message will appear on the TPC as an alarm window when the lamp has reached its defined Lamp Limit and should be replaced Lamps should also be replaced when one of the following events occur e Lamps are no longer able to maintain SMPTE specified light levels e Image quality is compromised by excessive flicker Lamp hours have exceeded expected average life Regardless of the Lamp Limit chosen never exceed the lamp lifetime by the hours shown in Table 3 24 as an old lamp becomes increasingly fragile and more prone to sudden failure or even explosion which can be damaging and dangerous Table 3 24 When to Replace Your Lamp Lamp kW Replace BEFORE 2 0 3500 hours 3 0 2500 hours 4 5 900 hours 6 0 1000 hours 6 0SD 700 hours NOTE Hours shown here are greater than or equal to the pro rated credit warrantied lifetimes refer to Section 8 Specifications Do not exceed Refer to Section 6 4 Replacing the Lamp amp Filter for instructions 3 8 8 Maintaining Footlamberts
203. o bolts 7 Remove the jack 8 Ifnecessary re adjust all leveling feet for side to side leveling Figure 2 29 Note that you may have to adjust level more precisely once an image is present 2 20 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 2 5 Initial Power Up STEP 1 Turn on Breakers With all components installed and connected power up the projector as described in Steps 1 and 2 in Section 3 2 Power up Procedure Do not ignite the lamp yet Important Do not ignite the lamp until you have defined the lamp type in Step 6 below STEP 2 Fill Reservoir a Second Time NOTE Disconnect the projector from AC power before filling the reservoir A Upon initial power up the first supply of coolant you added will sre vines drain into the hoses and fill them leaving the reservoir practically ee empty Using Christie approved coolant Jeffcool E105 provided in the liquid coolant fill service kit P N 003 001837 02 re fill the reservoir until the level is close to but not above the top mark on the i gt gauge located on the outside of the pedestal door Figure 2 32 If Figure 2 32 Re fill and Check Level you over fill remove the reservoir from the pedestal and pour out excess STEP 3 Power Down and Up Again Turn all projector breakers OFF then ON again to clear air from lines STEP 4 Check for Airlock in Cooling System After topping up the coo
204. o create this loop connect the OUT warm and IN cool hoses as described below NOTE Hose con nections may not be labeled Be sure to depress each hose connector tab before inserting the hose end then release to seal Figure 2 15 This prevents damage caused by forcing the gasket end into a closed connector Listen for a click Depress while inserting hose end operator s side i from heat __ 0 reservoir exchanger n Figure 2 15 Connecting the Hoses b The long loose hose connected to the reservoir is the OUT warm hose from the projection head Con nect to the projection head location closest to the non operator s side of the projector c The short loose hose connected to the heat exchanger is the IN cool hose Connect to the projector head location closest to the operator s side of the projector Important 7o prevent damage to the sealing gasket always depress the connector tab when inserting the hose end Avoid forcing together and listen for click STEP 7 Fill the Reservoir Completely Initial Filling for Hosts Only NOTE Disconnect the projector from AC power before filling the reser o voir After connecting the hoses completely fill the cooler reservoir with Chris tie approved coolant Jeffcool E105 provided in the liquid coolant fill ser vice kit P N 003 001837 02 Danger HAZARDOUS SUBSTANCE The coolant used in this product contains ethylene glycol Use caution when ha
205. o not A direct to left or right and maintain at least 2 clearance from the high voltage anode connector 2 Lead dress all igniter cables AWAY from 15 pin and 9 pin connectors near the hole in the projection head floor 3 Within pedestal twist the ballast cables twice per tfoot Figure 2 9 Connect Lamp Leads IN THE LAMP COOLING COMPARTMENT 5 With the lamp door removed refer back to Figure 2 5 turn the small knob and swing open the lamp cooling compartment door Figure 2 10 Lamp Cooling j b Compartment Figure 2 10 Accessing Cathode End CP2000 SB User Manual 2 7 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 6 Route the NEGATIVE BLACK lamp lead through the hole in the cooling compartment floor Fig ure 2 11 The igniter wires from terminal 5 and the PCB are also routed here Reflector lo Duct Figure 2 11 Feed Black Lead into Compartment 7 A universal connector nut should be pre installed on the cathode end lamp post Regardless of model or lamp size this nut is 7 658 in overall Universal connector nut a all models length See right NOTE The universal nut shown accommodates all N i P all lamps models Do not install a shorter nut Important Ball joint must move i oa freely If necessary hand tighten with 9 64 Allen key 1 658 Figure 2 12 Connector Nut 8 With 3 16 Allen key secure the NEGATI
206. o sync input is at GPIO connector See L R Display Reference Notes below L R Output Polarity Keeps 3D stereo sync output the same as input true or reversed inverted See L R Output Polarity Notes below Frame Rate Ratio of total frames displayed to frames forming complete data Increase to reduce flicker in displays lt 96 Hz Max recommended setting for 2048 x 1080 displays 5 2 Can be higher in smaller displays or decreased if incoming signal is already high enough to prevent flicker See Frame Rate Notes below Input GPI Select None when 3D stereo sync input is part of source signal at ports A and B Use GPI 1 7 only if sync input is supplied to GPIO port Display GPI Always None unless 3D stereo sync input is at GPIO connector Output GPO Define your GPO sync output for 3D device glasses or z screen polarization using to 1 7 depending on wiring Dark Time Adj Create a blank time interval between L R frames to allow for glasses ON OFF Helps synchronize the output to the viewing Output Delay Time Offset in u 3D stereo sync output in relation to dark time interval Positive offset delay nega tive offset start early See Output Delay Notes below CH IS TIE Section 1 Introduction L R INPUT REFERENCE NOTES Select the option matching your source type and how the 3D sync is supplied e A LEFT B RIGHT Select if your 3D source provides separate left and right data via 2 cables at the A and B SMPTE ports This as
207. oduction 1 1 3 1 2 1 2 1 1 2 2 e Communication ports for remote control of the projector via PC or other controller High security tamper resistant lid lock with all access electronically monitored e DC2K 3D Triple Flash functionality capable of projecting full resolution 3D images under a 6 2 frame rate multiplication HDCP decryption on both DVI inputs allows display of copy protected alternate content How the Projector Works The CP2000 SB accepts a variety of cinema or DVI compatible non cinema signals for projection on front screens typical in a commercial theatre or other large screen applications High brightness light is generated by a short arc Xenon lamp then modulated by three DMD Digital Micromirror Device panels responding to incoming data streams of digitized red green or blue color information As these digital streams flow from the source light from the responding on pixels of each panel is reflected converged and then projected to the screen through one or more front lenses where all pixel reflections are superimposed in sharp full color images List of Components Ensure that you have received the following components e Pedestal on casters with 4 retractable feet installed e Projector Head with lens mount installed and auxiliary lens mount optional e Touch Panel Controller with mounting hardware e Lamp e Lens plus anamorphic or wide converter lens optional e Standard security key
208. of the lamp is recommended Increase Lamp Power Check that DMDs have not overheated An interlock may have momentarily tripped Lamp may have to be replaced Lamp strike failed If interlocks are OK ensure the 220V connection near Panel C at the rear of the projector head on the underside is still plugged in If lamp re try still fails replace the lamp CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 3 17 Section 1 Introduction CHRISTIE OTHER SSM Communication Error Check cabling Cycle projector power for a normal start up Check LEDs on card cage boards which can indicate a light engine problem instead Check LVPS Processor voltages Also if shutter or lamp are functioning normally SSM likely OK 12C Communication Error There may be a power problem with the main electronics I C Check LVPS Proc voltage adjustments LENS MOUNT A communications error with the ILS motor control board has occurred Please ensure that all cabling is correctly connected Check cabling Cycle projector power for a normal start up ILS Motor Control Board Sensor Failure This error will only be detected on a lens reset or lens calibrate Check the sensors It is cleared by cycling the projector power or performing a lens reset ILS Motor Control Board In Boot Program Mode If this message remains for longer than 4 seconds try re powering the TPC or upgrading the MCB software
209. ojector install the motorized auxiliary lens mount hardware as described in the instructions provided with the auxiliary lens mount kit 2 INSTALL THE AUXILIARY LENS Clamp the anamorphic or wide converter lens mount in place following the instructions provided with the lens mount kit For details refer to Section 2 8 5 Add Auxiliary Lens Install First Lamp Anode Connector Lamps for a complete list of supported lamps Va The CP2000 SB accommodates different lamps Refer to Section 8 6 Reflector 1 REVIEW LAMP PRE WIRING Review all lamp pre wiring as described on the previous pages ensuring that all leads and harnesses are connected correctly and that the universal cathode connector nut is secured to the rear lamp post 2 CHECK LAMP CRADLE ANODE END LOCATION FOR YOUR LAMP For 4 5 or 6 0 kW lamps the lamp cradle must be as far for pe ward as possible factory default Yar For 2 0 or 3 0 kW lamps move the cradle to the rear position Figure 2 19 Lamp Cradle Position i e approximately 1 closer to the reflector Figure 2 19 3 INSTALL LAMP Refer to Steps 7 10 from Section 6 4 Replacing the Lamp amp Filter Observe all warnings and wear protective clothing and shielding CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 2 1 6 Connecting to Power Connecting the projector to your AC supply can vary according to the country in which the projector is instal
210. omatically increase lamp power to its maximum Select to implement new values Lamp EP10 Figure 3 36 Admin Lamp Menu Options Table 3 20 Summary of Admin Lamp Menu Options ADMIN LAMP MENU OPTIONS Footlamberts Activate each text box to automatically drive the lamp at its minimum or maximum power record light Calibration measured at the screen for both extremes in power defining a range of footlamberts possible Light readings fL appearin elsewhere in TPC will then be interpolations based on this range Click SAVE to implement new values NOTE Re calibration must be done with new lamp change Admin GPIO Menu Use the Admin GPIO menu to configure GPI macros for LAMP ON OFF DOUSER OPEN CLOSE and AUXILIARY LENS IN OUT and also GPO macros for LAMP STATE DOUSER STATE AUXILIARY LENS STATE and SYSTEM HEALTH STATUS NOTES 1 Only GPIO 1 5 can be programmed 2 Use of GPIO for 3D will automatically un program any other use for that pin Status Custom GPI macro name Predefined macro Predefined macro Douser State Source Screen Gamut IP Config General Lamp Figure 3 37 Admin GPIO Menu Options 3 48 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY ISTIE i Section 1 Introduction 3 5 7 TPC About Menu The About menu lists which versions of critical components are installed in the projector As shown in Figure 3 38 this is a read only menu for all users and in
