FX3G-1DA-BD INSTALLATION MANUAL
Contents
1. e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN JY997D33601F MITSUBISHI ELECTRIC PROGRAMMABLE CONTROLLERS MELSEG IF JAPANESE ENGLISH FX3G 1DA BD INSTALLATION MANUAL FX Manual Number JY997D33601 This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and the manuals of all relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions Store this manual in a safe place so that it can be taken out and read whenever necessary Always forward it to the end user Registration The company and product names described in this manual are registered trademarks or the2. Manual name FX3S FX3G FX3GC FX3U FX3UC Series User s Manual Analog Control Edition Description Describes specifications for analog control and programming method for FX3S FX3G FX3GC FX3U FX3UC Series PLC JY997D16701 MODEL CODE 09R619 FX3S Series User s Manual Hardware Edition JY997D48601 MODEL CODE 09R535 Explains FX3S Series PLC specifications for I O wiring installation and maintenance FX3G Series User s Manual Hardware Edition JY997D31301 MODEL CODE 09R521 Explains FX3G Series PLC specifications for I O wiring installation and maintenance How to obtain manuals For product manuals or documents consult with the Mitsubishi Electric dealer from who you purchased your product Applicable standards FX3G 1DA BD units made in November 2008 or later comply with the EC Directive EMC Directive Further information can be found in the following manual FX3S Series Hardware Manual Manual No JY997D48301 FX3G Series Hardware Manual Manual No JY997D46001 Attention e This product is designed for use in industrial applications Note e Authorized Representative in the European Community Mitsubishi Electric Europe B V Gothaer Str 8 40880 Ratingen Germany Caution for EC Directive 1 The The analog expansion boards have been found to be compliant to the European standards in the aforesaid manual and directive However for the very best performance
3. Co Ltd SZS 0 4x2 5 3 2 Wiring of Analog Output For the terminal configuration refer to Section 1 2 Using voltage output Terminal 1 Use 2 core shielded twisted pair cable for the analog output lines and separate the analog output lines from other power lines or inductive lines 2 The grounding resistance should be 100 Q or less 3 3 Grounding Grounding should be performed as stated below e The grounding resistance should be 100 Q or less e Independent grounding should be performed for best results When independent grounding is not performed perform shared grounding of the following figure For details refer to the following manual gt FX3S Series User s Manual Hardware Edition C FX3G Series User s Manual Hardware Edition Other equipment Q Independent grounding Best condition e The grounding wire size should be AWG 22 20 0 3 0 5 mm e The grounding point should be close to the PLC and all grounding wire should be as short as possible Shared grounding Good condition Common grounding Not allowed 4 Specifications STARTUP AND MAINTENANCE PRECAUTIONS CAUTION e Do not disassemble or modify the PLC Doing so may cause fire equipment failures or malfunctions For repair contact your local Mitsubishi Electric representative e Do not drop the product or exert strong impact to it Doing so may cause damage DISPOSAL PRECAUTIONS CAUTION e Pleas
4. M3x8 tapping screws for installation 2 pcs Included items e Side cover e Installation Manual This manual 1 2 External Dimensions Part Names 4 3 2 1 6 Unit mm inches Connector cover is removed 0 6 10 56 Terminal Layout 5 poles 1 Terminal block mounting screws 2 POW LED Lit while power is properly supplied from main unit 3 Mounting holes 2 3 2 4 Connector cover 5 Main unit connector 6 Terminal block to connect analog output 7 Memory cassette Display module connector 2 INSTALLATION PRECAUTIONS Installation WARNING e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product INSTALLATION PRECAUTIONS CAUTION Use the product within the generic environment specifications described in PLC main unit manual Hardware Edition Never use the product in areas with excessive dust oily smoke conductive dusts corrosive gas salt air Cl2 H2S SO2 or NO2 flammable gas vibration or impacts or expose it to high temperature condensation or rain and wind If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur When drilling screw holes or wiring make sure cutting or wire debris does not enter the ventilation slits Failure to do so may cause fire equipme
