User Manual MO2000 - DCA
Contents
1. could be very hot Paper feeding direction Fb Intertel 21 Intertel 8 4 Sensors A reflective sensor is used on MP 2000 for determining the PAPER END condition When this sensor detects the end of the currently printed sheet the following actions take place 1 printing stops 2 the printer switches to OFF LINE ON LINE indicators goes off 3 PE PAPER END indicators comes on 4 carriage moves to middle of the printer span In order to resume printing a new sheet should be loa ded and the ON LINE pushbutton should be pressed The PAPER END sensor is also used to detect an open mechanism condition When the mechanism is open the sensor no longer sees the sheet and actions described above take place The carriage is likewise moved to the center until a new sheet is introduced the printer mecha nism is closed and the ON LINE push button is pressed re Sensor Intertel 22 Intertel 8 5 Maintenance The MP 2000 does not require special maintenance ex cept for the following periodic cleaning approximately every 10 million charac ters of the printhead bearing rod with isopropylic alcohol or similar verification of the distance between printhead and prin ting plate if the printer has suffered major shock or whe never an appreciable occurrence of bad quality printing is experienced The distance measured by a thickness gauge with the printer closed and no inked ribb2. feed push button pressed while the printer is powered up The test procedure prints a first page with general information about the MP 2000 and a second page of fonts CAUTION DO NOT SELF TEST WITHOUT INKRIBBON OR PAPER Intertel 17 Intertel 7 6 Indicators POWER ON This indicator lights when the printer is correctly powe red If the supply voltage drops below 11 5 Vdc the PO WER indicator flashes ON LINE Turns on when the printer is ready to accept data If the ON LINE indicator flashes the printer has switched to STAND BY mode PAPER END Comes on when the printer is out of paper 7 7 Alarm and Indicator Functions The following description assumes that the control panel with associated indicators and alarm is connected to the printer ERROR indicator flashes This means that the motor is locked due to some mecha nical reason it is recommended to turn the printer off to avoid battery pack overcharging Intertel 18 Intertel 8 Printer Operation The MP 2000 control panel is fitted with four control keys three indicators of which one is an alarm indicator 8 1 Control Keys This key switches the printer on and off When ON LINE the printer is ready to accept data from the computer Like wise when it is switched OFF LINE the carriage automati cally moves to the center of the printer span When ON LINE the printer ignores the remaining push buttons If the printer is switched ON LINE when the LI
3. not be responsible for any damages arising out of or in connection with the use of this product Intertel 5 Intertel 2 Contents of MO 2000 The MO 2000 will be delivered with the next items Rugged Executive Case with integrated A4 size impact printer MP2000 GSM modem option Battery Management System Papertray LapTop portreplicator delivered by client LapTop and adapter delivered by client Carrying Belt Serial Cable Portfolio Auto Airline power adapter IBM User Manual Two year warranty Intertel 6 Intertel 3 Identifying the MO 2000 Portofolie Power input Lap Top 1 Unlock button oz Portreplicator Control Panel Lap Top DCA Intertel 7 DCA Intertel The paper tray can be accessed by lifting up the plate on which the Lap Top is mounted On this plate the GSM Modem optional can be found By pushing the unlock button the Lap Top can be taken out of the suitcase Additional equipment can be attached to the Lap Top by plugging it into the portreplicator The paper can be inserted by lifting the cover of the prin ter and then lifting the printer mechanism Notice that the suitcase have to be recharged with the IBM adapter from the Lap Top and or with the Auto Airli ne adapter delivered with the suitcase When the battery is completely recharged you can print at least 80 pages with it The paper can be inserted by lifting the cover of the prin ter and then lifting the printer me