211. onnectors Figure 6 ep ee N 2 Important Proper electrical con a i tact prevents resistance in the lamp con nectors If you accidentally touch the quartz body of the lamp with your bare hands clean it as described in Section 6 3 Maintenance and Cleaning Reflector Hand tighten only Secure cathode connector P a vib Figure 6 2 Secure bulb at cathode and anode connectors 2 CP2000 SB User Manual 6 9 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE 6 10 STEP 9 Check Leads Ensure that the anode lead between lamp and igniter is well away from any projector metal such as the reflector or firewall Warning Leads too close to metal parts will cause arcing during starting pulse This is aSAFETY HAZARD and the lamp may not ignite STEP 10 Close Cooling Compartment and Lamp Door The projector will not operate unless the louvered door is locked shut STEP 11 Turn Breakers to ON At the projector s breaker panel turn all breakers to ON STEP 12 Set the Proper Lamp Type Power and Record the Serial Number of the New Lamp Important Requires access to TPC Advanced Lamp menu If your new lamp is larger or smaller than the old lamp record the new lamp type 2 0 3 0 4 5 or 6 0 kW and serial number before igniting the new lamp The new lamp type setting establishes the proper range of power available for the installed lamp ensuring th
212. operator s side of the projection head near the front See Figure 6 3 Before You Begin Read and follow all other general lamp precautions in Section 6 1 Warnings and Guidelines STEP 1 Turn Off Main AC a Allow the fans to run at least 10 minutes for cooling b At the breaker panel on the projector set the 3 phase MAIN AC circuit breaker to OFF Warning Never attempt to remove the lamp when it is hot The lamp is under great pressure when hot and may explode causing personal injury and or property damage Allow to cool completely STEP 2 Turn Off Remaining Circuit Breakers After allowing the fans to run for at least 10 minutes turn off the remaining INTERNAL and PROJEC TOR circuit breakers located on the breaker panel of the projector STEP 3 Disconnect Projector From AC Supply I ANN INe SHOCK HAZARD Disconnect from all AC at ALL wall breakers STEP 4 Open Remove Filter Door Open filter door by loosening 2 corner screws flat screwdriver and lift off door 1 and 2 in Figure 6 3 STEP 5 Replace Air Filter Slide the filter up and discard Insert the new air filter following the labeling for proper inside outside ori entation Slide all the way down into its slot 3 and 4 in Figure 6 3 Warning Use only Christie filters Never operate the projector without the filter installed STEP 6 Close Replace Filter Door With the filter in place insert the bottom tabs of the filter door into the corresponding slots
213. or Will Not Start 1 Check for green Main AC light on projector If not on check all breakers on projector and at the wall There are single phase and 3 phase breakers 2 Are the CP breakers staying on when enabled If they are tripping to OFF position there is an electrical problem requiring investigation by a certified electrician 7 2 Lamp 7 2 1 Lamp Does Not Ignite 1 Ifthe lamp button is entirely disabled not selectable at the TPC Main menu indicated by a red X on the lamp button there is an interlock failure such as an open lamp door failed lamp fan etc A flashing red alarm window also indicates this Refer back to solutions listed in Table 3 2 on page 17 2 For SSM communication failures re boot and try again 3 Ifa DMD temperature is too high DMD over critical temp limit the lamp will not ignite Cool the projector and try again 4 Ifthe Status menu indicates a ballast communication problem re boot and try again 5 Ifthe lamp does not ignite after a second try replace the lamp 6 Ifthere is no buzzing indicating that the igniter is attempting ignition there may be a problem with the igniter Christie service required 7 Ifthere is a brief buzz attempting ignition but a lamp does not ignite the lamp likely needs to be replaced 7 2 2 Lamp Suddenly Goes Off Try increasing the lamp power TPC Advanced Lamp menu The DMDs in the projection head may be overheated this also triggers an alarm window at the
214. or cabling details LW ae Active IR Emitter sA glasses N GPO SYNC 3 Or polarizing cel for Z screen and passive giasses PANEL A This panel is located on the underside of the projection head near the front Access from within pedestal R A an A a RS 232 B AN gt ETHERNET s J 3 H 333 o 000000000000000 o 69 fie one COOOGOOC00CC0D oO eee a9 5 GPIO a GO Dvi d j a oe one A shown reversed for clarity HD SDI HD SDI O fp wer ae RSS ea From Cinema Server Figure 3 56 Typical Dual Input 3D System CP2000 Shown with Active Glasses CP2000 SB User Manual 3 67 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHRISTIE 3 10 4 Other Hardware Setups Other expected hardware configurations with a single 3D source input are shown in Figure 3 57 NOTE For future reference Single 3D input is not currently supported MUIN MINI Cinema Media Server IR Emitter E GPI SYNC Or polarizing cell for Z screen passive glasses NOTE NOT CURRENTLY SUPPORTED I IU IR Emitter Or polarizing cell for Z screen passive HD SDI aiti Sync embedded with image data NOTE NOT CURRENT
215. or cleaning Note that color on the reflector surface may vary this is normal CP2000 SB User Manual 6 5 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i Supplies For cleaning off dust and or grease you will need e Soft camel hair brush Dust free blower filtered dry nitrogen blown through an anti static nozzle e Dust free lens tissue such as Melles Griot Kodak tissues 18LAB020 Optowipes 18LAB022 or Kim Wipes or equivalent e Lens cleaning solution such as Melles Griot Optics Cleaning Fluid 18LABO11 or equivalent For lens only e Methanol For reflector only e Cotton swabs with wooden stems only e Lens cleaning cloth microfibre such as Melles Griot 18LAB024 or equivalent Cleaning the Lens IF DUSTY 1 Brush most of the dust off with a camel hair brush and or blow dust away with compressed air 2 Fold a microfibre cloth smooth and gently wipe remaining dust particles off the lens Make sure to wipe evenly with the smooth portion of the cloth that has no folds or creases Do not apply pressure with your fingers use the tension in the folded cloth itself to collect the dust 3 Ifsignificant dust is still bound to the surface dampen a clean microfibre cloth with lens cleaning solution damp not dripping Wipe gently until clean IF FINGERPRINTS SMUDGES OIL 1 Brush most of the dust off with a camel hair brush and or blow dust away with compressed air 2 Rolla lens tissue around a swa
216. or to handling increases the potential for an explosion causing personal injury and or property damage After turning the lamp OFF it is crucial that you wait at least 10 minutes before turning off the rest of the projector breakers disconnecting AC and opening the lamp door This provides enough time for the internal lamp cooling fans to properly cool the lamp Cool completely before handling Again always wear protective clothing Warning 1 Never attempt to access the lamp while the lamp is on Wait at least 10 min after lamp shut off before powering down disconnecting from AC and opening the lamp door 2 SHOCK HAZARD Disconnect from AC at BOTH wall breakers before opening the lamphouse For all other precautions critical for safe removal and replacement of the lamp refer to Section 6 4 Replacing the Lamp amp Filter CP2000 SB User Manual 6 3 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHRISTIE 6 2 Maintaining Proper Cooling The CP2000 SB high intensity lamp and electronics rely on a variety of cooling components to reduce internal operating temperatures Regular checking and maintenance of the entire cooling system is critical to prevent overheating and sudden projector failure and helps to ensure reliable operation of all projector components over time 6 2 1 Ventilation Vents and louvers in the projector covers provide ventilation both for intake and exhaust Never block or cover these openings Do not install
217. orking with Servers and Diagnostics sessssessesessseessessesresseestesesseestesessreseeserssressessessees 3 71 SAM ol TPC Status Server M dance eccacteccsceeenaencvanctaeeneieeaceseuvenseusanmeatecoswneee canea ereerexeianat acest 3 71 311 2 TPG Status Diag Men assesses eccuwsaacaussesenssienduacecynnedecsvleaevs sone AA R RAE 3 72 311 3 TPC Stat s Interrogator MEU whip csutasisucsonstonsyariensesuniucentsunsaciunvsasewadiunncsasnsiseerisedsennletes 3 72 4 Cinema Operation 4 1 Compatible Cinema Sources sacaneancaeencadsacasaneancanineandeeanenesnuwivncasanedatesteiteGenunnaeanententennaiineseunees 4 2 4 2 Image Formats cia as accesses e a a R T EE 4 4 4 2 1 Projector Variables Electronic and Auxiliary Resizing 0 ccceeceeseeseeeteceeeeeeeeeeeeenaeens 4 4 4 2 2 Theatre Variables Masking ics cusshsascanasndeienaianccabesnscauepsntdedaaspecians siacsaianaupsiakcianiioulonnniess 4 5 4 3 S lectime the Cinema So rG isc dascasscrisenvarwerennecaabunediaausastoeecnvatseeathasiaisuwsdswussaedsaeinatioshanioeneds 4 7 4 3 1 Touch Panel Controller Method i isicssscassanssecsnansontevesssecssnaseceasensstnenacdancesunes stsmenssnstesiacannniys 4 7 4 3 2 Other Methods issiran ras E E EE eaeene 4 8 4 4 Adjusting the Cinema Display s cacascassacevecssncwastoonsiienssasdnenitacssewsvasansbanacensntiaeeaanteaqisearongensbamessintes 4 8 5 Non Cinema Operation 5 1 Compatible Non Cinema SOUrCES i sess cccases aocvatets Alacer salsa snaannen
218. ot yet saved If not yet tested you can either leave the menu and cancel the settings as requested by the dialogue box or attempt to save but cancel out of it If you have already saved a new OnSite file by pressing the Create MCGD button the old OnSite file cannot be restored To Restore a TCGD File Select the Restore button any time before saving CP2000 SB User Manual 3 43 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHRISTIE Admin IP Config Menu Use the IP Config menu when you need to define or change the Ethernet settings i e network address of the projector and or its TPC or if you want to configure SNMP remote monitoring NOTE Record any new settings on Section 1 4 Who Should Use This Manual of this manual DLP or TPC Configuration Choose which address to see or change Projector name Not applicable for TPC Auto assign NOTE Requires a DHCP server Enter valid and unique address for this device and site Defaults shown NOTE Gateway is cur rently non functional SNMP Configuration Access SNMP con figuration options Choose which MIB structure to retrieve Trap Object ID from default 11273 Enter specific address to send trap information 3 44 Implement current settings Enables disables text entry below Figure 3 32 Choosing DLP or TCP from Admin IP Config Menu Enables disables text entry below Implement current settings
219. ou want to limit the display area enter the desired upper left and lower right presentation coordinates or adjust with slidebars You can define a smaller rectangular area in which the left and right top corners will always share the same y coordinate as will the left and right bottom corners and the top and bottom left corners will share the same x coordinate as will the top and bottom right corners Thus upper right and lower left coordinates are not available to define the area Incoming data will then automatically resize to fill the reduced rectangular area defined by the new coordinates and any display pixels outside of this area remain off black NOTE Presently only a rectangular area can be defined as shown below A trapezoidal adjustment or electronic keystone with sloped sides is not possible 80 175 1120 175 80 951 1120 951 Figure 3 27 Screen Presentation Coordinates CROPPING NOTES Cropping is the digital equivalent of filing aperture plates in a film projector to perfect the image squareness For example if the bottom of the image appears slightly wider than the top activate the bottom left or right cropping point in the Screen menu and change the coordinates to crop or bring in the corner s of the image slightly either enter the specific coordinates or adjust with slidebars Note that thi
