User Manual - Universal Fibre Optics
Contents
1. Optics UNIVERSAL FIBRE OPTICS Universal Fibre Optics Home Place Coldstream TD12 4DT United Kingdom Tel 44 0 1890 883416 Fax 44 0 1890 883062 www fibreopticlighting com2. POWER SUPPLY REQUIREMENTS Before plugging in the unit please make sure that the supply is correct Failure to do so could cause the unit to malfunction The unit requires a 240VAC 50Hz supply and it MUST BE EARTHED The light source units are provided with a cordset fitted with a standard 3 pin plug POSITIONING THE UNIT Standard horizontal mounting on shelf table Vertical mounting fixed to wall Upside down mounting fixed to underside of shelf The light source can be mounted horizontally vertically or upside down on any flat surface Keyhole slots are provided on the base of the unit to allow for securing to a surface The light source is only suitable for use in a dry area If the unit is being mounted at a higher than the ground level block access below the work area before installing Verify that any screws or bolts can safely bear the weight of the light source Universal Fibre Optics a INSTALLATION GUIDE Continued Verify that the supporting structure can safely bear the weight of all installed units cables and any other equipment The minimum thickness of the mounting surface must be no less than 19mm For horizontal mounting it is recommended that the lightsource is secured to a solid surface using 4 x M4 or M5 screws or bolts and the keyhole slots This is particularly important if the lightsource location is not at ground floor level To mount the light source vertically first securely instal
3. FIPA Le mn 4 inte Light Source User Guide Compact Light Source Range Models covered by this manual UFO 70 150 CG Glass White Light 240V UFO 70 150 CP Plastic White Light 240V UFO 70 150 CGC Glass Colour Wheel continuous 240V UFO 70 150 CPC Plastic Colour Wheel continuous 240V UFO 70 150 CGS Glass Colour Wheel switch on box 240V UFO 70 150 CPS Plastic Colour Wheel switch on box 240V UFO 70 150 CGCF Glass Colour Wheel separate feed 240V UFO 70 150 CPCF Plastic Colour Wheel separate feed 240V Universal Fibre Optics Home Place Coldstream TD12 4DT United Kingdom Tel 44 0 1890 883416 Fax 44 0 1890 883062 www fibreopticlighting com Issue 2 Revised 10092013 INTRODUCTION Thank you for purchasing this UFO Light Source Please read these instructions fully before connecting your unit to the electrical supply and keep them for future reference The UFO Compact light sources are a range of low profile light sources which use either 70W or 150W metal halide discharge lamps to give much greater brightness than those powered by halogen lamps These models have a fast re lamping feature the lamp is mounted on a pull out hatch at the rear and can be fitted with a combination of colour twinkle or dimmer wheels for providing lighting effects We do not recommend that the light source be left on for 24 hours a day 7 days a week as lamp life will be impaired A switch off of 30mi
4. l 4 x M4 or M5 screws or bolts at the required distances so that they will line up with the keyhole slots The light source can then be mounted onto them and slid into position The bolts or screws MUST then be fully tightened To mount the light source under a surface first securely install 4 x M4 or M5 screws or bolts at the required distances so that they will line up with the keyhole slots The light source can then be mounted onto them and slid into position The bolts or screws MUST then be fully tightened 273mm 152mm CLEARANCE VENTILATION It is imperative that a gap of 200mm 8 or more is left around the unit This is to allow air to circulate and prevent overheating The location must have free ventilation zl Compact Light Source Range INSTALLATION GUIDE Continued CONNECTION There are 2 main connections required the fibre port and the mains power supply On separate feed units there are two power connections Connect and secure the fibre optic connector to the fibre port before connecting the electrical supply Never run the light source with the fibre connector unplugged Fibre connector Power re OPERATION Switch on the power to the light source and it will start up automatically Light will be output from the port connector and throughout the fibre harness If no light is produced please consult the TROUBLESHOOTING section in this manual WHEEL CONTROL Decorative models of the Compact a
5. ns per day is recommended METAL HALIDE LAMPS CANNOT BE CONNECTED TO A MAINS DIMMER OR A REDUCED SUPPLY VOLTAGE THIS WILL RESULT IN DAMAGE TO THE LAMP AND AND THE ELECTRONIC BALLAST IMPORTANT THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED Do not operate without complete lamp enclosure in place or if lens is damaged KEEP HARNESS IN PLACE WHEN IN OPERATION CAUTION Hot surface Keep away from curtains and other combustible materials WARNING RISK OF FIRE INJURY TO PERSONS Keep away from combustibles Unplug to change lamp Do not touch lamp WARNING RISK OF FIRE Do not place lamp where the overhead surface is closer than 0 2m to the light source a Compact Light Source Range IMPORTANT SAFETY INFORMATION INSTRUCTIONS PERTAINING TO A RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS IMPORTANT SAFETY INSTRUCTIONS Lighted Lamp is HOT WARNING To reduce the risk of FIRE ELECTRIC SHOCK OR INJURY TO PERSONS Unplug and allow to cool before replacing lamp Lamp gets HOT quickly Only contact plug when turning on Do not touch hot lens guard or enclosure Do not remain in light if skin feels warm Do not look directly at lighted lamp Keep lamp away from materials that may burn Use only with the correct lamp wattage as detailed on the serial label Failure to adhere to this
