BLUETOOTH AUDIO RECEIVER/TRANSMITTER
Contents
1. D flashes twice every 4 seconds Connected to a device Red LED flashes Low power m RX Mode Selecting mode Please turn the TX RX switch to RX mode before switching on DA 30501 Note TX or RX mode cannot be changed after switching on DA 30501 1 Switching on off the receiver LED indicator Switching on Press 1 button for 3 4 Blue LED is on for 1 receiver seconds second Switching off Press O button for 3 4 Red LED is on for 1 receiver seconds second and then off 2 Pairing with Bluetooth devices How to enter pairing mode Function Operation _ Entering pairing mode Make sure the receiver is off press and hold O button for about 5 7 seconds and do not release it until red and blue LEDs flashes alternately Note The pairing mode will last 2 minutes The receiver will automatically switch to standby mode if no devices can be connected within 2 minutes Pairing with a Bluetooth cell phone Please make sure your cell phone is Bluetooth enabled Specific pairing steps may vary with different models of cell phones Please refer to your cell phone s user s manual for further information The general pairing steps are as follows 1 Keep the receiver and Bluetooth cell phone within 1 meter when pairing 2 Enter the receiver s pairing mode refer to How to enter pairing mode 3 Active your cell phone s Bluetooth function and set your cell phone to search for Bluetooth devices within range After the se2. arch is completed select DA 30501 from the list of devices shown 4 According to the indication enter password or PIN No 0000 5 If prompted by your cell phone to connect select Yes 6 After successful connecting blue LED of the receiver will flash twice every 4 seconds Notes If the pairing is failed please switch off the receiver and re pair according to steps 1 6 mentioned above After pairing is successful the receiver and the cell phone will remember each other they will no need to re pair next time The receiver can remember 8 paired devices when the number of paired devices exceeds 8 the first one will be replaced Every time the receiver is switched on it will connect to the last connected device automatically If you want to pair it to other devices please turn off the current device s Bluetooth function first and try to pair the receiver to the new device according to steps 1 6 mentioned above 3 Listening to music When DA 30501 is used as a receiver you can connect it to a 3 5mm stereo headset or stereo speaker with a 3 5mm to 3 5mm audio cable Now you can listen to music and control pause play of music Status of the receiver Pause Playing music Short press O button once Short press button once 4 Reconnecting to a Bluetooth device 1 Automatic connecting Every time the receiver is switched on it will automatically connect to last connected device 2 Manual connecti
3. eiver When it is used as a Bluetooth transmitter it can be connected to your walkman or PC to wirelessly transmit the music to your Bluetooth stereo receiver Such as Bluetooth stereo headset Bluetooth stereo speaker and so on When it is used as a Bluetooth receiver it can be connected to your common stereo receiver for wireless playing music from your Bluetooth audio player 2 System requirements a When DA 30501 is used as a Bluetooth transmitter you need to prepare a audio player with 3 5mm audio out jack and a Bluetooth A2DP receiver such as Bluetooth stereo headset Bluetooth stereo speaker and so on When DA 30501 is used as a Bluetooth receiver you need to prepare a stereo receiver with 3 5mm audio in jack and a Bluetooth A2DP transmitter such as Bluetooth cell phone Bluetooth MP3 and so on b 3 Overview Multi function button MFB 3 5mm audio jack Switching on off pairing 3 5mm to 3 5mm audio cable LED indicator 2 Charging jack 5 TX RX switch E Getting started 1 Charging the battery of DA 30501 DA 30501 comes with a built in rechargeable battery prior to using it it is recommended to charge the battery fully for the first time When DA 30501 is low power red LED flashes Please recharge the battery of DA 30501 Connect the charger to a standard power outlet and the charger plug to the charging jack of DA 30501 Red LED is on while charging It takes about 3 hours to charge the batte
4. ght get damaged In case the headset doesn t function properly send it to the store you bought it The staff will help you to solve the problem 6 m FAQs 1 What to do when DA 30501 can t be switched on Please charge it 2 What to do when DA 30501 can t pair and connect to a Bluetooth device 1 Make sure Bluetooth stereo receiver supports A2DP 2 Make sure Bluetooth stereo receiver is placed within 5 meters 3 Make sure Bluetooth stereo receiver has already entered into pairing mode 3 What to do when DA 30501 can t be switched off Please charge it for about 2 seconds m Specifications Dimensions 51 4x347x86mm Weight BSG Working time TX Up to 11 hours Notes 1 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment
5. ice every 4 seconds Connect the transmitter to your music player through 3 5mm audio jack to play music 4 s Notes 3 The pairing mode will last 2 minutes The transmitter will enter standby mode if no devices can be connected within 2 minutes The transmitter can pair with a Bluetooth stereo receiver whose PIN number is 0000 1234 or 1111 8888 Reconnecting to a Bluetooth device 1 Automatic connecting Every time the transmitter is switched on it will automatically connect to last connected device 2 Manual connecting When the Uno is in standby mode and doesn t connect to any devices short press O button once it will automatically connected to last connected device 3 Can be connected In addition when the transmitter is in standby mode and doesn t connect to any devices it can accept the connecting request sent by the receiver that has already been paired with the transmitter before 4 Auto off The transmitter will automatically switch off if no devices can be connected within 5 minutes 5 Clearing pairing list Make sure the transmitter is off press and hold O button for about 10 seconds and don t release it until red LED is on for 1 second and then blue LED is on for 1 second 6 LED indicator LED indicator Status of the transmitter Blue LED flashes continuously Blue LED flashes once every 1 second Standby mode and not connected to a device Blue LE
6. ng When the receiver is in standby mode and doesn t connect to any devices short press button once it will automatically connected to last connected device 5 Auto off The receiver will automatically switch off if no devices can be connected within 5 minutes 6 Clearing pairing list Make sure the receiver is off press and hold O button for about 10 seconds and don t release it until red LED is on for 1 second and then blue LED is on for 1 second 7 LED indicator LED indicator Status of the receiver Red and blue LEDs flash alternately Blue LED flashes once every 1 second Standby mode and not connected to a device Blue LED flashes twice every 4 seconds Connected to a device Red LED flashes Care and maintenance Before using DA 30501 please read the following recommendations it will help you to enjoy the product for many years Do not expose the product to liguid moisture or humidity to avoid the product s internal circuit being affected Do not expose the product to extremely high or low temperature as this will shorten the life of electronic devices destroy the battery or distort certain plastic parts Don t use abrasive cleaning solvents to clean the product Don t dispose of the product in a fire as it will result in an explosion Don t expose the product to contact with sharp objects as this will cause scratches and damage Don t let the product fall down onto the floor The internal circuit mi
7. penus BLUETOOTH AUDIO RECEIVER TRANSMITTER Quick Installation Guide DA 30501 Contents E Before Usei 1 0 BOA DASSOSON maa tata Tad drat 2 System requirements Avene m Getting started seistes iii 1 Charging the battery of DA 30501 M TX MOG aaa na A jaa kaani makku 1 Switching on off the sis si s it 2 Pairing with a Bluetooth device n 3 Reconnecting to a Bluetooth AA Ott ajalises laad ala aal 5 Clearing pairing IS ae eet to ee eee A A aaa Ant 6 LED indicato i iii riali W a laica 1 Switehing on off theTeceiveri lil calivle iene nia 2 Pairing witha Bluetoothidevicei iaia 3 How to enter pall NGIMOdE ciare 4 Pairing with a Bluetooth cell phone n Listening a 6 Reconnecting to a Bluetooth eae STi ea ce 8 Clearing pairing 9 LED indicator Thank you for using Digitus Bluetooth Audio Receiver Transmitter DA 30501 Please read this user s manual carefully before use W Before use 1 About DA 30501 DA 30501 is a Bluetooth transmitter and rec
8. ry fully When charging is completed red LED will be off Note Please don t attempt to take out battery from DA 30501 in case of damaging DA 30501 49 a Warning 1 The battery is recyclable 2 Do not dispose of the battery in fire as it may cause explosion m TX Mode Selecting mode Please turn the TX RX switch to TX mode before switching on DA 30501 Note TX or RX mode cannot be changed after switching on DA 30501 1 Switching on off the transmitter LED indicator Switching on Press 1 button for 3 4 Blue LED is on for transmitter seconds 1second transmitter seconds second and then off 2 Pairing with a Bluetooth device After the transmitter connecting to a Bluetooth stereo receiver you can enjoy music wirelessly Before pairing please make sure your Bluetooth stereo receiver supports Bluetooth A2DP profile The pairing steps are as follows 1 Make sure the transmitter is off otherwise switch it off 2 Keep the transmitter and your Bluetooth stereo receiver within 1 meter 3 3 5 6 7 Switch on your Bluetooth stereo receiver and make it enter pairing mode Press and hold MFB button of the transmitter for 5 7 seconds and do not release it until red and blue LEDs flash alternately at this time the transmitter entered pairing mode The transmitter will automatically search for Bluetooth stereo receiver and finish connection After successful connecting blue LED of the transmitter flashes tw
Download Pdf Manuals
Related Search