220. ow B 20 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction P1 P2 Notes IfP1 4 0 Touch Panel Main Indicates version detected in Versions 1 Touch Panel Language projector 2 Touch Panel Operating System 3 System Supervisor Module Main 4 System Supervisor Module Boot 5 System Supervisor Module HW 6 Ballast Interface SW 7 Ballast Interface HW 8 ILS Main 9 ILS Boot 10 ILS HW 20 Engine 21 Interface ARM Boot 22 Interface ARM Main 23 Interface FPGA 24 Interface PIC 25 Processor DSP Boot 26 Processor DSP Main 27 Processor DSP Diag 28 Processor DSP FPGA 29 Formatter Interface Hitachi 30 Formatter Interface FPGA 31 Formatter Interface PROM 34 EFIB Main 35 EFIB FPGA 36 EFIB Boot 37 EFIB Sequence 40 Formatter Red Boot 41 Formatter Red Main 42 Formatter Red Config 43 Formatter Red Gamma 44 Formatter Red Sequence 50 Formatter Green Boot 51 Formatter Green Main 52 Formatter Green Config 53 Formatter Green Gamma 54 Formatter Green Sequence 60 Formatter Blue Boot 61 Formatter Blue Main 62 Formatter Blue Config 63 Formatter Blue Gamma 64 Formatter Blue Sequence CP2000 SB User Manual B 21 020 100162 06 Rev 1 03 2014 Section 1 Introduction P1 70 FFIB Main 71 FFIB Boot
221. pecified for all four motors System Status SST The SST message provides a variety of information about the current state of the projector The single broad ranging request SST for all information triggers the return of a series of replies as if multiple requests had been sent In each of these replies P1 explains the general content or topic of that reply and P2 the individual details To obtain status for one topic only specify the desired P1 parameter corresponding to that topic for example the request SST 0 will trigger general projector information only For a specific single status inquiry include both P1 and P2 in the request for example SST 4 3 asks what version of SSM main software is installed Table B 6 System Status Messages P1 IfP1 0 0 Model General Projector 1 Serial Number Configuration 2 Build Date 4 N A 13 TPC Type P2 3 Native Resolution 5 Lamp Power Lamp Type 6 Lamp Ballast I D v 2 4c and up 7 Interface Board Serial 8 Processor Board Serial 9 Processor Board Type 10 Interface Board Type 11 Formatter Interface Type 12 Formatter Board Type 14 ILS Board Serial Number Notes CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 B 19 Section 1 Introduction CHY IS TIE P1 P2 Notes IfPl 1 0 Power Status 0 Off 1 On System Status 2 LiteLOC 0 Off 1 On 3 Lamp Expiry 4 Lamp Hours 5 Total Lamp Hours 7
222. pixel tracking phase and filter Noise is particularly common on YPbPr signals from a DVD player 2 The video input may not be terminated Make sure the video input is terminated 75 Q If it is the last connection in a loop through chain the video input should be terminated at the last source input only 3 The input signal and or signal cables carrying the input signal may be of poor quality 4 Ifthe distance between the input source device and the projector is greater than 25 feet signal amplifica tion conditioning may be required 5 Ifthe source is a VCR or off air broadcast detail may be set too high 7 6 13 There are Random Streaks on the Bottom of the Image 1 Ifa 24Hz or 25Hz HDSDI signal or a 50 Hz SDI digital PAL signal make sure to use non cinema processing delete the checkmark for Cinema checkbox in the Touch Panel Controller s Advanced menu NOTE password protected 2 Or if you do not have access to the Touch Panel Controller s Advanced menu and cannot adjust the processing path use your 3rd party input source to crop off the streaks 7 6 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE 8 Specifications Due to continuing research specifications are subject to change without notice NOTE The illustrations provided are to enhance the understanding of the written material They are graphical representations only and may not represent your exact projector model e 8 1 Display e 8 2 Lenses
223. pressed video audio and timecode stream transfer in the Profile video server products proposed for standardization by SMPTE and as a primary component of MXF Initially implemented on Fibre Channel using FTP with TCP IP but extensible to XTP or other protocols Previously called GXF General Exchange Format HDCP High bandwidth Digital Content Protection protocol of keys and encryption helps prevent DVI source material from being copied HDTV High definition Television 1035 1080 and 1125 lines interlace and 720 and 1080 line progressive formats with a 16 9 i e 1 77 aspect ratio HELP SCREEN A display of help information regarding the current task or presentation Not available in CP2000 HORIZONTAL FREQUENCY The frequency at which scan lines are generated which varies amongst sources Also called horizontal scan rate or line rate HORIZONTAL OFFSET The difference between the center of the projected image and the center of the projector lens For this projector this value is expressed as the maximum percentage of the image that can be projected to one side of the lens center without degrading the image quality HOT SPOT A circular area of a screen where the image appears brighter than elsewhere on the screen A hot spot appears along the line of sight and moves with the line of sight High gain screens and rear screens designed for slide or movie projection usually have a hot spot ILS The Intelligent Lens System des
224. r Manual 020 100162 06 Rev 1 03 2014 CH IS TIE i Section 1 Introduction AUTHORING The process tools and working environment by which content elements and functions are compiled formatted coordinated and tested for presentation on target systems Comment Authoring in the context of digital cinema does not necessarily result in inseparably married or muxed content components Rather reference is made to a virtual answer print the elements of which may subsequently be subdivided or combined encrypted in whole or part and packaged in various ways for distribution of the title a version of the title or an update for revision of the title in the field AUTOMATION A system used in a theatre projection booth that responds to cues commands or relay switches and then controls various elements of presentation such as e picture format and corresponding lens flat or scope e sound format and corresponding cinema processor settings curtain movement and position e lighting level in the auditorium e non sync play and fade in out e digital cinema projector NOTE Christies optional automation system is not yet available AUTO SOURCE The ability of the projector to automatically recognize and synchronize to the horizontal and vertical scan frequencies of an input signal for proper display BANDWIDTH The frequency range of the projector s video amplifier BAUD RATE The speed bits per second at which serial communicatio
225. r conferenc ing presented in theatres in addition to motion picture exhibition Alternative content connects to one of the projector s DVI ports AMBIENT LIGHT REJECTION The ability of a screen to reflect ambient light i e light within a room from a source other than the projector in a direction away from the line of best viewing Curved screens usually have better ambient light reflection than do flat screens ANAMORPHIC Having or requiring a linear distortion generally in the horizontal direction Anamorphic lenses restore a scope CinemaScope or flat format film frame to the correct appearance by increasing its horizontal proportion The CP2000 uses a 1 25x scope anamorphic lens option ANSI The American National Standards Institute is the organization that denotes the measurement standard for lamp brightness ANSWER PRINT A print made from the cut original camera negative with proposed final color timing and soundtracks furnished by the printing lab to the producer for acceptance of image and sound before screenings and manufacturing begin A check print is similar but is made from the internegative A blacktrack answer print has no soundtracks ASPECT RATIO The ratio of the width of an image to its height such as the 4 3 aspect ratio common in video output Can also be expressed as a decimal number such as 1 77 1 85 or 2 39 The larger the ratio or decimal the wider and less square the image A 2 CP2000 SB Use
226. r or installer that specifies the sequence of presentation of programs including features and trailers PLAYOUT The equipment in a digital cinema theatre which delivers previously recorded signals in real time to the playback system The playout may also receive store and process these signals prior to delivering them POST PRODUCTION The phase in film making that occurs primarily after production ends its processes include picture editing sound effects editing and mixing ADR Foley titles and opticals dubbing and print mastering CGI and visual effects and scoring Post production culminates in acceptance of the original negative answer print Even though post production officially begins on the last day of principal photography post production facilities such as editing are utilized from very early in the production phase in order to save time A 10 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction PRODUCTION APERTURE The area in pixels for digital images that constitutes the entire motion picture frame image Refer to Active Picture PROJECTOR TO SCREEN DISTANCE The distance between the projector s front feet centers and the screen Also called Throw Distance PROTOCOL The type of code format called A or B utilized by the remote keypad s The default protocol set at manufacture is Protocol A By using two different keypad protocols adjacent projectors can be controlled independ
227. red User Name 3 Enter a Password 4 Re enter the new password in the Confirm PW box 5 Press Save TO DELETE A USER 1 Select the desired User Name from the User Name list cannot be current login 2 Press Delete User 3 Press Save TO CHANGE A USER S RIGHTS USER LEVEL me hee Select the User Name you wish to modify cannot be current login Press Change Level button Select the new User Level desired for this user Press Save TO CHANGE YOUR PASSWORD l 2 3 4 Select Change PW button Enter the desired password Re enter the new password in the Confirm PW box Press Save WHO IS CURRENTLY LOGGED ON Enter the User Menu the User Name displayed is currently logged on 3 34 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE 3 5 6 TPC Admin Menu NOTE Password protected Administrators installers and service technicians only The seven Admin submenus offer a broad range of options used primarily for defining how the projector will respond to incoming sources in the given environment or for adjusting a major system parameter affecting overall performance Five of the Admin submenus Source Screen Gamut IP Config and GPIO are available to both administrators and installers Two others General and Lamp are restricted to installers service only See Figure 3 23 Other users cannot access Admin Admin Source Menu Incoming sources can vary widely in their current resolution and original aspe
228. res to the large terminal block TB1 located in the operator s side of the pedestal NOTES 1 The Terminal Block 1 TB1 described below accommodates up to 6 AWG wire 2 For proper torque a flat screwdriver with 4 6mm blade is recommended 3 Ensure to refer to the Terminal Block I TBI Connections diagram located in the pedestal CP2000 SB User Manual 2 13 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 180 235 VAC N America Japan most of Central South America etc e If 3 phase and single phase feeds 6 wire e Make sure ground wire is connected directly to the frame ground stud on the pedestal floor Attach no other wires here e Connect L and N 200 230 VAC single phase e Connect 1 2 and 3 180 235 VAC 3 phase o If 3 phase with neutral fed from 3 phase 5 wire e Make sure ground wire is connected directly to the frame ground stud on the pedestal floor Attach no other wires here e Connect 1 2 3 and N 180 235 VAC 3 phase e No L available Connect jumper from to L o If 3 phase only 4 wire e Make sure ground wire is connected directly to the frame ground stud on the pedestal floor Attach no other wires here e Connect 1 2 and 3 180 235 VAC 3 phase e No Lor N available so the internal outlet will not be functional 342 456 VAC Europe etc e If 3 phase and single phase feeds 6 wire e Make sure ground wire is connected directly to the frame ground stud on the
