SC733 MANUAL_rc
Contents
1. Note refer to the layouts Pages 1 5 1 7 for the LED and Jumper Locations 1 8 4 SCSI Super GEM Driver Installation Instructions for the Windows Operating System Please refer to the following instructions to install the SCSI GEM Driver for the Windows OS systems Note This driver is not necessary for other Operating Systems If you have two SCA backplanes you will need to install the driver twice The driver is located on the Super Micro motherboard driver CD or is available for download from our FTP site ftp ftp supermicro com driver Alogic Follow the procedure below to install this driver to your system Installing the driver 1 Right click on My Computer and choose Property 2 Select Hardware tab and click on Device Manager 3 Open Other Devices or wherever GEM318 is on 4 Right click on this device and choose Property 5 Click on Driver tab and choose Update Driver 6 Click Next 2 times uncheck both Floppy disk drives and CD ROM drives Then select the item Specify a location and choose Next 7 Click on Browse and choose D drive or wherever Supermicro Setup CD is in 8 Choose Qlogic folder and click on Open 9 System will automatically detect GEM318 and install the drive from this point on or 1 Right click the My Computer icon on your desktop and choose Proper tie2. CSE SCA 833S2 Backplane USER S GUIDE Rev 1 0b SUPER CSE SCA 833S2 Backplane User s Guide The information in this User s Manual has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com SUPERMICRO COMPUTER reserves the right to make changes to the product described in this manual at any time and without notice This product including software if any and documentation may not in whole or in part be copied photocopied reproduced translated or reduced to any medium or machine without prior written consent IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the Sta
3. ES E 2 8 8 5 FORO ee E D5 D12 pe 21 D14 D27 0260174015 _ 020 023 D2 1024 said U Rear View See below for the rear connector description Please also refer to the next page for LED information Connector Descriptions Location Description SCA1 SCA Channel A ID 0 SCA8 SCA Channel A ID 1 SCA2 SCA Channel A ID 2 SCA3 SCA Channel A ID 3 SCA4 SCA Channel B ID 0 SCA5 SCA Channel B ID 1 SCA6 SCA Channel B ID 2 SCA7 SCA Channel B ID 3 1 7 SUPER9CSE SCA 833S2 Backplane User s Guide 3 LED Indicators Front LED Indicators LED _ Activity D4 LED Red light flashing Overheat or Drive Fail Buger On D37 LED Red light On Fan1 Fail Bazena Buzzer On D41 LED Red light On Fan3 Fail Buzzer On Rear LED Indicators Note For all Drive Failure LEDs Red light On indicating Drive Failure Red light flashing indicating RAID Rebuilding LED Description 012 SCA ActviyLED De SCAFZ Fail LED See Note above D13 _ SCAHZActviyLED 00 014 SCA ActviyLED 026 SCAM ActviyLED D15 SCAS Actviy LED D20 SCA 6 Actviy LED D21 SCA 7 Actviy LED D24 SCAS Aciviy ED SAF TE LED Indicators D4 Front Overheat or Drive Failure pen 7 i aoa buzzer on D6 Rear SCA 2 Fail LED See Note above SCA 3 Fail LED See Note above SCA 4 Fail LED See Note above
4. Safety Guidelines Electric Static Discharge ESD can damage electronic components To prevent damage to your system itis important to handle it very carefully The following measures are generally sufficient to protect your eguipment from ESD Use a grounded wrist strap designed to prevent static discharge Touch a grounded metal object before removing a component from the antistatic bag Handle the Backplane by its edges only do not touch its components peripheral chips memory modules or gold contacts When handling chips or modules avoid touching their pins Put the card and peripherals back into their antistatic bags when not in use General Safety Guidelines Always disconnect power cables before installing or removing any com ponents from the computer including the SCA 83352 Backplane Disconnect the power cable before installing or removing any cable from the SCA 83352 Backplane Make sure that the SCA 83352 Backplane is securely and properly installed on the motherboard to prevent damage to the system due to power shortage An Important Note to the User All images and layouts shown in this user s guide are based upon the PCB Rev 1 00 which is the latest version available at the time of publishing The card you ve received may or may not look exactly the same as the images or the layouts shown in this manual 1 4 Technical Specifications 2 Technical Specifications 2A Fr