5. from what are in fact delicate measuring and controlled output device Mitsubishi Electric would like to make the following points As analog devices are sensitive by nature their use should be considered carefully For users of proprietary cables integral with sensors or actuators these users should follow those manufacturers installation requirements Mitsubishi Electric recommend that shielded cables should be used If NO other EMC protection is provided then users may experience temporary loss or accuracy between 10 in very heavy industrial areas However Mitsubishi Electric suggest that if adequate EMC precautions are followed for the users complete control system users should expect accuracy as specified in this manual e Sensitive analog cable should not be laid in the same trunking or cable conduit as high voltage cabling Where possible users should run analog cables separately e Good cable shielding should be used When terminating the shield at Earth ensure that no earth loops are accidentally created e When reading analog values EMC accuracy can be improved out by averaging the readings This can be achieved either through functions on the analog expansion boards or through a users program in the PLC main unit Outline FX3G 1DA BD board hereinafter called 1DA BD is an expansion board for adding one additional analog output point 1 1 Incorporated Items Product Analog output expansion board FX3G 1DA BD e
6. or wire debris does not enter the ventilation slits Failure to do so may cause fire equipment failures or malfunctions Make sure to observe the following precautions in order to prevent any damage to the machinery or accidents due to abnormal data written to the PLC under the influence of noise 1 Do not bundle the power line or shield of the analog input output cable together with or lay it close to the main circuit high voltage line or load line Otherwise noise disturbance and or surge induction are likely to take place As a guideline lay the control line at least 100mm 3 94 or more away from the main circuit high voltage line or load line 2 Ground the shield of the analog input output cable at one point on the signal receiving side However do not use common grounding with heavy electrical systems Make sure to properly wire to the terminal block European type in accordance with the following precautions Failure to do so may cause electric shock equipment failures a short circuit wire breakage malfunctions or damage to the product The disposal size of the cable end should follow the dimensions described in the manual Tightening torque should follow the specifications in the manual Twist the end of strand wire and make sure that there are no loose wires Do not solder plate the electric wire ends Do not connect more than the specified number of wires or electric wires of unspecified size Affix the electri
7. wiring work Failure to do so may cause electric shock or damage to the product INSTALLATION PRECAUTIONS CAUTION Use the product within the generic environment specifications described in PLC main unit manual Hardware Edition Never use the product in areas with excessive dust oily smoke conductive dusts corrosive gas salt air Cl2 H2S SO2 or NO2 flammable gas vibration or impacts or expose it to high temperature condensation or rain and wind If the product is used in such conditions electric shock fire malfunctions deterioration or damage may occur When drilling screw holes or wiring make sure cutting or wire debris does not enter the ventilation slits Failure to do so may cause fire equipment failures or malfunctions Do not touch the conductive parts of the product directly Doing so may cause device failures or malfunctions Connect expansion board securely to their designated connectors Loose connections may cause malfunctions For the installation refer to the following manual FX3S Series User s Manual Hardware Edition FX3G Series User s Manual Hardware Edition 3 Wiring WIRING PRECAUTIONS WARNING e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product WIRING PRECAUTIONS CAUTION e When drilling screw holes or wiring make sure cutting
8. Edition R Read W Write FX This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN
9. FX3G 14ML FX3G 24ML Main units 1 unit FX3G 40ML FX3G 60ML Main units 2 units Never stack up two or more expansion boards For details on the system configuration refer to the following manual FX3S FX3G FX3GC FX3U FX3UC Series User s Manual Analog Control Edition 4 2 General Specifications The general specifications are equivalent to the PLC main unit For general specifications refer to the following manuals FX3S Series User s Manual Hardware Edition FX3G Series User s Manual Hardware Edition 4 3 Performance Specifications Specifications Voltage output O to 10 VDC External load resistance Item Current output 4 to 20 mA DC External load resistance 500 Q or less Analog output range 2 kQ to 1 MQ Digital input 12 bits binary 11 bits binary Resolution 2 5 mV 10 V 4000 8 uA 16 mA 2000 e 0 5 50 mV for full scale of 10 V when ambient temperature is 25 C 5 C 1 0 100 mV for full scale of 10 V when ambient temperature is 0 C to 55 C Shipment adjustment is carried out by external load resistance 2 KQ If external load resistance becomes larger than 2 kQ the output voltage will increase slightly When the load is 1 MQ the output voltage becomes about 2 higher than the correct e 0 5 80 uA for full scale of 16 mA when ambient temperature is 25 C 5 C e 1 0 160 uA for full scale of 16 mA when ambient temperatur