229. rily in North America and Japan NTSC 4 43 is less commonly used NON CINEMA Alternative program material such as concerts plays sporting events and potentially corporate training or conferenc ing presented in theatres in addition to motion picture exhibition A non cinema source connects to one of the projector s DVI ports NON SYNC Audio played in a theatre generally from a CD when the cinematic presentation is not running such as during intermissions and prior to the start of film presentation NON UNICODE The non unicode method of encoding produces a concise character set of 256 alpha numeric characters typically used in for ASCII messaging in most Western languages Virtually all TPC functions can be executed remotely via non unicode default or unicode messaging this is auto detected Refer to Unicode OPTICAL SCREEN A type of rear projection screen which re directs light through the screen to increase image brightness in front of the screen Screen gain is usually greater than but audience viewing angles are reduced Rarely used in cinema applications CP2000 SB User Manual A 9 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE PAL VIDEO PAL Phase Alternating Line video is a 50 Hz standard with 768 x 576 resolution It is found on some video tape and disk players used primarily in Europe China and some South American and African countries PCF Projector Configuration File or Pres
230. roach Read P1 Real time position P2 Current direction P3 Moving Status 0 not moving 1 moving Related commands are Intelligent Lens System ILS Lens Horizontal Offset LHO Focus FCS and Zoom ZOM Measured Color Gamut MCG MCG OnSite Use OnSite MCGD as the reference point for color proc MCG What MCGD is currently in use MCG OnSite Reply indicating the OnSite MCGD is in use Ping PNG PNG Request for basic projector information which includes projector type and current software version PNG 032 001 002 Reply indicating cinema projector present 32 and its current version of software is v1 2 P1 32 always indicates a cinema projector P2 Major version 0 99 P3 Minor version 0 99 B 10 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction Function Code Examples Description and Parameters Power PWR Turn the lamp projector OFF or ON 0 off 1 on PWR 0 Turn the projector lamp OFF PWR 1 Turn the projector lamp ON PWR 000 The projector lamp is OFF PWR 001 The projector lamp is ON Processing Mode PRM PRM 0 Current processing of incoming source data 0 non cinema only 1 full cinema processing path PRM What is the current processing path PRM 001 Cinema processing path is currently in effect Projector Address ADR ADR 192 168 2
231. rt of the projector and require assistance contact your dealer or one of the Christie service depots listed on the back cover of this manual In most cases servicing is performed on site If you have purchased the projector fill out the following information and keep it with your records Table 1 1 Purchase Record Dealer Dealer Phone Number Pedestal and Head Serial Numbers Purchase Date Installation Date NOTE Both serial numbers are located at the rear of the projector Table 1 2 Ethernet Settings for This Projector The following Ethernet settings were defined during installation of the CP2000 SB and the Touch Panel Controller Default Gateway DNS Server Projector Subnet Mask Touch Panel Controller Device Subnet Mask 1 4 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 1 4 1 4 1 Who Should Use This Manual USERS OPERATORS This manual is intended for trained users authorized to operate professional high brightness projection systems located in restricted areas such as projection rooms in theatres Such users may also be trained to replace the lamp and air filter but cannot install the projector or perform any other functions inside the product enclosures SERVICE Only trained and qualified Christie service technicians knowledgeable about all potential hazards associated with high voltage
232. s high security keys and assembly hardware e CP2000 SB User Manual e Refer to Figure 3 1 Basic Projector and Related Components on page 3 2 Power and Lamp Requirements POWER LEVELS The CP2000 SB offers higher power for the largest venues The CP2000 SB uses a 7 kW pedestal P N 101 101101 01 This is the only pedestal available for this model Refer to Section 8 5 Power Specifications NOTES 1 The CP2000 SB pedestal does not include an internal convenience outlet 2 All 7 kW ballasts used in CP projectors are limited by software to 6 6 kW use LAMPS The CP2000 SB accommodates different lamps Refer to Section 8 6 Lamps for a complete list of supported lamps OTHER Optional Christie components include other primary zoom lenses a motorized auxiliary lens mount and lens DCP Librarian setup software and high security locks Refer to Section 8 Specifications Software Requirements DLP version 14 series or higher TPC version 2 9 or higher CP2000 SB User Manual 1 3 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHX ISTIE i 1 3 Purchase Record and Service Contacts Whether the projector is under warranty or the warranty has expired Christie s highly trained and extensive factory and dealer service network is always available to quickly diagnose and correct projector malfunctions Complete service manuals and updates are available to service technicians for all projectors Should you encounter a problem with any pa
233. s for your area 2 Be aware that some medications are known to increase one s sensitivity to UV radiation AAIE 1 FIRE HAZARD Keep hands clothes and all combustible material away from the concentrated light beam of the lamp 2 Position all cables where they cannot contact hot surfaces or be pulled or tripped over This projector must be installed on the floor only and operated in an environment which meets the operating range specifications in Section 8 Specifications Warning Opening or removing a projector cover requires a qualified service technician CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 6 1 3 6 1 4 AC Power Precautions Installation of this projector requires that an electrician hard wire a 3 phase Y feed and a separate 15A single phase feed from the pedestal toe to the AC supply in your building You must also use only the correct pedestal for your geographic area as stated in Section 1 2 2 Software Requirements Operate the projector at the specified voltage Warning Do not attempt operation if the AC supply and pedestal are not within the specified voltage range Do not allow anything to rest on the power cord Locate the projector where the cord cannot be abused by persons walking on it or objects rolling over it Never operate the projector if the power cable appears damaged in any way Do not overload power outlets and extension cords as this can result in fir
234. s is cropping not electronic keystone adjustment In Figure 3 28 cropping simply corrects a display that overlaps the available screen If displays need cropping to match theatre screen size location In most cases cropping assumes that the entire projector display area is in use thus the coordinates initially define pixel locations on the projector s 2048 x 1080 display area Images that are significantly smaller in format may actually lie beyond the range of adjust Cropping until no one or more cropping adjustments thus you will not see evidence Bond aod sea of cropping on the edges y To correct a bowed edge so that it appears straight in the display activate one of the cropping bow points between two corner points and adjust the slidebar or enter the specific x or y value desired Figure 3 28 Simple Cropping Example CP2000 SB User Manual 3 39 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i LETTER BOX NOTES Letter Boxing ensures that all image data is displayed and its aspect ratio is maintained Use letter box for virtually all normal operation It ensures that all incoming data will be displayed within your defined presentation area and nothing will be discarded If desired any black bars unused pixels could then be cropped off using the cropping control Although disabling the letterbox control also fills the defined presentation area any extra data beyond this area whether top and bottom
235. s procedure ensures that the image reflected from the DMDs is parallel to and well centered with both the lens and screen This initial optical alignment is the foundation for optimizing images on the screen and must be completed before final boresight adjustments To save the focus offset and zoom settings to the channel you must make the adjustments using the motorized lens mount adjustment features in the Main Lens menu or Custom Lens menu from the TPC Using the knobs on the lens mount to adjust the position does not save the settings to the channel They are designed for temporary use and will therefore be lost once the channel changes Ensure the CP2000 SB is properly positioned relative to the screen before you begin Refer to Figure 2 2 and Figure 2 28 2 7 1 Basic Optical Alignment Procedure 1 Display a good test pattern appropriate for analyzing image focus and geometry such as a single crosshair centered across the image 2 COARSE FOCUS Do a quick preliminary focus and if available zoom adjustment with the primary lens only Refer to Section 3 9 Working with the Lens Do not worry about consistency across the image at this point just center focus 3 CENTER THE IMAGE IN THE LENS Holding a piece of paper at the lens surface adjust offsets as necessary until the image is centered within the lens perimeter A full white field works best for this _ gt Top Edge LEVEL Figure 2 35 Level the Top Edge 4 RE
236. s reference to a frame rate that is ofa high enough frequency to eliminate flicker as noticeable by the eye The standard frame rate for most 2D D Cinema content is 24 frames per second FPS as it is for film For 3D the server splits the 3D content video signal into 2 interleaved signals of 24 FPS each by the server for a total of 48 FPS input into the projector The projector s frame rate multiplication is set to 6 2 meaning the input frame rate is multiplied by 3 Triple for a total frame rate of 144 frames per second Hz or FPS 3 10 2 What Do I Need for 3D 3 66 The CP2000 SB requires a 3D capable SMPTE source and a few special hardware software setups described here Essentially you will connect two signals one left eye one right eye to the projector then use the TPC s Custom 3D Control menu options to define and control the signal processing synchronizing and output for devices used in your stereographic 3D display These settings ensures critical ordering and timing of the incoming L R frames so that they merge correctly into a convincing artifact free 3D display without cross talk ghosting or other artifacts System Requirements CP2000 SB projector Includes all standard 3D components FFIB FPGA Formatter Interface Board e TPC software v2 3c or higher e Main projector software v8 0 or higher e Two HD SDI cinema signals left and right connected to the projector s SMPTE ports A and B NOTE Use of a single input co