5. fined SCSI commands to monitor the status of disk drives and provide disk drive information to the user through LED indicators and buzzers Note This func tion is available only when a RAID control ler with a RAID set is present and enabled Please refer to Page 1 8 for more informa tion on SAF TE LED Indicators Front Jumper Descriptions and Pin Descriptions Jumper Setting Description _____________ IP Open Channel A Delay Stat IP22 Open Channel ARemoteStat IP20 Open Channel B Delay Sa IP23 Open Channel B Remote Sat JP41 Fan 1 using Onboard fan Enable Open Fani Disable JP42 Fan 2 using Onboard fan Enable Fan 2 Disable JP43 Closed Default Fan 3 using Onboard fan Enable Open Fan 3 Disable JP Open BuzzerReset SS Note Press the button on the front panel once to disable the buzzer If the buzzer has been disabled please be sure to press the button once again to re enable the buzzer Note refer to the layout on the previous page for the LED and Jumper Locations Please refer to Page 1 8 for LED information 1 6 Rear Connectors and LED Locations 2B Rear Connectors and LED Locations Rear Connector LED Indicator Locations ER ER E SCA1 SCA8 SCA2 SCA3 SCA4 SCA5 SCA6 SCA7 wm wm QTE Ho Hip HHS eo Ee o 9 Hig Es 4 Q ES z 4 z 2 8 ta e a ES gt a D _ 5 w oO oO S ES
6. ont Jumpers Connectors and LED Indicators Front Jumper Connector LED Locations Front View EE puen i Ia ls OE e el 0 E im TSEEBVDS KING E O p PEW ee og G FE 41 DB e See below for the front connector LED descriptions A SCA Channel A In LVD1 B SCA Channel B In LVD2 C D Backplane Power Connectors JP10 JP15 You must use both 4 pin power con Channel AB EWR nectors marked C and D on the 4 pin Connectors layout above to provide adequate Bina a oenen power supply to the backplane See 1 12V the table on the right for pin defini eae ees tions Note To provide adequate power supply to the backplane both power connectors are required SUPER CSE SCA 833S2 Backplane User s Guide E Fan1 JP33 F Fan2 JP34 G Fan3 JP35 3 pin Fan Header Pin Definitions The SCA833S2 has three fan headers Fan Header Pin Definitions Designations include Fan1 JP33 Fan2 Bin JP34 and Fan3 JP35 See the table Number Definition i i nes 1 Ground black on the right for pin definitions 2 12V red 3 Tachometer Caution These fan headers H I GEM 318 SAF TE SCSI Accessed are DC power Fault Tolerant Enclosures These chips allow the system to use a set of pre de
7. s 2 Click on the Hardware tab and click on Device Manager to bring up the list of system devices 3 You may see one or two yellow question marks that read QLogic GEM354 or GEM318 SCSI Processor Device Right click on these and choose to uninstall If two such question marks are present uninstall both 4 Click on Action tab and choose Scan for Hardware Changes The Hardware Wizard program should start up Click Next 5 At the first prompt choose Display a list of known device drivers for the device so that can choose a specific driver and click Next 6 Choose Other Devices and click Next 7 Choose Have Disk and specify your floppy drive location in the options box Then click Next 8 Highlight Enclosure Services Device and click Next 9 Ignore the warning prompt by clicking Yes 1 9 SUPER CSE SCA 833S2 Backplane User s Guide Notes
8. te of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Supermicro s total liability for all claims will not exceed the price paid for the hardware product Unless you request and receive written permission from SUPER MICRO COMPUTER you may not copy any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2005 by SUPER MICRO COMPUTER INC All rights reserved Printed in the United States of America 1 2 Table of Contents Table of Contents 1 Safety Guidelines e nornnnenennenanannnnennnaenanannnnnnannnnnanannannnana 1 4 2 Technical Specifications naernnennnnnnnnannnannnnannnannnnanannnnana 1 5 2A Front Jumpers Connectors and LED Indicators 1 5 2B Rear Connectors and LED Locations 1 1 7 3 LED IMdIGALOKS eitava v kke a aa oc aaa conu aaa aa Danae ata aaa aia pa 1 8 4 SCSI GEM Driver Installation for the Windows OS 1 9 1 3 SUPER CSE SCA 833S2 Backplane User s Guide 1 Safety Guidelines To avoid personal injury and property damage please carefully follow all the safety steps listed below when accessing your system or handling the components ESD
Download Pdf Manuals
Related Search