10. JY997D33601F MITSUBISHI ELECTRIC PROGRAMMABLE CONTROLLERS MELSEG IF JAPANESE ENGLISH FX3G 1DA BD INSTALLATION MANUAL FX Manual Number JY997D33601 This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and the manuals of all relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions Store this manual in a safe place so that it can be taken out and read whenever necessary Always forward it to the end user Registration The company and product names described in this manual are registered trademarks or the trademarks of their respective companies Effective April 2015 Specifications are subject to change without notice 2008 Mitsubishi Electric Corporation Safety Precaution Read these precautions before use This manual classifies the safety precautions into two categories and A CAUTION Indicates that incorrect handling may cause hazardous N WARNING conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous conditions resulting in medium or slight personal injury or physical damage Depending on the circumstances procedures indicated by NCAUTION may also cause severe injury It is important to follow all precautions for personal safety Associated Manuals
11. al receiving side However do not use common grounding with heavy electrical systems Make sure to properly wire to the terminal block European type in accordance with the following precautions Failure to do so may cause electric shock equipment failures a short circuit wire breakage malfunctions or damage to the product The disposal size of the cable end should follow the dimensions described in the manual Tightening torque should follow the specifications in the manual Twist the end of strand wire and make sure that there are no loose wires Do not solder plate the electric wire ends Do not connect more than the specified number of wires or electric wires of unspecified size Affix the electric wires so that neither the terminal block nor the connected parts are directly stressed Make sure to properly wire to the terminal blocks in accordance with the following precautions Failure to do so may cause electric shock equipment failures a short circuit wire breakage malfunctions or damage to the product The disposal size of the cable end should follow the dimensions described in the manual Tightening torque should follow the specifications in the manual 3 1 Applicable Cable and Terminal Tightening Torque 3 1 1 Terminal block European type 1 Wire size Wiring to analog device should use 20 22 AWG wire 2 Applicable cable Type Wire size Single wire 0 3 mm2 to 0 5 mm AWG22 to 20 2 wire 2 pieces of 0 3
12. are Edition FX3G Series User s Manual Hardware Edition Other equipment Q Independent grounding Best condition e The grounding wire size should be AWG 22 20 0 3 0 5 mm e The grounding point should be close to the PLC and all grounding wire should be as short as possible Shared grounding Good condition Common grounding Not allowed 4 Specifications STARTUP AND MAINTENANCE PRECAUTIONS CAUTION e Do not disassemble or modify the PLC Doing so may cause fire equipment failures or malfunctions For repair contact your local Mitsubishi Electric representative e Do not drop the product or exert strong impact to it Doing so may cause damage DISPOSAL PRECAUTIONS CAUTION e Please contact a certified electronic waste disposal company for the environmentally safe recycling and disposal of your device TRANSPORTATION AND STORAGE PRECAUTIONS CAUTION e The product is a precision instrument During transportation avoid any impacts Failure to do so may cause failures in the product After transportation verify the operations of the product 4 1 Applicable PLC Model name Applicability FX3S Series PLC Ver 1 00 or later from first production FX3G Series PLC Ver 1 10 or later The version number can be checked by monitoring D8001 D8101 as the last three digits indicate it e The number of connectable expansion boards varies depending on the main unit as follows FX38