237. s to widen a Bolt squeezed image into a properly proportioned scope Figure 3 53 Anatomy of the Lens Mount anamorphic cinema display It is typically used in theatres having side masks that are retracted for scope images or in theatres having fixed side masking but a very short throw ratio throw ratio throw distance screen width To move the auxiliary lens select the Anamorphic Lens button on the Main menu of the TPC Refer to Section 2 8 Offset and Boresight Alignment for all lens installation and boresight instructions Refer to Section Custom Lens Menu on page 3 26 for ILS and channel setup Lens Mount Functions 1 If the Motorized Auxiliary Lens Mount MALM is present ensure to move the MALM to the OUT position before performing any lens ol gt calibrate or reset functions on the Motorized Primary Lens Mount to prevent collision between the projection lens and the MALM 2 Hazardous moving parts Keep fingers and other body parts away Status Custom Advanced NOTES 1 Projector must be fully assembled and powered up in its final location 2 Keep clear of rotating parts Remotely operated motors may start to spin without warning 3 Avoid CH 9 16 CH 17 24 long hair jewelry and loose clothing exposure to the knobs during manual adjustment 4 In case of emergency unplug the line cord to immediately halt movement of the lens mount 5 When adjusting the Focus Offset and Zoom you may experience a slight delay in
238. s with the four holes in the pedestal frame Warning Requires at least two people For cable connections maintain cable ties that have been trimmed and those that are not The front of the head will sit on the front of the pedes tal frame and the rear will be elevated by the safety prop d Retract the safety prop until the rear of the projection head sits on the rear of the pedestal frame All four threaded rods will be fully inserted through the holes in the top of the pedestal Secure the safety prop do not leave loose e Secure head pedestal assembly with four washers nuts tightened snugly on to the four threaded rods STEP 2 Position CP2000 SB at Port Window Roll the projector until its base is approximately 2 feet from the port window wall 3 feet if auxiliary lens mount will be added optional Center with the theatre screen lt gt if possible Figure 2 2 A If forced CP2000 SB User Manual 2 3 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i to be off center such as when a film projector is already present try to optimize aim as shown in Figure 2 2 B This will slightly increase side keystoning but will minimize required horizontal lens offset NOTE Unlike film projectors it is best to keep the projector lens surface as parallel to the screen as pos sible even if it is significantly above the screen center wear TYPICAL COMPROMISE Screen Center Ai Oft center Proje
239. sansente sei tadardetetaseoanceenelasetials 5 2 5 1 1 Du l a d Twin Link LV arsnennienineniensnans tann an EnA A aeesnnaee 5 3 5 2 S lecting the UE casas sess cescocunekcea cero veeec enc aeeti eam iea r EE En ON eta Censored 5 4 6 Maintenance Gl Warnings and Guidelines isinsin eeii en EE a RE EAEE REA boob EAEE ETRE EEREN EEES 6 2 Gels l Labels and Markings iirscssnineran ana E 6 2 6 1 2 Ge eral Precautions oss catcaceicecen ai eaGinendanaucs an ecnranconeinnaeeaccseudaxauaantcmeeren oxen taksaa aati sea askeen 6 2 Ol SAC Power PECs IONS 2 accadpaiexcatueaustncataminceaanteenieai E AEE E AEE SEARES ee 6 3 G14 Lanip Pr eCaliOns2cc ccsusincdaswonedaniwesesutavwsscseeinscy EE R ENEE E EATE AE EEEE E 6 3 6 2 Maintaining Proper Cooling oi55cccsecsscceeas sdcsasannesaseasstevansadnccundeseceasantacenesisdesasmanmeusenasiecantnauioaians 6 4 02 1 Ventilationen EER E E T S 6 4 iv CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Table of Contents AR TANE BE T EE EEE E cov EEE E A EEEE AEE EE 6 4 6 2 3 Liquid a0 e eee ee ner ree Re ee E AE E E EEN 6 4 6 2 4 Exhaust Duct amp Lamp Fan Interlocks ssincsscancasnncssnstnacannnevacvnen toeeieeviencsseateneenstnnncsstnsoeerneas 6 5 6 3 Maintenance and Cleaning sionin a a AE EEE a EERE ENE ORE ATERS 6 5 eer D E E en a eT 1 A T E E E E TE 6 5 63 Z Optica inisee en R eE EE A E EE E E ERE 6 5 When ito Check aaernenne tre een tem ener En a a A EE AEE 6 5 SUPP UES eee e sce ee a A EEE E EE AE E E
240. sdnacasecenetepanceccucentssesnennnssavecnadenanvesennents 3 57 3 8 2 If the Lamp Won t Turi ON isninnsisnninarenonen naa RE 3 57 3 8 3 Adjusting Lamp Power LiteLOC or Manually 20 0 0 cccccecccceseeeceeseeceseeneeeeeeeenseecaeenes 3 58 Using LiteLOCM aa e E EE E EE A E EEEE 3 58 Using Lamp POWER sccssssutexennensniateastssndestctoncsutdeontenenscdgcderuneddouiiincastaupnedueacueutaseatdsvepintesttuesds 3 59 3 8 4 Adjusting Lamp Position for LampLOC ssssssssssessseeseeseesseessrsersstesseserssresseserssressessessees 3 61 Use the Do Auto Button for LampLOC sssssssesssssesssessesseesseesrseesstessesersstesseserssressessessres 3 61 When to Use the Individual LampLOC Buttons sssssssssnseeseseseesseserssessessessressessessresseesesse 3 61 3 8 3 St nd by Mod sesi saacausstvccnsdandceviosdecuypdestccneduanncepsanaccsebeancuessddecsnnesncess AEA EEEE 3 62 3 8 0 How Old is My L mp rorirori eioen E a E REE O EELER E 3 62 3 8 7 When to Replace the Lampin ccsstesnstescussvevacdsecssasengaunrdusebisncrsbonantesadesaessbenatare Sanda ERR 3 63 3 8 8 Maintaining Footlamberts ycessiasiccateaccupsiidacessiiganeusotemaseiadcanenitaces ieee eae 3 63 3 9 Working with the Lens ssnssessesseesessessseeseeseesseesesessstessesersstessessesstessesstestesseestsstesseesessesstesseent 3 64 3 9 1 Lens Mount FUNCHONS sorsra naina E a N A EARNE EERTE i 3 64 VAALAN a a EEEN E E EE E N E E 3 64 CP2000 SB User Manual iii 020 100162 06 Rev 1 03 2
241. sed Rarely used in cinema CP2000 SB User Manual A 5 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHX IS TIE j DIGITAL CINEMA Professional public presentation of theatrical content by electronic means particularly emphasizing projectors such as the CP2000 whose image source is digital data Also known as d cinema and rarely e cinema DIGITAL INTERPOLATION Also known as digital scaling The process of averaging pixel information when scaling resizing an image up or down When reducing the size of an image adjacent pixels are averaged to create fewer pixels When increasing the size of an image additional pixels are created by averaging together adjacent pixels in the original smaller image DOT CLOCK The maximum frequency of the pixel clock E EDID The Enhanced Extended Display Identification Data standard established by VESA enables properties such as resolution of a display device to be detected by the display card in a controlling device such as a PC The PC in turn can then output in a matching format to fill the display Some sources used with the projector are VESA E EDID reported E STOP Emergency stop of the presentation due to equipment failure a commotion in the audience or any trigger from the theatre s life safety system that could require stopping the show raising the house lights and enabling a PA announcement FOOT CANDLE The intensity of visible light per square foot FOOT LAMBERT
242. sed for ASCII messaging since the TPC recognizes Ethernet only and is too slow for servers Cine IPM 2K Connect the Cine IPM 2K s custom RS 232 cable from the rear of the Cine IPM 2K to the serial communica tion panel port labeled RS 232B on the Source and Communication Connection Panel located on the underside of the projection head near the front The RS 232B port uses Christie proprietary protocol and is compatible with Christie accessories only Linking the Cine IPM 2K to the RS 232B port enables Cine IPM 2K sources to be selected at the TPC IMPORTANT Do not use RS 232B port with other devices Refer to Figure 2 28 Tilt Projector to Match Screen on page 2 19 for serial port locations Access from within the pedestal CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Appendix D GPIO System Integration This section explains how to use a GPIO link from the projector to external equipment such as devices for 3D synchronizing CP2000 SB User Manual D 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH ISTIE i The GPIO Port D 1 The 37 pin GPIO connector is located on the Source and Communication Panel located on the underside of the projection head near the front It provides a flexible method of interfacing a wide range of external I O devices to the projector often so that an event on one device automatically triggers an event on the other The pins on this connector that are configurable using t
243. serial cable to the RS 232 A port instead This communication link is acceptable for using a PC laptop to run Christie s DCP Librarian or to download new software but is too slow for server communications and does not support ASCII messaging to the TPC which requires Ethernet Connect RS 232 as shown in Figure 2 27 and route as shown in Figure 2 23 Figure 2 24 Figure 2 25 and Figure 2 26 NOTE For serial communication using a PC laptop or server use only the RS 232 A port The RS 232 B port utilizes Christie proprietary protocol intended for Christie accessories only Warning The RS 232 B port is compatible with Christie accessories only Adjusting Tilt and Leveling NOTE Disconnect from AC for these initial alignments Images are not yet needed In an ideal installation the CP2000 SB lens surface is centered with and parallel to the screen This orientation helps to ensure optimized lens performance with minimal offset Figure 2 28 If this position is not possible such as when the projector is significantly higher than the center of the screen it is better to rely on offset rather than extra tilt J 90 TT ii Tilted Projector Before adjusting tilt ensure the projector is as Inciined sereen WELL CENTERED lt gt with the theatre screen as Figure 2 28 Tilt Projector to Match Screen possible for your installation area refer back to Figure 2 2
244. server and wait several seconds for the projector to receive the set of decryption keys from the server If after 30 seconds the projector doesn t recover pause or stop the show and try playing again If this doesn t work try resetting the server 2 Make sure the IP octets for the projector and the server Eth port match 3 CineCanvas does not have the correct projector IP address Check the IP address of the projector and server and change if necessary They should match 7 4 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 7 6 7 6 1 7 6 2 7 6 3 7 6 4 7 6 5 7 6 6 Non Cinema Displays The following troubleshooting entries assume that you are using a 3rd party input source for displaying alternative non cinema material As a first step always consult the documentation supplied with the external equipment The Projector is ON but There s No Display Was a lens cover accidentally left on Remove lens cover Make sure the douser is OPEN Is the lamp ignited Press the lamp button on the Touch Panel Controller Is the correct DVI display button selected on the Touch Panel Controller Is AC power connected Sy Moo p Dai Is an active source connected properly Check the cable connections and make sure the alternative source is selected 7 Can you access test patterns If so check your source connections again The Display is Jittery or Unstable 1 Ifthe non cin
245. settings in the supplied PCF and 2 the remaining Custom parameters that are not contained in a PCF the physical location of the input connection such as a cinema port or DVI port the screen format data format and processing path CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Custom Page 1 Menu Section 1 Introduction As shown in Figure 3 8 and Figure 3 9 clearing or checking the Use PCF checkbox determines which Custom settings are available for use ID for current custom settings Appears on Main menu Source connection location Icon for current setup Click to change Always select for cinema sources Use full cinema processing amp scaling Use for all cinema sources plus DVI sources with vertical freq 60Hz or lower Main status Custom Advanced Adgin About A fe 1920x804 Scope a Packing mode and 1422 Unpack 10Bit O E Fran w bits of your source Figure 3 8 Custom Page 1 Menu Using Pre defined Configurations a seoa el pomes _Page 1 Page 2 30 Contra J tame Jens Use pre defined PCF Refresh Update Refresh all selection lists available in Custom Menu 3D is in use 3D Control Menu Clear 1 or more channels restore factory defaults Native color reference Choices defined by installer Default OnSite PCF list replaces Color Space Gamma LUT CLUT Target Color and Source options List is configured
