Harbor Freight Tools 6 in. Dial Caliper Product manual
Contents
1. to use Figure 8 To read the Scale and Dial the 9 Read the Scale Measurement Point in Sliding Index Edge features readings inches and tenths of inches such as 0 5 in inches 0 001 and 0 010 per Then read the Dial Needle on the Dial in call out segment See Figure B thousandth of an inch such as 081 10 Combine the two readings for a final reading of 0 581 Sliding Index Edge Dial Figure B Item 62362 For technical questions please call 1 888 866 5797 Page 3 11 To use the Caliper to measure the outside diameter of an object close the Outside Diameter Jaws over the object making sure that the item rests squarely on the Jaws See Figure C below 0 Figure 6 12 To use the Caliper to measure the inside diameter of an object see Figure D below i Figure D Page 4 For technical questions please call 1 888 866 5797 Item 62362 13 To make a depth measurement of an object see Figure E To measure the step of an object see Figure F Figure E Figure F PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR D2. ISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Item 62362 For technical questions please call 1 888 866 5797 Page 5 Parts List and Diagram Description Thumb Roll Outside Diameter Jaws Dial Adjustment Lock Dial Adjustment Dial Slide Scale Lock Sliding Index Edge Inside Diameter Jaws Step Measuring Surface Depth Measuring Blade 9 eA U 00 co 29 a a a po n 0 3 9 s os Y TOTS Page 6 For technical questions please call 1 888 866 5797 Item 62362 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts Item 62362 For technical questions please call 1 888 866 5797 Page 7 PITTSBURGH 3491 Mission Oaks Blvd gt PO Box 6009 Camarillo CA 93011 1 888 866 5797
3. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference P T TTSB URG 1 62362 6 Dial Caliper Visit our website at http www harborfreight com REV 14d Email our technical support at productsupport harborfreight com When unpacking make sure that the product is intact AWARNING and undamaged If any parts are missing or broken please call 1 888 866 5797 as soon as possible Copyright 2014 by Harbor Freight Tools All rights reserved 1 2 No portion of his manual or any artwork contained herein may be reproduced Read this material before using this product Failure to do so can result any shape or form without the express written consent of Harbor Freight Tools Diagrams within this manual may not be drawn proportionally Due to continuing serious injury SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Scale Units 20 007 Measuring Capabilities Inside Outside Depth Step Scale Type Mechanical Dial Important S
4. afety Information 1 This product is not a toy Do not allow children to play with or near this item 2 Wear ANSI approved safety goggles during use e Keep work area clean and well lit 5 Do not operate when tired or when under the influence of alcohol drugs or medication 5 6 Use as intended only Inspect before every use do not use if parts are loose or damaged Maintain product labels and nameplates These carry important safety information 1 unreadable or missing contact Harbor Freight Tools for a replacement Page 2 For technical questions please call 1 888 866 5797 Item 62362 Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product 1 Make sure upper and lower 5 To adjust if needed loosen Outside Diameter Jaw 2 faces the Dial Adjustment Lock 3 by are clean See Figure A turning it counterclockwise 2 Loosen Slide Scale Lock 6 by turning it 6 Set the Dial 5 by turning the Dial counterclockwise Adjustment 4 either clockwise 3 Use Thumb Roll 1 to close or counterclockwise until the Dial Needle points to 0 Outside Diameter Jaws 2 di n 7 Lock the Dial 5 on its 0 setting by 4 Sliding Index Edge 7 should 2 6 should ling tightening the Dial Adjustment Lock 3 clockwise The Caliper is ready
Download Pdf Manuals
Related Search