13. c wires so that neither the terminal block nor the connected parts are directly stressed Make sure to properly wire to the terminal blocks in accordance with the following precautions Failure to do so may cause electric shock equipment failures a short circuit wire breakage malfunctions or damage to the product The disposal size of the cable end should follow the dimensions described in the manual Tightening torque should follow the specifications in the manual 3 1 Applicable Cable and Terminal Tightening Torque 3 1 1 Terminal block European type 1 Wire size Wiring to analog device should use 20 22 AWG wire 2 Applicable cable Type Wire size Single wire 0 3 mm2 to 0 5 mm AWG22 to 20 2 wire 2 pieces of 0 3 mm2 AWG22 3 Termination of cable end Strip the coating of strand wire and twist the cable core before connecting it or strip the coating of single wire before connecting it An alternative connection is to use a ferrule with insulating sleeve lt Reference gt Manufacturer Caulking tool CRIMPFOX 6 1 or CRIMPFOX 6T F Al 0 5 8WH 1 Old model name CRIMPFOX ZA 3 2 Old model name CRIMPFOX UD 6 Phoenix Contact Co Ltd Stick terminal with insulating sleeve Insulation sleeve Contact area Crimp area SS tc 0 35 2 6mm 0 1 Strand wire single wire When using a stick terminal with insulating sleeve choose a wire with proper cable sheath referring to th
14. e is 0 C to 55 C Total accuracy value Rees 60 us tim The data will be updated at every scan time of the PLC 0 to 4000 are adjusted to 0 to 0 to 2000 are adjusted to 4 to 10 V when the external load 20 mA when the external load resistance is 2 kQ resistance is 250 Q 10V 20mA Z gt jad D gt O v fi output amp characteristics o 4mA ne S 0 gt 4000 4080 g 2000 2040 Digital input Digital input Caution An area of dead band is located in the region of 0 V Therefore the output analog value may not represent the digital value accurately Insulation No insulation between the PLC method Occupied 0 point This number is not related to the maximum number of points input output points of the PLC 4 4 List of Special Devices Device number FX3G Description R W S Switches the output mode MBABU MRED i Morg OFF Voltage output ON Current output PAN Special A Holding Function Cancellation auxiliary l relay m8264 m8264 m8274 OF e e pa ia R W ON Output the offset data at stop of the PLC D8260 D8260 D8270 Output setting data R W Error status b0 Output data setting error Special b1 Unused data D8268 D8268 D8278 b2 Unused R W register b3 Unused b4 EEPROM error b15 to b5 Unused R As for the details of the special devices refer to the following manual FX3S FX3G FX3GC FX3U FX3UC Series User s Manual Analog Control
15. e above outside dimensions or otherwise the wire cannot be inserted easily The tightening torque must be 0 22 to 0 25 Nem Do not tighten terminal screws exceeding the specified torque Failure to do so may cause equipment failures or malfunctions 4 Tool For tightening the terminal use a commercially available small screwdriver having a straight form that is not widened toward the end as shown With straight tip right 2 5mm Caution gt eOr If the diameter of screwdriver grip is too small tightening torque will not be able to be achieved Use the following recommended screwdriver or an appropriate replacement grip diameter approximately 25 mm 0 98 lt Reference gt Manufacturer Phoenix Contact Co Ltd SZS 0 4x2 5 3 2 Wiring of Analog Output For the terminal configuration refer to Section 1 2 Using voltage output Terminal Use 2 core shielded twisted pair cable for the analog output lines and separate the analog output lines from other power lines or inductive lines 2 The grounding resistance should be 100 Q or less 3 3 Grounding Grounding should be performed as stated below e The grounding resistance should be 100 Q or less e Independent grounding should be performed for best results When independent grounding is not performed perform shared grounding of the following figure For details refer to the following manual FX3S Series User s Manual Hardw
16. e contact a certified electronic waste disposal company for the environmentally safe recycling and disposal of your device TRANSPORTATION AND STORAGE PRECAUTIONS CAUTION e The product is a precision instrument During transportation avoid any impacts Failure to do so may cause failures in the product After transportation verify the operations of the product 4 1 Applicable PLC Model name Applicability FX3S Series PLC Ver 1 00 or later from first production FX3G Series PLC Ver 1 10 or later The version number can be checked by monitoring D8001 D8101 as the last three digits indicate it e The number of connectable expansion boards varies depending on the main unit as follows FX3s FX3G 14ML FX3G 24ML Main units 1 unit FX3G 40ML FX3G 60ML Main units 2 units Never stack up two or more expansion boards For details on the system configuration refer to the following manual FX3S FX3G FX3GC FX3U FX3UC Series User s Manual Analog Control Edition 4 2 General Specifications The general specifications are equivalent to the PLC main unit For general specifications refer to the following manuals FX3S Series User s Manual Hardware Edition FX3G Series User s Manual Hardware Edition 4 3 Performance Specifications Specifications Voltage output 0to10 VDC External load resistance Item Current output 4 to 20 mA DC External load resistance 500 Q or less Analog output ran