246. side the projection head CP2000 SB User Manual 2 29 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHRISTIE 2 9 1 Calibrating the System Using DCP Librarian Setup Software 2 30 NOTE DCP Librarian described here is licensed software intended for Christie installers only Many of its functions are now available at the TPC DCP Librarian is a comprehensive Windows based software application used for calibrating image color performance and defining electronic screen masking required in your particular installation and for creating individual Projector Configuration Files PCFs and specific source files necessary for proper display of incoming material DCP Librarian also defines the system network configuration for communication links to the projector transmitting information to and from the CP2000 via an Ethernet or RS 232 connection Chief functions many of which can be done at the TPC are introduced below Color Calibration After the CP2000 SB is installed and all components are mechanically aligned for optimized light output and geometry at the screen its electronic system processing must be calibrated to ensure accurate color display in the new environment In this one time global calibration the installer measures initial colors at the screen and enters this data called Measured Color Gamut Data into Windows based DCP Librarian software installed on a laptop The software then calculates precise corrections nee
247. sscscesccucsesscesesscecceseesssecsssesesseessnsasessess 7 3 7 2 5 Lam pLOC Does Not S em to Work sc ccssedpucescszsuscnesascveshacieinencdietanpetseoiesnienshemesouuaiiensess 7 3 7 2 6 LiteLOC Does Not Seem to Wr sisiasisescianssasssavsssasvasnadsasoyhaaodaassausssphvnessasesevanpnaaisantoes 7 3 pe Sec i E E E de nd ag E E A E E E A 7 3 gA Ae LEa S AA TN E E E A A A E A A E E ee eee TT 7 4 T3 CAME NG Displays iia cine cose seceoacsusetoaedes EEEE EREE asec 7 4 7 5 1 Blank Screen No Display of Cinema Image 2ci0scsasssscestennnedaonssnnsscavesxesoaniavaveassesseapsredsavianes 7 4 7 5 2 Severe Motion A Tt facts 5 siccassnadeceiansaciiadncesvasdssaviandyaievaadpaeduseppsacciagaaaed ea ETEEN EEEE iE 7 4 7 5 3 Image Appears Squeezed or Vertically Stretched into Center of Screen cc eee 7 4 7 5 4 No Image Just Pink SHOW sas ccssicsissaconncesecassinseecevane conssicassaussansriotancnehewesenrsaconeatsecmeateseereanacdneys 7 4 WO Wom tile Displays ssuinrunonni en A E ER 7 5 7 6 1 The Projector is ON but There s No Display ccccecssecsseceseceeeeeeeeeeseeceaecneeeeeaeesseeesaeenes 7 5 7 6 2 The Display is Jittery or UnStaBle ss scssisssavcaiesenssaseransnetssedsticsse leavers oaoisontiatate Rien ectesesiaase 7 5 7 ocd Th Display 18 F Ali osscestsivcscsavnencesassanddhsnuneeeventedcsWesiorcimaduvsdanesibenedubncpneesbanessedbensdedsasuresatanesss 7 5 7 6 4 The Upper Portion of the Display is Waving Tearing or Jittering ce
248. ssorted cabling most pre connected and misc assembly hardware e CP2000 SB User Manual Protective Clothing Kit for opening of lamp door 598900 095 DCP Librarian Setup Software for calibration setup by Christie installer CP2000 SB User Manual 8 9 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE 8 10 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Appendix A Glossary The glossary defines the specific terms used in this manual as they apply to this projector Also included are other general terms commonly used in the projection industry CP2000 SB User Manual A 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 3 2 PULLDOWN A frame sequence used to map 24 fps film to 30 fps video or 24 1 001 to 30 1 001 fps in which every second film frame is represented by three video fields instead of two the third being a repeat of the second This leads to a set of ten video fields for each four film frames ACTIVE LINE TIME The time inside one horizontal scan line during which video is generated ACTIVE PICTURE The area of a video frame which carries image information As an example a total frame size of 1125 x 2200 pixels may have an active picture of 1280 active lines and 1920 samples per active line Compare to production aperture ALTERNATIVE CONTENT Non cinema program material such as concerts plays sporting events and potentially corporate training o
249. sumes the 3D stereo sync signal is included with the image data inputs rather than supplied separately at the GPIO port WHITE LINE or BLUE LINE Select only if using a single 3D input signal in which an embedded white or blue line at the bottom of each frame identifies left vs right and an additional separate 3D stereo sync input at the GPIO port is not present Short line Left long line Right NOTE Requires single 3D input Not currently supported e ASSIGNED GPI Select only if using a single 3D signal requiring a separate 3D stereo sync input at the GPIO NOTE Requires single 3D input Not currently supported L R DISPLAY REFERENCE NOTES Select the option matching your L R Input Reference above e If your 3D source provides separate left and right data via 2 cables at the A and B SMPTE ports simply select the desired frame order either L R or R L If your single 3D source provides a separate sync connected at the GPIO or if the single 3D source includes an embedded 3D sync signal code the Input Frame Dominance choice should match that of the L R Input Reference default or if necessary be inverted NOTE Requires single input not currently supported L R OUTPUT POLARITY NOTES e TRUE 3D L R sync output from GPO will match L R sync input e INVERTED 3D L R sync output from GPO will be the opposite of sync input left becomes right and right become left FRAME RATE N M NOTES EXAMPLE 4 2 4 frames displayed
250. t A is connected to projection input A and the cable connecting server output B is connected to projection input B Set Output GPO according to which of the projector s GPIO outputs is currently wired to your emitter or polarizer 7 CONNECT GPIO OUTPUT From the projector s GPIO port connect your 3D stereo sync cable to your 3D controlling device such as an emitter or polarizer NOTE RealD 3D sync cable recommended 8 ADJUST DISPLAY SCREEN ETC As desired adjust the display screen image color etc 3 10 6 3D Troubleshooting Using the 3D Test Pattern Use the 3D internal test pattern to confirm 3D mode L R renia eh Mapentatald Hs orientation and your Sync Output GPO setting only This pattern automatically activates 3D mode and increases frame rate by a factor of 6 2 NOTE The test pattern will flicker significantly due to its low frame rate and is not recommended White Black for synchronizing projector processing with your 3D device Image Breakup Increasing the Dark Time beyond its maximum may cause image break up White Black No 3D Effect Figure 3 59 Internal Test Pattern for 3D Certain settings in the Custom 3D Control menu are likely reversed Ghosting Cross Talk Ghosting or cross talk indicates that the eyes are detecting portions of the opposing frame due to an out of sync system Adjust Dark Time and or Output Delay so that the projector s display output is synchronized wi
251. t information such as what channel is currently in use the projector then returns the data in a reply message Regardless of message type or origin all messages use the same basic format and code as shown in Figure 3 40 Where applicable a message can expand to include additional parameters of related data Message Format Function Examples CHA 103 or CHA103 SET set channel to 103 From Controller REQUEST whats current channel CHA REPLY channel is 106 CHA 1 06 Figure 3 40 The 3 Message Formats shaded message is from proj Message Components and Structure START AND END OF MESSAGE Every message begins with the character and ends with the character Note that if the start character is received before an end character of the previous message the partial previous message is discarded FUNCTION CODE The function you wish to work with such as channel switching or picture mute is represented by a three character ASCII code A Z upper or lower case This function code appears immediately after the leading that starts the message REQUEST REPLY SYMBOL If the controller is requesting information from the projector a question mark appears directly after the function code If the projector is replying an exclamation mark appears directly after the function code For set messages neither of these characters appear the code is followed by the data itself see next paragraph
252. t more than aiming to center the image in off axis installations 3 For best results avoid extreme tilts or offsets Corner vignettes on a white test pattern indicates extreme offset that should be avoided using mechanical alignment CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction The maximum vertical offset is shown in Figure 2 38 bottom illustration NOTES 1 Horizontal offset is just a few dozen pixels resulting in a maximum of 52 of the image displayed on one side or the other of the lens 2 Maximum offsets are slightly less when offsetting in both directions H and V at once Ai p 50 lens center SS 65 SS Maximum amount of display below center of lens 65 approx Figure 2 38 Vertical Offset Range 2 8 2 Adjust Left Right Boresight The goal for left right boresight alignment is to adjust the lens mount until both sides of the image focus on the screen simultaneously Projectors are aligned properly at the factory but due to mechanical tolerances in the alignment between the projector and the screen the left and right sides of the image come into focus at different times By focusing on the left side of the screen we need to determine if the right side of the image focuses in front or behind the screen relative to the left side NOTE Use a test pattern with a single pixel vertical and horizontal line and perimeter frame such
253. tatus submenus Server Diag and Interrogator The installer can define system operating parameters such as which projector is controlled by the TPC and critical lamp parameters such as installed lamp type fan speed and light level at the screen Installers can also establish temperature scale preference remote access rights test pattern access rights extent of data logging An installer can see ID and error information for servers as well as a detailed diagnostics log for in depth troubleshooting TPC Power up Defaults When the CP2000 SB powers up refer to Section 3 2 Power up Procedure the Touch Panel Controller will begin the steps of Initializing Attempting to log on andUpdating status displaying its progress on the TPC status bar at the bottom of the screen When initializing is complete all files are refreshed on the TPC and the system is in a ready to use default operating mode The Main menu appears on the Touch Panel Controller where you can press the lamp button to turn on the lamp The most recently used display button is depressed darkened Upon turning on the lamp the image will appear Failed TPC Connection If the TPC fails to initialize and instead displays a communication error such asNo connection or Cannot locate Ethernet port orWaiting to Connect there is likely a bad connection or address between the TPC and the rest of the projector Check that TPC cabling is intact and try again Review Section