6. r There is also a spare fuse located in this drawer 3 Open the fuse drawer 4 Withdraw fuse from its holder 5 Replace with identically specified fuse see specification table in this manual 6 Close the fuse drawer and power up the light source 7 Compact Light Source Range MAINTENANCE Continued CLEANING THE UNIT Disconnect unit from power supply and allow to cool before attempting any cleaning of the unit A visual check of the unit should be completed every 12 months However cleaning should take place as and when required The body of the unit can be cleaned with a soft damp cloth do not use any abrasives on the unit The fans and vents should be kept clear by periodically blowing them out with compressed air Glass filter to be cleaned with soap and water then dried Please note that a record of all maintenance MUST be kept in the table below indicating what maintenance was undertaken and when This must be DATED for warranty purposes Date Maintenance Undertaken Universal Fibre Optics 8 TROUBLESHOOTING Problem Probable cause s Remedy Unit is completely dead Check and replace fuse Lamp and LED power indicator are not No powerto unit Check that power is switched on illuminated and power supply is plugged in Allow unit to cool for 5 to 10 Thermal switch gt i minutes and investigate reason activated LED power indicator amp for overheating fan are on but no light is o
7. re available with a number of different colourwheel control options The control system available will depend on the exact model specified Continuous rotation the wheel rotates continuously and cannot be stopped White light only output is available by removing the wheel as detailed on page 8 of this manual Separate feed the wheel is controlled by a secondary mains electrical feed It can be started and stopped on any colour by simply switching the power off Switch control the wheel can be started and stopped by using a switch built into the back of the unit Universal Fibre Optics G MAINTENANCE LAMP REPLACEMENT Recommend Lamp change every 12 months for Metal Halide Lamps should not be run to the end of their life 1 Unplug unit from electrical supply and allow to cool 2 On the rear of the unit unscrew the two knurled securing nuts A which hold the lamp holder in position 3 Use the handle B to withdraw the lamp holder C from the light source 4 Unplug the old lamp from its ceramic holder 5 Plug the new lamp into the holder making sure that you use a bulb of the same specification as to that which was removed Also make sure not to touch the glass part of the lamp 6 Slide the lamp holder plate back into position and tighten the two retaining nuts FUSE REPLACEMENT 1 Unplug unit from electrical supply and allow to cool 2 The fuse is located in a drawer under the mains input connecto
8. utput Check plug connection ensure Lamp wires are not lamp is properly seated in its connected holder and the pins are fully mated Lamp needs replacing Replace lamp Clean glass lens with soap and Unit needs cleaning a Poor light output Incorrect power supply no power supply is 240VAC Ensure fibre port connector is plugged in correctly and that the screw is tightened up properly Fibre port connector not plugged in correctly Allow unit to cool for 5 to 10 Unit is overheating minutes and investigate reason for overheating Lamp going on amp off randomly Please complete troubleshooting procedures before returning unit to us for further investigation gt Compact Light Source Range TECHNICAL SPECIFICATIONS Description 70W White Light 70W Decorative 150W White Light 150W Decorative Lamp model Philips CDM T or Philips CDM T or Philips CDM SA T Philips CDM SA T CDM CDM or CDM or CDM Lamp life c 12000h c 12000h c 9000h SA T c 9000h SA T c 12000h CDM c 12000h CDM Lamp colour temp 4200K CDM T 4200K CDM T 4200K SA T 4200K SA T 3000K CDM 3000K CDM 3000K CDM 3000K CDM Lamp CRI 92 CDM T 92 CDM T 95 SA T 95 SA T 84 CDM 84 CDM 88 CDM 88 CDM Acoustic rating polymer 38 0dB A 38 0dB A 38 0dB A 38 0dB A fibre Acoustic rating glass 23 0dB A 23 0dB A 23 0dB A 23 0dB A fibre lamp life as stated by manufacturer in optimum conditions Universal Fibre
9. will cause damage to the unit Do not touch the lamp at any time Use a soft cloth Oil from skin may damage lamp 9 Do not operate product with missing or damaged guard lamp containme barrier lens or fibre optic harness 10 WARNING Lamp types are matched to the ballast and different wattages types cannot be used APA eS O 29 SAVE THESE INSTRUCTIONS e Always disconnect the unit from the power supply before opening or attempting to perform any work on it e UNIT MAY GET HOT always allow unit to cool down before handling or moving it e Do not touch or attempt to remove the lamp while it is hot e Ensure that the power supply is correct for the unit before powering it up e Always ensure that the unit is properly EARTHED e Do not expose the unit to rain or moisture e Keep away from all combustible materials e Never attempt to tamper with the wiring or other internal components e Keep the unit away from gas oil and any other flammable or explosive materials Universal Fibre Optics a LIGHTSOURCE LAYOUT Item Description Piper 2 LEE O O O OOO Blanking plate or colour wheel switch depending on specification a T Motor cover decorative unison i Cra a Compact Light Source Range INSTALLATION GUIDE In order for the Compact light source to function safely and efficiently it must be installed according to this user manual Please read all sections thoroughly before switching on the light source
Download Pdf Manuals
Related Search