RELEA ASE NO OTES
Contents
1. During restart data transfer drops for about 35 sec o Log again with ADMIN rights and update start up memory configuration with the newest functional setting available in the newest firmware Save the current newest configuration by clicking Write_W0O button which is available on each page or by using menu Maintenance Write o Make new IDU initialization from the start up memory Select Run_ WO0 from menu Maintenance Write During initialization there is data drop for about 5 sec e New firmware is now properly installed in the IDU FIXES AND ENHANCEMENTS Wideband design 303 function Wideband design 303 could start in mode without internal switch FIFO support In this case any longer burst of packet at IDU input causes drop in such stream This malfunction is repaired in this revision WEB based VLAN configuration VLAN configuration entered via WEB GUI is always replaced by original setting run w0 after 30 seconds independently whether Confirm button is pressed or not Therefore it is not possible to set permanent VLAN changes over WEB GUI This procedure is corrected and VLAN setting over WEB GUI is now fully supported Adaptive modulation improvement Solves adaptive modulation that was not able to set lower modulation in some conditions Implements new kernel which allows for faster synchronization This change provides better and more reliable functionality of ACM and decreases time needed to connection re establishing Add2. www proxim com RELEASE NOTES Tsunami GX800 Series Software Release v2 0 pro gt lt im wireless RECOMMENDED STEPS FOR FIRMWARE UPDATE Please perform the following steps for correct firmware update e Login over web browser with ADMIN rights e Save currently running configuration by clicking Write _WO0 button which is available on each page or by using menu Maintenance Write The startup memory will then contain the actual configuration e Compare the currently running versions of each firmware parts os_kernel os_dev hw_base and fw_base with the newest version by one of the two below given steps o Manually compare data shown in menu General Revision with new firmware description file version txt o Open menu Maintenance FW Upgrade select file checkversions afw and use the print out for information on what parts should be upgraded e Next choose one of the following steps o Select file fw_all afw from the provided SW package The whole file will be uploaded into the device then the system compares the different versions and writes needed firmware part into flash memory l This procedure is not suitable for slow connection to IDU management o Gradually select files hwbase afw oskernel afw dev afw and fwbase afw in this order if one file is not needed please continue with the next file until process completion e After the last file upload o restart the device from menu Maintenance Miscellaneous REBOOT DEVICE
3. RELEASE NOTES Tsunami GX800 Series Software Release v2 0 proxim wireless Tsunami GX800 Series Software Release v2 0 INTRODUCTION Welcome to software release v2 0 of the Tsunami GX800 product family This software release adds enhancements and addresses minor software bugs to the application code running in the IDUs of the GX800 product family lt p vn Tsunami GX800 6U 6LGHz Microwave Link Series Tsunami GX800 7 GHz Microwave Link Series Yes Tsunami GX800 8 GHz Microwave Link Series Yes Tsunami GX800 10 11 GHz Microwave Link Series Yes Tsunami GX800 13 GHz Microwave Link Series Yes Tsunami GX800 15 GHz Microwave Link Series Yes Tsunami GX800 18 GHz Microwave Link Series Yes Tsunami GX800 23 GHz Microwave Link Series Yes UPGRADE DOWNGRADE TO FROM PREVIOUS SOFTWARE RELEASE This release is compatible for upgrade from v1 0 b0209 03 software releases COMPONENTS IDU firmware is divided into four sections in dependence on their functions For every firmware release it is not necessary to update all the parts but only these ones which are different comparing to the newest version There is basic firmware parts description in the following text e hwbase afw software for internal HW parts e oskernel afw operating system e dev afw drivers for OS e fwhase afw application software WEB SNMP commands etc All rights reserved 1 2012 Proxim Wireless Corporation 765 00156 1
4. pped ODUs L and H units are swapped against IDU setting HELP information Correction in the help node of Ports Enhanced page ENH string is replaced by FIFO string Correction in the help node of Maintenance Refresh page Help message is reformulated Actualization of CLI user manual can be accessed via sh man command Correction of URL link function during system reboot from the Maintenance Miscellaneous menu Secure FTP access Password was not accepted without at least one char in it This issue is solved Alarm threshold ODU temp alarm threshold has been increased Modem Lock Fix of error in program code which prevented IDU from establishing a modem lock in case when the Low Latency Mode was used together with QAM 128 or QAM256 and 56Mhz BW All rights reserved 3 2012 Proxim Wireless Corporation www proxim com RELEASE NOTES Tsunami GX800 Series Software Release v2 0 pro gt lt im wireless WHERE CAN GET ADDITIONAL INFORMATION For the latest software and documentation go to http support proxim com For additional information or questions about Proxim products visit www proxim com Proxim Wireless Corporation 1561 Buckeye Drive Milpitas CA 95035 All rights reserved 4 2012 Proxim Wireless Corporation www proxim com
5. s option to choose how many Error Free Seconds EFS is required until change to higher ACM modulation All rights reserved 2 2012 Proxim Wireless Corporation www proxim com RELEASE NOTES Tsunami GX800 Series Software Release v2 0 prom wireless SNMP and MIB enhancement Adds new entries into the MIB file extended ath_products_wfmHs mib Fixes SNMP strings malfunction infoFceDatEthA1 and infoFceDatEthB1 Tx power level Display When modulation changes from high Tx power modulation QPSK to lower Tx power modulation 128QAM Tx power level display does not reflect real Tx power used by ODU This issue is fixed and actual Tx power level now displays the correct value Warning messages modification New message after VLAN change New message after IP change Log file startup file and license file backup is fully supported when FTP link is specified in FTP USB server parameter at IP Address page in WEB GUI It is also possible to extend FTP specification by specific ftp user password syntax Fix of the set mod mute command The mute command has been automatically abandoned after 2 3 seconds This issue is now fixed User privilege Removed Accept and Undo buttons in menu Ports Advanced which are not relevant for user account Added option to assign additional privileges to Guest account specifically rights to clear and validate alarms User logged under user account cannot perform correct repair of ODU Tx Frequency for swa
Download Pdf Manuals
Related Search