254. terrogator is also accessible through a separate login and password different from the service login Contact Christie tech support for assistance and password NOTE Password protected Figure 3 62 Status Interrogator Menu Options 3 72 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE 4 Cinema Operation This section explains how trained operators can use the projector for presenting cinema events such as first run movies stored on a digital media storage device Please read through these pages before displaying cinema for the first time A good understanding of all cinema functions and how to access them will help you to run an event smoothly and easily NOTE Before attempting cinema use the projector must be properly installed aligned and configured by a qualified service technician as described in Section 2 Installation amp Setup Read also Section 3 Operation 4 1 Compatible Cinema Sources 4 2 Image Formats 4 3 Selecting the Cinema Source 4 4 Adjusting the Cinema Display CP2000 SB User Manual 4 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction 4 1 4 2 CHISTIE Compatible Cinema Sources Ensure a digital media storage device or cinema server is connected to one of the A or B input ports within the CP2000 SB head see Figure 4 1 These connections are typically made at the time of projector installation This panel is located on the underside of the projection hea
255. th the gating switching of your glasses Motion Artifacts If the image seems to jump back and forth during horizontal pans the L R Display Sequence is likely backwards Try reversing the current setting Single 3D Input Does Not Work A single source signal containing both left and right data is not currently supported 3 70 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHAKISTIE Section 1 Introduction 3 11 Working with Servers and Diagnostics NOTE Password protected Installers and service technicians only A service login provides three additional Status menus Server Diag and Interrogator for testing certain server functions and communications or for advanced projector diagnostics 3 11 1 TPC Status Server Menu The Status Server menu provides controls for testing or confirming subtitling and or metadata commands supplied with presentation content from the site s controlling cinema server The relevant xml files one for subtitling one for metadata can be searched and examined for errors in content or in transmission from the server Reported errors can then help point to potential problems with the server the xml file or the communication link to the projector Note that controls in the Server menu do not activate or turn off metadata or subtitling Controls are diagnostic tools only TEST SUBTITLING FILE xml Enable the Subtitling button to test an xml file supplied with content for control of performan
256. the lamp has never been used the value should be 0 Advanced Lamp History Menu A list of the last 10 recorded lamp serial numbers appears here along with their dates of entry and number of hours logged This is a read only menu unless activated via the New Lamp button on the Advanced Lamp menu which adds edit boxes and a Save button for recording in memory the serial number of a new lamp and the number of hours it has already been in use if applicable Main Status Custom Advanced admin about Date Time Type Serial Number Hours C 2006 03 20 10 37 JB0908 6kW 274 Fi 3 30 Preference Lamp Lamp History Lens Test Pattern User gure 3 19 Advanced Lamp History Menu Options CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE Section 1 Introduction Advanced Lens Menu As shown in Figure 3 20 use the fields provided in the Lens menu to select a lens type and record its serial number Select lens type from drop down list Intelligent Lens System Calibrate ILS asas Eel fizssss OOOO E aerer number for the newly installed one O iniisa OO a a Lens Reset Lamp History Lens Test Pattern J user Figure 3 20 Advanced Lens Menu Options Table 3 12 Advanced Lens Options ADVANCED LENS OPTIONS Primary Lens From the drop down menu select the type of primary lens installed on the projector Auxiliary Lens If an auxili
257. the response rate of the lens upon selecting the buttons Figure 3 54 Intelligent Lens System Zoom From the Main Lens menu click the zoom in out buttons to enlarge or shrink the image in each direction as necessary CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 3 9 2 Offsets From the Main Lens menu click the up down left right buttons as necessary to adjust the image and make it square on the screen For best results avoid extreme tilts or offsets Corner vignettes on a white test pattern indicates extreme offset that should be avoided If you need more vertical offset range it is possible that the projector s mechanical TILT should be changed to help compensate for significant differences in screen and lens height Focus From the Main Lens menu click the focus buttons as necessary for overall focus improvements For best results use a crosshatch test pattern or similar and focus on the center of the image Figure 3 55 Focus Center of Image If the focus quality differs from edge to edge whether top bottom left or right the boresight of the lens mount likely needs correction Refer to Section 2 8 Offset and Boresight Alignment Auxiliary Lens NOTES 1 The auxiliary lens and its motorized mounting mechanism are optional 2 To install replace or use the auxiliary lens refer to the instructions included with the Motorized Auxiliary Lens Mount kit
258. tion System Error and System Warning error messages also include further explanation of the nature of the error such as its location and cause NOTE The type of error and text parameters are enclosed together in quotation marks separated by a colon and space In the table below the text explanation appears as Table B 2 Error Messages Error Code P1 Type of Error P2 Meaning 001 System Error System critical error 002 System Warning System error 003 Invalid parameter Invalid parameter number 004 Too many parameters Message requires fewer parameters 005 Too few parameters Message requires more parameters 006 Source does not exist The source is wrong 007 Could not be executed Current content prevented the command from executing 008 Checksum error The checksum is incorrect 009 Unknown request Message code undefined If the message sent as a command it is ignored and no error is returned 010 Communication error Error receiving serial data on one of the RS 232 ports Additional Parameters for 001 System Errors and 002 System Warnings System Error and System Warning error messages include two additional parameters P3 and P4 which further describe the error P3 indicates what component or system is involved such as interlocks fans temperature SSM communication or a lamp failure and P4 relays the specific condition detected at the s
259. to recover usually 2 39 or 1 85 Because the incoming signal may be pre squeezed the aspect ratio entered here will not necessarily match that of the incoming aspect ratio See Aspect Ration Notes below Slidebars Adjust resolution and or offset as desired Create Source Save current resolution offset and aspect ration settings as a Source file that will be accessible and applied from within the Custom menu Restore Cancel new unsaved source settings of resolution offset aspect ratio Test Apply current settings to the image without saving RESOLUTION NOTES To capture process all of the incoming data enter the full resolution of the incoming source material or leave at 0 default Regardless of whether or not the original material has been squeezed for use with an auxiliary lens enter the current incoming resolution This may not necessarily match the resolution of the projector or the original filmed material depending on how the source was formatted before distribution For example an original 2048 x 1080 native source supplied pre squeezed as 1920 x 1080 requires a source file indicating this incoming 1920 x 1080 resolution To capture only a portion of an incoming image full screen like a zoom function enter the approximate horizontal width and vertical height defining the area of the image you wish to zoom in on The projector will automatically scale a center area of this size so that it fills the pro
260. to source and from site to site If the environment degrades or changes such as if an auxiliary lens is swapped on and off or if an internal optical module is replaced create one or more new MCGDs naming them as desired To use an MCGD file as the reference file for target color processing such as with a certain source and or lens select it in the Custom menu 3 40 CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction Desired x y target coordinates for each color ee Main Status Custom Advanced Admin About caoidinates for SLO Target TCGD each uncorrected color Luminance Turn test pattern off Enable disable tolerance NOTE A Save MCGD tolerance discards coordinates to new onSite file or Define 4 corners other file WEES PTEN accessed in the p Create MCGD we arte a Custom menu around white Save TCGD Create TCGD coordinates to a Source Screen Ga 1 new target file Eas less light Go back to previous MCGD and TCGD coordinates NOTE Restore of MCGD Test target color in requires that display without coordinates be saving Figure 3 30 Admin Gamut Menu Options tested via Test but ton but not saved accessed in the Custom menu Table 3 17 Admin Gamut Menu Options ADMIN GAMUT MENU OPTIONS Measured MCGD Activate each color which projects a special full field test pattern and enter the x y
261. troller TPC Power up Procedure NOTE This is a manual power up procedure Some cinema installations may include an automation system that controls lamp ignition in conjunction with other theatre variables such as house lights audio and the start of the feature from a digital media storage device server NAGI Do not attempt opera tion if the AC supply and pedestal are not within the specified voltage range A KC Y a i 1 Ensure that the breakers at the main wall panel for the CP are switched ON A Ef REAKERS ON f 2 At the operator s side of the pedestal set all CP2000 SB circuit breakers to ON these are main AC 3 phase the projection head 2 HL A P b The MAIN AC light will be green if AC is main status Custom Advanced Adin About as W phase and terminal block single phase Z present components such as fans and power Ba eee am ae supplies will start up and the TPC will begin Ay 1998x1080 Tine Ba Flat P3 im Scope P3 initializing Reserved A Reserved 3 When the TPC has initialized approx 15 30 a ERE CM pcre Isl seconds indicated by a green circle in the Ba 1920x1038 a peman iE left corner press the lamp button on the E TPC Main menu to ignite the lamp S700 IF THE LAMP DOES NOT IGNITE Figure 3 2 Power up Procedure e Ifa safety interlock switch is open such as when the lamp door is ajar the lamp ca
262. ual 1 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction 1 1 CHISTIE The Projector The CP2000 SB is a professional quality easy to use DMD projector utilizing Digital Light Processing DLP Cinema technology from Texas Instruments which integrates smoothly into traditional projection environments such as theatres and other wide screen exhibitor venues These projectors provide stunning wide screen high resolution cinema images that remain flawless from first release to final show truly the solution for critical digital cinema applications CP2000 SB interfaces with local networks typical in theatres throughout the world and can be expanded even further by connecting non cinema DVI source material for multimedia presentations from a variety of formats The Christie HDCP Interface Board enables CP2000 SB projectors to accept and display HDCP protected content The CP2000 SB accepts an HDCP signal from a wide variety of sources such as Blu Ray players HD receivers and HD DVD players if such sources are fed directory into the projector 1 1 1 New Features e Motorized Lens Mount automates the process of setting the Focus Horizontal X and Vertical Y Offset and Zoom NOTE 7PC version 2 9 higher is required 1 1 2 List of All Features 1 2 DLP Cinema 3 chip electronics with 2048 x 1080 native resolution Versatile electronic and optical scaling to fill wide screens CineBlack and Ci