17. er from who you purchased your product Applicable standards FX3G 1DA BD units made in November 2008 or later comply with the EC Directive EMC Directive Further information can be found in the following manual FX3S Series Hardware Manual Manual No JY997D48301 FX3G Series Hardware Manual Manual No JY997D46001 Attention e This product is designed for use in industrial applications Note e Authorized Representative in the European Community Mitsubishi Electric Europe B V Gothaer Str 8 40880 Ratingen Germany Caution for EC Directive The analog expansion boards have been found to be compliant to the European standards in the aforesaid manual and directive However for the very best performance from what are in fact delicate measuring and controlled output device Mitsubishi Electric would like to make the following points As analog devices are sensitive by nature their use should be considered carefully For users of proprietary cables integral with sensors or actuators these users should follow those manufacturers installation requirements Mitsubishi Electric recommend that shielded cables should be used If NO other EMC protection is provided then users may experience temporary loss or accuracy between 10 in very heavy industrial areas However Mitsubishi Electric suggest that if adequate EMC precautions are followed for the users complete control system users should expect accuracy as speci
18. fied in this manual e Sensitive analog cable should not be laid in the same trunking or cable conduit as high voltage cabling Where possible users should run analog cables separately e Good cable shielding should be used When terminating the shield at Earth ensure that no earth loops are accidentally created e When reading analog values EMC accuracy can be improved out by averaging the readings This can be achieved either through functions on the analog expansion boards or through a users program in the PLC main unit 1 Outline The FX3G 1DA BD board hereinafter called 1DA BD is an expansion board for adding one additional analog output point 1 1 Incorporated Items Product Analog output expansion board FX3G 1DA BD e M3x8 tapping screws for installation 2 pcs e Side cover e Installation Manual This manual Included items 1 2 External Dimensions Part Names Unit mm inches 4 Connector cover is removed 3 2 1 0 6 10 56 6 Terminal Layout 5 poles 1 Terminal block mounting screws 2 POW LED Lit while power is properly supplied from main unit 3 Mounting holes 2 3 2 4 Connector cover 5 Main unit connector 6 Terminal block to connect analog output 7 Memory cassette Display module connector 2 Installation INSTALLATION PRECAUTIONS WARNING e Make sure to cut off all phases of the power supply externally before attempting installation or
19. ge 2 kQ to 1 MQ Digital input 12 bits binary 11 bits binary Resolution 2 5 mV 10 V 4000 8 uA 16 mA 2000 e 0 5 50 mV for full scale of 10 V when ambient temperature is 25 C 5 C 1 0 100 mV for full scale of 10 V when ambient temperature is 0 C to 55 C Shipment adjustment is carried out by external load resistance 2 KQ If external load resistance becomes larger than 2 kQ the output voltage will increase slightly When the load is 1 MQ the output voltage becomes about 2 higher than the correct e 0 5 80 pA for full scale of 16 mA when ambient temperature is 25 C 5 C e 1 0 160 uA for full scale of 16 mA when ambient temperature is 0 C to 55 C Total accuracy value a 60 us time The data will be updated at every scan time of the PLC 0 to 4000 are adjusted to 0 to 0 to 2000 are adjusted to 4 to 10 V when the external load 20 mA when the external load resistance is 2 kQ resistance is 250 Q 10V 20mA D gt jab D gt D output o e characteristics o 4mA 0 4000 4080 amp gt 2000 2040 Digital input Digital input Caution An area of dead band is located in the region of 0 V Therefore the output analog value may not represent the digital value accurately Insulation No insulation between the PLC method Occupied 0 point This number is not related to the maximum number of points input outp
20. mm2 AWG22 3 Termination of cable end Strip the coating of strand wire and twist the cable core before connecting it or strip the coating of single wire before connecting it An alternative connection is to use a ferrule with insulating sleeve lt Reference gt Manufacturer Caulking tool CRIMPFOX 6 1 or CRIMPFOX 6T F Al 0 5 8WH 1 Old model name CRIMPFOX ZA 3 2 Old model name CRIMPFOX UD 6 Phoenix Contact Co Ltd Stick terminal with insulating sleeve Insulation sleeve Contact area Crimp area SS tc 0 35 2 6mm 0 1 Strand wire single wire When using a stick terminal with insulating sleeve choose a wire with proper cable sheath referring to the above outside dimensions or otherwise the wire cannot be inserted easily The tightening torque must be 0 22 to 0 25 Nem Do not tighten terminal screws exceeding the specified torque Failure to do so may cause equipment failures or malfunctions 4 Tool For tightening the terminal use a commercially available small screwdriver having a straight form that is not widened toward the end as shown With straight tip right 2 5mm Caution gt eOr If the diameter of screwdriver grip is too small tightening torque will not be able to be achieved Use the following recommended screwdriver or an appropriate replacement grip diameter approximately 25 mm 0 98 lt Reference gt Manufacturer Phoenix Contact
21. nt failures or malfunctions Do not touch the conductive parts of the product directly Doing so may cause device failures or malfunctions Connect expansion board securely to their designated connectors Loose connections may cause malfunctions For the installation refer to the following manual FX3S Series User s Manual Hardware Edition FX3G Series User s Manual Hardware Edition 3 Wiring WIRING PRECAUTIONS WARNING e Make sure to cut off all phases of the power supply externally before attempting installation or wiring work Failure to do so may cause electric shock or damage to the product WIRING PRECAUTIONS CAUTION e When drilling screw holes or wiring make sure cutting or wire debris does not enter the ventilation slits Failure to do so may cause fire equipment failures or malfunctions Make sure to observe the following precautions in order to prevent any damage to the machinery or accidents due to abnormal data written to the PLC under the influence of noise 1 Do not bundle the power line or shield of the analog input output cable together with or lay it close to the main circuit high voltage line or load line Otherwise noise disturbance and or surge induction are likely to take place As a guideline lay the control line at least 100mm 3 94 or more away from the main circuit high voltage line or load line 2 Ground the shield of the analog input output cable at one point on the sign
22. trademarks of their respective companies Effective April 2015 Specifications are subject to change without notice 2008 Mitsubishi Electric Corporation Safety Precaution Read these precautions before use This manual classifies the safety precautions into two categories and A CAUTION Indicates that incorrect handling may cause hazardous N WARNING conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous NCAUTION conditions resulting in medium or slight personal injury or physical damage Depending on the circumstances procedures indicated by NCAUTION may also cause severe injury It is important to follow all precautions for personal safety Associated Manuals Manual name FX3S FX3G FX3GC FX3U FX3UC Series User s Manual Analog Control Edition Description Describes specifications for analog control and programming method for FX3S FX3G FX3GC FX3U FX3UC Series PLC JY997D16701 MODEL CODE 09R619 JY997D48601 MODEL CODE 09R535 FX3S Series User s Manual Hardware Edition Explains FX3S Series PLC specifications for I O wiring installation and maintenance JY997D31301 MODEL CODE 09R521 FX3G Series User s Manual Hardware Edition Explains FX3G Series PLC specifications for I O wiring installation and maintenance How to obtain manuals For product manuals or documents consult with the Mitsubishi Electric deal
23. ut points of the PLC 4 4 List of Special Devices Device number FX3G Description R W Switches the output mode MEZGO MGAGO Me270 OFF Voltage output ON Current output RW Special eine Holding Function Cancellation auxiliary relay OFF Holds the analog data output just M8264 M8264 M8274 before stop of the PLC R W ON Output the offset data at stop of the PLC D8260 D8260 D8270 Output setting data R W Error status bO Output data setting error Special b1 Unused data D8268 D8268 D8278 b2 Unused R W register b3 Unused b4 EEPROM error b15 to b5 Unused R As for the details of the special devices refer to the following manual FX3S FX3G FX3GC FX3U FX3UC Series User s Manual Analog Control Edition R Read W Write FX3S This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi opportunity loss or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties
Download Pdf Manuals
Related Search