4. 7 4 Caution Do Not print without inked ribbon or paper since this leads to rapid printhead needle wear out Do Not move the printhead manually Avoid mechanical shocks Before starting to print check that the inked ribbon cartridge is correctly installed the paper is loaded in the proper position and the printer s upper swiveling part is locked to the lower one Tf the printer has worked for some time avoid touching the printhead it can be very hot It is advisable to wait a few minutes before attempting to replace the inked rib bon cartridge Once the printer has been turned off wait at least 10 seconds before turning it on again this allows the inter nal reset circuitry to work properly Do Not open the printer when it is operating NOTICE Turn the computer on before the printer and turn the printer off before the computer This is only to avoid dummy data to be sent by the computer printer during the on off sequence Intertel 16 Intertel NOTE The small size of the printhead did not allow for a head paper spacing adjustment device to be used in single copy or multi copy printing Therefore when multi copy printing is performed with a freshly installed inked ribbon cartridge the first printed pages may have some ribbon marks 7 5 Self Test The printer is able to perform an internal self check routi ne followed by a self test printout To execute this procedure simply keep the LINE
5. 8 X 120 x 25 EM 57 9 89 Y 121 y 26 SUB 58 9 Z 12 z 27 ESC 59 91 123 4 28 FS 60 lt 92 124 29 GS 61 93 1 125 30 RS 62 gt 94 A 126 xo 31 US 6 9 127 DEL Intertel 27 Intertel DEC ASC DEC ASC DEC ASC DEC ASC 128 160 192 A 224 a 129 O 161 i 193 A 225 a 130 162 194 A 226 a 131 163 195 A 227 132 164 x 196 228 133 165 Y 197 A 229 a 134 166 1 198 230 135 167 199 231 136 168 200 E 232 amp 137 169 201 E 233 6 138 170 a 202 E 234 139 lt 171 203 E 235 6 140 172 a 204 1 236 141 O 173 205 I 237 142 Z 174 206 I 238 i 143 O 175 207 I 239 1 144 H 176 9 208 240 145 177 209 N 241 146 178 2 210 O 242 6 147 179 3 211 243 6 148 180 212 244 6 149 181 u 213 245 6 150 182 214 246 6 151 183 215 x 247 152 184 216 248 g 153 185 1 217 U 249 154 186 218 U 250 155 gt 187 gt 219 U 251 a 156 ce 188 220 252 157 O 189 221 Y 253 y 158 Y 190 222 b 254 b 159 Y 191 223 8 255 Intertel 28 Intertel Intertel 29 Intertel
6. NE FEED push button is activated a demonstration test is perfor med ONLINE Paper End Error This key advances the paper by one sheet length i e to the beginning of next page This key advances the paper by one line This key retracts the paper by one line m m Intertel 19 Intertel 8 2 Power Source The MP 2000 requires a power source between 11 0 14 0 If the voltage drops below 11 5 VDC the POWER ON indicators flashes If the voltage drops below 10 5 batteries drained the printer stops CONTROLPANEL DCA Intertel O ONLINE ge Intertel 20 Intertel 8 3 Paper Loading MP 2000 can print on UNI A4 A5 size single sheet paper forms or multi part paper forms or continuous fan fold paper with hole to hole spacing of 227mm 8 94 The procedure for correct paper loading is the following Set the printer OFF LINE Open the printer by lifting lever A Fig 2 Insert single sheet module by placing it over the printing plate while checking if it is equally spaced with respect to the printing area in case of continuous fan fold paper be sure that the sprockets engage correctly in the holes provided for near the edges Close the swiveling printer top Switch the printer ON LINE again CAUTION If the printer has been printing for some time it is ad visable not to touch the printhead during paper loading or inkribbon cartridge replacement as it
7. User Manual Mobile Office LapTop with build in Printer DCA s for the mobile workpla www dca group com Table of Contans 1 Customer Care And Service 4 1 1 Warranty And Repair Service 4 1 2 Application Support 4 1 3 Notice 4 1 4 Warning 5 1 5 Limited Warranty 5 2 Contents of MO 2000 6 3 Identifying the MDS2000 7 4 How to 9 5 Description 10 5 1 Printer Overview 10 5 2 Printer Layout 11 6 Technical Specifications 12 7 Installation 13 7 1 Unpacking 13 7 2 Procedure for Installation 13 7 2 1Mechanical installation 13 7 2 2 Driver installation 13 7 3 Printer Setup 14 7 4 Caution 16 7 5 Self Test 17 7 6 Indicators 18 7 7 Alarm and Indicator Functions 18 Intertel 2 Intertel 8 Printer Operation 19 8 1 Control Keys 19 8 2 Power Source 20 8 3 Paper Loading 21 8 4 Sensors 22 8 5 Maintenance 23 8 7 Replacement 24 9 Interfaces 25 9 1 Appendix A 25 9 2 Appendix B 26 9 3 Appendix C 27 Intertel 3 Intertel 1 Customer Care And Service 1 1 Warranty And Repair Service To obtain warranty or repair service please contact DCA Intertel at Phone 31 0 172 604963 or Fax 31 0 172 605237 for a RMA number and shipping instructions 1 2 Application Support If you have any questions on operating the MP 2000 or require information on specific applications please contact DCA Intertel Phone 31 0 172 604963 or Fax 31 0 172 605237 1 3 Notice The information contained in this document is subj
8. chanics Printer cover is lifted Use the lever to lift the printer mechanics Insert paper and close the printer Intertel Intertel 4 How to Power the suitcase with the red switch left next to the handstrap of the suitcase The switch will indicate it is powered The printer will position itselve in the on line status If error indication on the printer panel is flashing this is indication the internal power is too low Use Car adapter or the 12 VDC power adapter to have good operation and for charging the enclosed batte ry Power on the LapTop Set the data switch to Port Assure the paper is correctly being fixed in the printer Install the MP2000 printer driver on the LapTop For information about printer we refer to the enclosed MP2000 User Manual Intertel 9 Intertel 5 Description 5 1 Printer Overview The MP 2000 Mobile Printer is a ruggedized dot matrix printer designed specifically for mobile and portable applications It can print in graphics mode along with different character fonts both in draft 150 cps and NLQ 25 cps mode It has both tractor and friction feed mechanisms and can print on multi copy paper 1 original and up to 3 copies MP 2000 is particularly suited for portable applications due to its compact size and reduced weight Power requirements have been kept to a minimum bij means of two DC mo tors with integrated optical encoders and an integrated driver board f
9. eady Read 09 Not Connected Not Connected RS232 SERIAL INTERFACE CONNECTORS Intertel 25 Intertel 9 2 Appendix B CHARACTER SET ASCI 256 IBM DEC T HEX Characters control key ASCIIname 000 00 NUL ene n 001 01 50 CtTA startof heading 002 02 STX startoftext 006 06 ACK eCtrF acknowledge 007 07 BEL CtIG bef 009 09 HT ti Yhorizontal tab 010 Joa LF er line feed 011 OB CtrK verticaltab 013 106 CR CrM carriage return 1016 10 DLE Ctrl P___ data Tink escape 018 112 DC2 CR Teontroldevice2 end of transm 025 19 EM jendofmedium 1026 SUB substitute 027 B ESC Cm escape 028 IC FS Ctmy fie seperator Intertel 26 Intertel 9 3 Appendix C DEC ASC DEC ASC DEC ASC DEC ASC NU 32 SP 64 96 1 SOH 33 65 A 97 a 2 S X 34 66 B 98 b 3 ETX 35 6 C 99 c 4 EOT 36 68 100 d 5 ENQ 37 69 E 101 e 6 ACK 38 amp 70 F 10 f 7 BEL 39 71 G 103 g 8 BS 40 72 H 104 h 9 HT 41 73 1 105 i 10 LF 42 74 J 106 j 11 VT 43 75 K 107 k 12 FF 44 76 L 108 13 CR 45 77 M 109 m 14 SO 4 78 N 110 n 15 51 47 79 O ill 16 DLE 48 0 80 P 112 p 17 DC 49 1 81 Q 113 q 18 2 50 2 82 R 114 r 19 DC3 51 3 83 S 115 s 20 DA 52 4 84 T 116 t 21 53 5 85 U 117 u 22 SYN 54 6 86 V 118 v 23 ETB 55 7 87 W 119 w 24 CAN 56 8 8
10. ect to changewithout notice DCA Intertel makes no waranty of any kind with regard to this material and shall not be liable for errors contained herein or for consequential da mages in connection with the furnishing performance or use of this material Intertel 4 Intertel 1 4 Warning This equipment generates uses and can radiate radio frequency energy and may cause interference to radio communications It has been found to comply with the li mits for a Class A computing device pursuant to Subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area may cause such interfe rence that the user may be required to take measures to correct 1 5 Limited Warranty The MP 2000 is warranted against manufacturing defects in material for a period of one year from shipment to the purchaser Within this period DCA Intertel will repair or replace the product without charge for material or la bor Extended warranty is available This warranty does not cover damage or failure caused by abuse improper maintenance or any repairs or modifications other than those provided by DCA Intertel DCA Intertel makes no other warranty either expressed or implied with respect to this product and specifically disclaims the implied war ranties of merchantaility and fitness for a particular pur pose and shall
11. on inter posed should be 0 55 mm 0 05 mm periodic cleaning of the printer s mechanism in order to avoid dust particles paper clips and the like can cause mechanism malfunctions Intertel 23 Intertel 8 7 Replacement Cartridge installation replacement procedure Turn the printer off Remove used cartridge by unlocking bottom latch and then rotating cartridge body upwards as shown by arrow D Place ribbon extender on both studs B until it locks down paying attention to the ribbon not disengaging from the extender itself Gently move the cartridge body along the printing axis and seat it down on its holder C the ribbon should be made to enter partly in the gap between the steel wire ribbon holder and the printhead nose Stretch the inked ribbon by turning knob A counter clockwise Turn the printer on without loading any paper make sure that after the switch on side movement of the printhead the ribbon is properly positioned under printhead s nose Intertel 24 Intertel 9 Interfaces 9 1 Appendix A The printer comes with standard RS 232 Serial Interface 77 SIGNAL SIGNAL Frame Ground 03 smi Data Receive Data eive Data 02 Receive Data eive Data Transmit Data mit Data DSR Data Set Ready DTR Data Terminal 7 5 05 ignal Ground igna Signal Ground round 2 CTS Clear To Send RTS Request To enq RTS Request To CTS Clear To Send enq DTR Data Terminal DSR Data Set R
12. or precise positioning rather than stepping motors MP 2000 has a 2 Kbytes input buffer and comes with an RS 232 serial interface The MP 2000 driver software supports DOS Windows NT Windows 95 and is compatible to the commandset of EPSON LX 400 800 Intertel 10 Intertel 5 2 Printer Layout I ueq 0 340 JOJOWISAI9IS s u 3 MS diq o2eJd huul 9S TLL peog jeuondo A ddng samod pueog 21501 _ ojouu AJ S pieog 4 Mod QVAH YALNIdd o bel 11 Intertel 6 Technical Specifications Weight Power Print Paper Feed Copies Speed Paper Speed Print Width Paper Width Dots Line Char Set Ribbon Life Interface Operating temp Non operating MIL SPEC Intertel 2 2 kg 11 14 0 Volts DC 85 mA Standby 2 5 A at medium print density Impact Dot Matrix 9 pins Bi directional with logic seeking Bi directional Sprocket and friction 1 original 3 copies 150 cps Draft 7 lines second at 1 6 13 lines second continuous 8 25 8 93 pin to pin sprocket 3 5 8 5 tickets 1920 Max IBM graphic bit image Black 1 2 x 106 characters RS 232 5 Cissi 40 C 15 C 70 C 810 D E Shock and Vibration Printer Operation 12 Intertel 7 Installation 7 1 Unpacking Take the printer out of its shipping box and remove any packing material It is advisable to keep the shipping box in case the printer needs
13. to be reshipped or stored elsewhere 7 2 Procedure for Installation 7 2 1Mechanical installation The MP 2000 can print in any position 7 2 2 Driver installation MP 2000 driver software supports DOS Windows NT Windows 95 and is EPSON LX 400 LX 800 compatible and it can therefore be configured as such in the majority of the software packages Intertel 13 Intertel 7 3 Printer Setup The MP 2000 can be configured by using the DIP swit ches as shown in Fig 1 The function of the DIP switches is de picted in Table 1 TABLE 1 DIP SWITCHES Dip Switch Function Baud rate see Table 2 for serial interface ON XON XOFF mode 1 OFF DTR DSR mode U Character set Character set CRLF mode ON enabled l OFF disabled 1 Character set 1 1 NOTE Standard factory setting SW 4 5 6 ON Intertel 14 Intertel TABLE 2 BAUD RATE SELECTION Baud Rate SW 1 1 SW T 2 4800 9600 OFF CRLF mode ON means that after every CR character carriage return sent by the host the printer automati cally performs a LF Line Feed operation STAND BY mode ON means that after a certain pre set inactivity period the printer goes to stand by mode re duced power drain If DIP switch setting is switched ON while the printer is on the new configuration will come into effect only after a subsequent printer turn off and turn on cycle Intertel 15 Intertel
Download Pdf Manuals
Related Search