263. uction to the Touch Panel Controller Most users will use the Touch Panel Controller TPC as their main interface with the projector Depending on the installation this Windows based touch sensitive screen is typically mounted on the rear of the projector or at some other convenient nearby location Installers must pre program it appropriately for use at the specific site User Access and Rights Whether or not you can access specific TPC menus and functions depends on how you have logged on to the TPC See Figure 3 4 General Users For the general user having no username or password the Touch Panel Controller TPC offers three menus providing e ON OFF toggling of the lamp shutter auxiliary lens position user test patterns and pre configured displays e Basic status and or diagnostic information about projector components e Versions of software components currently installed Service Installer Admin Advanced General Any User Ey Status i i f i 1 i 4 Operator Can use New Lamp button Figure 3 4 TPC User Access Rights A simple design with familiar menu icons enables a novice user to display an accurate and fully optimized image by pressing a single button on the touch screen and precisely configured presentations are protected from accidental or unauthorized change CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 3 4 2 3 4 3 Train
264. uire the following for installation Full understanding of all site requirements and characteristics 12 screwdrivers Phillips magnetic and flat Assorted wrenches such as 7 8 and 3 4 Assorted Allen keys such as 3 16 7 64 5 32 and M3 3 phase 4 wire 5 wire or 6 wire connection of AC supply to Terminal Block 1 in pedestal certified elec trician required Heat extractor such as inline centrifugal blower Elicent model AXC 315B or roof extractor providing at least 450 CFM 2 or 3 kW lamps or 600 CFM 4 5 or 6 kW lamps at 8 exhaust duct opening 600 watts or lower NOTE Mount at an external location Lamp and protective clothing safety gear Laptop computer with DCP Librarian setup software with Ethernet or standard RS 232 cable Vapor free dustoff type compressed air can Latex lab gloves Lens cleaning tissue and solution refer to Section 6 3 Maintenance and Cleaning Servicing Energized Live Christie Equipment To make sure you remain safe when servicing energized live Christie equipment Locate the main AC power shut off prior to servicing the equipment This will allow you to turn the power off quickly in an emergency Disconnect the projector from the communication and management network so it cannot receive commands to turn the lamp on open the douser and move the lens Familiarize yourself with all potential safety hazards prior to servicing the equipment This includes but is not lim
265. ult Choices are pre defined using DCP Librarian or the TPC Admin menu Target Color Identifies sets the special color processing called Target Color Gamut Data established for a given presentation Default P7V2 Theatre Color Space Identifies sets the method of color decoding for the current source Default RGB for all DVI sourceso Default YCbCr for all cinema sources i e SMPTE A or B ports Gamma Identifies sets the desired gamma a k a de gamma correction needed for proper tonal range of the source material for example a grayscale test pattern will be neutral and smoothly graduated In the atres the only gamma setting currently needed is PL2 6 These components are part of any pre defined PCF Projector Configuration File that controls image processing for a given source When the Use PCF checkbox is checked these components disappear from the Custom menu and are protected from further change Custom Page 2 Menu Use the auxiliary lens with this channel Main State s Custom Advanced Admin About Current channel e M Auxiliary Lens In M Pull Down Re Sync defned by beter or sdnbicve pee ee tor Scope v 2 2 Pull Down v Define frame sequence Native color reference Choices Measured Color Pull Down Offset defined by installer Default OnSite Complex Look up Table Type s gt LUT CLUT SMPTE Field Bit Applies a 3 dimensio
266. uspect component such an over temperature reading or a slow fan speed reading note these values indicate temperature or fan speed only See Table B 3 Table B 4 and Table B 5 When a system error is resolved and is no longer present another message reports this by replacing the first digit in the original P3 error code witha 1 CP2000 SB User Manual B 15 020 100162 06 Rev 1 03 2014 Section 1 Introduction B 16 Table B 3 P3 Codes for 001 System Error Messages Component Code P3 Component 1 Interlock Lamp Fan 2 Interlock Extractor exit duct to outside world 3 Interlock Lamp Door Open 4 Interlock Auxiliary 5 Interlock Card Cage Tamper Interlock 8 Fan Intake 1 non operator s side of projection head 9 Fan Intake 2 non operator s side of projection head 10 Fan Card Cage 11 Fan LAD laminar airflow device near light engine 12 Fan Ballast 16 Prism Over temperature 17 DMD Red Over temperature 18 DMD Blue Over temperature 19 Integrator Over temperature 20 SSM System Supervisor Module Over temperature 21 Card Cage Over temperature 22 Ballast Over temperature 32 Lamp Life Expired 33 Lamp Failed to Strike 35 Unexpected Lamp Failure Off 36 Reading Lamp Intensity Failed 48 SSM Communication Failure System Supervisor Module 48 SSM Upgrade Failed 68 17C Communication Failure CHRISTIE CP2000 SB User Manual 020 100162 06 Rev 1
267. utdown of the socket program the controller to send a PNG every 5 10 min utes SHUTDOWN Warning You must close the application and shut down the socket properly before shutting down the control ler CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHY IS TIE Section 1 Introduction 3 7 3 7 1 3 7 2 Upgrading SSM Firmware These instructions explain how to upgrade SSM firmware without upgrading the rest of the software The correct SSM firmware must be downloaded to the SSM in order for the DMD temperature warning and shutdown limits to be properly set You will use an FTP program to transfer the new version file from your PC to the TPC currently connected to your CP2000 SB projector Requirements e TPC 642 or TPC 60 or TPC 66 used with any CP2000 SB projector e Windows 2000 or XP running on a laptop or PC e Correct SSM Firmware version e Version 2 0 for CP2000 SB 106 004101 01 only e Version 2 1 for CP2000 SB 106 004101 02 or higher e FTP application such as FFFTP or WS_FTP or as provided in Windows XP or Internet Explorer Update Procedure NOTE Screen shots throughout this section are for representation purposes only and may differ slightly from those on your screen FFFTP is a freeware FTP client application recommended for communicating with the TPC via file transfer protocol NOTE FFFTP is the only supported FTP software When installed and configured on a PC the PC and TPC can transfer fi
268. vanced Admin About Diag 1998x1080 EA 8 A 1998x1080 A 2048x858 g Flat P3 Scope P3 1 Select pre defined source large button AN Reserved nii Reserved X 2 Image will change PCF Flat i PCF Scope PA 1920x1038 WA 1920x804 Flat P3 Scope P3 CH 9 16 CH 17 24 CH 25 32 Lens To additional sources Figure 4 6 Select the Desired Source NOTES 1 Depending on your expected needs your installer may or may not have configured all buttons for use 2 Buttons may have any icon or text CP2000 SB User Manual 4 7 020 100162 06 Rev 1 03 2014 Section 1 Introduction CH ISTIE i 4 3 2 Other Methods 4 4 4 8 Depending on your installation you may be able to use ASCII commands via Ethernet communication link to select a source from a different controller in a remote location Refer to Section 3 6 Remote Control of the Touch Panel Controller and Appendix B ASCII Messages Regardless of how the display file is selected the feature will appear on screen according to the numerous specific display settings defined for it If the display does not appear as expected on screen part of the display setup is probably not configured correctly for the incoming source Try a different button on the Main menu If the image is still incorrect this source may have to be re configured Adjusting the Cinema Display For general users only the selection of a digital cinema feature is accessible The precise processing
269. ve current settings to a new TCGD NOTE Industry standard TCGD files are write protected and cannot be modified unless saved under a different filename For theatre use there should be little need to create custom TCGDs as the pre defined TCGDs are used instead See Create TCGD Notes below CP2000 SB User Manual 3 41 020 100162 06 Rev 1 03 2014 Section 1 Introduction CHY IS TIE i 3 42 MEASURED MCGD NOTES For each color record the native uncorrected x y color coordinates measured at the screen These values simply represent the currently viewable primary colors and collectively when saved will define the raw color performance reference point for this projector in the current environment Each radio button activates the corresponding full field YCbCr test pattern of this native color so that measurements can be taken For example to measure the red coordinates click the Red radio button to change the screen display to full field red and measure coordinates at the screen Repeat for each color and record them in the nearby x y text boxes After all colors have been measured and recorded select Pattern Off to leave the special test pattern mode To cancel changes and return to the previous MCGD coordinates leave the menu without saving CREATE MCGD NOTES This button collects the current color values entered for Measured MCGD where you can save them as a new OnSite MCGD file or as a different MCGD file with a dif
270. ving freely The pre installed outside venting duct should be rigid for a 10 length at the projector and must also include a heat extractor blower that maintains at least 450 to 600 CFM when measured at the projector exhaust opening depending on the lamp See Table 2 1 Table 2 1 Airflow Requirements Minimum Exhaust Airflow Rate Lamp kW u Figure 2 17 Attach Exhaust Ducting 600 ft min CALCULATE CFM in 8 DUCT Use an air flow meter to measure the ft min or ft sec at the rigid end of the duct that will connect to the projector measure right at the end Then multiply the reading by the cross sectional area of the 8 duct to calculate the cubic feet min airflow The formula is Measured linear ft min x 0 34 CFM Depending on the lamp calculations should show 450 or 600 CFM airflow see Table 2 1 in the 8 exhaust duct Add extractors boosters as needed for your site as the vane switch see right will prevent the projector from operating if the airflow is inadequate Do not mount extractor on the projector NOTE f the duct becomes significantly blocked or if a fan fails the projector should trigger an alarm before becoming overheated or unsafe Regardless check airflow regularly as described in Section 6 2 Maintaining Proper Cooling Warning Never disable a vane switch Attempting to operate the projector with inadequate airflow can result in dangerous overheating of the projector ty oS Fi
271. which affects details of image quality is predefined in its display files such as Source and Screen these settings are password protected and accessible by trained operators or installers only If you feel the cinema display is incorrect or faulty contact the trained operator in your theatre who can correct or further customize specific display file settings CP2000 SB User Manual 020 100162 06 Rev 1 03 2014 CHRISTIE 5 Non Cinema Operation This section explains how to display alternative content originating from a standard definition or high definition non cinema source such as a PC or other graphics devices Such a source routes to a DVI Digital Visual Interface port in the CP2000 SB projection head and can bypass cinema processing when necessary e 5 1 Compatible Non Cinema Sources e 5 2 Selecting the Source CP2000 SB User Manual 5 1 020 100162 06 Rev 1 03 2014 Section 1 Introduction 5 1 5 2 Compatible Non Cinema Sources CHRISTIE Ensure your non cinema DVI source is connected to DVI 1 or DVI 2 within the CP2000 SB head see Figure 5 1 These connections are typically made at the time of projector installation PANEL A B DVi2 GPIO DVI 1 6 3 o 000000000000000 4 oF goo00o0oco0000000 eae LI RS 232 B Q e3 oo000 C E ETHERNET A or DVi Sneen i

Christie CP2000-SB User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents